All of lore.kernel.org
 help / color / mirror / Atom feed
From: Andrew Morton <akpm@linux-foundation.org>
To: Kasper Sandberg <lkml@metanurb.dk>
Cc: LKML Mailinglist <linux-kernel@vger.kernel.org>,
	linux-usb@vger.kernel.org
Subject: Re: 2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB
Date: Fri, 31 Oct 2008 23:48:23 -0700	[thread overview]
Message-ID: <20081031234823.5064dd88.akpm@linux-foundation.org> (raw)
In-Reply-To: <1225344169.17253.43.camel@localhost>

(cc linux-usb)

On Thu, 30 Oct 2008 06:22:49 +0100 Kasper Sandberg <lkml@metanurb.dk> wrote:

> Hello..
> 
> I had to write an image to some usb flash drives, more specifically, 4GB
> kingston datatraveler sticks, and i figured, instead of doing just 1 at
> a time, i may aswell do 4, so i plugged in 4, and started 4 dd's of the
> images, to sdc, sdd, sde, sdf. However, i got usb disconnects and IO
> error messages from the kernel, these are at end of message. I had
> previously done ~5 writes of images to 5 other flash disks with no
> problem, but when i tried the next batch, those 4, it gave these errors.
> I killed the dd's, pulled them all out, and put in 1 at a time, and it
> worked perfectly.
> 
> unfortunately the first kernel messages have been flooded away. If you
> need .config and/or the boot kernel messages, i can reboot and get it.
> 
> this is on ICH9 ehci, from lspci:
> 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #4 (rev 02)
> 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #5 (rev 02)
> 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #6 (rev 02)
> 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
> Controller #2 (rev 02)
> 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #1 (rev 02)
> 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #2 (rev 02)
> 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
> Controller #3 (rev 02)
> 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
> Controller #1 (rev 02)
> 
> 
> and the messages:
> usb 8-6: new high speed USB device using ehci_hcd and address 17
> usb 8-6: configuration #1 chosen from 1 choice
> scsi24 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 17
> usb-storage: waiting for device to settle before scanning
> scsi 24:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0
> ANSI: 0 CCS
> sd 24:0:0:0: [sdc] 7936000 512-byte hardware sectors (4063 MB)
> sd 24:0:0:0: [sdc] Write Protect is off
> sd 24:0:0:0: [sdc] Mode Sense: 23 00 00 00
> sd 24:0:0:0: [sdc] Assuming drive cache: write through
> sd 24:0:0:0: [sdc] 7936000 512-byte hardware sectors (4063 MB)
> sd 24:0:0:0: [sdc] Write Protect is off
> sd 24:0:0:0: [sdc] Mode Sense: 23 00 00 00
> sd 24:0:0:0: [sdc] Assuming drive cache: write through
>  sdc: sdc1
> sd 24:0:0:0: [sdc] Attached SCSI removable disk
> usb-storage: device scan complete
> usb 8-5: new high speed USB device using ehci_hcd and address 18
> usb 8-5: configuration #1 chosen from 1 choice
> scsi25 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 18
> usb-storage: waiting for device to settle before scanning
> scsi 25:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0
> ANSI: 0 CCS
> sd 25:0:0:0: [sdd] 7936000 512-byte hardware sectors (4063 MB)
> sd 25:0:0:0: [sdd] Write Protect is off
> sd 25:0:0:0: [sdd] Mode Sense: 23 00 00 00
> sd 25:0:0:0: [sdd] Assuming drive cache: write through
> sd 25:0:0:0: [sdd] 7936000 512-byte hardware sectors (4063 MB)
> sd 25:0:0:0: [sdd] Write Protect is off
> sd 25:0:0:0: [sdd] Mode Sense: 23 00 00 00
> sd 25:0:0:0: [sdd] Assuming drive cache: write through
>  sdd: sdd1
> sd 25:0:0:0: [sdd] Attached SCSI removable disk
> usb-storage: device scan complete
> usb 7-2: new high speed USB device using ehci_hcd and address 6
> usb 7-2: configuration #1 chosen from 1 choice
> scsi26 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 6
> usb-storage: waiting for device to settle before scanning
> scsi 26:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0
> ANSI: 0 CCS
> sd 26:0:0:0: [sde] 7936000 512-byte hardware sectors (4063 MB)
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 23 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> sd 26:0:0:0: [sde] 7936000 512-byte hardware sectors (4063 MB)
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 23 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
>  sde: sde1
> sd 26:0:0:0: [sde] Attached SCSI removable disk
> usb-storage: device scan complete
> usb 7-1: new high speed USB device using ehci_hcd and address 7
> usb 7-1: configuration #1 chosen from 1 choice
> scsi27 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 7
> usb-storage: waiting for device to settle before scanning
> scsi 27:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0
> ANSI: 0 CCS
> sd 27:0:0:0: [sdf] 7936000 512-byte hardware sectors (4063 MB)
> sd 27:0:0:0: [sdf] Write Protect is off
> sd 27:0:0:0: [sdf] Mode Sense: 23 00 00 00
> sd 27:0:0:0: [sdf] Assuming drive cache: write through
> sd 27:0:0:0: [sdf] 7936000 512-byte hardware sectors (4063 MB)
> sd 27:0:0:0: [sdf] Write Protect is off
> sd 27:0:0:0: [sdf] Mode Sense: 23 00 00 00
> sd 27:0:0:0: [sdf] Assuming drive cache: write through
>  sdf: sdf1
> sd 27:0:0:0: [sdf] Attached SCSI removable disk
> usb-storage: device scan complete
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sde, sector 216960
> Buffer I/O error on device sde, logical block 27120
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 27121
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 27122
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 27123
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 27124
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 27125
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 27126
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 27127
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 27128
> lost page write due to I/O error on sde
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> end_request: I/O error, dev sde, sector 217200
