From: Grant Likely <grant.likely@secretlab.ca>
To: linuxppc-dev@ozlabs.org
Subject: [RFC 2/2] powerpc/5200: add LocalPlus bus FIFO device driver
Date: Fri, 06 Mar 2009 14:13:01 -0700 [thread overview]
Message-ID: <20090306211237.24316.86323.stgit@localhost.localdomain> (raw)
In-Reply-To: <20090306211123.24316.80764.stgit@localhost.localdomain>
From: Grant Likely <grant.likely@secretlab.ca>
This is a driver for the LocalPlus bus FIFO device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
---
This also isn't complete, but I wanted to get it out there and reviewed
before I commit to the design. Comments appreciated.
g.
arch/powerpc/include/asm/mpc52xx.h | 11 +
arch/powerpc/platforms/52xx/Kconfig | 4
arch/powerpc/platforms/52xx/Makefile | 1
arch/powerpc/platforms/52xx/mpc52xx_lpbfifo.c | 282 +++++++++++++++++++++++++
4 files changed, 298 insertions(+), 0 deletions(-)
create mode 100644 arch/powerpc/platforms/52xx/mpc52xx_lpbfifo.c
diff --git a/arch/powerpc/include/asm/mpc52xx.h b/arch/powerpc/include/asm/mpc52xx.h
index 8273357..7ec34ea 100644
--- a/arch/powerpc/include/asm/mpc52xx.h
+++ b/arch/powerpc/include/asm/mpc52xx.h
@@ -282,6 +282,17 @@ extern int mpc52xx_gpt_start_timer(struct mpc52xx_gpt_priv *gpt, int period,
int continuous);
extern void mpc52xx_gpt_stop_timer(struct mpc52xx_gpt_priv *gpt);
+/* mpc52xx_lpbfifo.c */
+extern int mpc52xx_lpbfifo_write(void *src, unsigned int cs,
+ size_t offset, size_t size, int flags,
+ void (*callback)(void *, size_t, int),
+ void *callback_data);
+extern int mpc52xx_lpbfifo_read(void *dest, unsigned int cs,
+ size_t offset, size_t size, int flags,
+ void (*callback)(void *, size_t, int),
+ void *callback_data);
+extern void mpc52xx_lpbfifo_abort(void *callback_data);
+
/* mpc52xx_pic.c */
extern void mpc52xx_init_irq(void);
extern unsigned int mpc52xx_get_irq(void);
diff --git a/arch/powerpc/platforms/52xx/Kconfig b/arch/powerpc/platforms/52xx/Kconfig
index 0465e5b..f117e23 100644
--- a/arch/powerpc/platforms/52xx/Kconfig
+++ b/arch/powerpc/platforms/52xx/Kconfig
@@ -61,3 +61,7 @@ config PPC_MPC5200_GPIO
select GENERIC_GPIO
help
Enable gpiolib support for mpc5200 based boards
+
+config PPC_MPC5200_LPBFIFO
+ tristate "MPC5200 LocalPlus bus FIFO driver"
+ depends on PPC_MPC52xx
diff --git a/arch/powerpc/platforms/52xx/Makefile b/arch/powerpc/platforms/52xx/Makefile
index bfd4f52..2bc8cd0 100644
--- a/arch/powerpc/platforms/52xx/Makefile
+++ b/arch/powerpc/platforms/52xx/Makefile
@@ -15,3 +15,4 @@ ifeq ($(CONFIG_PPC_LITE5200),y)
endif
obj-$(CONFIG_PPC_MPC5200_GPIO) += mpc52xx_gpio.o
+obj-$(CONFIG_PPC_MPC5200_LPBFIFO) += mpc52xx_lpbfifo.o
diff --git a/arch/powerpc/platforms/52xx/mpc52xx_lpbfifo.c b/arch/powerpc/platforms/52xx/mpc52xx_lpbfifo.c
new file mode 100644
index 0000000..b00d763
--- /dev/null
+++ b/arch/powerpc/platforms/52xx/mpc52xx_lpbfifo.c
@@ -0,0 +1,282 @@
+/*
+ * LocalPlus Bus FIFO driver for the Freescale MPC52xx.
