From: Michael Schwingen <michael@schwingen.org>
To: u-boot@lists.denx.de
Subject: [U-Boot-Users] PATCH (resend): support JEDEC flash roms in?CFI-flash framework
Date: Fri, 7 Dec 2007 23:35:02 +0100 [thread overview]
Message-ID: <20071207223502.GA11677@discworld.dascon.de> (raw)
In-Reply-To: <200712070942.52699.sr@denx.de>
On Fri, Dec 07, 2007 at 09:42:52AM +0100, Stefan Roese wrote:
> Michael, could you please redo your patches very soon? I just updated the
> cfi-flash custodian repository. Best would be today. :)
Okay, I got it working - it seems I need to learn a bit more about git, so
this is just a normal diff between a current tree vs. a patched one.
I renamed CFG_FLASH_CFI_LEGACY to CONFIG_FLASH_CFI_LEGACY so that it is
picked up by autoconf.mk.
BTW: what is the best method to get other patches in? I have 4 general
IXP42x patches which I sent to the list on 2007-11-10 and which got no
comments, plus patches to add support for 4 boards that go on top of these
(one of which needs the flash patch below).
cu
Michael
the following patch adds support for non-CFI flash ROMS, by hooking into the
CFI flash code and using most of its code, as recently discussed here in the
thread "Mixing CFI and non-CFI flashs".
Signed-off-by: Michael Schwingen <michael@schwingen.org>
diff --ignore-space -urN u-boot/drivers/mtd/Makefile u-boot-ms/drivers/mtd/Makefile
--- u-boot/drivers/mtd/Makefile 2007-12-07 22:48:37.000000000 +0100
+++ u-boot-ms/drivers/mtd/Makefile 2007-12-07 21:17:02.000000000 +0100
@@ -29,6 +29,7 @@
COBJS-y += cfi_flash.o
COBJS-y += dataflash.o
COBJS-y += mw_eeprom.o
+COBJS-$(CONFIG_FLASH_CFI_LEGACY) += jedec_flash.o
COBJS := $(COBJS-y)
SRCS := $(COBJS:.o=.c)
diff --ignore-space -urN u-boot/drivers/mtd/cfi_flash.c u-boot-ms/drivers/mtd/cfi_flash.c
--- u-boot/drivers/mtd/cfi_flash.c 2007-12-07 22:48:37.000000000 +0100
+++ u-boot-ms/drivers/mtd/cfi_flash.c 2007-12-07 22:37:10.000000000 +0100
@@ -98,10 +99,6 @@
#define AMD_STATUS_TOGGLE 0x40
#define AMD_STATUS_ERROR 0x20
-#define AMD_ADDR_ERASE_START ((info->portwidth == FLASH_CFI_8BIT) ? 0xAAA : 0x555)
-#define AMD_ADDR_START ((info->portwidth == FLASH_CFI_8BIT) ? 0xAAA : 0x555)
-#define AMD_ADDR_ACK ((info->portwidth == FLASH_CFI_8BIT) ? 0x555 : 0x2AA)
-
#define FLASH_OFFSET_MANUFACTURER_ID 0x00
#define FLASH_OFFSET_DEVICE_ID 0x01
#define FLASH_OFFSET_DEVICE_ID2 0x0E
@@ -331,6 +328,62 @@
}
+#ifdef CONFIG_FLASH_CFI_LEGACY
+/*-----------------------------------------------------------------------
+ * Call board code to request info about non-CFI flash.
+ * board_flash_get_legacy needs to fill in at least:
+ * info->portwidth, info->chipwidth and info->interface for Jedec probing.
