All of lore.kernel.org
 help / color / mirror / Atom feed
From: Guilherme Amadio <guilherme.amadio@gmail.com>
To: linux-ide@vger.kernel.org
Subject: ata_piix: ICH7 "invalid MAP value 0" msg at boot
Date: Mon, 15 Oct 2007 15:14:44 -0200	[thread overview]
Message-ID: <20071015171444.GA9512@vaio> (raw)

 Hello,

 I have a Sony laptop SZ series and I get the message
 
 ata_piix 0000:00:1f.2: invalid MAP value 0

 even with 'quiet' in the boot command line. I think it's because of a controller
 with no disk attached, but I am a total newb, so I went to #kernelnewbies and 
 I was told to post this here. The code that prints the message is here
 drivers/ata/ata_piix.c +973. 
 
 I'm using this kernel:
 Linux vaio 2.6.22-gentoo-r8 #1 SMP PREEMPT Sun Sep 30 13:19:56 BRT 2007
 i686 Genuine Intel(R) CPU T2400 @ 1.83GHz GenuineIntel GNU/Linux

 Below are the outputs that may be relevant for tracing the problem.
 If anything else is needed, I can provide, but please CC me, because I'm
 not subscribed to the list.

 Guilherme 

-- 
 dmesg:
 
 ata_piix 0000:00:1f.2: version 2.11
 ata_piix 0000:00:1f.2: MAP [ P0 P2 XX XX ]
 ata_piix 0000:00:1f.2: invalid MAP value 0
 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 22 (level, low) -> IRQ 21
 PCI: Setting latency timer of device 0000:00:1f.2 to 64
 scsi0 : ata_piix
 scsi1 : ata_piix
 ata1: SATA max UDMA/133 cmd 0x000118d0 ctl 0x000118c6 bmdma 0x000118b0 irq 21
 ata2: SATA max UDMA/133 cmd 0x000118c8 ctl 0x000118c2 bmdma 0x000118b8 irq 21
 ata1.00: ATA-7: ST9100824AS, 3.14, max UDMA/133
 ata1.00: 195371568 sectors, multi 16: LBA48 NCQ (depth 0/32)
 ata1.00: configured for UDMA/133
 scsi 0:0:0:0: Direct-Access     ATA      ST9100824AS      3.14 PQ: 0 ANSI: 5
 sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
 sd 0:0:0:0: [sda] Write Protect is off
 sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
 DPO or FUA
 sd 0:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
 sd 0:0:0:0: [sda] Write Protect is off
 sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support
 DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
 sd 0:0:0:0: [sda] Attached SCSI disk

 lspci:

 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and
 945GT Express Memory Controller Hub (rev 03)
 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS,
 943/940GML Express Integrated Graphics Controller (rev 03)
 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML
 Express Integrated Graphics Controller (rev 03)
 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition
 Audio Controller (rev 02)
 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1
 (rev 02)
 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2
 (rev 02)
 00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3
 (rev 02)
 00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4
 (rev 02)
 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
 Controller #1 (rev 02)
 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
 Controller #2 (rev 02)
 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
 Controller #3 (rev 02)
 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
 Controller #4 (rev 02)
 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
 Controller (rev 02)
 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge
 (rev 02)
 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller
 (rev 02)
 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE
 Controller (rev 02)
 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
 02:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network
 Connection (rev 02)
 03:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8036 PCI-E Fast
 Ethernet Controller (rev 15)
 05:04.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller
 05:04.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE
 1394 Host Controller
 05:04.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card
 Reader (SD/MMC/MS/MS PRO/xD)

 lspci -vvs 00:1f.2:

00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller
(rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
    Subsystem: Sony Corporation Unknown device 81e6
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin B routed to IRQ 21
    Region 0: I/O ports at 18d0 [size=8]
    Region 1: I/O ports at 18c4 [size=4]
    Region 2: I/O ports at 18c8 [size=8]
    Region 3: I/O ports at 18c0 [size=4]
    Region 4: I/O ports at 18b0 [size=16]
    Region 5: Memory at dc544400 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [70] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-




             reply	other threads:[~2007-10-15 17:14 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2007-10-15 17:14 Guilherme Amadio [this message]
2007-10-26  2:10 ` ata_piix: ICH7 "invalid MAP value 0" msg at boot Tejun Heo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20071015171444.GA9512@vaio \
    --to=guilherme.amadio@gmail.com \
    --cc=linux-ide@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.