From: "J.A. Magallón" <jamagallon@ono.com>
To: "Linux-Kernel, " <linux-kernel@vger.kernel.org>
Subject: DRDY errors again
Date: Tue, 8 Apr 2008 17:13:11 +0200 [thread overview]
Message-ID: <20080408171311.69441c8b@werewolf> (raw)
Hi all...
Well, I'm getting all those errors on SATA disks again. I have just returned
one thinkin it was faulty. But I don't buy I got all the bad drives in the
store...
Disks:
werewolf:~> lsscsi -H
[0] aic79xx
[1] aic79xx
[2] ata_piix
[3] ata_piix
[4] ata_piix
[5] ata_piix
werewolf:~> lsscsi
[1:0:0:0] disk SEAGATE ST336807LW 0C01 /dev/sda
[1:0:1:0] disk SEAGATE ST336807LW 0C01 /dev/sdb
[2:0:0:0] disk ATA ST3120022A 3.06 /dev/sdc
[2:0:1:0] cd/dvd HL-DT-ST DVDRAM GSA-H10N JL12 /dev/sr0
[4:0:0:0] disk ATA WDC WD3200AVJS-6 12.0 /dev/sdd
[5:0:0:0] disk ATA ST3500820AS SD25 /dev/sde
dmesg:
scsi0 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
ACPI: PCI Interrupt 0000:03:0a.1[B] -> GSI 23 (level, low) -> IRQ 17
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 29320 Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs
scsi 1:0:0:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3
target1:0:0: asynchronous
scsi1:A:0:0: Tagged Queuing enabled. Depth 32
target1:0:0: Beginning Domain Validation
target1:0:0: wide asynchronous
target1:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63)
target1:0:0: Ending Domain Validation
scsi 1:0:1:0: Direct-Access SEAGATE ST336807LW 0C01 PQ: 0 ANSI: 3
target1:0:1: asynchronous
scsi1:A:1:0: Tagged Queuing enabled. Depth 32
target1:0:1: Beginning Domain Validation
target1:0:1: wide asynchronous
target1:0:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RDSTRM WRFLOW PCOMP (6.25 ns, offset 63)
target1:0:1: Ending Domain Validation
Driver 'sd' needs updating - please use bus_type methods
sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: ab 00 10 08
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 1:0:0:0: [sda] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: ab 00 10 08
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2
sd 1:0:0:0: [sda] Attached SCSI disk
sd 1:0:1:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: ab 00 10 08
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 1:0:1:0: [sdb] 71687372 512-byte hardware sectors (36704 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: ab 00 10 08
sd 1:0:1:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: sdb1
sd 1:0:1:0: [sdb] Attached SCSI disk
Driver 'sr' needs updating - please use bus_type methods
ata_piix 0000:00:1f.1: version 2.12
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
ata1.00: ATA-6: ST3120022A, 3.06, max UDMA/100
ata1.00: 234441648 sectors, multi 16: LBA48
ata1.01: ATAPI: HL-DT-ST DVDRAM GSA-H10N, JL12, max UDMA/33
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/33
scsi 2:0:0:0: Direct-Access ATA ST3120022A 3.06 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdc] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdc] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI disk
scsi 2:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-H10N JL12 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:1:0: Attached scsi CD-ROM sr0
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi4 : ata_piix
scsi5 : ata_piix
ata3: SATA max UDMA/133 cmd 0xc000 ctl 0xc400 bmdma 0xd000 irq 18
ata4: SATA max UDMA/133 cmd 0xc800 ctl 0xcc00 bmdma 0xd008 irq 18
ata3.00: ATA-8: WDC WD3200AVJS-63WDA0, 12.01B02, max UDMA/133
ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
ata4.00: ATA-8: ST3500820AS, SD25, max UDMA/133
ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata4.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA WDC WD3200AVJS-6 12.0 PQ: 0 ANSI: 5
sd 4:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 4:0:0:0: [sdd] Attached SCSI disk
scsi 5:0:0:0: Direct-Access ATA ST3500820AS SD25 PQ: 0 ANSI: 5
sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB)
sd 5:0:0:0: [sde] Write Protect is off
sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB)
sd 5:0:0:0: [sde] Write Protect is off
sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sde: sde1
sd 5:0:0:0: [sde] Attached SCSI disk
The WDC is the new brand disk I received in change for the 'faulty' Seagate.
