All of lore.kernel.org
 help / color / mirror / Atom feed
From: David Brownell <david-b@pacbell.net>
To: spi-devel-general@lists.sourceforge.net, joakim.tjernlund@transmode.se
Cc: 'linuxppc-dev Development' <linuxppc-dev@ozlabs.org>
Subject: Re: [spi-devel-general] [PATCH] Adapt spi_mpc83xx SPI driver for	832x
Date: Fri, 22 Dec 2006 17:09:31 -0800	[thread overview]
Message-ID: <200612221709.31714.david-b@pacbell.net> (raw)
In-Reply-To: <1166090567.30422.73.camel@gentoo-jocke.transmode.se>

On Thursday 14 December 2006 2:02 am, Joakim Tjernlund wrote:

> Adjusted patch(lets hope I didn't mangle this one:):

Assuming this is correct, I don't have a problem with this one.
Feel free to wrap it up with a signed-off-by and I'll forward it.


I have a question for someone who knows about this controller though...

When issuing an RX-only transfer, the SPI framework currently specifies
that spi_transfer.tx_buf will be null, and that the data shifted out
on the MOSI pin is "undefined".  Looking at the spi_mpc83xx driver in
the current tree, it looked to me as if it wouldn't actually accept
a null tx_buf ... did I miss something, or would the tx_buf##type macros
expand to a null pointer exception?  If I did miss something, what data
would be shifted out in that case?  (IRQ vectors from page zero?)

There's a proposal afoot to change how that's specified:  rather than
shifting out "undefined" data, define it as all zeroes.  It was easy
to see the impact of that on all the other SPI controller drivers now
upstream; all but one send zeroes already.  But not this one...

