From: bugme-daemon@bugzilla.kernel.org
To: linux-scsi@vger.kernel.org
Subject: [Bug 12120] [Block layer or SCSI] requests aborted too early during check_partition()
Date: Sat, 29 Nov 2008 11:29:55 -0800 (PST) [thread overview]
Message-ID: <20081129192955.3C53F10800F@picon.linux-foundation.org> (raw)
In-Reply-To: <bug-12120-11613@http.bugzilla.kernel.org/>
http://bugzilla.kernel.org/show_bug.cgi?id=12120
------- Comment #3 from anonymous@kernel-bugs.osdl.org 2008-11-29 11:29 -------
Reply-To: stefanr@s5r6.in-berlin.de
> It sounds like the device isn't being spun up, so commands which require
> media read are being failed with not ready. Could we get some traces to
> show this; just enable all tracing in the boot up sequence:
>
> echo 0xffffffff > /sys/module/scsi_mod/parameters/scsi_logging_level
OK, here is a log from a failing session in 2.6.28-rc6.
The firmware responds to everything without spinning the disk up,
until the first READ(10) is sent.
# spin disk down artificially with
# "modprobe -r firewire-sbp2" while manage_start_stop == 1
#
# then "modprobe firewire-sbp2"
Nov 29 19:57:05 stein Error handler scsi_eh_20 sleeping
Nov 29 19:57:05 stein scsi20 : SBP-2 IEEE-1394
Nov 29 19:57:06 stein firewire_sbp2: fw3.0: logged in to LUN 0000 (0 retries)
Nov 29 19:57:06 stein scsi 20:0:0:0: scsi scan: INQUIRY pass 1 length 36
Nov 29 19:57:06 stein scsi 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein scsi 20:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 36, queuecommand
0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein scsi 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein scsi 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein scsi 20:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
Nov 29 19:57:06 stein scsi 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein scsi 20:0:0:0: Notifying upper driver of completion
(result 0)
Nov 29 19:57:06 stein 0 sectors total, 36 bytes done.
Nov 29 19:57:06 stein scsi scan: INQUIRY successful with code 0x0
Nov 29 19:57:06 stein scsi 20:0:0:0: Direct-Access-RBC ST340083 2A
3.03 PQ: 0 ANSI: 4
Nov 29 19:57:06 stein sd 20:0:0:0: sd_attach
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_revalidate_disk
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
Nov 29 19:57:06 stein buffer = 0x00000000, bufflen = 0, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 0 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Read Capacity(10): 25 00 00 00 00 00 00
00 00 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 8, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Read Capacity(10): 25 00 00 00 00 00 00
00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 8 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] 781422768 512-byte hardware sectors:
(400 GB/372 GiB)
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 00 3f 00 04 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 4, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 00 3f 00 04 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 4 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Write Protect is off
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Mode Sense: 11 00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 04 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 4, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 04 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 4 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57986b0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 16 00
Nov 29 19:57:06 stein buffer = 0xf725f9d0, bufflen = 22, queuecommand
0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57986b0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 16 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 22 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_open
Nov 29 19:57:06 stein scsi_block_when_processing_errors: rtn: 1
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_revalidate_disk
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57984a0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
Nov 29 19:57:06 stein buffer = 0x00000000, bufflen = 0, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57984a0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 0 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf5798550
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Read Capacity(10): 25 00 00 00 00 00 00
00 00 00
Nov 29 19:57:06 stein buffer = 0xf725fd68, bufflen = 8, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf5798550 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Read Capacity(10): 25 00 00 00 00 00 00
00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 8 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] 781422768 512-byte hardware sectors:
(400 GB/372 GiB)
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf57981e0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 00 3f 00 04 00
Nov 29 19:57:06 stein buffer = 0xf725fed8, bufflen = 4, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf57981e0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 00 3f 00 04 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 4 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Write Protect is off
