From: Michael Buesch <mb@bu3sch.de>
To: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Subject: Crash in cfg80211
Date: Tue, 6 Mar 2007 19:07:19 +0100 [thread overview]
Message-ID: <200703061907.19929.mb@bu3sch.de> (raw)
I did some stresstesting on the code in my tree.
The testscript loaded bcm43xx-mac80211, started wpa_supplicant,
rmmod while wpa_supplicant was running, in a loop.
It crashed.
Complete dmesg follows. I'm not exactly sure what happens,
but it seems cfg80211 related. The tasklet fix I sent earlier was applied.
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=30, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 2/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=30, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 1/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 2/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 8/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=31, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
sta0: deauthenticate(reason=3)
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
sta0: starting scan
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 2/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 2/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
ssb: Sonics Silicon Backplane found on PCI device 0000:06:00.0
bcm43xx_mac80211: Broadcom 4306 WLAN found
bcm43xx_mac80211: Radio turned off
wmaster0: Selected rate control algorithm 'simple'
bcm43xx_mac80211: Adding Interface type 2
bcm43xx_mac80211: Found PHY: Analog 2, Type 2, Revision 2
bcm43xx_mac80211: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
bcm43xx_mac80211: Loading firmware version 316.1 (2005-09-13 21:08:28)
bcm43xx_mac80211: Radio turned on
bcm43xx_mac80211: Radio enabled by hardware
bcm43xx_mac80211: !WARNING! Idle-TSSI phy->cur_idle_tssi measuring failed. (cur=30, tgt=62). Disabling TX power adjustment.
bcm43xx_mac80211: Chip initialized
bcm43xx_mac80211: 30-bit DMA initialized
bcm43xx_mac80211: Wireless interface started
wmaster0: Does not support passive scan, disabled
sta0: starting scan
sta0: scan completed
sta0: Initial auth_alg=0
sta0: authenticate with AP 00:12:17:d4:95:e1
sta0: RX authentication from 00:12:17:d4:95:e1 (alg=0 transaction=2 status=0)
sta0: authenticated
sta0: associate with AP 00:12:17:d4:95:e1
sta0: RX AssocResp from 00:12:17:d4:95:e1 (capab=0x411 status=0 aid=1)
sta0: associated
bcm43xx_mac80211: Using hardware based encryption for keyidx: 0, mac: 00:12:17:d4:95:e1
bcm43xx_mac80211: Using hardware based encryption for keyidx: 1, mac: ff:ff:ff:ff:ff:ff
bcm43xx_mac80211: Removing Interface type 2
bcm43xx_mac80211: Wireless interface stopped
bcm43xx_mac80211: DMA-32 0x0200 (RX) max used slots: 3/64
bcm43xx_mac80211: DMA-32 0x02A0 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0280 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0260 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0240 (TX) max used slots: 0/128
bcm43xx_mac80211: DMA-32 0x0220 (TX) max used slots: 6/128
bcm43xx_mac80211: DMA-32 0x0200 (TX) max used slots: 0/128
bcm43xx_mac80211: Radio turned off
bcm43xx_mac80211: Radio turned off
BUG: unable to handle kernel paging request at virtual address 00100104
printing eip:
c89680c7
*pde = 00000000
Oops: 0002 [#1]
PREEMPT
Modules linked in: bcm43xx_mac80211 aes af_packet apm savage drm parport_pc lp parport arc4 ecb blkcipher rc80211_simple tsdev ssb mac80211 psmouse serio_raw cfg80211 uhci_hcd usbcore snd_ymfpci gameport snd_ac97_codec ac97_bus intel_agp agpgart donauboe irda crc_ccitt snd_pcm_oss pcspkr snd_mixer_oss snd_pcm snd_opl3_lib snd_timer snd_hwdep snd_page_alloc snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore evdev i2c_piix4 i2c_core
CPU: 0
EIP: 0060:[<c89680c7>] Not tainted VLI
EFLAGS: 00210296 (2.6.21-rc1-bwldev #4)
EIP is at cfg80211_netdev_notifier_call+0xa7/0xe0 [cfg80211]
eax: c1e6d388 ebx: c5a0801c ecx: 00100100 edx: 00200200
esi: c1e6d000 edi: c1e6d000 ebp: 00000006 esp: c22b1d0c
ds: 007b es: 007b fs: 00d8 gs: 0033 ss: 0068
Process wpa_supplicant (pid: 7489, ti=c22b1000 task=c6038070 task.ti=c22b1000)
Stack: c896c1b4 c896c1b4 c8b2cb20 c1e6d000 c01255a5 c1e6d000 0000710b 0000710b
c22b1d44 c029d476 c496cb20 c02a40a0 c02afba7 c1124e54 c4c90964 c5786164
c1124e00 00000025 c22b1f40 c74c1200 c02a4057 00000000 c1124e00 00000025
Call Trace:
[<c01255a5>] notifier_call_chain+0x25/0x40
[<c029d476>] netdev_run_todo+0x196/0x280
[<c02a40a0>] rtnetlink_rcv_msg+0x0/0x240
[<c02afba7>] netlink_run_queue+0xe7/0x120
[<c02a4057>] rtnetlink_rcv+0x37/0x50
[<c02b00d2>] netlink_data_ready+0x12/0x50
[<c02aec91>] netlink_sendskb+0x21/0x40
[<c02affd6>] netlink_sendmsg+0x1d6/0x2c0
[<c029193f>] sock_sendmsg+0xbf/0xf0
[<c012bec0>] autoremove_wake_function+0x0/0x50
[<c012bec0>] autoremove_wake_function+0x0/0x50
[<c01679dd>] core_sys_select+0x24d/0x2f0
[<c0291d1f>] sys_sendto+0x12f/0x180
[<c029241f>] move_addr_to_user+0x5f/0x70
[<c0292785>] sys_recvfrom+0x125/0x180
[<c0141547>] __alloc_pages+0x57/0x2f0
[<c013f1e8>] filemap_nopage+0x2a8/0x360
[<c0291da3>] sys_send+0x33/0x40
[<c0292cd2>] sys_socketcall+0x142/0x280
[<c0104080>] sysenter_past_esp+0x5d/0x81
[<c0340000>] wireless_seq_show+0x0/0x190
=======================
Code: 5e 5f c3 83 eb 24 89 d8 e8 c7 a7 9d f7 8d 86 38 02 00 00 ba 1c a8 96 c8 e8 57 ca 82 f7 8b 86 bc 00 00 00 83 c0 3c 8b 50 04 8b 08 <89> 51 04 89 0a c7 40 04 00 02 20 00 c7 00 00 01 10 00 89 d8 e8
EIP: [<c89680c7>] cfg80211_netdev_notifier_call+0xa7/0xe0 [cfg80211] SS:ESP 0068:c22b1d0c
--
Greetings Michael.
next reply other threads:[~2007-03-06 18:08 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-03-06 18:07 Michael Buesch [this message]
2007-03-07 17:51 ` Crash in cfg80211 Johannes Berg
2007-03-08 1:19 ` [PATCH] make netdev unregister notifier idempotent Johannes Berg
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200703061907.19929.mb@bu3sch.de \
--to=mb@bu3sch.de \
--cc=johannes@sipsolutions.net \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.