+ */
+int flash_detect_legacy(ulong base, int banknum)
+{
+ flash_info_t *info = &flash_info[banknum];
+ if (board_flash_get_legacy(base, banknum, info)) {
+ /* board code may have filled info completely. If not, we
+ use JEDEC ID probing. */
+ if (!info->vendor) {
+ int modes[] = { CFI_CMDSET_AMD_STANDARD, CFI_CMDSET_INTEL_STANDARD };
+ int i;
+
+ for(i=0; i<sizeof(modes)/sizeof(modes[0]); i++) {
+ info->vendor = modes[i];
+ info->start[0] = base;
+ if (info->portwidth == FLASH_CFI_8BIT && info->interface == FLASH_CFI_X8X16) {
+ info->addr_unlock1 = 0x2AAA;
+ info->addr_unlock2 = 0x5555;
+ } else {
+ info->addr_unlock1 = 0x5555;
+ info->addr_unlock2 = 0x2AAA;
+ }
+ flash_read_jedec_ids(info);
+ debug("JEDEC PROBE: ID %x %x %x\n", info->manufacturer_id, info->device_id, info->device_id2);
+ if (jedec_flash_match(info, base))
+ break;
+ }
+ }
+ switch(info->vendor) {
+ case CFI_CMDSET_INTEL_STANDARD:
+ case CFI_CMDSET_INTEL_EXTENDED:
+ info->cmd_reset = FLASH_CMD_RESET;
+ break;
+ case CFI_CMDSET_AMD_STANDARD:
+ case CFI_CMDSET_AMD_EXTENDED:
+ case CFI_CMDSET_AMD_LEGACY:
+ info->cmd_reset = AMD_CMD_RESET;
+ break;
+ }
+ info->flash_id = FLASH_MAN_CFI;
+ return 1;
+ }
+ return 0; /* use CFI */
+}
+#else
+int inline flash_detect_legacy(ulong base, int banknum)
+{
+ return 0; /* use CFI */
+}
+#endif
+
+
/*-----------------------------------------------------------------------
*/
unsigned long flash_init (void)
@@ -345,7 +398,10 @@
/* Init: no FLASHes known */
for (i = 0; i < CFG_MAX_FLASH_BANKS; ++i) {
flash_info[i].flash_id = FLASH_UNKNOWN;
- size += flash_info[i].size = flash_get_size (bank_base[i], i);
+
+ if (!flash_detect_legacy (bank_base[i], i))
+ flash_get_size (bank_base[i], i);
+ size += flash_info[i].size;
if (flash_info[i].flash_id == FLASH_UNKNOWN) {
#ifndef CFG_FLASH_QUIET_TEST
printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx = %ld MB\n",
@@ -483,11 +539,18 @@
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
flash_unlock_seq (info, sect);
- flash_write_cmd (info, sect, AMD_ADDR_ERASE_START,
- AMD_CMD_ERASE_START);
+ flash_write_cmd (info, sect, info->addr_unlock1, AMD_CMD_ERASE_START);
flash_unlock_seq (info, sect);
flash_write_cmd (info, sect, 0, AMD_CMD_ERASE_SECTOR);
break;
+#ifdef CONFIG_FLASH_CFI_LEGACY
+ case CFI_CMDSET_AMD_LEGACY:
+ flash_unlock_seq (info, 0);
+ flash_write_cmd (info, 0, info->addr_unlock1, AMD_CMD_ERASE_START);
+ flash_unlock_seq (info, 0);
+ flash_write_cmd (info, sect, 0, AMD_CMD_ERASE_SECTOR);
+ break;
+#endif
default:
debug ("Unkown flash vendor %d\n",
info->vendor);
@@ -516,8 +579,13 @@
return;
}
- printf ("CFI conformant FLASH (%d x %d)",
+ printf ("%s FLASH (%d x %d)",
+ info->name,
(info->portwidth << 3), (info->chipwidth << 3));
+ if (info->size < 1024*1024)
+ printf (" Size: %ld kB in %d Sectors\n",
+ info->size >> 10, info->sector_count);
+ else
