From: mahakali <mahakali@orange.fr>
To: video4linux-list@redhat.com
Subject: Card Asus P7131 hybrid > no signal
Date: Mon, 28 Apr 2008 20:29:59 +0200 [thread overview]
Message-ID: <20080428182959.GA21773@orange.fr> (raw)
Hello !
I installed last week an Asus TV-Card P7131 Hybrid , I followed the
installation procedure described on an Ubuntu website.
On boot I get following messages :
saa7133[0]: i2c eeprom 00: 43 10 76 48 54 20 1c 00 43 43 a9 1c 55 d2 b2
92
saa7133[0]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d5 ff ff ff
ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 32 55 50 ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ff
saa7133[0]: i2c scan: found device @ 0x10 [???]
saa7133[0]: i2c scan: found device @ 0x96 [???]
saa7133[0]: i2c scan: found device @ 0xa0 [eeprom]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
tuner 1-004b: chip found @ 0x96 (saa7133[0])
tda8290 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
tda8290 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1f.5 to 64
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
w83627hf: Found W83627THF chip at 0x290
w83627hf w83627hf.656: Reading VID from GPIO5
i2c /dev entries driver
tda1004x: found firmware revision 20 -- ok
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfeaff000 irq 19 registered as card -1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
skge eth0: enabling interface
skge eth0: Link is up at 100 Mbps, full duplex, flow control both
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
ip6_tables: (C) 2000-2006 Netfilter Core Team
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0200000 [Radio]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
nvidia: module license 'NVIDIA' taints kernel.
NVRM: loading NVIDIA UNIX x86 Kernel Module 173.08 Tue Apr 1 23:46:53
PST 2008
NVRM: not using NVAGP, an AGPGART backend is loaded!
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xef
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
eth0: no IPv6 routers present
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7134 ALSA driver for DMA sound unloaded
Linux video capture interface: v2.00
saa7130/34: v4l2 driver version 0.2.14 loaded
saa7133[0]: found at 0000:02:0b.0, rev: 209, irq: 19, latency: 64, mmio:
0xfeaff000
saa7133[0]: subsystem: 1043:4876, board: ASUSTeK P7131 Hybrid
[card=112,insmod option]
saa7133[0]: board init: gpio is 0
saa7133[0]: gpio: mode=0x0000000 in=0x0000000 out=0x0000000 [pre-init]
input: saa7134 IR (ASUSTeK P7131 Hybri as /class/input/input6
tuner 1-004b: chip found @ 0x96 (saa7133[0])
tda8290 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
tda8290 1-004b: setting tuner address to 61
tuner 1-004b: type set to tda8290+75a
saa7133[0]:i2ceeprom 00: 43 10 76 48 54 20 1c 00 43 43 a9 1c 55 d2 b292
saa7133[0]:i2ceeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ffff
saa7133[0]:i2ceeprom 20: 01 40 01 02 03 01 01 03 08 ff 00 d5 ff ff ffff
saa7133[0]:i2ceeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff
saa7133[0]:i2ceeprom 40: ff 21 00 c2 96 10 03 32 55 50 ff ff ff ff ffff
saa7133[0]:i2ceeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff
saa7133[0]:i2ceeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff
saa7133[0]:i2ceeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ffff
saa7133[0]: i2c scan: found device @ 0x10 [???]
saa7133[0]: i2c scan: found device @ 0x96 [???]
saa7133[0]: i2c scan: found device @ 0xa0 [eeprom]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
saa7133[0]: registered device radio0
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision 20 -- ok
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0200000 [Radio]
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xfeaff000 irq 19 registered as card -1
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]/alsa: saa7133[0] at 0xfeaff000 irq 19 registered as card -1
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
saa7133[0]: gpio: mode=0x0200000 in=0x0000000 out=0x0000000 [Television]
I think, it is O.K or ???
I use tvtime, I launch it but I get following message : No signal ....
I try to find some channels, but i can find no one.
If I use tvtime-scanner, he finds some channels, puts theme in a channel
list, but I have no image, cannot watch TV ....
I tried following command :
>>> tune to:
>>> 570000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_AUTO:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_AUTO:HIERARCHY_NONE
WARNING: >>> tuning failed!!!
>>> tune to:
>>> 570000000:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_AUTO:FEC_AUTO:QAM_64:TRANSMISSION_MODE_8K:GUARD_INTERVAL_AUTO:HIERARCHY_NONE
>>> (tuning failed)
So my question is .... How can I make this card work ???
Thanks for your patience and help
mahakali
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
next reply other threads:[~2008-04-28 18:31 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-04-28 18:29 mahakali [this message]
[not found] ` <alpine.DEB.1.00.0804282103010.22981@sandbox.cz>
2008-04-29 19:21 ` Card Asus P7131 hybrid > no signal mahakali
2008-04-29 22:15 ` hermann pitton
2008-04-30 4:44 ` mahakali
2008-04-30 15:58 ` mahakali
2008-04-30 21:56 ` hermann pitton
2008-04-30 23:25 ` Mauro Carvalho Chehab
2008-05-01 2:25 ` hermann pitton
2008-05-04 20:50 ` Hartmut Hackmann
2008-05-04 23:01 ` hermann pitton
2008-05-01 5:58 ` mahakali
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080428182959.GA21773@orange.fr \
--to=mahakali@orange.fr \
--cc=video4linux-list@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.