From: Dominique Michel <dominique.michel@citycable.ch>
To: linux-acpi@vger.kernel.org, acpi4asus-user@lists.sourceforge.net
Subject: system freeze with acpi
Date: Sat, 31 Mar 2007 12:15:51 +0200 [thread overview]
Message-ID: <20070331121551.2b9c5dce@localhost> (raw)
Hi,
My whole system freeze from time to time when using acpi. I don't get this
problem without acpi. My motherboard is an asus P4S8X
# cat /proc/version
Linux version 2.6.20-rt8 (root@localhost) (gcc version 4.1.1 (Gentoo 4.1.1-r3))
#1 SMP PREEMPT Fri Mar 30 23:15:59 CEST 2007
lspci -vvv:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 645xx (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8086
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- Latency: 32
Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [c0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64-
64bit- FW- Rate=<none>
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge
(AGP) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF-
FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency:
64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e7000000-e7ffffff
Prefetchable memory behind bridge: ef700000-febfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset-
FastB2B-
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS963 [MuTIOL Media IO]
(rev 04) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0
00:02.1 SMBus: Silicon Integrated Systems [SiS] SiS961/2 SMBus Controller
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin B routed
to IRQ 0 Region 4: I/O ports at e600 [size=32]
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (prog-if 80
[Master]) Subsystem: ASUSTeK Computer Inc. Unknown device 8087
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 128
Interrupt: pin ? routed to IRQ 16
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3,
non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170
(32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at
00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at
b400 [size=16]
00:02.7 Multimedia audio controller: Silicon Integrated Systems [SiS] AC'97
Sound Controller (rev a0) Subsystem: ASUSTeK Computer Inc. Unknown device 8096
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (13000ns
min, 2750ns max) Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at a400 [size=256]
Region 1: I/O ports at a000 [size=128]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=55mA
PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller
(rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Unknown device
8087 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns
max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 20
Region 0: Memory at e6800000 (32-bit, non-prefetchable) [size=4K]
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller
(rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Unknown device
8087 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns
max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 17
Region 0: Memory at e6000000 (32-bit, non-prefetchable) [size=4K]
00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller
(rev 0f) (prog-if 10 [OHCI]) Subsystem: ASUSTeK Computer Inc. Unknown device
8087 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns
max), Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 18
Region 0: Memory at e5800000 (32-bit, non-prefetchable) [size=4K]
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
(prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. Unknown device 8087
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (20000ns max)
Interrupt: pin D routed to IRQ 21
Region 0: Memory at e5000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast
Ethernet (rev 91) Subsystem: ASUSTeK Computer Inc. Unknown device 80a7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (13000ns
min, 2750ns max) Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at 9800 [size=256]
Region 1: Memory at e4800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at ef6e0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04)
Subsystem: Creative Labs SB0240 Audigy 2 Platinum 6.1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min,
5000ns max) Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 9400 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.1 Input device controller: Creative Labs SB Audigy Game Port (rev 04)
Subsystem: Creative Labs SB Audigy MIDI/Game Port
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32
Region 0: I/O ports at 9000 [size=8]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04)
(prog-if 10 [OHCI]) Subsystem: Creative Labs SB Audigy FireWire Port
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (500ns min,
1000ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 19
Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at e3800000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:0d.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture
(rev 11) Subsystem: Scion Corporation Unknown device 0012
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (4000ns min,
10000ns max) Interrupt: pin A routed to IRQ 22
Region 0: Memory at ee800000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev
11) Subsystem: Scion Corporation Unknown device 0012
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (1000ns min,
63750ns max) Interrupt: pin A routed to IRQ 10
Region 0: Memory at ee000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti 4200]
(rev a3) (prog-if 00 [VGA]) Subsystem: Micro-Star International Co., Ltd.
