Re: [PATCH] bcm43xx: Fix loss of association after resume

[Michael Buesch <mb@bu3sch.de>]

On Sunday 11 February 2007 15:02, Rafael J. Wysocki wrote:
> On Sunday, 11 February 2007 14:07, Michael Buesch wrote:
> > On Sunday 11 February 2007 13:56, Rafael J. Wysocki wrote:
> > > On Saturday, 10 February 2007 21:33, Larry Finger wrote:
> > > > Rafael,
> > > > 
> > > > Rafael J. Wysocki wrote:
> > > > > 
> > > > > I'm running with this patch applied right now, but the association is lost
> > > > > after the resume anyway.  I have to reload bcm43xx to make it associate with
> > > > > the AP again (no big deal).
> > > > 
> > > > 
> > > > Please send me the output of iwconfig and ifconfig after the resume, but before you reload bcm43xx.
> > > 
> > > albercik:~ # iwconfig
> > > lo        no wireless extensions.
> > > 
> > > eth0      no wireless extensions.
> > > 
> > > eth1      IEEE 802.11b/g  ESSID:"DI524"  Nickname:"Broadcom 4311"
> > >           Mode:Managed  Frequency=2.484 GHz  Access Point: Invalid
> > >           Bit Rate=1 Mb/s   Tx-Power=18 dBm
> > >           RTS thr:off   Fragment thr:off
> > >           Encryption key:off
> > >           Link Quality=0/100  Signal level=-256 dBm  Noise level=-256 dBm
> > >           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
> > >           Tx excessive retries:0  Invalid misc:0   Missed beacon:0
> > > 
> > > albercik:~ # ifconfig eth1
> > > eth1      Link encap:Ethernet  HWaddr 00:14:A5:BE:95:31
> > >           inet addr:192.168.100.101  Bcast:192.168.100.255  Mask:255.255.255.0
> > >           inet6 addr: fe80::214:a5ff:febe:9531/64 Scope:Link
> > >           UP BROADCAST MULTICAST  MTU:1500  Metric:1
> > >           RX packets:5137 errors:0 dropped:120 overruns:0 frame:0
> > >           TX packets:5703 errors:0 dropped:0 overruns:0 carrier:0
> > >           collisions:0 txqueuelen:1000
> > >           RX bytes:4569090 (4.3 Mb)  TX bytes:156826797 (149.5 Mb)
> > >           Interrupt:18
> > > 
> > > albercik:~ # ifconfig eth1 down
> > > albercik:~ # ifconfig eth1 up
> > > SIOCSIFFLAGS: No such device
> > 		^^^^^
> > 
> > I'd like to see dmesg, please.
> 
> Appended.  It covers one suspend-resume cycle (suspend to disk).  I have
> filtered HID-related messages out of it.
> 
> Greetings,
> Rafael
> 
> 
> ton.000e = 0
> usb 3-1: usb auto-resume
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00040103 PSSC PPS PES CCS
> usb 3-1: finish resume
> usb usb1: usb auto-resume
> usb usb1: finish resume
> hub 1-0:1.0: hub_resume
> ehci_hcd 0000:00:13.2: resume root hub
> hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
> usb 3-1: usb auto-suspend
> hub 1-0:1.0: hub_suspend
> usb usb1: usb auto-suspend
> PM: Adding info for No Bus:vcs8
> PM: Adding info for No Bus:vcsa8
> SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
> Stopping tasks ... done.
> Shrinking memory...  \b-\b\\b|\b/\b-\b\\b|\b/\b-\b\\bdone (113015 pages freed)
> Freed 452060 kbytes in 1.44 seconds (313.93 MB/s)
> Suspending console(s)
> usbhid 3-4:1.0: freeze
> usb 3-4: freeze
> usbhid 3-4:1.0: suspend
> usb 3-4: usb suspend
>  usbdev3.18: PM: suspend 0->1, parent 3-1 already 2
>  usbdev3.18_ep02: PM: suspend 0->1, parent 3-1:1.0 already 2
>  usbdev3.18_ep81: PM: suspend 0->1, parent 3-1:1.0 already 2
> usb 3-1:1.0: PM: suspend 2-->1
> usb 3-1:1.0: PM: suspend 2->1, parent 3-1 already 2
>  usbdev3.18_ep00: PM: suspend 0->1, parent 3-1 already 2
> usb 3-1: PM: suspend 2-->1
> usb 2-2:1.3: freeze
> usb 2-2:1.2: freeze
> hci_usb 2-2:1.1: freeze
> hci_usb 2-2:1.0: freeze
> usb 2-2: freeze
> usb 2-2: usb suspend
> serio serio6: freeze
> platform bluetooth: freeze
> hub 3-0:1.0: freeze
> usb usb3: freeze
> hub 3-0:1.0: hub_suspend
> ohci_hcd 0000:00:13.1: suspend root hub
> usb usb3: usb suspend
> hub 2-0:1.0: freeze
> usb usb2: freeze
> hub 2-0:1.0: hub_suspend
> ohci_hcd 0000:00:13.0: suspend root hub
> usb usb2: usb suspend
>  usbdev1.1: PM: suspend 0->1, parent usb1 already 2
>  usbdev1.1_ep81: PM: suspend 0->1, parent 1-0:1.0 already 2
> hub 1-0:1.0: PM: suspend 2-->1
> hub 1-0:1.0: PM: suspend 2->1, parent usb1 already 2
>  usbdev1.1_ep00: PM: suspend 0->1, parent usb1 already 2
> usb usb1: PM: suspend 2-->1
> ide-cdrom 0.0: freeze
> psmouse serio4: freeze
> serio serio3: freeze
> serio serio2: freeze
> serio serio1: freeze
> atkbd serio0: freeze
> i8042 i8042: freeze
> sd 0:0:0:0: freeze
> serial8250 serial8250: freeze
> vesafb vesafb.0: freeze
> pci_express 0000:00:06.0:pcie03: freeze
> pci_express 0000:00:06.0:pcie01: freeze
> pci_express 0000:00:06.0:pcie00: freeze
> pci_express 0000:00:05.0:pcie03: freeze
> pci_express 0000:00:05.0:pcie01: freeze
> pci_express 0000:00:05.0:pcie00: freeze
> pci_express 0000:00:04.0:pcie03: freeze
> pci_express 0000:00:04.0:pcie01: freeze
> pci_express 0000:00:04.0:pcie00: freeze
> pcspkr pcspkr: freeze
> sdhci 0000:02:04.3: freeze
> ACPI: PCI interrupt for device 0000:02:04.3 disabled
> tifm_7xx1 0000:02:04.2: freeze
> ACPI: PCI interrupt for device 0000:02:04.2 disabled
> ohci1394 0000:02:04.1: freeze
> ohci1394 does not fully support suspend and resume yet
> ieee1394: hpsb_bus_reset called while bus reset already in progress
> yenta_cardbus 0000:02:04.0: freeze
> tg3 0000:02:01.0: freeze
> PM: Writing back config space on device 0000:02:01.0 at offset b (was 3ed173b, writing 30b0103c)
> PM: Writing back config space on device 0000:02:01.0 at offset 3 (was 0, writing 4010)
> PM: Writing back config space on device 0000:02:01.0 at offset 2 (was 2000000, writing 2000003)
> PM: Writing back config space on device 0000:02:01.0 at offset 1 (was 2b00000, writing 2b00006)
> PM: Writing back config space on device 0000:02:01.0 at offset 0 (was 3ed173b, writing 169c14e4)
> bcm43xx 0000:30:00.0: freeze
> bcm43xx: Suspending...
