From: Simon MORIN <simon.g.morin@gmail.com>
To: linux-dvb@linuxtv.org
Subject: [linux-dvb] WinTV HVR 1700 cannot scan (DVB-T)
Date: Wed, 26 Nov 2008 12:18:48 +0100 [thread overview]
Message-ID: <200811261218.49367.simon.g.morin@gmail.com> (raw)
[-- Attachment #1.1: Type: text/plain, Size: 8515 bytes --]
Hello everyone !
I have a problem with a WinTV HVR 1700
I installed the latest available driver via mercurial and the firmware (dvb-fe-
tda10048-1.0.fw).
The card seems to be well detected by its module (cx23885) as you can see in
the dmesg output.
I saw there [1] that some others firmware were used (v4l-cx23885-avcore-01.fw
and v4l-cx23885-enc.fw). I installed them, but I don't see when they are
loaded.
I am sure of the frequencies I used because I have successfully tested on the
same antenna, with the same frequencies with a WinTV Nova-T.
I do not see where the problem can come from.
[1] http://marc.info/?l=linux-dvb&m=120951119026705&w=2
Thank you very much for any help.
Simon MORIN
------
dmesg output :
Linux video capture interface: v2.00
cx23885 driver version 0.0.1 loaded
ACPI: PCI Interrupt 0000:0e:00.0[A] -> GSI 17 (level, low) -> IRQ 17
cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge type 885
cx23885[0]/0: cx23885_init_tsport(portno=2)
CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700
[card=8,autodetected]
cx23885[0]/0: cx23885_pci_quirks()
cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0
cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0
cx23885[0]/0: cx23885_reset()
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A]
cx23885[0]/0: cx23885_sram_channel_setup() 0x000104c0 <- 0x00000040
cx23885[0]/0: cx23885_sram_channel_setup() 0x000104d0 <- 0x00000b80
cx23885[0]/0: cx23885_sram_channel_setup() 0x000104e0 <- 0x000016c0
cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2]
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B]
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010580 <- 0x00005000
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010590 <- 0x000052f0
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105a0 <- 0x000055e0
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105b0 <- 0x000058d0
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105c0 <- 0x00005bc0
cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5]
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C]
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105e0 <- 0x00006000
cx23885[0]/0: cx23885_sram_channel_setup() 0x000105f0 <- 0x000062f0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010600 <- 0x000065e0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010610 <- 0x000068d0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010620 <- 0x00006bc0
cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9]
cx23885[0]: i2c scan: found device @ 0x10 [tda10048]
cx23885[0]: i2c scan: found device @ 0xa0 [eeprom]
cx23885[0]: i2c scan: found device @ 0x84 [tda8295]
cx25840' 2-0044: cx25 0-21 found @ 0x88 (cx23885[0])
cx23885[0]: i2c scan: found device @ 0x66 [???]
cx23885[0]: i2c scan: found device @ 0x88 [cx25837]
cx23885[0]: i2c scan: found device @ 0x98 [???]
tveeprom 0-0050: Hauppauge model 81519, rev B2E9, serial# 3473167
tveeprom 0-0050: MAC address is 00-0D-FE-34-FF-0F
tveeprom 0-0050: tuner model is Philips 18271_8295 (idx 149, type 54)
tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB
Digital (eeprom 0xf4)
tveeprom 0-0050: audio processor is CX23885 (idx 39)
tveeprom 0-0050: decoder processor is CX23885 (idx 33)
tveeprom 0-0050: has no radio
cx23885[0]: hauppauge eeprom: model=81519
cx23885_dvb_register() allocating 1 frontend(s)
cx23885[0]: cx23885 based dvb card
tda829x 1-0042: type set to tda8295
tda18271 1-0060: creating new instance
TDA18271HD/C1 detected @ 1-0060
DVB: registering new adapter (cx23885[0])
DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)...
cx23885_dev_checkrevision() Hardware revision = 0xb0
cx23885[0]/0: found at 0000:0e:00.0, rev: 2, irq: 17, latency: 0, mmio:
0xfde00000
PCI: Setting latency timer of device 0000:0e:00.0 to 64
tda10048_firmware_upload: waiting for firmware upload (dvb-fe-
tda10048-1.0.fw)...
firmware: requesting dvb-fe-tda10048-1.0.fw
tda10048_firmware_upload: firmware read 24878 bytes.
tda10048_firmware_upload: firmware uploading
tda10048_firmware_upload: firmware uploaded
-----
Modules loaded :
#$ modprobe -v cx23885
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/tveeprom.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/btcx-
risc.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/videobuf-core.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/dvb/dvb-
core/dvb-core.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/videobuf-dvb.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/videobuf-dma-sg.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/cx2341x.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/v4l2-
compat-ioctl32.ko
insmod /lib/modules/2.6.26-bpo.1-686-bigmem/kernel/drivers/media/video/v4l1-
compat.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/videodev.ko
insmod /lib/modules/2.6.26-bpo.1-686-
bigmem/kernel/drivers/media/video/cx23885/cx23885.ko debug=5 i2c_scan=1
[-- Attachment #1.2: Type: text/html, Size: 23695 bytes --]
[-- Attachment #2: Type: text/plain, Size: 150 bytes --]
_______________________________________________
linux-dvb mailing list
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
reply other threads:[~2008-11-26 11:19 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200811261218.49367.simon.g.morin@gmail.com \
--to=simon.g.morin@gmail.com \
--cc=linux-dvb@linuxtv.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.