From: Matteo Croce <technoboy85-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
To: Jiri Kosina <jkosina-AlSwsSmVLrQ@public.gmane.org>
Cc: linux-input-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Western Digital HDD Leds
Date: Tue, 23 Dec 2008 01:19:09 +0100 [thread overview]
Message-ID: <200812230119.10231.technoboy85@gmail.com> (raw)
Hi,
I have a Western Digital usb HDD, it has some nice LEDs to show the disk
usage, but sadly they works only with Windows.
This is the syslog:
usb 1-1: new high speed USB device using ehci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
input: Western Digital External HDD as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1:1.1/input/input7
generic-usb 0003:1058:0705.0002: input,hidraw0: USB HID v1.10 Device [Western Digital External HDD ] on usb-0000:00:1d.7-1/input1
Initializing USB Mass Storage driver...
scsi3 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 3:0:0:0: Direct-Access WD 3200BEV External 1.75 PQ: 0 ANSI: 4
sd 3:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sd 3:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
so it seems that the LEDs are an USB HID device, and udev creates /dev/hidraw0
lsusb -n says:
Bus 001 Device 003: ID 1058:0705 Western Digital Technologies, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1058 Western Digital Technologies, Inc.
idProduct 0x0705
bcdDevice 1.75
iManufacturer 1 Western Digital
iProduct 2 External HDD
iSerial 3 57442D575848393038343538303037
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 57
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 3 Human Interface Device
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 5 WD HID INTERFACE
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.10
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 33
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 6
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
note the lines:
bInterfaceClass 8 Mass Storage
bInterfaceClass 3 Human Interface Device
My question now is: how can we make the LEDs configurable by Linux?
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
reply other threads:[~2008-12-23 0:19 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200812230119.10231.technoboy85@gmail.com \
--to=technoboy85-re5jqeeqqe8avxtiumwx3w@public.gmane.org \
--cc=jkosina-AlSwsSmVLrQ@public.gmane.org \
--cc=linux-input-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.