- Dave


> diff --git a/drivers/spi/spi_mpc83xx.c b/drivers/spi/spi_mpc83xx.c
> index ff0b048..0c31878 100644
> --- a/drivers/spi/spi_mpc83xx.c
> +++ b/drivers/spi/spi_mpc83xx.c
> @@ -47,6 +47,7 @@ struct mpc83xx_spi_reg {
>  #define	SPMODE_ENABLE		(1 << 24)
>  #define	SPMODE_LEN(x)		((x) << 20)
>  #define	SPMODE_PM(x)		((x) << 16)
> +#define	SPMODE_OP		(1 << 14)
>  
>  /*
>   * Default for SPI Mode:
> @@ -85,6 +86,11 @@ struct mpc83xx_spi {
>  	unsigned nsecs;		/* (clock cycle time)/2 */
>  
>  	u32 sysclk;
> +	u32 rx_shift;		/* amount to adjust RX data regs if in qe mode */
> +	u32 tx_shift;		/* amount to adjust TX data regs if in qe mode */
> +
> +	bool qe_mode;
> +
>  	void (*activate_cs) (u8 cs, u8 polarity);
>  	void (*deactivate_cs) (u8 cs, u8 polarity);
>  };
> @@ -103,7 +109,7 @@ static inline u32 mpc83xx_spi_read_reg(_
>  void mpc83xx_spi_rx_buf_##type(u32 data, struct mpc83xx_spi *mpc83xx_spi) \
>  {									  \
>  	type * rx = mpc83xx_spi->rx;					  \
> -	*rx++ = (type)data;						  \
> +	*rx++ = (type)(data >> mpc83xx_spi->rx_shift);			  \
>  	mpc83xx_spi->rx = rx;						  \
>  }
>  
> @@ -112,7 +118,7 @@ u32 mpc83xx_spi_tx_buf_##type(struct mpc
>  {								\
>  	u32 data;						\
>  	const type * tx = mpc83xx_spi->tx;			\
> -	data = *tx++;						\
> +	data = *tx++ << mpc83xx_spi->tx_shift;			\
>  	mpc83xx_spi->tx = tx;					\
>  	return data;						\
>  }
> @@ -195,12 +201,22 @@ int mpc83xx_spi_setup_transfer(struct sp
>  	    || ((bits_per_word > 16) && (bits_per_word != 32)))
>  		return -EINVAL;
>  
> +	mpc83xx_spi->rx_shift = 0;
> +	mpc83xx_spi->tx_shift = 0;
>  	if (bits_per_word <= 8) {
>  		mpc83xx_spi->get_rx = mpc83xx_spi_rx_buf_u8;
>  		mpc83xx_spi->get_tx = mpc83xx_spi_tx_buf_u8;
> +		if (mpc83xx_spi->qe_mode) {
> +			mpc83xx_spi->rx_shift = 16;
> +			mpc83xx_spi->tx_shift = 24;
> +		}
>  	} else if (bits_per_word <= 16) {
>  		mpc83xx_spi->get_rx = mpc83xx_spi_rx_buf_u16;
>  		mpc83xx_spi->get_tx = mpc83xx_spi_tx_buf_u16;
> +		if (mpc83xx_spi->qe_mode) {
> +			mpc83xx_spi->rx_shift = 16;
> +			mpc83xx_spi->tx_shift = 16;
> +		}
>  	} else if (bits_per_word <= 32) {
>  		mpc83xx_spi->get_rx = mpc83xx_spi_rx_buf_u32;
>  		mpc83xx_spi->get_tx = mpc83xx_spi_tx_buf_u32;
> @@ -369,8 +385,8 @@ static int __init mpc83xx_spi_probe(stru
>  		ret = -ENODEV;
>  		goto free_master;
>  	}
> -
>  	mpc83xx_spi = spi_master_get_devdata(master);
> +	pdata->qe_mode = 1; // temp hack to force 832x mode
>  	mpc83xx_spi->bitbang.master = spi_master_get(master);
>  	mpc83xx_spi->bitbang.chipselect = mpc83xx_spi_chipselect;
>  	mpc83xx_spi->bitbang.setup_transfer = mpc83xx_spi_setup_transfer;
> @@ -378,9 +394,17 @@ static int __init mpc83xx_spi_probe(stru
>  	mpc83xx_spi->sysclk = pdata->sysclk;
>  	mpc83xx_spi->activate_cs = pdata->activate_cs;
>  	mpc83xx_spi->deactivate_cs = pdata->deactivate_cs;
> +	mpc83xx_spi->qe_mode = pdata->qe_mode;
>  	mpc83xx_spi->get_rx = mpc83xx_spi_rx_buf_u8;
>  	mpc83xx_spi->get_tx = mpc83xx_spi_tx_buf_u8;
>  
> +	mpc83xx_spi->rx_shift = 0;
> +	mpc83xx_spi->tx_shift = 0;
> +	if (mpc83xx_spi->qe_mode) {
> +		mpc83xx_spi->rx_shift = 16;
> +		mpc83xx_spi->tx_shift = 24;
> +	}
> +
>  	mpc83xx_spi->bitbang.master->setup = mpc83xx_spi_setup;
>  	init_completion(&mpc83xx_spi->done);
>  
> @@ -415,6 +439,9 @@ static int __init mpc83xx_spi_probe(stru
>  
>  	/* Enable SPI interface */
>  	regval = pdata->initial_spmode | SPMODE_INIT_VAL | SPMODE_ENABLE;
> +	if (pdata->qe_mode)
> +		regval |= SPMODE_OP;
> +
>  	mpc83xx_spi_write_reg(&mpc83xx_spi->base->mode, regval);
>  
>  	ret = spi_bitbang_start(&mpc83xx_spi->bitbang);
> 
> 
> 

  parent reply	other threads:[~2006-12-23  1:09 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2006-12-13  9:22 [PATCH] Adapt spi_mpc83xx SPI driver for 832x Joakim Tjernlund
2006-12-13  9:44 ` Vitaly Wool
2006-12-13  9:53 ` Li Yang-r58472
2006-12-13 14:46 ` Kumar Gala
2006-12-13 15:36   ` Joakim Tjernlund
2006-12-13 20:31     ` [spi-devel-general] " David Brownell
2006-12-14  0:13       ` Joakim Tjernlund
2006-12-14  5:54         ` Kumar Gala
2006-12-14 10:02           ` Joakim Tjernlund
2006-12-14 19:59             ` Reeve Yang
2006-12-14 20:12               ` Ben Warren
2006-12-14 20:39                 ` Reeve Yang
2006-12-14 21:30                   ` Ben Warren
2006-12-23  1:09             ` David Brownell [this message]
2006-12-26 16:31               ` Kumar Gala
2007-02-17  2:17             ` David Brownell
2007-02-17  9:14               ` Joakim Tjernlund
2006-12-23  0:57         ` David Brownell

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=200612221709.31714.david-b@pacbell.net \
    --to=david-b@pacbell.net \
    --cc=joakim.tjernlund@transmode.se \
    --cc=linuxppc-dev@ozlabs.org \
    --cc=spi-devel-general@lists.sourceforge.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.