> PM: Removing info for No Bus:hw_random
> bcm43xx: Radio turned off
> bcm43xx: DMA-32 0x0200 (RX) max used slots: 3/64
> bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
> bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
> bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
> bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
> bcm43xx: DMA-32 0x0220 (TX) max used slots: 3/512
> bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
> ACPI: PCI interrupt for device 0000:30:00.0 disabled
> bcm43xx: Device suspended.
> pci 0000:01:05.0: freeze
> k8temp 0000:00:18.3: freeze
> pci 0000:00:18.2: freeze
> pci 0000:00:18.1: freeze
> pci 0000:00:18.0: freeze
> pci 0000:00:14.4: freeze
> pci 0000:00:14.3: freeze
> HDA Intel 0000:00:14.2: freeze
> ACPI: PCI interrupt for device 0000:00:14.2 disabled
> ATIIXP_IDE 0000:00:14.1: freeze
> piix4_smbus 0000:00:14.0: freeze
> ehci_hcd 0000:00:13.2: freeze
> ACPI: PCI interrupt for device 0000:00:13.2 disabled
> ehci_hcd 0000:00:13.2: --> PCI D3
> ohci_hcd 0000:00:13.1: freeze
> ACPI: PCI interrupt for device 0000:00:13.1 disabled
> ohci_hcd 0000:00:13.1: --> PCI D0/legacy
> ohci_hcd 0000:00:13.0: freeze
> ACPI: PCI interrupt for device 0000:00:13.0 disabled
> ohci_hcd 0000:00:13.0: --> PCI D0/legacy
> sata_sil 0000:00:12.0: freeze
> pcieport-driver 0000:00:06.0: freeze
> pcieport-driver 0000:00:05.0: freeze
> pcieport-driver 0000:00:04.0: freeze
> pci 0000:00:01.0: freeze
> pci 0000:00:00.0: freeze
> ACPI Thermal Zone Driver thermal:03: freeze
> ACPI Thermal Zone Driver thermal:02: freeze
> ACPI Thermal Zone Driver thermal:01: freeze
> ACPI Fan Driver PNP0C0B:03: freeze
> ACPI Fan Driver PNP0C0B:02: freeze
> ACPI: Transitioning device [C351] to D0
> ACPI: Transitioning device [C351] to D0
> ACPI Fan Driver PNP0C0B:01: freeze
> ACPI: Transitioning device [C350] to D0
> ACPI: Transitioning device [C350] to D0
> ACPI Fan Driver PNP0C0B:00: freeze
> ACPI: Transitioning device [C34F] to D0
> ACPI: Transitioning device [C34F] to D0
> ACPI Power Resource Driver power_resource:06: freeze
> ACPI Power Resource Driver power_resource:05: freeze
> ACPI Power Resource Driver power_resource:04: freeze
> ACPI Power Resource Driver power_resource:03: freeze
> acpi thermal:00: freeze
> acpi PNP0C02:02: freeze
> acpi PNP0C14:00: freeze
> ACPI Button Driver PNP0C0D:00: freeze
> ACPI Button Driver PNP0C0E:00: freeze
> ACPI AC Adapter Driver ACPI0003:00: freeze
> ACPI Battery Driver PNP0C0A:01: freeze
> ACPI Battery Driver PNP0C0A:00: freeze
> acpi HPQ0006:00: freeze
> acpi PNP0C02:01: freeze
> acpi device:49: freeze
> acpi device:48: freeze
> acpi device:47: freeze
> acpi device:46: freeze
> acpi device:45: freeze
> acpi device:44: freeze
> acpi device:43: freeze
> acpi device:42: freeze
> acpi device:41: freeze
> acpi device:40: freeze
> acpi device:3f: freeze
> acpi device:3e: freeze
> acpi device:3d: freeze
> acpi device:3c: freeze
> acpi device:3b: freeze
> acpi device:3a: freeze
> acpi device:39: freeze
> acpi device:38: freeze
> acpi device:37: freeze
> acpi device:36: freeze
> acpi device:35: freeze
> acpi device:34: freeze
> acpi device:33: freeze
> ACPI PCI Interrupt Link Driver PNP0C0F:07: freeze
> ACPI PCI Interrupt Link Driver PNP0C0F:06: freeze
> ACPI PCI Interrupt Link Driver PNP0C0F:05: freeze
> ACPI PCI Interrupt Link Driver PNP0C0F:04: freeze
> ACPI PCI Interrupt Link Driver PNP0C0F:03: freeze
> ACPI PCI Interrupt Link Driver PNP0C0F:02: freeze
> ACPI PCI Interrupt Link Driver PNP0C0F:01: freeze
> ACPI PCI Interrupt Link Driver PNP0C0F:00: freeze
> acpi device:32: freeze
> acpi device:31: freeze
> acpi device:30: freeze
> acpi device:2f: freeze
> acpi device:2e: freeze
> acpi device:2d: freeze
> acpi device:2c: freeze
> acpi device:2b: freeze
> acpi device:2a: freeze
> acpi device:29: freeze
> acpi device:28: freeze
> acpi device:27: freeze
> acpi device:26: freeze
> acpi device:25: freeze
> acpi device:24: freeze
> acpi device:23: freeze
> acpi device:22: freeze
> acpi device:21: freeze
> acpi device:20: freeze
> acpi device:1f: freeze
> acpi device:1e: freeze
> acpi device:1d: freeze
> acpi device:1c: freeze
> acpi device:1b: freeze
