From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
To: linux-ide@vger.kernel.org
Subject: [PATCH 6/15] cmd640: fix deadlock on error handling
Date: Mon, 1 Oct 2007 23:35:14 +0200 [thread overview]
Message-ID: <200710012335.14886.bzolnier@gmail.com> (raw)
Stop abusing ide_lock lock (switch to a private locking).
Fixes same issue as fixed by Alan Cox in atiixp host driver with
commit 6c5f8cc33eb2e10b6ab788bbe259fc142a068627.
cmd640 is a bit special cause we still need to leave ide_lock for
->set_pio_mode with 'pio' argument == 8/9 (prefetch disable/enable).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
---
drivers/ide/pci/cmd640.c | 48 +++++++++++++++++++++++++++--------------------
1 file changed, 28 insertions(+), 20 deletions(-)
Index: b/drivers/ide/pci/cmd640.c
===================================================================
--- a/drivers/ide/pci/cmd640.c
+++ b/drivers/ide/pci/cmd640.c
@@ -185,6 +185,8 @@ static u8 recovery_counts[4] = {16, 16,
#endif /* CONFIG_BLK_DEV_CMD640_ENHANCED */
+static DEFINE_SPINLOCK(cmd640_lock);
+
/*
* These are initialized to point at the devices we control
*/
@@ -258,12 +260,12 @@ static u8 get_cmd640_reg_vlb (u16 reg)
static u8 get_cmd640_reg(u16 reg)
{
- u8 b;
unsigned long flags;
+ u8 b;
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave(&cmd640_lock, flags);
b = __get_cmd640_reg(reg);
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
return b;
}
@@ -271,9 +273,9 @@ static void put_cmd640_reg(u16 reg, u8 v
{
unsigned long flags;
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave(&cmd640_lock, flags);
__put_cmd640_reg(reg,val);
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
}
static int __init match_pci_cmd640_device (void)
@@ -351,7 +353,7 @@ static int __init secondary_port_respond
{
unsigned long flags;
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave(&cmd640_lock, flags);
outb_p(0x0a, 0x170 + IDE_SELECT_OFFSET); /* select drive0 */
udelay(100);
@@ -359,11 +361,11 @@ static int __init secondary_port_respond
outb_p(0x1a, 0x170 + IDE_SELECT_OFFSET); /* select drive1 */
udelay(100);
if ((inb_p(0x170 + IDE_SELECT_OFFSET) & 0x1f) != 0x1a) {
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
return 0; /* nothing responded */
}
}
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
return 1; /* success */
}
@@ -440,11 +442,11 @@ static void __init setup_device_ptrs (vo
static void set_prefetch_mode (unsigned int index, int mode)
{
ide_drive_t *drive = cmd_drives[index];
+ unsigned long flags;
int reg = prefetch_regs[index];
u8 b;
- unsigned long flags;
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave(&cmd640_lock, flags);
b = __get_cmd640_reg(reg);
if (mode) { /* want prefetch on? */
#if CMD640_PREFETCH_MASKS
@@ -460,7 +462,7 @@ static void set_prefetch_mode (unsigned
b |= prefetch_masks[index]; /* disable prefetch */
}
__put_cmd640_reg(reg, b);
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
}
/*
@@ -561,7 +563,7 @@ static void program_drive_counts (unsign
/*
* Now that everything is ready, program the new timings
*/
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave(&cmd640_lock, flags);
/*
* Program the address_setup clocks into ARTTIM reg,
* and then the active/recovery counts into the DRWTIM reg
@@ -570,7 +572,7 @@ static void program_drive_counts (unsign
setup_count |= __get_cmd640_reg(arttim_regs[index]) & 0x3f;
__put_cmd640_reg(arttim_regs[index], setup_count);
__put_cmd640_reg(drwtim_regs[index], pack_nibbles(active_count, recovery_count));
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
}
/*
@@ -630,6 +632,7 @@ static void cmd640_set_mode (unsigned in
static void cmd640_set_pio_mode(ide_drive_t *drive, const u8 pio)
{
+ unsigned long flags;
unsigned int index = 0, cycle_time;
u8 b;
@@ -652,7 +655,12 @@ static void cmd640_set_pio_mode(ide_driv
case 8: /* set prefetch off */
case 9: /* set prefetch on */
+ /*
+ * take ide_lock for drive->[no_]unmask/[no_]io_32bit
+ */
+ spin_lock_irqsave(&ide_lock, flags);
set_prefetch_mode(index, pio & 1);
+ spin_unlock_irqrestore(&ide_lock, flags);
printk("%s: %sabled cmd640 prefetch\n", drive->name, (pio & 1) ? "en" : "dis");
return;
}
@@ -670,20 +678,20 @@ static void cmd640_set_pio_mode(ide_driv
static int pci_conf1(void)
{
- u32 tmp;
unsigned long flags;
+ u32 tmp;
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave(&cmd640_lock, flags);
outb(0x01, 0xCFB);
tmp = inl(0xCF8);
outl(0x80000000, 0xCF8);
if (inl(0xCF8) == 0x80000000) {
outl(tmp, 0xCF8);
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
return 1;
}
outl(tmp, 0xCF8);
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
return 0;
}
@@ -691,15 +699,15 @@ static int pci_conf2(void)
{
unsigned long flags;
- spin_lock_irqsave(&ide_lock, flags);
+ spin_lock_irqsave(&cmd640_lock, flags);
outb(0x00, 0xCFB);
outb(0x00, 0xCF8);
outb(0x00, 0xCFA);
if (inb(0xCF8) == 0x00 && inb(0xCF8) == 0x00) {
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
return 1;
}
- spin_unlock_irqrestore(&ide_lock, flags);
+ spin_unlock_irqrestore(&cmd640_lock, flags);
return 0;
}
reply other threads:[~2007-10-01 21:39 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200710012335.14886.bzolnier@gmail.com \
--to=bzolnier@gmail.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.