From: Stefan Roese <sr@denx.de>
To: Kumar Gala <galak@kernel.crashing.org>
Cc: David Woodhouse <dwmw2@infradead.org>,
linuxppc-dev list <linuxppc-dev@ozlabs.org>
Subject: Re: boards in arch/ppc -> arch/powerpc for 85xx
Date: Tue, 16 Oct 2007 07:28:38 +0200 [thread overview]
Message-ID: <200710160728.38897.sr@denx.de> (raw)
In-Reply-To: <B9E8682B-5455-48EA-B078-CB0EDCB2060A@kernel.crashing.org>
On Tuesday 16 October 2007, Kumar Gala wrote:
> >> I'm willing to look into doing the port over, but would need some
> >> help testing.
> >
> > Yes, it would be greatly appreciated if you could start this
> > TQM85xx port. I
> > will of course do the testing.
>
> Ok, for the TQM85xx code in arch/ppc can I get a few things from you:
>
> 1. what processors does this actually support/run on. I'm guessing
> MPC8541, MPC8555? But not really sure
IIRC there are 4 different versions of the board:
- 8540, 8541, 8555 & 8560
> 2. can you send the results of a bd_info from u-boot on the board
I have two version available right now
8540:
U-Boot 1.3.0-rc2-g527c80f0-dirty (Oct 5 2007 - 15:57:38)
CPU: 8540, Version: 2.0, (0x80300020)
Core: E500, Version: 2.0, (0x80200020)
Clock Configuration:
CPU: 833 MHz, CCB: 333 MHz,
DDR: 166 MHz, LBC: 41 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: TQM8540, serial# TQM8540DCBAD7-APFBC.0204 11341240 4
PCI1: 32 bit, 33 MHz (compiled)
I2C: ready
DTT: 1 is 31 C
DRAM: 256 MB (CL=2.5)
FLASH: 32 MB
L2 cache 256KB: enabled
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1, FEC
PS/2: No device found
Kbd: reset failed, no ACK
Type run flash_nfs to mount root filesystem over NFS
=> bdinfo
memstart = 0x00000000
memsize = 0x10000000
flashstart = 0xFE000000
flashsize = 0x02000000
flashoffset = 0x00000000
sramstart = 0x00000000
sramsize = 0x00000000
immr_base = 0xE0000000
bootflags = 0xE4013F80
intfreq = 833.333 MHz
busfreq = 333.333 MHz
ethaddr = 00:D0:93:08:12:E2
eth1addr = 00:D0:93:08:12:E3
eth2addr = 00:D0:93:08:12:E4
IP addr = 192.168.210.1
baudrate = 115200 bps
8560:
U-Boot 1.2.0-ge9792fc6 (Aug 7 2007 - 08:43:55)
CPU: 8560, Version: 2.0, (0x80700020)
Core: E500, Version: 2.0, (0x80200020)
Clock Configuration:
CPU: 833 MHz, CCB: 333 MHz,
DDR: 166 MHz, LBC: 41 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: TQM8560, serial# TQM8560DCBAD7-APFBC.0204 11301266 4
PCI1: 32 bit, 33 MHz (compiled)
I2C: ready
DTT: 1 is 22 C
DRAM: 256 MB (CL=2.5)
FLASH: 32 MB
L2 cache 256KB: enabled
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1, FCC3 ETHERNET
Type run flash_nfs to mount root filesystem over NFS
Hit any key to stop autoboot: 0
=> bdinfo
memstart = 0x00000000
memsize = 0x10000000
flashstart = 0xFE000000
flashsize = 0x02000000
flashoffset = 0x00000000
sramstart = 0x00000000
sramsize = 0x00000000
immr_base = 0xE0000000
bootflags = 0x00000036
vco = 666.666 MHz
sccfreq = 166.666 MHz
brgfreq = 166.666 MHz
intfreq = 833.333 MHz
cpmfreq = 333.333 MHz
busfreq = 333.333 MHz
ethaddr = 16:CC:31:E8:8C:12
eth1addr = 16:CC:31:E8:8C:13
eth2addr = 16:CC:31:E8:8C:14
IP addr = 192.168.210.2
baudrate = 115200 bps
> 3. can you send me the results of cat /proc/iomem & /proc/ioports
> from a linux boot.
