From: Andrew Morton <akpm@linux-foundation.org>
To: Torsten Kaiser <just.for.lkml@googlemail.com>
Cc: linux-kernel@vger.kernel.org, linux-ide@vger.kernel.org
Subject: Re: 2.6.23-rc4-mm1
Date: Sat, 1 Sep 2007 09:16:42 -0700 [thread overview]
Message-ID: <20070901091642.aad85849.akpm@linux-foundation.org> (raw)
In-Reply-To: <64bb37e0709010907x5a73f9dbof8e5b2c92425452e@mail.gmail.com>
> On Sat, 1 Sep 2007 18:07:48 +0200 "Torsten Kaiser" <just.for.lkml@googlemail.com> wrote:
> On 9/1/07, Andrew Morton <akpm@linux-foundation.org> wrote:
> >
> > ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.23-rc4/2.6.23-rc4-mm1/
>
> The good:
> > +hpet-force-enable-on-vt8235-37-chipsets.patch
> > +hpet-force-enable-on-vt8235-37-chipsets-fix.patch
>
> Kernel 2.6.23-rc4-mm1 works on one of my systems with:
> ...
> It now has a working HPET.
Great, thanks.
> The bad:
> sata_sil24 and/or libata are broken.
yup. Let's cc linux-ide.
> On my second system (MCP55 + SiI 3132) I see this:
> [ 3.890000] scsi0 : sata_sil24
> [ 3.900000] scsi1 : sata_sil24
> [ 3.900000] ata1: SATA max UDMA/100 host m128@0xefeffc00 port
> 0xefef8000 irq 16
> [ 3.920000] ata2: SATA max UDMA/100 host m128@0xefeffc00 port
> 0xefefa000 irq 16
> [ 4.300000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 4.360000] ata1.00: ATA-7: MAXTOR STM3320820AS, 3.AAE, max UDMA/133
> [ 4.370000] ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 4.430000] ata1.00: configured for UDMA/100
> [ 4.500000] ieee1394: Node added: ID:BUS[0-00:1023] GUID[0010dc00005cc354]
> [ 4.500000] ieee1394: Host added: ID:BUS[0-01:1023] GUID[0011d80000c4c261]
> [ 4.790000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [ 4.850000] ata2.00: ATA-7: MAXTOR STM3320820AS, 3.AAE, max UDMA/133
> [ 4.860000] ata2.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32)
> [ 4.920000] ata2.00: configured for UDMA/100
> [ 4.930000] scsi 0:0:0:0: Direct-Access ATA MAXTOR
> STM332082 3.AA PQ: 0 ANSI: 5
> [ 4.960000] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> [ 4.980000] sd 0:0:0:0: [sda] Write Protect is off
> [ 4.990000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 4.990000] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 5.020000] sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
> [ 5.040000] sd 0:0:0:0: [sda] Write Protect is off
> [ 5.050000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
> [ 5.050000] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 5.080000] sda: sda1 sda2
> [ 5.110000] sd 0:0:0:0: [sda] Attached SCSI disk
> [ 5.120000] scsi 1:0:0:0: Direct-Access ATA MAXTOR
> STM332082 3.AA PQ: 0 ANSI: 5
> [ 5.140000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
> [ 5.170000] sd 1:0:0:0: [sdb] Write Protect is off
> [ 5.180000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> [ 5.180000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 5.210000] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
> [ 5.230000] sd 1:0:0:0: [sdb] Write Protect is off
> [ 5.240000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
> [ 5.240000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache:
> enabled, doesn't support DPO or FUA
> [ 5.270000] sdb: sdb1 sdb2
> [ 5.300000] sd 1:0:0:0: [sdb] Attached SCSI disk
> [snip]
> [ 12.120000] Freeing unused kernel memory: 340k freed
> [ 33.210000] md: Autodetecting RAID arrays.
> [ 33.300000] md: Scanned 5 and added 5 devices.
> [ 33.300000] md: autorun ...
> [ 33.300000] md: considering sdc2 ...