> acpi device:1a: freeze
> acpi device:19: freeze
> acpi device:18: freeze
> acpi device:17: freeze
> acpi device:16: freeze
> acpi device:15: freeze
> acpi device:14: freeze
> acpi device:13: freeze
> acpi device:12: freeze
> acpi device:11: freeze
> acpi device:10: freeze
> acpi PNP0C02:00: freeze
> acpi PNP0000:00: freeze
> ACPI Power Resource Driver power_resource:02: freeze
> acpi SYN0118:00: freeze
> acpi PNP0303:00: freeze
> acpi PNP0B00:00: freeze
> acpi PNP0800:00: freeze
> acpi PNP0200:00: freeze
> acpi PNP0100:00: freeze
> acpi PNP0C04:00: freeze
> acpi IFX0102:00: freeze
> ACPI Power Resource Driver power_resource:01: freeze
> acpi PNP0401:00: freeze
> ACPI container driver PNP0A06:00: freeze
> ACPI Embedded Controller Driver PNP0C09:00: freeze
> acpi device:0f: freeze
> acpi device:0e: freeze
> ACPI Power Resource Driver power_resource:00: freeze
> acpi device:0d: freeze
> acpi device:0c: freeze
> acpi device:0b: freeze
> acpi device:0a: freeze
> acpi device:09: freeze
> acpi device:08: freeze
> acpi device:07: freeze
> acpi device:06: freeze
> acpi device:05: freeze
> acpi device:04: freeze
> acpi device:03: freeze
> acpi device:02: freeze
> acpi video:00: freeze
> acpi device:01: freeze
> ACPI PCI Root Bridge Driver PNP0A03:00: freeze
> acpi PNP0C01:00: freeze
> acpi device:00: freeze
> ACPI Processor Driver ACPI0007:01: freeze
> ACPI Processor Driver ACPI0007:00: freeze
> ACPI Button Driver button_power:00: freeze
> acpi acpi_system:00: freeze
> Disabling non-boot CPUs ...
> CPU 1 is now offline
> SMP alternatives: switching to UP code
> CPU1 is down
> platform bluetooth: LATE freeze
> i8042 i8042: LATE freeze
> serial8250 serial8250: LATE freeze
> vesafb vesafb.0: LATE freeze
> pcspkr pcspkr: LATE freeze
> sdhci 0000:02:04.3: LATE freeze
> tifm_7xx1 0000:02:04.2: LATE freeze
> ohci1394 0000:02:04.1: LATE freeze
> yenta_cardbus 0000:02:04.0: LATE freeze
> tg3 0000:02:01.0: LATE freeze
> bcm43xx 0000:30:00.0: LATE freeze
> pci 0000:01:05.0: LATE freeze
> k8temp 0000:00:18.3: LATE freeze
> pci 0000:00:18.2: LATE freeze
> pci 0000:00:18.1: LATE freeze
> pci 0000:00:18.0: LATE freeze
> pci 0000:00:14.4: LATE freeze
> pci 0000:00:14.3: LATE freeze
> HDA Intel 0000:00:14.2: LATE freeze
> ATIIXP_IDE 0000:00:14.1: LATE freeze
> piix4_smbus 0000:00:14.0: LATE freeze
> pcieport-driver 0000:00:06.0: LATE freeze
> pcieport-driver 0000:00:05.0: LATE freeze
> pcieport-driver 0000:00:04.0: LATE freeze
> pci 0000:00:01.0: LATE freeze
> pci 0000:00:00.0: LATE freeze
> Extended CMOS year: 2000
> swsusp: critical section: 
> swsusp: Need to copy 95157 pages
> swsusp: Normal pages needed: 95157 + 1024 + 20, available pages: 134073
> Extended CMOS year: 2000
> pci 0000:00:00.0: EARLY resume
> pci 0000:00:01.0: EARLY resume
> pcieport-driver 0000:00:04.0: EARLY resume
> pcieport-driver 0000:00:05.0: EARLY resume
> pcieport-driver 0000:00:06.0: EARLY resume
> sata_sil 0000:00:12.0: EARLY resume
> ohci_hcd 0000:00:13.0: EARLY resume
> ohci_hcd 0000:00:13.1: EARLY resume
> ehci_hcd 0000:00:13.2: EARLY resume
> piix4_smbus 0000:00:14.0: EARLY resume
> ATIIXP_IDE 0000:00:14.1: EARLY resume
> HDA Intel 0000:00:14.2: EARLY resume
> pci 0000:00:14.3: EARLY resume
> pci 0000:00:14.4: EARLY resume
> pci 0000:00:18.0: EARLY resume
> pci 0000:00:18.1: EARLY resume
> pci 0000:00:18.2: EARLY resume
> k8temp 0000:00:18.3: EARLY resume
> pci 0000:01:05.0: EARLY resume
> bcm43xx 0000:30:00.0: EARLY resume
> tg3 0000:02:01.0: EARLY resume
> yenta_cardbus 0000:02:04.0: EARLY resume
> ohci1394 0000:02:04.1: EARLY resume
> tifm_7xx1 0000:02:04.2: EARLY resume
> sdhci 0000:02:04.3: EARLY resume
> pcspkr pcspkr: EARLY resume
> vesafb vesafb.0: EARLY resume
> serial8250 serial8250: EARLY resume
> i8042 i8042: EARLY resume
> platform bluetooth: EARLY resume
> Enabling non-boot CPUs ...
> SMP alternatives: switching to SMP code
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 3990.23 BogoMIPS (lpj=7980462)
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 512K (64 bytes/line)
> CPU: Physical Processor ID: 0
> CPU: Processor Core ID: 1
> AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 02
> CPU 1: Syncing TSC to CPU 0.
> CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 510 cycles)
> powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x13
> powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x15
> powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x17
> powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x1e
> CPU1 is up
> acpi acpi_system:00: resuming
> ACPI Button Driver button_power:00: resuming
> ACPI Processor Driver ACPI0007:00: resuming
> ACPI Processor Driver ACPI0007:01: resuming
> acpi device:00: resuming
> acpi PNP0C01:00: resuming
> ACPI PCI Root Bridge Driver PNP0A03:00: resuming
> acpi device:01: resuming
> acpi video:00: resuming
> acpi device:02: resuming
> acpi device:03: resuming
> acpi device:04: resuming
> acpi device:05: resuming
> acpi device:06: resuming
> acpi device:07: resuming
> acpi device:08: resuming
> acpi device:09: resuming
> acpi device:0a: resuming
> acpi device:0b: resuming
> acpi device:0c: resuming
> acpi device:0d: resuming
> ACPI Power Resource Driver power_resource:00: resuming
> acpi device:0e: resuming
> acpi device:0f: resuming
> ACPI Embedded Controller Driver PNP0C09:00: resuming
> ACPI container driver PNP0A06:00: resuming
> acpi PNP0401:00: resuming
> ACPI Power Resource Driver power_resource:01: resuming
> acpi IFX0102:00: resuming
> acpi PNP0C04:00: resuming
> acpi PNP0100:00: resuming
> acpi PNP0200:00: resuming
> acpi PNP0800:00: resuming
> acpi PNP0B00:00: resuming
> acpi PNP0303:00: resuming
> acpi SYN0118:00: resuming
> ACPI Power Resource Driver power_resource:02: resuming
> acpi PNP0000:00: resuming
> acpi PNP0C02:00: resuming
> acpi device:10: resuming
> acpi device:11: resuming
> acpi device:12: resuming
> acpi device:13: resuming
> acpi device:14: resuming
> acpi device:15: resuming
> acpi device:16: resuming
> acpi device:17: resuming
> acpi device:18: resuming
> acpi device:19: resuming
> acpi device:1a: resuming
> acpi device:1b: resuming
> acpi device:1c: resuming
> acpi device:1d: resuming
> acpi device:1e: resuming
> acpi device:1f: resuming
> acpi device:20: resuming
> acpi device:21: resuming
> acpi device:22: resuming
> acpi device:23: resuming
> acpi device:24: resuming
> acpi device:25: resuming
> acpi device:26: resuming
> acpi device:27: resuming
> acpi device:28: resuming
> acpi device:29: resuming
> acpi device:2a: resuming
> acpi device:2b: resuming
> acpi device:2c: resuming
> acpi device:2d: resuming
> acpi device:2e: resuming
> acpi device:2f: resuming
> acpi device:30: resuming
> acpi device:31: resuming
> acpi device:32: resuming
> ACPI PCI Interrupt Link Driver PNP0C0F:00: resuming
> ACPI PCI Interrupt Link Driver PNP0C0F:01: resuming
> ACPI PCI Interrupt Link Driver PNP0C0F:02: resuming
> ACPI PCI Interrupt Link Driver PNP0C0F:03: resuming
> ACPI PCI Interrupt Link Driver PNP0C0F:04: resuming
> ACPI PCI Interrupt Link Driver PNP0C0F:05: resuming
> ACPI PCI Interrupt Link Driver PNP0C0F:06: resuming
> ACPI PCI Interrupt Link Driver PNP0C0F:07: resuming
> acpi device:33: resuming
> acpi device:34: resuming
> acpi device:35: resuming
> acpi device:36: resuming
> acpi device:37: resuming
> acpi device:38: resuming
> acpi device:39: resuming
> acpi device:3a: resuming
> acpi device:3b: resuming
> acpi device:3c: resuming
> acpi device:3d: resuming
> acpi device:3e: resuming
> acpi device:3f: resuming
> acpi device:40: resuming
> acpi device:41: resuming
> acpi device:42: resuming
> acpi device:43: resuming
> acpi device:44: resuming
> acpi device:45: resuming
> acpi device:46: resuming
> acpi device:47: resuming
> acpi device:48: resuming
> acpi device:49: resuming
> acpi PNP0C02:01: resuming
> acpi HPQ0006:00: resuming
> ACPI Battery Driver PNP0C0A:00: resuming
> ACPI Battery Driver PNP0C0A:01: resuming
> ACPI AC Adapter Driver ACPI0003:00: resuming
> ACPI Button Driver PNP0C0E:00: resuming
> ACPI Button Driver PNP0C0D:00: resuming
> acpi PNP0C14:00: resuming
> acpi PNP0C02:02: resuming
> acpi thermal:00: resuming
> ACPI Power Resource Driver power_resource:03: resuming
> ACPI Power Resource Driver power_resource:04: resuming
> ACPI Power Resource Driver power_resource:05: resuming
> ACPI Power Resource Driver power_resource:06: resuming
> ACPI Fan Driver PNP0C0B:00: resuming
> ACPI: Transitioning device [C34F] to D0
> ACPI: Transitioning device [C34F] to D0
> ACPI Fan Driver PNP0C0B:01: resuming
> ACPI: Transitioning device [C350] to D0
> ACPI: Transitioning device [C350] to D0
> ACPI Fan Driver PNP0C0B:02: resuming
> ACPI: Transitioning device [C351] to D0
> ACPI: Transitioning device [C351] to D0
> ACPI Fan Driver PNP0C0B:03: resuming
> ACPI Thermal Zone Driver thermal:01: resuming
> ACPI Thermal Zone Driver thermal:02: resuming
> ACPI Thermal Zone Driver thermal:03: resuming
> pci 0000:00:00.0: resuming
> pci 0000:00:01.0: resuming
> pcieport-driver 0000:00:04.0: resuming
> PCI: Setting latency timer of device 0000:00:04.0 to 64
> pcieport-driver 0000:00:05.0: resuming
> PCI: Setting latency timer of device 0000:00:05.0 to 64
> pcieport-driver 0000:00:06.0: resuming
> PCI: Setting latency timer of device 0000:00:06.0 to 64
> sata_sil 0000:00:12.0: resuming
> ohci_hcd 0000:00:13.0: resuming
> ohci_hcd 0000:00:13.0: PCI legacy resume
> ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
> ohci_hcd 0000:00:13.1: resuming
> ohci_hcd 0000:00:13.1: PCI legacy resume
> ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
> ehci_hcd 0000:00:13.2: resuming
> ehci_hcd 0000:00:13.2: PCI D0, from previous PCI D3
> ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
> PM: Writing back config space on device 0000:00:13.2 at offset 1 (was 2b00007, writing 2b00017)
> ehci_hcd 0000:00:13.2: lost power, restarting
> usb usb1: root hub lost power or was reset
> ehci_hcd 0000:00:13.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
> ehci_hcd 0000:00:13.2: MWI active
> piix4_smbus 0000:00:14.0: resuming
> ATIIXP_IDE 0000:00:14.1: resuming
> ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
> HDA Intel 0000:00:14.2: resuming
> PM: Writing back config space on device 0000:00:14.2 at offset f (was 10a, writing a)
> PM: Writing back config space on device 0000:00:14.2 at offset 1 (was 4100006, writing 4100002)
> ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
> pci 0000:00:14.3: resuming
> pci 0000:00:14.4: resuming
> PM: Writing back config space on device 0000:00:14.4 at offset 6 (was 40030200, writing 40060200)
> pci 0000:00:18.0: resuming
> pci 0000:00:18.1: resuming
> pci 0000:00:18.2: resuming
> k8temp 0000:00:18.3: resuming
> pci 0000:01:05.0: resuming
> bcm43xx 0000:30:00.0: resuming
> bcm43xx: Resuming...