printf (" Size: %ld MB in %d Sectors\n",
info->size >> 20, info->sector_count);
printf (" ");
@@ -534,6 +602,11 @@
case CFI_CMDSET_AMD_EXTENDED:
printf ("AMD Extended");
break;
+#ifdef CONFIG_FLASH_CFI_LEGACY
+ case CFI_CMDSET_AMD_LEGACY:
+ printf ("AMD Legacy");
+ break;
+#endif
default:
printf ("Unknown (%d)", info->vendor);
break;
@@ -777,6 +850,9 @@
break;
case CFI_CMDSET_AMD_STANDARD:
case CFI_CMDSET_AMD_EXTENDED:
+#ifdef CONFIG_FLASH_CFI_LEGACY
+ case CFI_CMDSET_AMD_LEGACY:
+#endif
retval = flash_toggle (info, sect, 0, AMD_STATUS_TOGGLE);
break;
default:
@@ -967,8 +1043,8 @@
static void flash_unlock_seq (flash_info_t * info, flash_sect_t sect)
{
- flash_write_cmd (info, sect, AMD_ADDR_START, AMD_CMD_UNLOCK_START);
- flash_write_cmd (info, sect, AMD_ADDR_ACK, AMD_CMD_UNLOCK_ACK);
+ flash_write_cmd (info, sect, info->addr_unlock1, AMD_CMD_UNLOCK_START);
+ flash_write_cmd (info, sect, info->addr_unlock2, AMD_CMD_UNLOCK_ACK);
}
/*-----------------------------------------------------------------------
@@ -1105,7 +1181,7 @@
case CFI_CMDSET_AMD_EXTENDED:
flash_write_cmd(info, 0, 0, AMD_CMD_RESET);
flash_unlock_seq(info, 0);
- flash_write_cmd(info, 0, AMD_ADDR_START, FLASH_CMD_READ_ID);
+ flash_write_cmd(info, 0, info->addr_unlock1, FLASH_CMD_READ_ID);
udelay(1000); /* some flash are slow to respond */
info->manufacturer_id = flash_read_uchar (info,
FLASH_OFFSET_MANUFACTURER_ID);
@@ -1156,6 +1232,10 @@
debug ("port %d bits chip %d bits\n",
info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
+ /* this probably only works if info->interface == FLASH_CFI_X8X16 */
+ info->addr_unlock1 = (info->portwidth == FLASH_CFI_8BIT) ? 0xAAA : 0x555;
+ info->addr_unlock2 = (info->portwidth == FLASH_CFI_8BIT) ? 0x555 : 0x2AA;
+ info->name = "CFI conformant";
return 1;
}
}
@@ -1282,6 +1362,10 @@
debug ("erase_region_count = %d erase_region_size = %d\n",
erase_region_count, erase_region_size);
for (j = 0; j < erase_region_count; j++) {
+ if (sect_cnt >= CFG_MAX_FLASH_SECT) {
+ printf("ERROR: too many flash sectors\n");
+ break;
+ }
info->start[sect_cnt] = sector;
sector += (erase_region_size * size_ratio);
@@ -1384,8 +1468,11 @@
break;
case CFI_CMDSET_AMD_EXTENDED:
case CFI_CMDSET_AMD_STANDARD:
+#ifdef CONFIG_FLASH_CFI_LEGACY
+ case CFI_CMDSET_AMD_LEGACY:
+#endif
flash_unlock_seq (info, 0);
- flash_write_cmd (info, 0, AMD_ADDR_START, AMD_CMD_WRITE);
+ flash_write_cmd (info, 0, info->addr_unlock1, AMD_CMD_WRITE);
break;
}
diff --ignore-space -urN u-boot/drivers/mtd/jedec_flash.c u-boot-ms/drivers/mtd/jedec_flash.c
--- u-boot/drivers/mtd/jedec_flash.c 1970-01-01 01:00:00.000000000 +0100
+++ u-boot-ms/drivers/mtd/jedec_flash.c 2007-12-07 22:40:04.000000000 +0100
@@ -0,0 +1,312 @@
+/*
+ * (C) Copyright 2007
+ * Michael Schwingen, <michael@schwingen.org>
+ *
+ * based in great part on jedec_probe.c from linux kernel:
+ * (C) 2000 Red Hat. GPL'd.