> [ 33.300000] md: adding sdc2 ...
> [ 33.300000] md: adding sdb2 ...
> [ 33.300000] md: sdb1 has different UUID to sdc2
> [ 33.300000] md: adding sda2 ...
> [ 33.300000] md: sda1 has different UUID to sdc2
> [ 33.300000] md: created md1
> [ 33.300000] md: bind<sda2>
> [ 33.300000] md: bind<sdb2>
> [ 33.300000] md: bind<sdc2>
> [ 33.300000] md: running: <sdc2><sdb2><sda2>
> [ 33.310000] raid5: device sdc2 operational as raid disk 2
> [ 33.310000] raid5: device sdb2 operational as raid disk 1
> [ 33.310000] raid5: device sda2 operational as raid disk 0
> [ 33.310000] raid5: allocated 3224kB for md1
> [ 33.310000] raid5: raid level 5 set md1 active with 3 out of 3
> devices, algorithm 2
> [ 33.310000] RAID5 conf printout:
> [ 33.310000] --- rd:3 wd:3
> [ 33.310000] disk 0, o:1, dev:sda2
> [ 33.310000] disk 1, o:1, dev:sdb2
> [ 33.310000] disk 2, o:1, dev:sdc2
> [ 33.320000] md1: bitmap initialized from disk: read 10/10 pages, set 115 bits
> [ 33.320000] created bitmap (145 pages) for device md1
> [ 63.420000] ata2.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
> [ 63.420000] ata2.00: cmd 61/08:00:09:d6:42/00:00:25:00:00/40 tag 0
> cdb 0x0 data 4096 out
> [ 63.420000] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask
> 0x4 (timeout)
> [ 63.420000] ata2.00: status: {DRDY }
> [ 63.420000] ata2: hard resetting link
> [ 65.720000] ata2: softreset failed (port not ready)
> [ 65.720000] ata2: reset failed (errno=-5), retrying in 8 secs
> [ 73.420000] ata2: hard resetting link
> [ 75.720000] ata2: softreset failed (port not ready)
> [ 75.720000] ata2: reset failed (errno=-5), retrying in 8 secs
> [ 83.420000] ata2: hard resetting link
> [ 85.720000] ata2: softreset failed (port not ready)
> [ 85.720000] ata2: reset failed (errno=-5), retrying in 33 secs
> [ 118.420000] ata2: limiting SATA link speed to 1.5 Gbps
> [ 118.420000] ata2: hard resetting link
> [ 120.720000] ata2: softreset failed (port not ready)
> [ 120.720000] ata2: reset failed, giving up
> [ 120.720000] ata2.00: disabled
> [ 120.720000] ata2: EH complete
> [ 120.720000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.720000] end_request: I/O error, dev sdb, sector 625137161
> [ 120.720000] md: super_written gets error=-5, uptodate=0
> [ 120.720000] raid5: Disk failure on sdb2, disabling device.
> Operation continuing on 2 devices
> [ 120.750000] md: considering sdb1 ...
> [ 120.750000] RAID5 conf printout:
> [ 120.750000] --- rd:3 wd:2
> [ 120.750000] md: adding sdb1 ...
> [ 120.750000] disk 0, o:1, dev:sda2
> [ 120.750000] disk 1, o:0, dev:sdb2
> [ 120.750000] disk 2, o:1, dev:sdc2
> [ 120.750000] md: adding sda1 ...