> ACPI: PCI Interrupt 0000:30:00.0[A] -> GSI 18 (level, low) -> IRQ 18
> bcm43xx: PHY connected
> bcm43xx: Microcode rev 0x127, pl 0xe (2005-04-18  02:36:27)
> bcm43xx: Radio turned on
> bcm43xx: Radio enabled by hardware
> ata2: SATA link down (SStatus 0 SControl 300)
> bcm43xx: Chip initialized
> bcm43xx: 32-bit DMA initialized
> bcm43xx: Keys cleared
> bcm43xx: Selected 802.11 core (phytype 2)
> PM: Adding info for No Bus:hw_random
> bcm43xx: Device resumed.
> tg3 0000:02:01.0: resuming
> PM: Writing back config space on device 0000:02:01.0 at offset b (was 3ed173b, writing 30b0103c)
> PM: Writing back config space on device 0000:02:01.0 at offset 3 (was 0, writing 4010)
> PM: Writing back config space on device 0000:02:01.0 at offset 2 (was 2000000, writing 2000003)
> PM: Writing back config space on device 0000:02:01.0 at offset 1 (was 2b00000, writing 2b00006)
> PM: Writing back config space on device 0000:02:01.0 at offset 0 (was 3ed173b, writing 169c14e4)
> SoftMAC: Associate: Scanning for networks first.
> yenta_cardbus 0000:02:04.0: resuming
> PM: Writing back config space on device 0000:02:04.0 at offset f (was 3c4010a, writing 5c0010a)
> PM: Writing back config space on device 0000:02:04.0 at offset 3 (was 824010, writing 82a810)
> ohci1394 0000:02:04.1: resuming
> ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[d4011000-d40117ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
> tifm_7xx1 0000:02:04.2: resuming
> ACPI: PCI Interrupt 0000:02:04.2[A] -> GSI 20 (level, low) -> IRQ 20
> sdhci 0000:02:04.3: resuming
> ACPI: PCI Interrupt 0000:02:04.3[A] -> GSI 20 (level, low) -> IRQ 20
> pcspkr pcspkr: resuming
> pci_express 0000:00:04.0:pcie00: resuming
> pci_express 0000:00:04.0:pcie01: resuming
> pci_express 0000:00:04.0:pcie03: resuming
> pci_express 0000:00:05.0:pcie00: resuming
> pci_express 0000:00:05.0:pcie01: resuming
> pci_express 0000:00:05.0:pcie03: resuming
> pci_express 0000:00:06.0:pcie00: resuming
> pci_express 0000:00:06.0:pcie01: resuming
> pci_express 0000:00:06.0:pcie03: resuming
> vesafb vesafb.0: resuming
> serial8250 serial8250: resuming
> sd 0:0:0:0: resuming
> i8042 i8042: resuming
> atkbd serio0: resuming
> serio serio1: resuming
> serio serio2: resuming
> serio serio3: resuming
> psmouse serio4: resuming
> synaptics reset failed
> synaptics reset failed
> synaptics reset failed
> SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
> ide-cdrom 0.0: resuming
> usb usb1: resuming
> usb usb1: usb resume
> usb usb1: finish resume
> hub 1-0:1.0: hub_resume
> ehci_hcd 0000:00:13.2: resume root hub after power loss
> usb usb2: resuming
> usb usb2: usb resume
> usb usb2: finish resume
> hub 2-0:1.0: hub_resume
> ohci_hcd 0000:00:13.0: BIOS/SMM active, control 008
> usb usb2: root hub lost power or was reset
> ohci_hcd 0000:00:13.0: resetting from state 'reset', control = 0x8
> ohci_hcd 0000:00:13.0: OHCI controller state
> ohci_hcd 0000:00:13.0: OHCI 1.0, NO legacy support registers
> ohci_hcd 0000:00:13.0: control 0x083 HCFS=operational CBSR=3
> ohci_hcd 0000:00:13.0: cmdstatus 0x00000 SOC=0
> ohci_hcd 0000:00:13.0: intrstatus 0x00000004 SF
> ohci_hcd 0000:00:13.0: intrenable 0x8000005a MIE RHSC UE RD WDH
> ohci_hcd 0000:00:13.0: hcca frame #0005
> ohci_hcd 0000:00:13.0: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
> ohci_hcd 0000:00:13.0: roothub.b 00000000 PPCM=0000 DR=0000
> ohci_hcd 0000:00:13.0: roothub.status 00008000 DRWE
> ohci_hcd 0000:00:13.0: roothub.portstatus [0] 0x00000100 PPS
> ohci_hcd 0000:00:13.0: roothub.portstatus [1] 0x00010100 CSC PPS
> ohci_hcd 0000:00:13.0: roothub.portstatus [2] 0x00000100 PPS
> ohci_hcd 0000:00:13.0: roothub.portstatus [3] 0x00000100 PPS
> ohci_hcd 0000:00:13.0: restart complete
> hub 2-0:1.0: resuming
> usb usb3: resuming
> usb usb3: usb resume
> usb usb3: finish resume
> hub 3-0:1.0: hub_resume
> ohci_hcd 0000:00:13.1: BIOS/SMM active, control 008
> usb usb3: root hub lost power or was reset
> ohci_hcd 0000:00:13.1: resetting from state 'reset', control = 0x8
> ohci_hcd 0000:00:13.1: OHCI controller state
> ohci_hcd 0000:00:13.1: OHCI 1.0, NO legacy support registers
> ohci_hcd 0000:00:13.1: control 0x083 HCFS=operational CBSR=3
> ohci_hcd 0000:00:13.1: cmdstatus 0x00000 SOC=0
> ohci_hcd 0000:00:13.1: intrstatus 0x00000004 SF
> ohci_hcd 0000:00:13.1: intrenable 0x8000005a MIE RHSC UE RD WDH
> ohci_hcd 0000:00:13.1: hcca frame #0005
> ohci_hcd 0000:00:13.1: roothub.a 02000204 POTPGT=2 NPS NDP=4(4)
> ohci_hcd 0000:00:13.1: roothub.b 00000000 PPCM=0000 DR=0000
> ohci_hcd 0000:00:13.1: roothub.status 00008000 DRWE
> ohci_hcd 0000:00:13.1: roothub.portstatus [0] 0x00010100 CSC PPS
> ohci_hcd 0000:00:13.1: roothub.portstatus [1] 0x00000100 PPS
> ohci_hcd 0000:00:13.1: roothub.portstatus [2] 0x00000100 PPS
> ohci_hcd 0000:00:13.1: roothub.portstatus [3] 0x00010100 CSC PPS
> ohci_hcd 0000:00:13.1: restart complete
> hub 3-0:1.0: resuming
> platform bluetooth: resuming
> serio serio6: resuming
> usb 2-2: resuming
>  usbdev2.10_ep00: PM: resume from 0, parent 2-2 still 1
> hci_usb 2-2:1.0: PM: resume from 1, parent 2-2 still 1
> hci_usb 2-2:1.0: resuming
>  hci0: PM: resume from 0, parent 2-2:1.0 still 1