+ * Occasionally maintained by Thayne Harbaugh tharbaugh at lnxi dot com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+/* The DEBUG define must be before common to enable debugging */
+/*#define DEBUG*/
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+#include <asm/byteorder.h>
+#include <environment.h>
+
+#define P_ID_AMD_STD CFI_CMDSET_AMD_LEGACY
+
+/* Manufacturers */
+#define MANUFACTURER_AMD 0x0001
+#define MANUFACTURER_SST 0x00BF
+
+/* AMD */
+#define AM29DL800BB 0x22C8
+#define AM29DL800BT 0x224A
+
+#define AM29F800BB 0x2258
+#define AM29F800BT 0x22D6
+#define AM29LV400BB 0x22BA
+#define AM29LV400BT 0x22B9
+#define AM29LV800BB 0x225B
+#define AM29LV800BT 0x22DA
+#define AM29LV160DT 0x22C4
+#define AM29LV160DB 0x2249
+#define AM29F017D 0x003D
+#define AM29F016D 0x00AD
+#define AM29F080 0x00D5
+#define AM29F040 0x00A4
+#define AM29LV040B 0x004F
+#define AM29F032B 0x0041
+#define AM29F002T 0x00B0
+
+/* SST */
+#define SST39LF800 0x2781
+#define SST39LF160 0x2782
+#define SST39VF1601 0x234b
+#define SST39LF512 0x00D4
+#define SST39LF010 0x00D5
+#define SST39LF020 0x00D6
+#define SST39LF040 0x00D7
+#define SST39SF010A 0x00B5
+#define SST39SF020A 0x00B6
+
+
+/*
+ * Unlock address sets for AMD command sets.
+ * Intel command sets use the MTD_UADDR_UNNECESSARY.
+ * Each identifier, except MTD_UADDR_UNNECESSARY, and
+ * MTD_UADDR_NO_SUPPORT must be defined below in unlock_addrs[].
+ * MTD_UADDR_NOT_SUPPORTED must be 0 so that structure
+ * initialization need not require initializing all of the
+ * unlock addresses for all bit widths.
+ */
+enum uaddr {
+ MTD_UADDR_NOT_SUPPORTED = 0, /* data width not supported */
+ MTD_UADDR_0x0555_0x02AA,
+ MTD_UADDR_0x0555_0x0AAA,
+ MTD_UADDR_0x5555_0x2AAA,
+ MTD_UADDR_0x0AAA_0x0555,
+ MTD_UADDR_DONT_CARE, /* Requires an arbitrary address */
+ MTD_UADDR_UNNECESSARY, /* Does not require any address */
+};
+
+
+struct unlock_addr {
+ u32 addr1;
+ u32 addr2;
+};
+
+
+/*
+ * I don't like the fact that the first entry in unlock_addrs[]
+ * exists, but is for MTD_UADDR_NOT_SUPPORTED - and, therefore,
+ * should not be used. The problem is that structures with
+ * initializers have extra fields initialized to 0. It is _very_
+ * desireable to have the unlock address entries for unsupported
+ * data widths automatically initialized - that means that
+ * MTD_UADDR_NOT_SUPPORTED must be 0 and the first entry here
+ * must go unused.
+ */
+static const struct unlock_addr unlock_addrs[] = {
+ [MTD_UADDR_NOT_SUPPORTED] = {
+ .addr1 = 0xffff,
+ .addr2 = 0xffff
+ },
+
+ [MTD_UADDR_0x0555_0x02AA] = {
+ .addr1 = 0x0555,
+ .addr2 = 0x02aa
+ },
+
+ [MTD_UADDR_0x0555_0x0AAA] = {
+ .addr1 = 0x0555,
+ .addr2 = 0x0aaa
+ },
+
+ [MTD_UADDR_0x5555_0x2AAA] = {
+ .addr1 = 0x5555,
+ .addr2 = 0x2aaa
+ },
+
+ [MTD_UADDR_0x0AAA_0x0555] = {
+ .addr1 = 0x0AAA,
+ .addr2 = 0x0555
+ },
+
+ [MTD_UADDR_DONT_CARE] = {
+ .addr1 = 0x0000, /* Doesn't matter which address */
+ .addr2 = 0x0000 /* is used - must be last entry */
+ },
+
+ [MTD_UADDR_UNNECESSARY] = {
+ .addr1 = 0x0000,
+ .addr2 = 0x0000
+ }
+};
+
+