+ *
+ * Copyright (C) 2009 Secret Lab Technologies Ltd.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ *
+ */
+
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/spinlock.h>
+#include <asm/io.h>
+#include <asm/prom.h>
+#include <asm/mpc52xx.h>
+
+MODULE_AUTHOR("Grant Likely <grant.likely@secretlab.ca>");
+MODULE_DESCRIPTION("MPC5200 LocalPlus FIFO device driver");
+MODULE_LICENSE("GPL");
+
+#define LPBFIFO_REG_PACKET_SIZE (0x00)
+#define LPBFIFO_REG_START_ADDRESS (0x04)
+#define LPBFIFO_REG_CONTROL (0x08)
+#define LPBFIFO_REG_ENABLE (0x0C)
+#define LPBFIFO_REG_BYTES_DONE_STATUS (0x14)
+#define LPBFIFO_REG_FIFO_DATA (0x40)
+#define LPBFIFO_REG_FIFO_STATUS (0x44)
+#define LPBFIFO_REG_FIFO_CONTROL (0x48)
+#define LPBFIFO_REG_FIFO_ALARM (0x4C)
+
+struct mpc52xx_lpbfifo {
+ struct device *dev;
+ void __iomem *regs;
+ int irq;
+ spinlock_t lock;
+
+ /* Current transfer data */
+ void *data;
+ int cs;
+ size_t offset;
+ size_t size;
+ size_t remaining;
+ void (*callback)(void *, size_t, int);
+ void *callback_data;
+};
+
+/* The MPC5200 has only one fifo, so only need one instance structure */
+static struct mpc52xx_lpbfifo lpbfifo;
+
+/**
+ * mpc52xx_lpbfifo_kick - Trigger the next block of data to be transfered
+ */
+static void mpc52xx_lpbfifo_kick(void)
+{
+ size_t transfer_size = lpbfifo.remaining;
+
+ /* While the FIFO can be setup for transfer sizes as large as 16M-1,
+ * the FIFO itself is only 512 bytes deep and it does not generate
+ * interrupts for FIFO full events (only transfer complete will
+ * raise an IRQ). Therefore when not using Bestcomm to drive the
+ * FIFO it needs to either be polled, or transfers need to constrained
+ * to the size of the fifo.
+ *
+ * Here we choose to restrict the size of the transfer
+ */
+ if (transfer_size > 512)
+ transfer_size = 512;
+
+ /* Set and clear the reset bits; is good practice in User Manual */
+ out_be32(lpbfifo.regs + LPBFIFO_REG_ENABLE, 0x01010000);
+ out_be32(lpbfifo.regs + LPBFIFO_REG_ENABLE, 0x00000301);
+
+ /* Set transfer size, width, chip select and READ mode */
+ out_be32(lpbfifo.regs + LPBFIFO_REG_PACKET_SIZE, transfer_size);
+ out_be32(lpbfifo.regs + LPBFIFO_REG_CONTROL,
+ lpbfifo.cs << 24 | 0x00010008);
+
+ /* Kick it off */
+ out_8(lpbfifo.regs + LPBFIFO_REG_PACKET_SIZE, 0x01);
+}
+
+/**
+ * mpc52xx_lpbfifo_irq - IRQ handler for LPB FIFO
+ */
+static irqreturn_t mpc52xx_lpbfifo_irq(int irq, void *dev_id)
+{
+ u8 status = in_8(lpbfifo.regs + LPBFIFO_REG_BYTES_DONE_STATUS);
+ u32 *data;
+ int count, i;
+ void (*callback)(void *, size_t, int);
+ void *callback_data;
+
+ spin_lock(&lpbfifo.lock);
+
+ if (status & 0x10) { /* check abort bit */
+ out_be32(lpbfifo.regs + LPBFIFO_REG_ENABLE, 0x01010000);
