[lm-sensors] [PATCH 1/3] hwmon: (k8temp) adapt cpuid handling,

[Andreas Herrmann <andreas.herrmann3@amd.com>]

We don't need to use northbridge based CPUID checking as the allowed
combinations of processors ensure that all processors in a multisocket
system have similar characteristics, e.g.

(1) provide temperature sensor interface (>=RevC && <RevF)
(2) are affected by erratum #141 (>=RevF)

Thus it is sufficient to check the revision of the boot CPU.

For "mixed silicon support" refer to
"Revision Guide for AMD Athlon 64 and AMD Opteron Processors" (RevA-E) and
"Revision Guide for AMD NPT Family 0Fh Processors" (RefF-G).

Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
---
 drivers/hwmon/k8temp.c |   26 +++++++++++---------------
 1 files changed, 11 insertions(+), 15 deletions(-)

diff --git a/drivers/hwmon/k8temp.c b/drivers/hwmon/k8temp.c
index 3b90384..be93387 100644
--- a/drivers/hwmon/k8temp.c
+++ b/drivers/hwmon/k8temp.c
@@ -31,10 +31,10 @@
 #include <linux/hwmon-sysfs.h>
 #include <linux/err.h>
 #include <linux/mutex.h>
+#include <asm/processor.h>
 
 #define TEMP_FROM_REG(val)	(((((val) >> 16) & 0xff) - 49) * 1000)
 #define REG_TEMP	0xe4
-#define REG_CPUID	0xfc
 #define SEL_PLACE	0x40
 #define SEL_CORE	0x04
 
@@ -48,7 +48,6 @@ struct k8temp_data {
 	/* registers values */
 	u8 sensorsp;		/* sensor presence bits - SEL_CORE & SEL_PLACE */
 	u32 temp[2][2];		/* core, place */
-	u8 fam;
 };
 
 static struct k8temp_data *k8temp_update_device(struct device *dev)
@@ -143,28 +142,25 @@ static int __devinit k8temp_probe(struct pci_dev *pdev,
 	int err;
 	u8 scfg;
 	u32 temp;
+	u8 model, stepping;
 	struct k8temp_data *data;
-	u32 cpuid = cpuid_eax(1);
-
-	/* this feature should be available since SH-C0 core */
-	if ((cpuid = 0xf40) || (cpuid = 0xf50) || (cpuid = 0xf51)) {
-		err = -ENODEV;
-		goto exit;
-	}
 
 	if (!(data = kzalloc(sizeof(struct k8temp_data), GFP_KERNEL))) {
 		err = -ENOMEM;
 		goto exit;
 	}
 
-	/* get real PCI based cpuid, prior revF of fam 0Fh, this reg is 0 */
-	pci_read_config_dword(pdev, REG_CPUID, &cpuid);
-
-	data->fam = (cpuid & 0x00000f00) >> 8;
-	data->fam += (cpuid & 0x0ff00000) >> 20;
+	model = boot_cpu_data.x86_model;
+	stepping = boot_cpu_data.x86_mask;
 
-	switch (data->fam) {
+	switch (boot_cpu_data.x86) {
 	case 0xf:
+		/* feature available since SH-C0, exclude older revisions */
+		if (((model = 4) && (stepping = 0)) ||
+		    ((model = 5) && ((stepping = 0) || (stepping = 1)))) {
+			err = -ENODEV;
+			goto exit;
+		}
 		dev_warn(&pdev->dev, "Temperature readouts might be wrong"
 					" - check errata #141\n");
 		break;
-- 
1.6.0.4




_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors