From: akpm@linux-foundation.org
To: jirislaby@gmail.com, alan@redhat.com, mm-commits@vger.kernel.org
Subject: - char-mxser-add-support-for-cp-114ul.patch removed from -mm tree
Date: Fri, 08 Feb 2008 00:10:13 -0800 [thread overview]
Message-ID: <200802080809.m1889sPB014884@imap1.linux-foundation.org> (raw)
The patch titled
Char: mxser, add support for CP-114UL
has been removed from the -mm tree. Its filename was
char-mxser-add-support-for-cp-114ul.patch
This patch was dropped because it was merged into mainline or a subsystem tree
The current -mm tree may be found at http://userweb.kernel.org/~akpm/mmotm/
------------------------------------------------------
Subject: Char: mxser, add support for CP-114UL
From: Jiri Slaby <jirislaby@gmail.com>
Add new card (0x1393:0x1143) support added in 1.11 original driver, also
allow rate change in set_serial_info ioctl (as per 1.11 too).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Reviewed-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---
drivers/char/mxser.c | 29 +++++++++++++++++++----------
1 file changed, 19 insertions(+), 10 deletions(-)
diff -puN drivers/char/mxser.c~char-mxser-add-support-for-cp-114ul drivers/char/mxser.c
--- a/drivers/char/mxser.c~char-mxser-add-support-for-cp-114ul
+++ a/drivers/char/mxser.c
@@ -1,8 +1,8 @@
/*
* mxser.c -- MOXA Smartio/Industio family multiport serial driver.
*
- * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com.tw).
- * Copyright (C) 2006-2007 Jiri Slaby <jirislaby@gmail.com>
+ * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com).
+ * Copyright (C) 2006-2008 Jiri Slaby <jirislaby@gmail.com>
*
* This code is loosely based on the 1.8 moxa driver which is based on
* Linux serial driver, written by Linus Torvalds, Theodore T'so and
@@ -47,7 +47,7 @@
#include "mxser.h"
-#define MXSER_VERSION "2.0.2" /* 1.10 */
+#define MXSER_VERSION "2.0.3" /* 1.11 */
#define MXSERMAJOR 174
#define MXSERCUMAJOR 175
@@ -73,6 +73,7 @@
#define PCI_DEVICE_ID_CB108 0x1080
#define PCI_DEVICE_ID_CB114 0x1142
+#define PCI_DEVICE_ID_CP114UL 0x1143
#define PCI_DEVICE_ID_CB134I 0x1341
#define PCI_DEVICE_ID_CP138U 0x1380
#define PCI_DEVICE_ID_POS104UL 0x1044
@@ -140,7 +141,8 @@ static const struct mxser_cardinfo mxser
/*25*/ { "CB-114 series", 4, },
{ "CB-134I series", 4, },
{ "CP-138U series", 8, },
- { "POS-104UL series", 4, }
+ { "POS-104UL series", 4, },
+ { "CP-114UL series", 4, }
};
/* driver_data correspond to the lines in the structure above
@@ -169,6 +171,7 @@ static struct pci_device_id mxser_pcibrd
{ PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I), .driver_data = 26 },
{ PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U), .driver_data = 27 },
{ PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 },
+ { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114UL), .driver_data = 29 },
{ }
};
MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
@@ -1188,20 +1191,19 @@ static int mxser_set_serial_info(struct
struct serial_struct __user *new_info)
{
struct serial_struct new_serial;
+ speed_t baud;
unsigned long sl_flags;
unsigned int flags;
int retval = 0;
if (!new_info || !info->ioaddr)
- return -EFAULT;
+ return -ENODEV;
if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
return -EFAULT;
- if ((new_serial.irq != info->board->irq) ||
- (new_serial.port != info->ioaddr) ||
- (new_serial.custom_divisor != info->custom_divisor) ||
- (new_serial.baud_base != info->baud_base))
- return -EPERM;
+ if (new_serial.irq != info->board->irq ||
+ new_serial.port != info->ioaddr)
+ return -EINVAL;
flags = info->flags & ASYNC_SPD_MASK;
@@ -1224,6 +1226,13 @@ static int mxser_set_serial_info(struct
info->tty->low_latency =
(info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
info->tty->low_latency = 0;
+ if ((info->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
+ (new_serial.baud_base != info->baud_base ||
+ new_serial.custom_divisor !=
+ info->custom_divisor)) {
+ baud = new_serial.baud_base / new_serial.custom_divisor;
+ tty_encode_baud_rate(info->tty, baud, baud);
+ }
}
info->type = new_serial.type;
_
Patches currently in -mm which might be from jirislaby@gmail.com are
origin.patch
git-drm.patch
drm-i915-fix-oops-after-killing-x.patch
git-watchdog.patch
moxa-first-pass-at-termios-reporting.patch
char-applicom-use-pci_resource_start.patch
char-applicom-use-pci_match_id.patch
char-applicom-use-pci_match_id-fix.patch
reiser4.patch
shrink_slab-handle-bad-shrinkers.patch
reply other threads:[~2008-02-08 8:19 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200802080809.m1889sPB014884@imap1.linux-foundation.org \
--to=akpm@linux-foundation.org \
--cc=alan@redhat.com \
--cc=jirislaby@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mm-commits@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.