+ } else if (status & 0x01) { /* check transaction done bit */
+ /* Read result from hardware */
+ count = in_be32(lpbfifo.regs + LPBFIFO_REG_BYTES_DONE_STATUS);
+ count &= 0x00ffffff;
+
+ data = lpbfifo.data;
+ for (i = 0; i < count; i += 4)
+ *data++ = in_be32(lpbfifo.regs + LPBFIFO_REG_FIFO_DATA);
+
+ /* Update transfer position and count */
+ lpbfifo.remaining -= count;
+ lpbfifo.offset += count;
+ lpbfifo.data += count;
+
+ /* Clear the IRQ */
+ out_8(lpbfifo.regs + LPBFIFO_REG_BYTES_DONE_STATUS, 0x01);
+
+ if (lpbfifo.remaining) {
+ /* More work to do. Kick of the next block and exit */
+ mpc52xx_lpbfifo_kick();
+ spin_unlock(&lpbfifo.lock);
+ return IRQ_HANDLED;
+ }
+ }
+
+ /* Mark the FIFO as idle */
+ lpbfifo.data = NULL;
+ callback = lpbfifo.callback;
+ callback_data = lpbfifo.callback_data;
+ count = lpbfifo.size - lpbfifo.remaining;
+
+ /* Release the lock before calling out to the callback. */
+ spin_unlock(&lpbfifo.lock);
+
+ /* If control reaches this point then the transfer is finished,
+ * either normal completion or due to abort */
+ callback(callback_data, count, (status & 0x10) != 0);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * mpc52xx_lpbfifo_read - Initiate an LPB fifo READ transaction
+ * @data: location to copy data into
+ * @cs: LocalPlus bus chip select number for transfer
+ * @offset: Location of data to read as an offset from the CS base address
+ * @size: Size of transfer in bytes
+ * @callback: Callback function for FIFO events. Will be called when the
+ * FIFO high watermark is reached, when the transfer finishes,
+ * and if a FIFO error occurs.
+ * @data: Private data pointer to be passed to callback function.
+ */
+int mpc52xx_lpbfifo_read(void *dest, unsigned int cs,
+ size_t offset, size_t size, int mode_flags,
+ void (*callback)(void *, size_t, int),
+ void *callback_data)
+{
+ int rc = -EBUSY;
+ unsigned long flags;
+
+ if (!lpbfifo.regs)
+ return -ENODEV;
+
+ spin_lock_irqsave(&lpbfifo.lock, flags);
+ /* If the data pointer is already set then a transfer is in progress */
+ if (lpbfifo.data)
+ goto out;
+
+ /* Setup the transfer */
+ lpbfifo.data = dest;
+ lpbfifo.cs = cs;
+ lpbfifo.offset = offset;
+ lpbfifo.remaining = lpbfifo.size = size;
+ lpbfifo.callback = callback;
+ lpbfifo.callback_data = callback_data;
+
+ mpc52xx_lpbfifo_kick();
+ rc = 0;
+
+ out:
+ spin_unlock_irqrestore(&lpbfifo.lock, flags);
+ return rc;
+}
+EXPORT_SYMBOL(mpc52xx_lpbfifo_read);
+
+void mpc52xx_lpbfifo_abort(void *callback_data)
+{
+ unsigned long flags;
+
+ if (lpbfifo.callback_data != callback_data)
+ return;
+
+ spin_lock_irqsave(&lpbfifo.lock, flags);
+ /* Put it into reset and clear the state */
+ out_be32(lpbfifo.regs + LPBFIFO_REG_ENABLE, 0x01010000);
