From: Anton Vorontsov <avorontsov@ru.mvista.com>
To: Kumar Gala <galak@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Subject: [PATCH v2] powerpc/83xx: update mpc83xx_defconfig to support MPC8360E-RDK
Date: Wed, 11 Jun 2008 03:16:54 +0400 [thread overview]
Message-ID: <20080610231654.GA12300@polina.dev.rtsoft.ru> (raw)
In-Reply-To: <057C3E99-B1DC-49BF-B9A8-4C72D943E920@kernel.crashing.org>
This patch updates mpc83xx_defconfig to support MPC8360E-RDK board.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
---
On Tue, Jun 10, 2008 at 05:01:17PM -0500, Kumar Gala wrote:
[...]
> Can you look at refreshing this against my for-2.6.26 tree (its got an
> updated defconfig)
That's an idea. Cherry-picked the defconfig update commit, and here is
the patch on top.
I'm assuming that CONFIG_PCI=n + CONFIG_FB_OF build breakage fix will
be committed prior to this patch. If not, we'll have to enable the
CONFIG_PCI in the defconfig as a separate patch, since it will produce
unreadable changes again. (btw, is there any particular reason why PCI
is disabled?)
arch/powerpc/configs/mpc83xx_defconfig | 65 +++++++++++++++++++++++++++++--
1 files changed, 60 insertions(+), 5 deletions(-)
diff --git a/arch/powerpc/configs/mpc83xx_defconfig b/arch/powerpc/configs/mpc83xx_defconfig
index 4293c8b..d6a0052 100644
--- a/arch/powerpc/configs/mpc83xx_defconfig
+++ b/arch/powerpc/configs/mpc83xx_defconfig
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.26-rc5
-# Mon Jun 9 08:52:14 2008
+# Wed Jun 11 02:59:37 2008
#
# CONFIG_PPC64 is not set
@@ -38,6 +38,7 @@ CONFIG_ARCH_HAS_ILOG2_U32=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_GPIO=y
# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
CONFIG_PPC=y
CONFIG_EARLY_PRINTK=y
@@ -166,6 +167,7 @@ CONFIG_MPC832x_RDB=y
CONFIG_MPC834x_MDS=y
CONFIG_MPC834x_ITX=y
CONFIG_MPC836x_MDS=y
+CONFIG_MPC836x_RDK=y
CONFIG_MPC837x_MDS=y
CONFIG_MPC837x_RDB=y
CONFIG_SBC834x=y
@@ -241,6 +243,8 @@ CONFIG_ZONE_DMA=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_FSL_SOC=y
+CONFIG_FSL_LBC=y
+CONFIG_FSL_GTM=y
# CONFIG_PCI is not set
# CONFIG_PCI_DOMAINS is not set
# CONFIG_PCI_SYSCALL is not set
@@ -356,7 +360,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-# CONFIG_FW_LOADER is not set
+CONFIG_FW_LOADER=y
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
@@ -398,7 +402,7 @@ CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
-# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
@@ -438,6 +442,7 @@ CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_PLATFORM is not set
# CONFIG_MTD_ALAUDA is not set
CONFIG_MTD_NAND_FSL_ELBC=y
+CONFIG_MTD_NAND_FSL_UPM=y
# CONFIG_MTD_ONENAND is not set
#
@@ -445,6 +450,7 @@ CONFIG_MTD_NAND_FSL_ELBC=y
#
# CONFIG_MTD_UBI is not set
CONFIG_OF_DEVICE=y
+CONFIG_OF_GPIO=y
CONFIG_OF_I2C=y
# CONFIG_PARPORT is not set
CONFIG_BLK_DEV=y
@@ -636,7 +642,7 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=4
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_OF_PLATFORM is not set
-# CONFIG_SERIAL_QE is not set
+CONFIG_SERIAL_QE=y
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
@@ -655,6 +661,7 @@ CONFIG_I2C_CHARDEV=y
#
# I2C Hardware Bus support
#
+# CONFIG_I2C_GPIO is not set
CONFIG_I2C_MPC=y
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
@@ -672,6 +679,7 @@ CONFIG_I2C_MPC=y
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_TPS65010 is not set