Unknown device 8700 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 (1250ns min,
250ns max) Interrupt: pin A routed to IRQ 16
Region 0: Memory at e7000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 2: Memory at ef800000 (32-bit, prefetchable) [size=512K]
Expansion ROM at ef7e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64-
64bit- FW- Rate=<none>
# cat /proc/interrupts
CPU0
0: 283 IO-APIC-edge timer
1: 691 IO-APIC-edge i8042
6: 5 IO-APIC-edge floppy
7: 0 IO-APIC-edge parport0
8: 2 IO-APIC-edge rtc
12: 4 IO-APIC-edge i8042
14: 20344 IO-APIC-edge ide0
15: 24156 IO-APIC-edge ide1
17: 108 IO-APIC-fasteoi ohci_hcd:usb2
18: 1 IO-APIC-fasteoi ohci_hcd:usb3
19: 1043 IO-APIC-fasteoi ohci1394, eth0
20: 23230 IO-APIC-fasteoi acpi, ohci_hcd:usb1
21: 781 IO-APIC-fasteoi ehci_hcd:usb4
22: 4 IO-APIC-fasteoi bttv0
23: 1943588 IO-APIC-fasteoi EMU10K1
NMI: 0
LOC: 548999
ERR: 0
MIS: 0
Is it normal at acpi use the same IRQ as ohci_hcd:usb1? I don't think so, but I
can be wrong.
# cat .config|grep ACPI
# Power management options (ACPI, APM)
# ACPI (Advanced Configuration and Power Interface) Support
CONFIG_ACPI=y
# CONFIG_ACPI_AC is not set
# CONFIG_ACPI_BATTERY is not set
# CONFIG_ACPI_BUTTON is not set
# CONFIG_ACPI_VIDEO is not set
# CONFIG_ACPI_HOTKEY is not set
# CONFIG_ACPI_FAN is not set
# CONFIG_ACPI_DOCK is not set
# CONFIG_ACPI_PROCESSOR is not set
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_IBM is not set
# CONFIG_ACPI_TOSHIBA is not set
CONFIG_ACPI_BLACKLIST_YEAR=2001
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_ACPI_CONTAINER is not set
# CONFIG_ACPI_SBS is not set
CONFIG_PNPACPI=y
# dmesg|grep ACPI
BIOS-e820: 000000005fffc000 - 000000005ffff000 (ACPI data)
BIOS-e820: 000000005ffff000 - 0000000060000000 (ACPI NVS)
ACPI: RSDP (v000 ASUS ) @ 0x000f5810
ACPI: RSDT (v001 ASUS P4S8X 0x42302e31 MSFT 0x31313031) @ 0x5fffc000
ACPI: FADT (v001 ASUS P4S8X 0x42302e31 MSFT 0x31313031) @ 0x5fffc0c0
ACPI: BOOT (v001 ASUS P4S8X 0x42302e31 MSFT 0x31313031) @ 0x5fffc030
ACPI: MADT (v001 ASUS P4S8X 0x42302e31 MSFT 0x31313031) @ 0x5fffc058
ACPI: DSDT (v001 ASUS P4S8X 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: Core revision 20060707
ACPI: bus type pci registered
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
pnp: PnP ACPI init
pnp: PnP ACPI: found 16 devices
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 17
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 18
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 21
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 17 (level, low) -> IRQ 22
ACPI: PCI Interrupt 0000:00:0a.2[B] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 23
It is with the last bios revison, 1005.
With a 2.6.19.1-rt15 that have antother configuration and work fine, I get
when running it with pci=noacpi:
# cat /proc/interrupts
CPU0
0: 228789 XT-PIC-XT timer
1: 229 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
5: 148178 XT-PIC-XT EMU10K1
6: 5 XT-PIC-XT floppy
7: 1 XT-PIC-XT parport0
8: 2 XT-PIC-XT rtc
9: 4641 XT-PIC-XT acpi, ohci_hcd:usb1, ehci_hcd:usb2,
ohci1394, ohci_hcd:usb3, ohci_hcd:usb4, eth0
10: 4 XT-PIC-XT bttv0
11: 10019 XT-PIC-XT nvidia
12: 4 XT-PIC-XT i8042
14: 19935 XT-PIC-XT ide0
15: 3605 XT-PIC-XT ide1
NMI: 729962
LOC: 228630
ERR: 0
MIS: 0
My problem is at I really want to use CONFIG_X86_PM_TIMER in the ACPI config.
Cheers,
Dominique
next reply other threads:[~2007-03-31 12:21 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-03-31 10:15 Dominique Michel [this message]
2007-04-03 2:12 ` system freeze with acpi Len Brown
2007-04-03 23:19 ` Sergio Monteiro Basto
2007-04-04 6:12 ` Dominique Michel
2007-04-04 7:40 ` Dominique Michel
-- strict thread matches above, loose matches on Subject: below --
2007-04-06 17:31 Dominique Michel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070331121551.2b9c5dce@localhost \
--to=dominique.michel@citycable.ch \
--cc=acpi4asus-user@lists.sourceforge.net \
--cc=linux-acpi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.