8540:
bash-3.00# cat /proc/iomem
80000000-9fffffff : PCI1 host bridge
9fff8000-9fff9fff : 0000:00:1c.1
9fffbc00-9fffbfff : 0000:00:1c.1
9fffc000-9fffdfff : 0000:00:1c.0
9ffffc00-9fffffff : 0000:00:1c.0
e0003000-e00030ff : fsl-i2c.1
e0004500-e0004507 : serial
e0004600-e0004607 : serial
e0021100-e002117f : fsl-dma.0
e0021180-e00211ff : fsl-dma.1
e0021200-e002127f : fsl-dma.2
e0021280-e00212ff : fsl-dma.3
e0024000-e0024fff : fsl-gianfar.1
e0024520-e002453f : fsl-gianfar_mdio.0
e0025000-e0025fff : fsl-gianfar.2
e0026000-e0026fff : fsl-gianfar.3
e00e1000-e00e1fff : fsl-perfmon.1
bash-3.00# cat /proc/ioports
00000000-00ffffff : PCI1 host bridge
00fffe00-00fffeff : 0000:00:1c.1
00ffff00-00ffffff : 0000:00:1c.0
8560:
-bash-3.2# cat /proc/iomem
80000000-9fffffff : PCI1 host bridge
9f7fdf00-9f7fdfff : 0000:00:1c.0
9fbfe000-9fbfefff : 0000:00:0b.1
9ffff000-9fffffff : 0000:00:0b.0
e0003000-e00030ff : fsl-i2c.1
e0021100-e002117f : fsl-dma.0
e0021180-e00211ff : fsl-dma.1
e0021200-e002127f : fsl-dma.2
e0021280-e00212ff : fsl-dma.3
e0024000-e0024fff : fsl-gianfar.1
e0024520-e002453f : fsl-gianfar_mdio.0
e0025000-e0025fff : fsl-gianfar.2
e0088400-e00884ff : fcc_pram
e0088500-e00885ff : fcc_pram
e0088600-e00886ff : fcc_pram
e0091300-e009131f : fcc_regs
e0091320-e009133f : fcc_regs
e0091340-e009135f : fcc_regs
e0091380-e009139f : fcc_regs_c
e00913a0-e00913cf : fcc_regs_c
e00913d0-e00913ff : fcc_regs_c
e0091860-e00918bf : fsl-cpm-i2c.1
e0091a00-e0091a1f : fsl-cpm-scc.1
e0091a20-e0091a3f : fsl-cpm-scc.2
e0091a40-e0091a5f : fsl-cpm-scc.3
e0091a60-e0091a7f : fsl-cpm-scc.4
e0091aa0-e0091aff : fsl-cpm-spi.1
e0091b30-e0091b3f : fsl-cpm-mcc.1
e0091b50-e0091b5f : fsl-cpm-mcc.2
e00e1000-e00e1fff : fsl-perfmon.1
-bash-3.2# cat /proc/ioports
00000000-00ffffff : PCI1 host bridge
00ff7f00-00ff7fff : 0000:00:1c.0
Thanks.
Best regards,
Stefan
next prev parent reply other threads:[~2007-10-16 5:28 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-10-15 23:07 boards in arch/ppc -> arch/powerpc for 85xx Kumar Gala
2007-10-15 23:34 ` Wolfgang Denk
2007-10-16 4:32 ` Dan Malek
2007-10-16 4:40 ` Stefan Roese
2007-10-16 5:06 ` Kumar Gala
2007-10-16 5:28 ` Stefan Roese [this message]
2007-10-16 5:51 ` Kumar Gala
2007-10-16 6:06 ` Wolfgang Denk
2007-10-16 6:15 ` Stefan Roese
2007-10-17 18:39 ` David Woodhouse
2007-10-18 0:54 ` Kumar Gala
2007-10-18 7:37 ` Geert Uytterhoeven
2007-10-20 12:19 ` David Woodhouse
2007-10-18 14:29 ` Bruce Ashfield
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200710160728.38897.sr@denx.de \
--to=sr@denx.de \
--cc=dwmw2@infradead.org \
--cc=galak@kernel.crashing.org \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.