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_SENSORS_TSL2550 is not set
# CONFIG_I2C_DEBUG_CORE is not set
@@ -679,6 +687,21 @@ CONFIG_I2C_MPC=y
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
# CONFIG_SPI is not set
+CONFIG_HAVE_GPIO_LIB=y
+
+#
+# GPIO Support
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# SPI GPIO expanders:
+#
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
CONFIG_HWMON=y
@@ -780,13 +803,43 @@ CONFIG_DAB=y
#
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
-# CONFIG_FB is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+CONFIG_FB_FOREIGN_ENDIAN=y
+CONFIG_FB_BOTH_ENDIAN=y
+# CONFIG_FB_BIG_ENDIAN is not set
+# CONFIG_FB_LITTLE_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+CONFIG_FB_MACMODES=y
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+CONFIG_FB_OF=y
+# CONFIG_FB_VGA16 is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_FSL_DIU is not set
+# CONFIG_FB_IBM_GXT4500 is not set
+# CONFIG_FB_VIRTUAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_LOGO is not set
#
# Sound
@@ -1012,8 +1065,10 @@ CONFIG_MSDOS_PARTITION=y
# CONFIG_SYSV68_PARTITION is not set
# CONFIG_NLS is not set
# CONFIG_DLM is not set
+CONFIG_UCC_SLOW=y
CONFIG_UCC_FAST=y
CONFIG_UCC=y
+CONFIG_QE_GPIO=y
#
# Library routines
--
1.5.5.4
next prev parent reply other threads:[~2008-06-10 23:16 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-04-29 18:59 [PATCH 0/6 v4] Few more patches for Kumar's powerpc.git Anton Vorontsov
2008-04-29 19:00 ` [PATCH 1/6] [POWERPC] sysdev: implement FSL GTM support Anton Vorontsov
2008-05-01 4:00 ` Kumar Gala
2008-05-01 11:43 ` Anton Vorontsov
2008-04-29 19:00 ` [PATCH 2/6] [POWERPC] QE: add support for QE USB clocks routing Anton Vorontsov
2008-04-29 19:57 ` Timur Tabi
2008-04-29 21:22 ` Anton Vorontsov
2008-04-29 19:00 ` [PATCH 3/6] [POWERPC] QE: prepare QE PIO code for GPIO LIB support Anton Vorontsov
2008-04-29 20:10 ` Timur Tabi
2008-04-29 19:00 ` [PATCH 4/6] [POWERPC] QE: implement support for the GPIO LIB API Anton Vorontsov
2008-04-29 20:29 ` Timur Tabi
2008-04-29 21:23 ` Anton Vorontsov
2008-04-29 21:29 ` Timur Tabi
2008-04-30 19:30 ` [PATCH v2 " Anton Vorontsov
2008-04-30 19:42 ` Timur Tabi
2008-04-30 22:47 ` Anton Vorontsov
2008-04-30 22:50 ` Timur Tabi
2008-04-30 22:59 ` Anton Vorontsov
2008-04-30 23:03 ` Timur Tabi
2008-04-30 23:24 ` Anton Vorontsov
2008-05-01 14:33 ` Timur Tabi
2008-05-01 14:33 ` Timur Tabi
2008-04-29 19:00 ` [PATCH 5/6] [POWERPC] 83xx: new board support: MPC8360E-RDK Anton Vorontsov
2008-06-10 15:55 ` Kumar Gala
2008-06-10 19:32 ` [PATCH] powerpc: 83xx: update mpc83xx_defconfig to support MPC8360E-RDK Anton Vorontsov
2008-06-10 22:01 ` Kumar Gala
2008-06-10 23:16 ` Anton Vorontsov [this message]
2008-06-11 12:47 ` [PATCH v3] powerpc/83xx: " Anton Vorontsov
2008-04-29 19:00 ` [PATCH 6/6] [POWERPC] booting-without-of: add FHCI USB, FSL MCU, FSL UPM and GPIO LEDs bindings Anton Vorontsov
2008-04-30 8:36 ` Wolfgang Grandegger
2008-04-30 11:16 ` Anton Vorontsov
2008-04-30 13:19 ` Wolfgang Grandegger
2008-04-30 14:07 ` Anton Vorontsov
2008-04-30 17:26 ` Wolfgang Grandegger
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20080610231654.GA12300@polina.dev.rtsoft.ru \
--to=avorontsov@ru.mvista.com \
--cc=galak@kernel.crashing.org \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.