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Mode Sense: 11 00 00 00
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf5798600
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 04 00
Nov 29 19:57:06 stein buffer = 0xf725f918, bufflen = 4, queuecommand 0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf5798600 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 04 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 4 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: Send: 0xf5798ef0
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 16 00
Nov 29 19:57:06 stein buffer = 0xe5961b40, bufflen = 22, queuecommand
0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: Done: 0xf5798ef0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: CDB: Mode Sense(6): 1a 08 06 00 16 00
Nov 29 19:57:06 stein sd 20:0:0:0: scsi host busy 1 failed 0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
0)
Nov 29 19:57:06 stein 0 sectors total, 22 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
# partition scanning code gets into gears,
# issues very first READ command,
# now the failures start
Nov 29 19:57:06 stein sdd:<6>sd 20:0:0:0: [sdd] sd_init_command: block=0,
count=8
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] block=0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] reading 8/8 512 byte blocks.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Send: 0xf5798ef0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] CDB: Read(10): 28 00 00 00 00 00 00 00
08 00
Nov 29 19:57:06 stein buffer = 0xe5961b40, bufflen = 4096, queuecommand
0xf85fb980
Nov 29 19:57:06 stein leaving scsi_dispatch_cmnd()
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Done: 0xf5798ef0 FAILED
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] CDB: Read(10): 28 00 00 00 00 00 00 00
08 00
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Sense Key : Not Ready [current]
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Add. Sense: Logical unit not ready,
initializing command required
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] scsi host busy 1 failed 0
Nov 29 19:57:06 stein Waking error handler thread
Nov 29 19:57:06 stein Error handler scsi_eh_20 waking up
Nov 29 19:57:06 stein sd 20:0:0:0: scsi_eh_prt_fail_stats: cmds failed: 1,
cancel: 0
Nov 29 19:57:06 stein Total of 1 commands on 1 devices require eh work
Nov 29 19:57:06 stein scsi_eh_20: Sending START_UNIT to sdev: 0xe58fc7f0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Send: 0xf5798ef0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] CDB: Start/Stop Unit: 1b 00 00 00 01
00
Nov 29 19:57:06 stein buffer = 0x00000000, bufflen = 0, queuecommand 0xf85fb980
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Done: 0xf5798ef0 SUCCESS
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] CDB: Start/Stop Unit: 1b 00 00 00 01
00
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Unrecognized sense data (in hex):
Nov 29 19:57:06 stein 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Nov 29 19:57:06 stein 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Nov 29 19:57:06 stein Sense Key : No Sense [current]
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Add. Sense: No additional sense
information
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] scsi host busy 1 failed 1
Nov 29 19:57:06 stein scsi_send_eh_cmnd: scmd: f5798ef0, timeleft: 0
Nov 29 19:57:06 stein firewire_sbp2: fw3.0: sbp2_scsi_abort
Nov 29 19:57:06 stein scsi_eh_done scmd: f5798ef0 result: 20000
Nov 29 19:57:06 stein scsi_eh_20: START_UNIT failed to sdev: 0xe58fc7f0
Nov 29 19:57:06 stein scsi_eh_20: Sending BDR sdev: 0xe58fc7f0
Nov 29 19:57:06 stein scsi_eh_20: BDR failed sdev:0xe58fc7f0
Nov 29 19:57:06 stein scsi_eh_20: Sending target reset to target 0
Nov 29 19:57:06 stein scsi_eh_20: Target reset failed target: 0
Nov 29 19:57:06 stein scsi_eh_20: Sending BRST chan: 0
Nov 29 19:57:06 stein scsi_try_bus_reset: Snd Bus RST
Nov 29 19:57:06 stein scsi_eh_20: BRST failed chan: 0
Nov 29 19:57:06 stein scsi_eh_20: Sending HRST
Nov 29 19:57:06 stein scsi_try_host_reset: Snd Host RST
Nov 29 19:57:06 stein scsi_eh_20: HRST failed
Nov 29 19:57:06 stein sd 20:0:0:0: Device offlined - not ready after error
recovery
Nov 29 19:57:06 stein scsi_eh_20: flush finish cmd: f5798ef0
Nov 29 19:57:06 stein sd 20:0:0:0: Notifying upper driver of completion (result
2)
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein 8 sectors total, 0 bytes done.
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Result: hostbyte=DID_OK
driverbyte=DRIVER_OK,SUGGEST_OK
Nov 29 19:57:06 stein end_request: I/O error, dev sdd, sector 0
Nov 29 19:57:06 stein Buffer I/O error on device sdd, logical block 0
Nov 29 19:57:06 stein scsi_restart_operations: waking up host to restart
Nov 29 19:57:06 stein Error handler scsi_eh_20 sleeping
Nov 29 19:57:06 stein sd 20:0:0:0: rejecting I/O to offline device
Nov 29 19:57:06 stein Buffer I/O error on device sdd, logical block 0
Nov 29 19:57:06 stein ldm_validate_partition_table(): Disk read failed.
