Re: [patch 3/6] Minor typos in i2c/algos/Kconfig

[Jean Delvare <khali-PUYAD+kWke1g9hUCZPvPmw@public.gmane.org>]

Hi Wolfram,

On Mon, 21 Jan 2008 15:20:13 +0100, w.sang-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org wrote:
> This patch corrects some minor typos. The term "below" in these paragraphs
> might also be replaced by "later" or something similar?

You're right, this is a remnant from the times where all the i2c
options were in a single menu. Nowadays, 'under "I2C Hardware Bus
support"' would be more appropriate. Or... nothing at all. After all,
the i2c "algorithm" modules are selected automatically whenever a
driver that relies on them is selected. They are visible in the menu
only so that one can enable them for an hypothetical out-of-tree driver
- but I doubt that this is terribly useful. So a 3rd option would be to
simply remove these items from the configuration menu.

> 
> Signed-off-by: Wolfram Sang <w.sang-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> ---
>  drivers/i2c/algos/Kconfig |    6 +++---
>  1 file changed, 3 insertions(+), 3 deletions(-)
> 
> Index: linux-playground/drivers/i2c/algos/Kconfig
> ===================================================================
> --- linux-playground.orig/drivers/i2c/algos/Kconfig	2008-01-21 11:04:53.000000000 +0100
> +++ linux-playground/drivers/i2c/algos/Kconfig	2008-01-21 11:35:19.000000000 +0100
> @@ -9,7 +9,7 @@
>  	help
>  	  This allows you to use a range of I2C adapters called bit-banging
>  	  adapters.  Say Y if you own an I2C adapter belonging to this class
> -	  and then say Y to the specific driver for you adapter below.
> +	  and then say Y to the specific driver for your adapter below.
>  
>  	  This support is also available as a module.  If so, the module 
>  	  will be called i2c-algo-bit.
> @@ -19,7 +19,7 @@
>  	help
>  	  This allows you to use a range of I2C adapters called PCF adapters.
>  	  Say Y if you own an I2C adapter belonging to this class and then say
> -	  Y to the specific driver for you adapter below.
> +	  Y to the specific driver for your adapter below.
>  
>  	  This support is also available as a module.  If so, the module 
>  	  will be called i2c-algo-pcf.
> @@ -29,7 +29,7 @@
>  	help
>  	  This allows you to use a range of I2C adapters called PCA adapters.
>  	  Say Y if you own an I2C adapter belonging to this class and then say
> -	  Y to the specific driver for you adapter below.
> +	  Y to the specific driver for your adapter below.
>  
>  	  This support is also available as a module.  If so, the module 
>  	  will be called i2c-algo-pca.
> 


-- 
Jean Delvare

_______________________________________________
i2c mailing list
i2c-GZX6beZjE8VD60Wz+7aTrA@public.gmane.org
http://lists.lm-sensors.org/mailman/listinfo/i2c