> [ 120.750000] md: created md0
> [ 120.750000] md: bind<sda1>
> [ 120.750000] md: bind<sdb1>
> [ 120.750000] md: running: <sdb1><sda1>
> [ 120.760000] raid1: raid set md0 active with 2 out of 2 mirrors
> [ 120.760000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.760000] end_request: I/O error, dev sdb, sector 19550919
> [ 120.780000] RAID5 conf printout:
> [ 120.780000] --- rd:3 wd:2
> [ 120.780000] disk 0, o:1, dev:sda2
> [ 120.780000] disk 2, o:1, dev:sdc2
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550927
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550935
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550943
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550951
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550959
> [ 120.780000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.780000] end_request: I/O error, dev sdb, sector 19550967
> [ 120.790000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.790000] end_request: I/O error, dev sdb, sector 19550975
> [ 120.790000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.790000] end_request: I/O error, dev sdb, sector 19550983
> [ 120.790000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.790000] end_request: I/O error, dev sdb, sector 19550991
> [ 120.790000] md0: bitmap initialized from disk: read 10/10 pages, set 0 bits
> [ 120.790000] created bitmap (150 pages) for device md0
> [ 120.790000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 120.790000] end_request: I/O error, dev sdb, sector 19550919
> [ 120.790000] md: super_written gets error=-5, uptodate=0
> [ 120.790000] raid1: Disk failure on sdb1, disabling device.
> [ 120.790000] Operation continuing on 1 devices
> [ 120.810000] md: ... autorun DONE.
> [ 120.810000] RAID1 conf printout:
> [ 120.810000] --- wd:1 rd:2
> [ 120.810000] disk 0, wo:0, o:1, dev:sda1
> [ 120.810000] disk 1, wo:1, o:0, dev:sdb1
> [ 120.860000] RAID1 conf printout:
> [ 120.860000] --- wd:1 rd:2
> [ 120.860000] disk 0, wo:0, o:1, dev:sda1
> [ 129.360000] Filesystem "dm-0": Disabling barriers, trial barrier write failed
> [ 129.390000] XFS mounting filesystem dm-0
> [ 129.600000] Ending clean XFS mount for filesystem: dm-0
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 625137153
> [ 132.850000] Buffer I/O error on device sdb2, logical block 75698256
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 625137153
> [ 132.850000] Buffer I/O error on device sdb2, logical block 75698256
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 625137153
> [ 132.850000] Buffer I/O error on device sdb2, logical block 75698256
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 19551105
> [ 132.850000] Buffer I/O error on device sdb2, logical block 0
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 19551113
> [ 132.850000] Buffer I/O error on device sdb2, logical block 1
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 19551105
> [ 132.850000] Buffer I/O error on device sdb2, logical block 0
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 19551105
> [ 132.850000] Buffer I/O error on device sdb2, logical block 0
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 625137337
> [ 132.850000] Buffer I/O error on device sdb2, logical block 75698279
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 625137337
> [ 132.850000] Buffer I/O error on device sdb2, logical block 75698279
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 625137337
> [ 132.850000] Buffer I/O error on device sdb2, logical block 75698279
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 625137337
> [ 132.850000] sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET
> driverbyte=DRIVER_OK,SUGGEST_OK
> [ 132.850000] end_request: I/O error, dev sdb, sector 625137337
> ...
>
> After that the system booted up fine, only running with the two of
> three RAID drives.
> (sda is on sata_sil24, sdc on sata_nv. I used the sata_nv.swncq=1 switch)
>
> The ugly:
> I wanted to verify that this was not a onetime bug and rebooted the system.
> This time md kicked sdb because it was stale and then also kicked sda
> with an error similar to the above. Which killed the RAID5 completely.
> :(
> At least I was able to resurrect it with mdadm --force.
>
> So the sata_sil24 error seems repeatable, but also not limited to one
> specific port.
>
> The system is now up again running 2.6.23-rc3-mm1 with all three drives.