+struct amd_flash_info {
+ const __u16 mfr_id;
+ const __u16 dev_id;
+ const char *name;
+ const int DevSize;
+ const int NumEraseRegions;
+ const int CmdSet;
+ const __u8 uaddr[4]; /* unlock addrs for 8, 16, 32, 64 */
+ const ulong regions[6];
+};
+
+#define ERASEINFO(size,blocks) (size<<8)|(blocks-1)
+
+#define SIZE_64KiB 16
+#define SIZE_128KiB 17
+#define SIZE_256KiB 18
+#define SIZE_512KiB 19
+#define SIZE_1MiB 20
+#define SIZE_2MiB 21
+#define SIZE_4MiB 22
+#define SIZE_8MiB 23
+
+static const struct amd_flash_info jedec_table[] = {
+#ifdef CFG_FLASH_LEGACY_256Kx8
+ {
+ .mfr_id = MANUFACTURER_SST,
+ .dev_id = SST39LF020,
+ .name = "SST 39LF020",
+ .uaddr = {
+ [0] = MTD_UADDR_0x5555_0x2AAA /* x8 */
+ },
+ .DevSize = SIZE_256KiB,
+ .CmdSet = P_ID_AMD_STD,
+ .NumEraseRegions= 1,
+ .regions = {
+ ERASEINFO(0x01000,64),
+ }
+ },
+#endif
+#ifdef CFG_FLASH_LEGACY_512Kx8
+ {
+ .mfr_id = MANUFACTURER_AMD,
+ .dev_id = AM29LV040B,
+ .name = "AMD AM29LV040B",
+ .uaddr = {
+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */
+ },
+ .DevSize = SIZE_512KiB,
+ .CmdSet = P_ID_AMD_STD,
+ .NumEraseRegions= 1,
+ .regions = {
+ ERASEINFO(0x10000,8),
+ }
+ },
+ {
+ .mfr_id = MANUFACTURER_SST,
+ .dev_id = SST39LF040,
+ .name = "SST 39LF040",
+ .uaddr = {
+ [0] = MTD_UADDR_0x5555_0x2AAA /* x8 */
+ },
+ .DevSize = SIZE_512KiB,
+ .CmdSet = P_ID_AMD_STD,
+ .NumEraseRegions= 1,
+ .regions = {
+ ERASEINFO(0x01000,128),
+ }
+ },
+#endif
+};
+
+
+#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
+
+
+static inline void fill_info(flash_info_t *info, const struct amd_flash_info *jedec_entry, ulong base)
+{
+ int i,j;
+ int sect_cnt;
+ int size_ratio;
+ int total_size;
+ enum uaddr uaddr_idx;
+
+ size_ratio = info->portwidth / info->chipwidth;
+
+ debug("Found JEDEC Flash: %s\n", jedec_entry->name);
+ info->vendor = jedec_entry->CmdSet;
+ /* Todo: do we need device-specific timeouts? */
+ info->erase_blk_tout = 30000;
+ info->buffer_write_tout = 1000;
+ info->write_tout = 100;
+ info->name = jedec_entry->name;
+
+ /* copy unlock addresses from device table to CFI info struct. This
+ is just here because the addresses are in the table anyway - if
+ the flash is not detected due to wrong unlock addresses,
+ flash_detect_legacy would have to try all of them before we even
+ get here. */
+ switch(info->chipwidth) {
+ case FLASH_CFI_8BIT:
+ uaddr_idx = jedec_entry->uaddr[0];
+ break;
+ case FLASH_CFI_16BIT:
+ uaddr_idx = jedec_entry->uaddr[1];
+ break;
+ case FLASH_CFI_32BIT:
+ uaddr_idx = jedec_entry->uaddr[2];
+ break;
+ default:
+ uaddr_idx = MTD_UADDR_NOT_SUPPORTED;
+ break;
+ }
+
+ debug("unlock address index %d\n", uaddr_idx);
+ info->addr_unlock1 = unlock_addrs[uaddr_idx].addr1;
+ info->addr_unlock2 = unlock_addrs[uaddr_idx].addr2;
+ debug("unlock addresses are 0x%x/0x%x\n", info->addr_unlock1, info->addr_unlock2);
+
+ sect_cnt = 0;
+ total_size = 0;
+ for (i = 0; i < jedec_entry->NumEraseRegions; i++) {
+ ulong erase_region_size = jedec_entry->regions[i] >> 8;
+ ulong erase_region_count = (jedec_entry->regions[i] & 0xff) + 1;
+