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> __ratelimit: 97148 callbacks suppressed
> Buffer I/O error on device sde, logical block 124277
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124278
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124279
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124280
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124281
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124282
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124283
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124284
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124285
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 124286
> lost page write due to I/O error on sde
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> __ratelimit: 152257 callbacks suppressed
> Buffer I/O error on device sde, logical block 276544
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276545
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276546
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276547
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276548
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276549
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276550
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276551
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276552
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 276553
> lost page write due to I/O error on sde
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> __ratelimit: 170419 callbacks suppressed
> Buffer I/O error on device sde, logical block 446973
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446974
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446975
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446976
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446977
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446978
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446979
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446980
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446981
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 446982
> lost page write due to I/O error on sde
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> __ratelimit: 152214 callbacks suppressed
> Buffer I/O error on device sde, logical block 599197
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599198
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599199
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599200
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599201
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599202
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599203
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599204
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599205
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 599206
> lost page write due to I/O error on sde
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> __ratelimit: 165606 callbacks suppressed
> Buffer I/O error on device sde, logical block 764813
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764814
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764815
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764816
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764817
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764818
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764819
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764820
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764821
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 764822
> lost page write due to I/O error on sde
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> __ratelimit: 165555 callbacks suppressed
> Buffer I/O error on device sde, logical block 930378
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930379
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930380
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930381
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930382
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930383
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930384
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930385
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930386
> lost page write due to I/O error on sde
> Buffer I/O error on device sde, logical block 930387
> lost page write due to I/O error on sde
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-1: USB disconnect, address 7
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 8-5: USB disconnect, address 18
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: reset high speed USB device using ehci_hcd and address 6
> usb 7-2: USB disconnect, address 6
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x07 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> sd 26:0:0:0: [sde] READ CAPACITY failed
> sd 26:0:0:0: [sde] Result: hostbyte=0x01 driverbyte=0x00
> sd 26:0:0:0: [sde] Sense not available.
> sd 26:0:0:0: [sde] Write Protect is off
> sd 26:0:0:0: [sde] Mode Sense: 00 00 00 00
> sd 26:0:0:0: [sde] Assuming drive cache: write through
> usb 8-6: USB disconnect, address 17
> 
> 
> mvh.
> Kasper Sandberg
> 


  reply	other threads:[~2008-11-01  6:48 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2008-10-30  5:22 2.6.27.2 USB reset/IO Error problem when high load on ICH9 USB Kasper Sandberg
2008-11-01  6:48 ` Andrew Morton [this message]
2008-11-02  2:41   ` Alan Stern
2008-11-02  4:05   ` Greg KH
     [not found] <fa.PPRUdlhLAQMsAcsErf8qHTGwTPQ@ifi.uio.no>
2008-10-31  1:03 ` Robert Hancock
2008-11-01 11:07   ` Kasper Sandberg
2008-11-01 11:42     ` Adam Nielsen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20081031234823.5064dd88.akpm@linux-foundation.org \
    --to=akpm@linux-foundation.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=lkml@metanurb.dk \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.