+ lpbfifo.data = NULL;
+ spin_unlock_irqrestore(&lpbfifo.lock, flags);
+}
+EXPORT_SYMBOL(mpc52xx_lpbfifo_abort);
+
+static int __devinit
+mpc52xx_lpbfifo_probe(struct of_device *op, const struct of_device_id *match)
+{
+ int rc;
+
+ if (lpbfifo.dev != NULL)
+ return -ENOSPC;
+
+ lpbfifo.regs = of_iomap(op->node, 0);
+ if (!lpbfifo.regs)
+ return -ENOMEM;
+
+ lpbfifo.irq = irq_of_parse_and_map(op->node, 0);
+ if (!lpbfifo.irq) {
+ lpbfifo.regs = NULL;
+ iounmap(lpbfifo.regs);
+ return -ENOMEM;
+ }
+
+ spin_lock_init(&lpbfifo.lock);
+
+ /* Put FIFO into reset */
+ out_be32(lpbfifo.regs + LPBFIFO_REG_ENABLE, 0x01010000);
+
+ /* Register the interrupt handler */
+ rc = request_irq(lpbfifo.irq, mpc52xx_lpbfifo_irq, 0,
+ "mpc52xx-lpbfifo", &lpbfifo);
+ if (rc) {
+ pr_err("request_irq() failed. rc=%i\n", rc);
+ lpbfifo.regs = NULL;
+ free_irq(lpbfifo.irq, &lpbfifo);
+ iounmap(lpbfifo.regs);
+ }
+
+ lpbfifo.dev = &op->dev;
+ pr_info("LPB FIFO ready; regs=%p irq=%i\n", lpbfifo.regs, lpbfifo.irq);
+ return 0;
+}
+
+
+static int __devexit mpc52xx_lpbfifo_remove(struct of_device *op)
+{
+ if (lpbfifo.dev == &op->dev) {
+ /* Put FIFO in reset */
+ out_be32(lpbfifo.regs + LPBFIFO_REG_ENABLE, 0x01010000);
+ lpbfifo.regs = NULL;
+ free_irq(lpbfifo.irq, &lpbfifo);
+ iounmap(lpbfifo.regs);
+ lpbfifo.dev = NULL;
+ }
+ return 0;
+}
+
+static struct of_device_id mpc52xx_lpbfifo_match[] __devinitdata = {
+ { .compatible = "fsl,mpc5200-lpbfifo", },
+ {},
+};
+
+static struct of_platform_driver mpc52xx_lpbfifo_driver = {
+ .owner = THIS_MODULE,
+ .name = "mpc52xx-lpbfifo",
+ .match_table = mpc52xx_lpbfifo_match,
+ .probe = mpc52xx_lpbfifo_probe,
+ .remove = __devexit_p(mpc52xx_lpbfifo_remove),
+};
+
+/***********************************************************************
+ * Module init/exit
+ */
+static int __init mpc52xx_lpbfifo_init(void)
+{
+ pr_debug("Registering LocalPlus bus FIFO driver\n");
+ return of_register_platform_driver(&mpc52xx_lpbfifo_driver);
+}
+module_init(mpc52xx_lpbfifo_init);
+
+static void __exit mpc52xx_lpbfifo_exit(void)
+{
+ pr_debug("Unregistering LocalPlus bus FIFO driver\n");
+ of_unregister_platform_driver(&mpc52xx_lpbfifo_driver);
+}
+module_exit(mpc52xx_lpbfifo_exit);
next prev parent reply other threads:[~2009-03-06 21:13 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-03-06 21:12 [RFC 1/2] powerpc/5200: add general purpose timer API for the MPC5200 Grant Likely
2009-03-06 21:13 ` Grant Likely [this message]
2009-03-06 21:29 ` Jon Smirl
2009-03-06 21:39 ` Grant Likely
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090306211237.24316.86323.stgit@localhost.localdomain \
--to=grant.likely@secretlab.ca \
--cc=linuxppc-dev@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.