+ total_size += erase_region_size * erase_region_count;
+ debug ("erase_region_count = %d erase_region_size = %d\n",
+ erase_region_count, erase_region_size);
+ for (j = 0; j < erase_region_count; j++) {
+ if (sect_cnt >= CFG_MAX_FLASH_SECT) {
+ printf("ERROR: too many flash sectors\n");
+ break;
+ }
+ info->start[sect_cnt] = base;
+ base += (erase_region_size * size_ratio);
+ sect_cnt++;
+ }
+ }
+ info->sector_count = sect_cnt;
+ info->size = total_size * size_ratio;
+}
+
+/*-----------------------------------------------------------------------
+ * match jedec ids against table. If a match is found, fill flash_info entry
+ */
+int jedec_flash_match(flash_info_t *info, ulong base)
+{
+ int ret = 0;
+ int i;
+ ulong mask = 0xFFFF;
+ if (info->chipwidth == 1)
+ mask = 0xFF;
+
+ for (i = 0; i < ARRAY_SIZE(jedec_table); i++) {
+ if ((jedec_table[i].mfr_id & mask) == (info->manufacturer_id & mask) &&
+ (jedec_table[i].dev_id & mask) == (info->device_id & mask)) {
+ fill_info(info, &jedec_table[i], base);
+ ret = 1;
+ break;
+ }
+ }
+ return ret;
+}
+
diff --ignore-space -urN u-boot/include/flash.h u-boot-ms/include/flash.h
--- u-boot/include/flash.h 2007-12-07 22:48:39.000000000 +0100
+++ u-boot-ms/include/flash.h 2007-12-07 21:56:21.000000000 +0100
@@ -52,6 +52,9 @@
ushort ext_addr; /* extended query table address */
ushort cfi_version; /* cfi version */
ushort cfi_offset; /* offset for cfi query */
+ ulong addr_unlock1; /* unlock address 1 for AMD flash roms */
+ ulong addr_unlock2; /* unlock address 2 for AMD flash roms */
+ const char *name; /* human-readable name */
#endif
} flash_info_t;
@@ -101,6 +104,13 @@
extern void flash_read_factory_serial(flash_info_t * info, void * buffer, int offset, int len);
#endif /* CFG_FLASH_PROTECTION */
+#ifdef CONFIG_FLASH_CFI_LEGACY
+extern ulong board_flash_get_legacy(ulong base, int banknum, flash_info_t *info);
+extern int jedec_flash_match(flash_info_t *info, ulong base);
+#define CFI_CMDSET_AMD_LEGACY 0xFFF0
+#endif
+
+
/*-----------------------------------------------------------------------
* return codes from flash_write():
*/
next prev parent reply other threads:[~2007-12-07 22:35 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-11-12 20:23 [U-Boot-Users] PATCH: support JEDEC flash roms in CFI-flash framework Michael Schwingen
2007-11-13 14:45 ` Stefan Roese
2007-11-13 19:13 ` Michael Schwingen
2007-11-13 15:26 ` Bartlomiej Sieka
2007-11-13 18:59 ` Michael Schwingen
2007-11-13 20:56 ` Stefan Roese
2007-11-24 17:45 ` [U-Boot-Users] PATCH (resend): " Michael Schwingen
2007-11-26 18:57 ` Michael Schwingen
2007-12-05 15:58 ` Bartlomiej Sieka
2007-12-05 22:25 ` Michael Schwingen
2007-12-05 22:40 ` Bartlomiej Sieka
2007-12-07 8:42 ` Stefan Roese
2007-12-07 22:35 ` Michael Schwingen [this message]
2007-12-08 7:31 ` [U-Boot-Users] PATCH (resend): support JEDEC flash roms in?CFI-flash framework Stefan Roese
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20071207223502.GA11677@discworld.dascon.de \
--to=michael@schwingen.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.