>
> Torsten
next prev parent reply other threads:[~2007-09-01 16:16 UTC|newest]
Thread overview: 164+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-09-01 4:58 2.6.23-rc4-mm1 Andrew Morton
2007-09-01 6:53 ` 2.6.23-rc4-mm1 KAMEZAWA Hiroyuki
2007-09-01 6:58 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-01 8:54 ` 2.6.23-rc4-mm1 Herbert Xu
2007-09-01 21:09 ` 2.6.23-rc4-mm1 Satyam Sharma
2007-09-02 1:46 ` 2.6.23-rc4-mm1 Herbert Xu
2007-09-02 2:52 ` 2.6.23-rc4-mm1 Satyam Sharma
2007-09-02 3:59 ` 2.6.23-rc4-mm1 Herbert Xu
2007-09-01 11:55 ` 2.6.23-rc4-mm1 Kamalesh Babulal
2007-09-01 14:18 ` 2.6.23-rc4-mm1: geode fb compile error Adrian Bunk
2007-09-01 17:03 ` Satyam Sharma
2007-09-01 15:19 ` 2.6.23-rc4-mm1: two ktime_sub_ns() functions Adrian Bunk
2007-09-01 15:44 ` 2.6.23-rc4-mm1: mips compile error Adrian Bunk
2007-09-04 5:27 ` Mathieu Desnoyers
2007-09-04 10:21 ` Ralf Baechle
2007-09-01 16:07 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-01 16:16 ` Andrew Morton [this message]
2007-09-01 18:13 ` 2.6.23-rc4-mm1 OOPS in forcedeth? thunder7
2007-09-01 19:05 ` Jeff Garzik
2007-09-02 0:54 ` Satyam Sharma
2007-09-02 5:36 ` thunder7
2007-09-02 6:19 ` thunder7
2007-09-02 9:55 ` Satyam Sharma
2007-09-14 3:51 ` Andrew James Wade
2007-09-17 13:57 ` Dhaval Giani
2007-09-17 14:07 ` Denis V. Lunev
2007-09-17 21:00 ` Vlad Yasevich
2007-09-17 23:56 ` Satyam Sharma
2007-09-01 22:06 ` 2.6.23-rc4-mm1 "no CRC" MODPOST warnings Satyam Sharma
2007-09-01 22:40 ` Adrian Bunk
2007-09-01 23:15 ` Sam Ravnborg
2007-09-01 23:12 ` [PATCH -mm] softlockup-improve-debug-output.patch fix Satyam Sharma
2007-09-02 12:37 ` [PATCH -mm][resend] " Satyam Sharma
2007-09-02 12:28 ` Ingo Molnar
2007-09-06 6:52 ` [PATCH] sched: Use show_regs() to improve __schedule_bug() output Satyam Sharma
2007-10-22 12:35 ` Ingo Molnar
2007-09-03 16:36 ` [PATCH -mm][resend] softlockup-improve-debug-output.patch fix Valdis.Kletnieks
2007-09-01 23:42 ` [PATCH -mm] drivers/acpi/tables/tbutils.c: Shut up bogus uninitialized variable warning Satyam Sharma
2007-09-02 0:19 ` Adrian Bunk
2007-09-02 1:02 ` Satyam Sharma
2007-09-02 1:30 ` [PATCH -mm] net/sched/sch_cbq.c: Shut up " Satyam Sharma
2007-09-02 11:36 ` Patrick McHardy
2007-09-02 2:36 ` 2.6.23-rc4-mm1: unpingable box and NULL dereference at tcp_rto_min() Alexey Dobriyan
2007-09-02 5:02 ` Satyam Sharma
2007-09-02 20:52 ` Andrew Morton
2007-09-02 21:19 ` Alexey Dobriyan
2007-09-02 9:14 ` 2.6.23-rc4-mm1 net bitops compile error Adrian Bunk
2007-09-04 17:53 ` Jiri Slaby
2007-09-02 11:25 ` [-mm patch] IPV6 must select XFRM Adrian Bunk
2007-09-03 10:43 ` Masahide NAKAMURA
2007-09-06 10:01 ` net-26.24 broken with XFRM off Noriaki TAKAMIYA
2007-09-02 13:00 ` [PATCH -mm] drivers/char/nozomi.c: __devexit_p usage build fix Satyam Sharma
2007-09-02 19:01 ` 2.6.23-rc4-mm1: broke pata_via cable detection Laurent Riffard