The ST3500820AS is also new.
This happened burning a data DVD:
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata4.00: cmd b0/d8:00:00:4f:c2/00:00:00:00:00/00 tag 0
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: soft resetting link
ata4.00: configured for UDMA/133
ata4: EH complete
sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB)
sd 5:0:0:0: [sde] Write Protect is off
sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd c8/00:00:b7:f7:a0/00:00:00:00:00/ed tag 0 dma 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata3.00: status: { DRDY }
ata3: soft resetting link
ata3.00: configured for UDMA/133
ata3: EH complete
sd 4:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata4.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: port is slow to respond, please be patient (Status 0x80)
ata4: soft resetting link
ata4.00: configured for UDMA/133
ata4: EH complete
sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB)
sd 5:0:0:0: [sde] Write Protect is off
sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd c8/00:00:c7:26:a1/00:00:00:00:00/ed tag 0 dma 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata3.00: status: { DRDY }
ata3: soft resetting link
ata3.00: configured for UDMA/133
ata3: EH complete
sd 4:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd c8/00:00:ef:d9:a1/00:00:00:00:00/ed tag 0 dma 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata3.00: status: { DRDY }
ata3: soft resetting link
ata3.00: configured for UDMA/133
ata3: EH complete
sd 4:0:0:0: [sdd] 625142448 512-byte hardware sectors (320073 MB)
sd 4:0:0:0: [sdd] Write Protect is off
sd 4:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
usb 1-8: USB disconnect, address 4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata4.00: cmd b0/d8:00:00:4f:c2/00:00:00:00:00/00 tag 0
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: port is slow to respond, please be patient (Status 0x80)
ata4: soft resetting link
ata4.00: configured for UDMA/133
ata4: EH complete
sd 5:0:0:0: [sde] 976773168 512-byte hardware sectors (500108 MB)
sd 5:0:0:0: [sde] Write Protect is off
sd 5:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 5:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata4.00: limiting speed to UDMA/100:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata4.00: cmd b0/d8:00:00:4f:c2/00:00:00:00:00/00 tag 0
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: port is slow to respond, please be patient (Status 0x80)
ata4: device not ready (errno=-16), forcing hardreset
ata4: soft resetting link
ata4.00: revalidation failed (errno=-2)
ata4: failed to recover some devices, retrying in 5 secs
ata4: soft resetting link
ata4.00: configured for UDMA/100
ata4: EH complete
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata4.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
So the 2 SATA drives begin to spit errors when writing the DVD. This must
be a kernel bug...One other disk that was flaky in this box has survived
a full erase with SeaTools, a long test, and a Vista install on it.
Kernel is 2.6.24.4.
Any ideas ?
TIA
--
J.A. Magallon <jamagallon()ono!com> \ Software is like sex:
\ It's better when it's free
Mandriva Linux release 2008.1 (Cooker) for i586
Linux 2.6.23-jam05 (gcc 4.2.2 20071128 (4.2.2-2mdv2008.1)) SMP PREEMPT
next reply other threads:[~2008-04-08 15:13 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-04-08 15:13 J.A. Magallón [this message]
2008-04-08 15:59 ` DRDY errors again Jeff Garzik
2008-04-13 0:26 ` J.A. Magallón
2008-04-20 22:41 ` J.A. Magallón
2008-04-20 22:41 ` J.A. Magallón
2008-04-08 21:40 ` Bernd Eckenfels
2008-04-09 3:42 ` Philippe Troin
2008-04-13 0:22 ` J.A. Magallón
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080408171311.69441c8b@werewolf \
--to=jamagallon@ono.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.