>  usbdev2.10_ep81: PM: resume from 0, parent 2-2:1.0 still 1
>  usbdev2.10_ep82: PM: resume from 0, parent 2-2:1.0 still 1
>  usbdev2.10_ep02: PM: resume from 0, parent 2-2:1.0 still 1
> hci_usb 2-2:1.1: PM: resume from 1, parent 2-2 still 1
> hci_usb 2-2:1.1: resuming
>  usbdev2.10_ep83: PM: resume from 0, parent 2-2:1.1 still 1
>  usbdev2.10_ep03: PM: resume from 0, parent 2-2:1.1 still 1
> usb 2-2:1.2: PM: resume from 1, parent 2-2 still 1
> usb 2-2:1.2: resuming
>  usbdev2.10_ep84: PM: resume from 0, parent 2-2:1.2 still 1
>  usbdev2.10_ep04: PM: resume from 0, parent 2-2:1.2 still 1
> usb 2-2:1.3: PM: resume from 1, parent 2-2 still 1
> usb 2-2:1.3: resuming
>  usbdev2.10: PM: resume from 0, parent 2-2 still 1
>  usbdev3.18_ep00: PM: resume from 0, parent 3-1 still 2
>  usbdev3.18_ep81: PM: resume from 0, parent 3-1:1.0 still 2
>  usbdev3.18_ep02: PM: resume from 0, parent 3-1:1.0 still 2
>  usbdev3.18: PM: resume from 0, parent 3-1 still 2
> usb 3-4: resuming
>  usbdev3.19_ep00: PM: resume from 0, parent 3-4 still 1
> usbhid 3-4:1.0: PM: resume from 1, parent 3-4 still 1
> usbhid 3-4:1.0: resuming
>  usbdev3.19_ep81: PM: resume from 0, parent 3-4:1.0 still 1
>  usbdev3.19: PM: resume from 0, parent 3-4 still 1
> Restarting tasks ... <7>hub 2-0:1.0: state 7 ports 4 chg 0004 evt 001e
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [0] = 0x00010100 CSC PPS
> hub 2-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
> done.
> PM: Removing info for No Bus:vcs8
> PM: Removing info for No Bus:vcsa8
> ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
> ata1.00: configured for UDMA/100
> SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
> hub 2-0:1.0: port 2, status 0100, change 0001, 12 Mb/s
> usb 2-2: USB disconnect, address 10
> usb 2-2: unregistering device
> usb 2-2: usb_disable_device nuking all URBs
> usb 2-2: unregistering interface 2-2:1.0
> PM: Removing info for No Bus:usbdev2.10_ep81
>  usbdev2.10_ep81: ep_device_release called for usbdev2.10_ep81
> PM: Removing info for No Bus:usbdev2.10_ep82
>  usbdev2.10_ep82: ep_device_release called for usbdev2.10_ep82
> PM: Removing info for No Bus:usbdev2.10_ep02
>  usbdev2.10_ep02: ep_device_release called for usbdev2.10_ep02
> PM: Removing info for No Bus:hci0
> PM: Removing info for usb:2-2:1.0
> usb 2-2:1.0: uevent
> usb 2-2: unregistering interface 2-2:1.1
> PM: Removing info for No Bus:usbdev2.10_ep83
>  usbdev2.10_ep83: ep_device_release called for usbdev2.10_ep83
> PM: Removing info for No Bus:usbdev2.10_ep03
>  usbdev2.10_ep03: ep_device_release called for usbdev2.10_ep03
> PM: Removing info for usb:2-2:1.1
> usb 2-2:1.1: uevent
> usb 2-2: unregistering interface 2-2:1.2
> PM: Removing info for No Bus:usbdev2.10_ep84
>  usbdev2.10_ep84: ep_device_release called for usbdev2.10_ep84
> PM: Removing info for No Bus:usbdev2.10_ep04
>  usbdev2.10_ep04: ep_device_release called for usbdev2.10_ep04
> PM: Removing info for usb:2-2:1.2
> usb 2-2:1.2: uevent
> usb 2-2: unregistering interface 2-2:1.3
> PM: Removing info for usb:2-2:1.3
> usb 2-2:1.3: uevent
> PM: Removing info for No Bus:usbdev2.10
> PM: Removing info for No Bus:usbdev2.10_ep00
>  usbdev2.10_ep00: ep_device_release called for usbdev2.10_ep00
> PM: Removing info for usb:2-2
> usb 2-2: uevent
> SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
> hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
> hub 2-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
> hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [3] = 0x00010100 CSC PPS
> hub 2-0:1.0: port 4, status 0100, change 0001, 12 Mb/s
> hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
> hub 3-0:1.0: state 7 ports 4 chg 0012 evt 001e
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010100 CSC PPS
> hub 3-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
> usb 3-1: USB disconnect, address 18
> usb 3-1: unregistering device
> usb 3-1: usb_disable_device nuking all URBs
> usb 3-1: unregistering interface 3-1:1.0
> PM: Removing info for No Bus:usbdev3.18_ep81
>  usbdev3.18_ep81: ep_device_release called for usbdev3.18_ep81
> PM: Removing info for No Bus:usbdev3.18_ep02
>  usbdev3.18_ep02: ep_device_release called for usbdev3.18_ep02
> PM: Removing info for usb:3-1:1.0
> usb 3-1:1.0: uevent
> PM: Removing info for No Bus:usbdev3.18
> PM: Removing info for No Bus:usbdev3.18_ep00
>  usbdev3.18_ep00: ep_device_release called for usbdev3.18_ep00
> PM: Removing info for usb:3-1
> usb 3-1: uevent
> hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
> hub 3-0:1.0: port 2, status 0100, change 0001, 12 Mb/s
> hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
> hub 3-0:1.0: port 3, status 0100, change 0001, 12 Mb/s
> hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00010100 CSC PPS
> hub 3-0:1.0: port 4, status 0100, change 0001, 12 Mb/s
> usb 3-4: USB disconnect, address 19
> usb 3-4: unregistering device
> usb 3-4: usb_disable_device nuking all URBs
> usb 3-4: unregistering interface 3-4:1.0
> PM: Removing info for No Bus:usbdev3.19_ep81
>  usbdev3.19_ep81: ep_device_release called for usbdev3.19_ep81
> PM: Removing info for usb:3-4:1.0
> usb 3-4:1.0: uevent
> PM: Removing info for No Bus:usbdev3.19
