From: Neil Schemenauer <nas@arctrix.com>
To: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>,
linux-kernel <linux-kernel@vger.kernel.org>,
linux-ide@vger.kernel.org, Allen Martin <AMartin@nvidia.com>,
B.Steinbrink@gmx.de
Subject: Re: sata_nv ADMA controller lockup investigation
Date: Tue, 20 Mar 2007 16:01:32 -0600 [thread overview]
Message-ID: <20070320220132.GA10984@python.ca> (raw)
In-Reply-To: <45D5389E.70300@shaw.ca>
Not sure if this helps. I'm getting this reset with 2.6.21-rc4.
After the reset the controller seems to work again.
sata_nv 0000:00:07.0: version 3.3
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:07.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0xffffc2000001e480 ctl 0xffffc2000001e4a0 bmdma 0x000000000001cc00 irq 22
ata2: SATA max UDMA/133 cmd 0xffffc2000001e580 ctl 0xffffc2000001e5a0 bmdma 0x000000000001cc08 irq 22
scsi0 : sata_nv
ata1: SATA link down (SStatus 0 SControl 300)
scsi1 : sata_nv
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: Maxtor 6V300F0, VA111630, max UDMA/133
ata2.00: 586114704 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA Maxtor 6V300F0 VA11 PQ: 0 ANSI: 5
ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 >
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg0 type 0
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:08.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0xffffc20000020480 ctl 0xffffc200000204a0 bmdma 0x000000000001b800 irq 21
ata4: SATA max UDMA/133 cmd 0xffffc20000020580 ctl 0xffffc200000205a0 bmdma 0x000000000001b808 irq 21
scsi2 : sata_nv
ata3: SATA link down (SStatus 0 SControl 300)
scsi3 : sata_nv
ata4: SATA link down (SStatus 0 SControl 300)
pata_amd 0000:00:06.0: version 0.2.8
PCI: Setting latency timer of device 0000:00:06.0 to 64
ata5: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x000000000001e000 irq 14
ata6: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x000000000001e008 irq 15
scsi4 : pata_amd
ata5.00: ATAPI, max UDMA/33
ata5.01: ATAPI, max MWDMA2
ata5.00: configured for UDMA/33
ata5.01: configured for MWDMA2
scsi5 : pata_amd
ATA: abnormal status 0x8 on port 0x0000000000010177
scsi 4:0:0:0: CD-ROM PLEXTOR DVDR PX-504A 1.02 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
sr 4:0:0:0: Attached scsi generic sg1 type 5
scsi 4:0:1:0: CD-ROM COMPAQ SC-140S SE04 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 1x/40x cd/rw xa/form2 cdda tray
sr 4:0:1:0: Attached scsi CD-ROM sr1
sr 4:0:1:0: Attached scsi generic sg2 type 5
[...]
ata2: EH in ADMA mode, notifier 0x0 notifier_error 0x0 gen_ctl 0x1501000 status 0x400 next cpb count 0x0 next cpb idx 0x0
ata2: CPB 1: ctl_flags 0x1f, resp_flags 0x2
ata2: timeout waiting for ADMA IDLE, stat=0x400
ata2: timeout waiting for ADMA LEGACY, stat=0x400
ata2.00: exception Emask 0x0 SAct 0x2 SErr 0x0 action 0x2 frozen
ata2.00: cmd 61/00:08:72:44:22/02:00:21:00:00/40 tag 1 cdb 0x0 data 262144 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata2: soft resetting port
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: configured for UDMA/133
ata2: EH complete
SCSI device sda: 586114704 512-byte hdwr sectors (300091 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
$ lspci
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2)
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3)
00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2)
00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2)
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3)
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)
01:0d.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 15)
05:00.0 VGA compatible controller: ATI Technologies Inc R430 [Radeon X800 XL] (PCIe)
05:00.1 Display controller: ATI Technologies Inc R430 [Radeon X800 XL] (PCIe) Secondary
next prev parent reply other threads:[~2007-03-20 22:08 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-02-15 4:30 sata_nv ADMA controller lockup investigation Robert Hancock
2007-02-15 10:46 ` Jeff Garzik
2007-02-16 4:52 ` Robert Hancock
2007-03-20 22:01 ` Neil Schemenauer [this message]
2007-03-20 23:24 ` Robert Hancock
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070320220132.GA10984@python.ca \
--to=nas@arctrix.com \
--cc=AMartin@nvidia.com \
--cc=B.Steinbrink@gmx.de \
--cc=hancockr@shaw.ca \
--cc=jeff@garzik.org \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.