2007-09-02 19:20 ` Alan Cox
2007-09-11 1:50 ` Jeff Garzik
2007-09-02 20:39 ` 2.6.23-rc4-mm1: boot failure on HPC nx6325 Rafael J. Wysocki
2007-09-03 8:36 ` Thomas Gleixner
2007-09-03 10:15 ` Rafael J. Wysocki
2007-09-03 20:51 ` Rafael J. Wysocki
2007-09-04 1:03 ` Thomas Gleixner
2007-09-03 4:30 ` 2.6.23-rc4-mm1 Randy Dunlap
2007-09-03 19:25 ` 2.6.23-rc4-mm1 Wim Van Sebroeck
2007-09-03 22:32 ` 2.6.23-rc4-mm1 Satyam Sharma
2007-09-04 21:21 ` 2.6.23-rc4-mm1 Wim Van Sebroeck
2007-09-04 17:54 ` 2.6.23-rc4-mm1 Zach Carter
2007-09-04 21:36 ` 2.6.23-rc4-mm1 Stephen Hemminger
2007-09-05 14:37 ` 2.6.23-rc4-mm1 Valdis.Kletnieks
2007-09-05 15:12 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-05 15:20 ` 2.6.23-rc4-mm1 Balbir Singh
2007-09-05 15:58 ` 2.6.23-rc4-mm1 Valdis.Kletnieks
2007-09-05 19:46 ` 2.6.23-rc4-mm1 - git-alsa.patch breaks audio on Dell Latitude D820 Valdis.Kletnieks
2007-09-05 19:54 ` Valdis.Kletnieks
2007-09-05 20:22 ` Takashi Iwai
2007-09-05 20:11 ` Takashi Iwai
2007-09-05 20:27 ` Takashi Iwai
2007-09-05 21:16 ` Valdis.Kletnieks
2007-09-05 21:39 ` Takashi Iwai
2007-09-06 14:10 ` Valdis.Kletnieks
2007-09-06 14:17 ` Takashi Iwai
2007-09-06 19:37 ` 2.6.23-rc4-mm1 myri10ge module link error on x86_64 Mathieu Desnoyers
2007-09-06 20:40 ` David Miller
2007-09-06 20:48 ` David Miller
2007-09-07 23:59 ` Jeff Garzik
2007-09-08 0:25 ` Daniel Walker
2007-10-13 22:03 ` Avuton Olrich
2007-09-09 12:22 ` 2.6.23-rc4-mm1 Mel Gorman
2007-09-14 15:12 ` ath5k driver not working on ThinkPad Robert de Rooy
2007-09-09 20:24 ` [-mm patch] alpha bitops.h must #include <asm/barrier.h> Adrian Bunk
2007-09-09 20:24 ` [-mm patch] remove ide_get_error_location() Adrian Bunk
2007-09-11 21:27 ` Bartlomiej Zolnierkiewicz
2007-09-12 5:54 ` Jens Axboe
2007-09-09 20:24 ` [-mm patch] drivers/dma/ioat_dma.c: make 3 functions static Adrian Bunk
2007-09-09 20:25 ` [-mm patch] usb/serial/ch341.c: make 4 " Adrian Bunk
2007-09-09 20:25 ` [-mm patch] make nfs_wb_page_priority() static Adrian Bunk
2007-09-09 20:25 ` [-mm patch] kernel/kexec.c: make code static Adrian Bunk
2007-09-09 20:25 ` Adrian Bunk
2007-09-10 2:55 ` Ken'ichi Ohmichi
2007-09-10 2:55 ` Ken'ichi Ohmichi
2007-09-10 12:20 ` Adrian Bunk
2007-09-10 12:20 ` Adrian Bunk
2007-09-11 5:53 ` Maneesh Soni
2007-09-11 5:53 ` Maneesh Soni
2007-09-12 7:37 ` Ken'ichi Ohmichi
2007-09-12 7:37 ` Ken'ichi Ohmichi
2007-09-09 20:25 ` [-mm patch] really unexport do_softirq Adrian Bunk
2007-09-12 13:14 ` David Miller
2007-09-09 20:25 ` [-mm patch] unexport raise_softirq_irqoff Adrian Bunk
2007-09-09 20:41 ` Christoph Hellwig
2007-09-12 13:15 ` David Miller
2007-09-09 20:25 ` [-mm patch] mm/memcontrol.c: clenups Adrian Bunk
2007-09-10 8:23 ` Balbir Singh
2007-09-10 19:58 ` Jan Engelhardt
2007-09-10 19:59 ` Jan Engelhardt
2007-09-10 21:59 ` Adrian Bunk