> PM: Removing info for No Bus:usbdev3.19_ep00
>  usbdev3.19_ep00: ep_device_release called for usbdev3.19_ep00
> PM: Removing info for usb:3-4
> usb 3-4: uevent
> hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100
> hub 1-0:1.0: state 7 ports 8 chg 0000 evt 010c
> ehci_hcd 0000:00:13.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
> hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
> hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
> ehci_hcd 0000:00:13.2: port 2 full speed --> companion
> ehci_hcd 0000:00:13.2: GetStatus port 2 status 003801 POWER OWNER sig=j CONNECT
> hub 1-0:1.0: port 2 not reset yet, waiting 50ms
> ehci_hcd 0000:00:13.2: GetStatus port 2 status 003002 POWER OWNER sig=se0 CSC
> ehci_hcd 0000:00:13.2: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
> hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
> hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
> ehci_hcd 0000:00:13.2: port 3 full speed --> companion
> ehci_hcd 0000:00:13.2: GetStatus port 3 status 003801 POWER OWNER sig=j CONNECT
> hub 1-0:1.0: port 3 not reset yet, waiting 50ms
> ehci_hcd 0000:00:13.2: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
> ehci_hcd 0000:00:13.2: GetStatus port 8 status 001403 POWER sig=k CSC CONNECT
> hub 1-0:1.0: port 8, status 0501, change 0001, 480 Mb/s
> hub 1-0:1.0: debounce: port 8: total 100ms stable 100ms status 0x501
> ehci_hcd 0000:00:13.2: port 8 low speed --> companion
> ehci_hcd 0000:00:13.2: GetStatus port 8 status 003002 POWER OWNER sig=se0 CSC
> hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC PPS CCS
> hub 2-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
> hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
> usb 2-2: new full speed USB device using ohci_hcd and address 11
> ohci_hcd 0000:00:13.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC PPS PES CCS
> usb 2-2: skipped 1 descriptor after interface
> usb 2-2: default language 0x0409
> usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0
> usb 2-2: Product: HP Integrated Module
> usb 2-2: Manufacturer: Broadcom Corp
> PM: Adding info for usb:2-2
> usb 2-2: uevent
> usb 2-2: usb_probe_device
> PM: Adding info for No Bus:usbdev2.11_ep00
> usb 2-2: configuration #1 chosen from 1 choice
> usb 2-2: adding 2-2:1.0 (config #1, interface 0)
> PM: Adding info for usb:2-2:1.0
> usb 2-2:1.0: uevent
> hci_usb 2-2:1.0: usb_probe_interface
> hci_usb 2-2:1.0: usb_probe_interface - got id
> PM: Adding info for No Bus:hci0
> PM: Adding info for No Bus:usbdev2.11_ep81
> PM: Adding info for No Bus:usbdev2.11_ep82
> PM: Adding info for No Bus:usbdev2.11_ep02
> usb 2-2: adding 2-2:1.1 (config #1, interface 1)
> PM: Adding info for usb:2-2:1.1
> usb 2-2:1.1: uevent
> PM: Adding info for No Bus:usbdev2.11_ep83
> PM: Adding info for No Bus:usbdev2.11_ep03
> usb 2-2: adding 2-2:1.2 (config #1, interface 2)
> PM: Adding info for usb:2-2:1.2
> usb 2-2:1.2: uevent
> hci_usb 2-2:1.2: usb_probe_interface
> hci_usb 2-2:1.2: usb_probe_interface - got id
> PM: Adding info for No Bus:usbdev2.11_ep84
> PM: Adding info for No Bus:usbdev2.11_ep04
> usb 2-2: adding 2-2:1.3 (config #1, interface 3)
> PM: Adding info for usb:2-2:1.3
> usb 2-2:1.3: uevent
> hci_usb 2-2:1.3: usb_probe_interface
> hci_usb 2-2:1.3: usb_probe_interface - got id
> PM: Adding info for No Bus:usbdev2.11
> drivers/usb/core/inode.c: creating file '011'
> hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0012
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS
> hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
> hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
> usb 3-1: new full speed USB device using ohci_hcd and address 20
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS
> usb 3-1: ep0 maxpacket = 8
> usb 3-1: default language 0x0409
> usb 3-1: new device strings: Mfr=0, Product=1, SerialNumber=0
> usb 3-1: Product: Fingerprint Sensor
> PM: Adding info for usb:3-1
> usb 3-1: uevent
> usb 3-1: usb_probe_device
> PM: Adding info for No Bus:usbdev3.20_ep00
> usb 3-1: configuration #1 chosen from 1 choice
> usb 3-1: adding 3-1:1.0 (config #1, interface 0)
> PM: Adding info for usb:3-1:1.0
> usb 3-1:1.0: uevent
> PM: Adding info for No Bus:usbdev3.20_ep81
> PM: Adding info for No Bus:usbdev3.20_ep02
> PM: Adding info for No Bus:usbdev3.20
> drivers/usb/core/inode.c: creating file '020'
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00010301 CSC LSDA PPS CCS
> hub 3-0:1.0: port 4, status 0301, change 0001, 1.5 Mb/s
> hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x301
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00100303 PRSC LSDA PPS PES CCS
> usb 3-4: new low speed USB device using ohci_hcd and address 21
> ohci_hcd 0000:00:13.1: GetStatus roothub.portstatus [3] = 0x00100303 PRSC LSDA PPS PES CCS
> usb 3-4: skipped 1 descriptor after interface
> usb 3-4: default language 0x0409
> usb 3-4: new device strings: Mfr=1, Product=2, SerialNumber=0
> usb 3-4: Product: USB Receiver
> usb 3-4: Manufacturer: Logitech
> PM: Adding info for usb:3-4
> usb 3-4: uevent
> usb 3-4: usb_probe_device
> PM: Adding info for No Bus:usbdev3.21_ep00
