From: Arkadiusz Miskiewicz <arekm@maven.pl>
To: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Cc: Linux-Scsi <linux-scsi@vger.kernel.org>,
AACRAID <AACRAID@adaptec.com>,
Achim Leubner <Achim_Leubner@adaptec.com>
Subject: Re: adaptec 3405 + 4 sas disks: synchronize_callback: synchronize failed, status = 226
Date: Mon, 14 Jul 2008 13:45:15 +0200 [thread overview]
Message-ID: <200807141345.16305.arekm@maven.pl> (raw)
In-Reply-To: <C9E18FB9-75B1-4768-B290-2E3C9370D68D@adaptec.com>
On Monday 14 July 2008, Mark Salyzyn wrote:
> 226 means CT_ERROR, a generic response to the CT_FLUSH_CACHE command
> to the controller when the action could not be performed.
>
> The action is to flush all the controller's cache to the targets in
> response to a SCSI SYNCHRONIZE_CACHE command. I expect that you are
> running with a degraded array, or incompatible drives?
It's in "Optimal" state and I have no idea which drives are "incompatible".
Is this list published somewhere (I was looking at 3405 download section at
adaptec.com)?
# ./arcconf64 getconfig 1 al
Controllers found: 1
----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
Controller Status : Optimal
Channel description : SAS/SATA
Controller Model : Adaptec 3405
Controller Serial Number : 8C0210064E7
Temperature : 46 C/ 114 F (Normal)
Installed memory : 128 MB
Copyback : Disabled
Background consistency check : Disabled
Automatic Failover : Enabled
Global task priority : High
Defunct disk drive count : 0
Logical devices/Failed/Degraded : 1/0/0
--------------------------------------------------------
Controller Version Information
--------------------------------------------------------
BIOS : 5.2-0 (15728)
Firmware : 5.2-0 (15728)
Driver : 1.1-5 (2449)
Boot Flash : 5.2-0 (15728)
--------------------------------------------------------
Controller Battery Information
--------------------------------------------------------
Status : Optimal
Over temperature : No
Capacity remaining : 99 percent
Time remaining (at current draw) : 3 days, 1 hours, 11 minutes
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : RAID
RAID level : 10
Status of logical device : Optimal
Size : 571392 MB
Stripe-unit size : 256 KB
Read-cache mode : Enabled
Write-cache mode : Enabled (write-back)
Write-cache setting : Enabled (write-back) when
protected by battery
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Group 0, Segment 0 : Present (0,0)
3LM4DRD200009842S4XD
Group 0, Segment 1 : Present (0,1)
3LM4DRDZ00009842RNGC
Group 1, Segment 0 : Present (0,2)
3LM4DS0P00009808RMV7
Group 1, Segment 1 : Present (0,3)
3LM48ABH00009842SXEE
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
Device #0
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SAS 3.0 Gb/s
Reported Channel,Device : 0,0
Reported Location : Enclosure 0, Slot 0
Reported ESD : 2,0
Vendor : SEAGATE
Model : ST3300655SS
Firmware : 0002
Serial number : 3LM4DRD200009842S4XD
World-wide name : 5000C5000A4B3558
Size : 286102 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
Device #1
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SAS 3.0 Gb/s
Reported Channel,Device : 0,1
Reported Location : Enclosure 0, Slot 1
Reported ESD : 2,0
Vendor : SEAGATE
Model : ST3300655SS
Firmware : 0002
Serial number : 3LM4DRDZ00009842RNGC
World-wide name : 5000C5000A4B3800
Size : 286102 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
Device #2
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SAS 3.0 Gb/s
Reported Channel,Device : 0,2
Reported Location : Enclosure 0, Slot 2
Reported ESD : 2,0
Vendor : SEAGATE
Model : ST3300655SS
Firmware : 0002
Serial number : 3LM4DS0P00009808RMV7
World-wide name : 5000C5000A4B3074
Size : 286102 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
Device #3
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SAS 3.0 Gb/s
Reported Channel,Device : 0,3
Reported Location : Enclosure 0, Slot 3
Reported ESD : 2,0
Vendor : SEAGATE
Model : ST3300655SS
Firmware : 0002
Serial number : 3LM48ABH00009842SXEE
World-wide name : 5000C5000A4B39B4
Size : 286102 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
Device #4
Device is an Enclosure services device
Reported Channel,Device : 2,0
Enclosure ID : 0
Type : SES2
Vendor : ADAPTEC
Model : Virtual SGPIO 0
Firmware : 0001
Status of Enclosure services device
Temperature : Normal
Command completed successfully.
>
> Make sure your drive and controller firmware is as up-to-date as
> possible.
Controller firmware is up to date. Disks firmware is 002 according to
arcconf, unfortunately seagate doesn't seem to publish firmware on their
site, so I don't know if it's old or new.
>
> Sincerely -- Mark Salyzyn
>
> On Jul 14, 2008, at 2:09 AM, Arkadiusz Miskiewicz wrote:
> > Hello,
> >
> > I'm running 2.6.24.3 kernel and I'm getting few error messages
> > comming from
> > aacraid driver. Hardware is adaptec 3405 running firmware 15728 + 4
> > SAS 300GB
> > harddisks configured in single raid10 array.
> >
> > [167674.161866] synchronize_callback: synchronize failed, status = 226
> > [168977.738031] synchronize_callback: synchronize failed, status = 226
> > [172180.752140] synchronize_callback: synchronize failed, status = 226
> > [177494.855145] synchronize_callback: synchronize failed, status = 226
> > [189594.477223] synchronize_callback: synchronize failed, status = 226
> > [191411.881236] synchronize_callback: synchronize failed, status = 226
> > [217130.596663] synchronize_callback: synchronize failed, status = 226
> > [219236.032362] synchronize_callback: synchronize failed, status = 226
> >
> > What does 226 mean and what does it indicate (serious problem?) ?
> >
> > ps. would be good if prefix was added to these messages to know
> > where these
> > come from
> > --
> > Arkadiusz Miśkiewicz PLD/Linux Team
> > arekm / maven.pl http://ftp.pld-linux.org/
--
Arkadiusz Miśkiewicz PLD/Linux Team
arekm / maven.pl http://ftp.pld-linux.org/
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
prev parent reply other threads:[~2008-07-14 11:45 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-07-14 6:09 adaptec 3405 + 4 sas disks: synchronize_callback: synchronize failed, status = 226 Arkadiusz Miskiewicz
2008-07-14 11:19 ` Mark Salyzyn
2008-07-14 11:45 ` Arkadiusz Miskiewicz [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200807141345.16305.arekm@maven.pl \
--to=arekm@maven.pl \
--cc=AACRAID@adaptec.com \
--cc=Achim_Leubner@adaptec.com \
--cc=Mark_Salyzyn@adaptec.com \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.