Nov 29 19:57:06 stein sd 20:0:0:0: rejecting I/O to offline device
Nov 29 19:57:06 stein Buffer I/O error on device sdd, logical block 0
Nov 29 19:57:06 stein sd 20:0:0:0: rejecting I/O to offline device
Nov 29 19:57:06 stein Buffer I/O error on device sdd, logical block 0
Nov 29 19:57:06 stein unable to read partition table
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_release
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] Attached SCSI disk
Nov 29 19:57:06 stein sg_alloc: dev=3
Nov 29 19:57:06 stein sd 20:0:0:0: Attached scsi generic sg3 type 14
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_open
Nov 29 19:57:06 stein scsi_block_when_processing_errors: rtn: 0
Nov 29 19:57:06 stein sd 20:0:0:0: [sdd] sd_open
Nov 29 19:57:06 stein scsi_block_when_processing_errors: rtn: 0
Nov 29 19:57:08 stein firewire_sbp2: fw3.0: reconnected to LUN 0000 (0 retries)
Nov 29 19:57:14 stein firewire_sbp2: fw3.0: reconnected to LUN 0000 (0 retries)
Nov 29 19:58:09 stein xinetd[4299]: START: imap2 pid=18913 from=192.168.0.42
Nov 29 19:58:09 stein imapd[18913]: imap service init from 192.168.0.42
Nov 29 19:58:09 stein imapd[18913]: Login user=stefan host=stein [192.168.0.42]
Nov 29 19:58:15 stein imapd[18914]: imap service init from 192.168.0.42
Nov 29 19:58:15 stein xinetd[4299]: START: imap2 pid=18914 from=192.168.0.42
Nov 29 19:58:15 stein imapd[18914]: Login user=stefan host=stein [192.168.0.42]
Nov 29 19:58:19 stein imapd[18913]: Logout user=stefan host=stein
[192.168.0.42]
Nov 29 19:58:19 stein xinetd[4299]: EXIT: imap2 status=0 pid=18913
duration=10(sec)
Nov 29 19:59:07 stein imapd[18914]: Logout user=stefan host=stein
[192.168.0.42]
Nov 29 19:59:07 stein xinetd[4299]: EXIT: imap2 status=0 pid=18914
duration=52(sec)
--
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.
next prev parent reply other threads:[~2008-11-29 19:30 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-11-29 13:19 [Bug 12120] New: [Block layer or SCSI] requests aborted too early during check_partition() bugme-daemon
2008-11-29 15:12 ` Stefan Richter
2008-11-29 18:35 ` James Bottomley
2008-11-29 15:12 ` [Bug 12120] " bugme-daemon
2008-11-29 18:36 ` bugme-daemon
2008-11-29 19:29 ` bugme-daemon [this message]
2008-11-29 19:32 ` bugme-daemon
2008-11-29 19:54 ` James Bottomley
2008-11-29 21:30 ` Stefan Richter
2008-11-29 21:45 ` Stefan Richter
2008-11-30 0:08 ` James Bottomley
2008-11-30 9:44 ` Stefan Richter
2008-11-30 16:16 ` James Bottomley
2008-11-29 19:55 ` bugme-daemon
2008-11-29 21:30 ` bugme-daemon
2008-11-29 21:45 ` bugme-daemon
2008-11-30 0:08 ` bugme-daemon
2008-11-30 9:44 ` bugme-daemon
2008-11-30 16:16 ` bugme-daemon
2008-12-04 1:15 ` bugme-daemon
2008-12-04 6:38 ` bugme-daemon
-- strict thread matches above, loose matches on Subject: below --
2008-12-03 21:49 2.6.28-rc7-git2: Reported regressions from 2.6.27 Rafael J. Wysocki
2008-12-03 21:58 ` [Bug #12120] [Block layer or SCSI] requests aborted too early during check_partition() Rafael J. Wysocki
2008-12-03 21:58 ` Rafael J. Wysocki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20081129192955.3C53F10800F@picon.linux-foundation.org \
--to=bugme-daemon@bugzilla.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.