> usb 3-4: configuration #1 chosen from 1 choice
> usb 3-4: adding 3-4:1.0 (config #1, interface 0)
> PM: Adding info for usb:3-4:1.0
> usb 3-4:1.0: uevent
> usbhid 3-4:1.0: usb_probe_interface
> usbhid 3-4:1.0: usb_probe_interface - got id
>   INPUT[INPUT]
>     Field(0)
>       Physical(GenericDesktop.Pointer)
>       Usage(8)
>         Button.0001
>         Button.0002
>         Button.0003
>         Button.0004
>         Button.0005
>         Button.0006
>         Button.0007
>         Button.0008
>       Logical Minimum(0)
>       Logical Maximum(1)
>       Report Size(1)
>       Report Count(8)
>       Report Offset(0)
>       Flags( Variable Absolute )
>     Field(1)
>       Physical(GenericDesktop.Pointer)
>       Usage(3)
>         GenericDesktop.X
>         GenericDesktop.Y
>         GenericDesktop.Wheel
>       Logical Minimum(-127)
>       Logical Maximum(127)
>       Report Size(8)
>       Report Count(3)
>       Report Offset(8)
>       Flags( Variable Relative )
>     Field(2)
>       Physical(GenericDesktop.Pointer)
>       Usage(1)
>         Consumer.HorizontalWheel
>       Logical Minimum(-127)
>       Logical Maximum(127)
>       Report Size(8)
>       Report Count(1)
>       Report Offset(32)
>       Flags( Variable Relative )
>     Field(3)
>       Usage(8)
>         LED.GenericIndicator
>         LED.GenericIndicator
>         LED.GenericIndicator
>         LED.GenericIndicator
>         LED.GenericIndicator
>         LED.GenericIndicator
>         LED.GenericIndicator
>         LED.GenericIndicator
>       Logical Minimum(0)
>       Logical Maximum(1)
>       Report Size(1)
>       Report Count(8)
>       Report Offset(40)
>       Flags( Variable Absolute )
>     Field(4)
>       Usage(8)
>         Button.0009
>         Button.000a
>         Button.000b
>         Button.000c
>         Button.000d
>         Button.000e
>         Button.000f
>         Button.0010
>       Logical Minimum(0)
>       Logical Maximum(1)
>       Report Size(1)
>       Report Count(8)
>       Report Offset(48)
>       Flags( Variable Absolute )
>   FEATURE[FEATURE]
>     Field(0)
>       Usage(1)
>         GenericDesktop.MotionWakeup
>       Logical Minimum(0)
>       Logical Maximum(1)
>       Report Size(1)
>       Report Count(1)
>       Report Offset(0)
>       Flags( Variable Absolute NoPrefferedState )
> Mapping: Button.0001 ---> Key.LeftBtn
> Mapping: Button.0002 ---> Key.RightBtn
> Mapping: Button.0003 ---> Key.MiddleBtn
> Mapping: Button.0004 ---> Key.SideBtn
> Mapping: Button.0005 ---> Key.ExtraBtn
> Mapping: Button.0006 ---> Key.ForwardBtn
> Mapping: Button.0007 ---> Key.BackBtn
> Mapping: Button.0008 ---> Key.TaskBtn
> Mapping: GenericDesktop.X ---> Relative.X
> Mapping: GenericDesktop.Y ---> Relative.Y
> Mapping: GenericDesktop.Wheel ---> Relative.Wheel
> Mapping: Consumer.HorizontalWheel ---> Relative.HWheel
> Mapping: LED.GenericIndicator ---> LED.Misc
> Mapping: LED.GenericIndicator ---> LED.?
> Mapping: LED.GenericIndicator ---> LED.?
> Mapping: LED.GenericIndicator ---> LED.?
> Mapping: LED.GenericIndicator ---> LED.?
> Mapping: LED.GenericIndicator ---> LED.?
> Mapping: LED.GenericIndicator ---> LED.?
> Mapping: LED.GenericIndicator ---> LED.?
> Mapping: Button.0009 ---> Key.?
> Mapping: Button.000a ---> Key.?
> Mapping: Button.000b ---> Key.?
> Mapping: Button.000c ---> Key.?
> Mapping: Button.000d ---> Key.?
> Mapping: Button.000e ---> Key.?
> Mapping: Button.000f ---> Key.?
> Mapping: Button.0010 ---> Key.?
> input: Logitech USB Receiver as /class/input/input16
> hid-pidff: starting pid init
> hid-pidff: not a PID device, no output report
> input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-4
> PM: Adding info for No Bus:usbdev3.21_ep81
> PM: Adding info for No Bus:usbdev3.21
> drivers/usb/core/inode.c: creating file '021'
> hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0100
> hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0004
> hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0002
> usb 3-1: usb auto-suspend
> SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
> hub 1-0:1.0: hub_suspend
> usb usb1: usb auto-suspend
> SoftMAC: Scanning finished: scanned 14 channels starting with channel 1
> PM: Removing info for No Bus:hw_random
> bcm43xx: Radio turned off
> bcm43xx: DMA-32 0x0200 (RX) max used slots: 0/64
> bcm43xx: DMA-32 0x02A0 (TX) max used slots: 0/512
> bcm43xx: DMA-32 0x0280 (TX) max used slots: 0/512
> bcm43xx: DMA-32 0x0260 (TX) max used slots: 0/512
> bcm43xx: DMA-32 0x0240 (TX) max used slots: 0/512
> bcm43xx: DMA-32 0x0220 (TX) max used slots: 56/512
> bcm43xx: DMA-32 0x0200 (TX) max used slots: 0/512
> PM: Adding info for No Bus:0000:30:00.0
> PM: Removing info for No Bus:0000:30:00.0
> PM: Adding info for No Bus:0000:30:00.0
> PM: Removing info for No Bus:0000:30:00.0
> PM: Adding info for No Bus:0000:30:00.0
> PM: Removing info for No Bus:0000:30:00.0
> PM: Adding info for No Bus:0000:30:00.0
> PM: Removing info for No Bus:0000:30:00.0
> bcm43xx: IRQ_READY timeout
> bcm43xx: core_up for active 802.11 core failed (-19)

I never tried suspend to disk with the driver.
Larry, an idea why the microcode doesn't respond?

-- 
Greetings Michael.