2007-09-11 2:41 ` Balbir Singh
2007-09-09 20:25 ` [-mm patch] net/sctp/socket.c: make 3 variables static Adrian Bunk
2007-09-10 14:05 ` [Lksctp-developers] " Neil Horman
2007-09-12 13:18 ` David Miller
2007-09-09 20:25 ` [-mm patch] make tcp_splice_data_recv() static Adrian Bunk
2007-09-12 13:21 ` David Miller
2007-09-12 17:44 ` Jens Axboe
2007-09-09 20:26 ` [-mm patch] make do_try_to_free_pages() static Adrian Bunk
2007-09-10 8:24 ` Balbir Singh
2007-09-10 17:43 ` 2.6.23-rc4-mm1 -- powerpc per_cpu__cpu_sibling_map compile failure Andy Whitcroft
2007-09-10 17:43 ` Andy Whitcroft
2007-09-10 17:49 ` 2.6.23-rc4-mm1 Andy Whitcroft
2007-09-10 18:19 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-10 18:59 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-10 19:20 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-10 19:38 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-10 19:42 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-10 20:43 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-11 8:32 ` 2.6.23-rc4-mm1 Jens Axboe
2007-09-10 19:10 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-13 17:34 ` 2.6.23-rc4-mm1 Andy Whitcroft
2007-09-15 4:16 ` 2.6.23-rc4-mm1 Paul Jackson
2007-09-15 10:52 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-17 13:28 ` 2.6.23-rc4-mm1 Jens Axboe
2007-09-17 14:32 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-18 10:18 ` 2.6.23-rc4-mm1 Jens Axboe
2007-09-18 12:25 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-18 12:51 ` 2.6.23-rc4-mm1 Jens Axboe
2007-09-10 19:31 ` 2.6.23-rc4-mm1 FUJITA Tomonori
2007-09-14 8:10 ` 2.6.23-rc4-mm1 Andy Whitcroft
2007-09-14 13:01 ` 2.6.23-rc4-mm1 Torsten Kaiser
2007-09-14 20:15 ` 2.6.23-rc4-mm1 Andrew Morton
2007-09-10 20:19 ` 2.6.23-rc4-mm1: git-block.patch broke pktcdvd Laurent Riffard
2007-09-13 22:50 ` Laurent Riffard
2007-09-13 23:05 ` Andrew Morton
2007-09-14 8:00 ` Jens Axboe
2007-09-14 8:30 ` Jens Axboe
2007-09-14 9:33 ` Jens Axboe
2007-09-14 11:06 ` Jens Axboe
2007-09-14 19:04 ` Laurent Riffard
2007-09-20 21:25 ` [PATCH] pktcdvd: don't rely on bio_init() preserving bio->bi_destructor Laurent Riffard
2007-09-21 5:19 ` Jens Axboe
-- strict thread matches above, loose matches on Subject: below --
2007-09-02 2:56 2.6.23-rc4-mm1 Mats Johannesson
2007-09-03 8:06 ` 2.6.23-rc4-mm1 Nicolas Mailhot
2007-09-04 15:20 ` 2.6.23-rc4-mm1 Alistair John Strachan
2007-09-04 15:26 ` 2.6.23-rc4-mm1 Andi Kleen
2007-09-04 16:05 ` 2.6.23-rc4-mm1 Alistair John Strachan
2007-09-06 7:25 net-26.24 broken with XFRM off Divy Le Ray
2007-09-06 8:13 ` Eric Dumazet
2007-09-06 9:50 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20070901091642.aad85849.akpm@linux-foundation.org \
--to=akpm@linux-foundation.org \
--cc=just.for.lkml@googlemail.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.