From: Divy Le Ray <divy@chelsio.com>
To: davem@davemloft.net
Cc: netdev@vger.kernel.org, linux-kernel@vger.kernel.org,
swise@opengridcomputing.com
Subject: [PATCH net-next 2/2] cxgb3: Add Aeluros 2020 phy support
Date: Fri, 29 May 2009 00:58:29 -0700 [thread overview]
Message-ID: <20090529075829.30669.41488.stgit@speedy5> (raw)
In-Reply-To: <20090529075823.30669.28885.stgit@speedy5>
From: Divy Le Ray <divy@chelsio.com>
Add support for the AEL2020 phy.
Add PCI IDs of the boards using this phy.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
---
drivers/net/cxgb3/ael1002.c | 823 +++++++++++++++++++++++++++++++++++++---
drivers/net/cxgb3/common.h | 2
drivers/net/cxgb3/cxgb3_main.c | 2
drivers/net/cxgb3/t3_hw.c | 7
4 files changed, 769 insertions(+), 65 deletions(-)
diff --git a/drivers/net/cxgb3/ael1002.c b/drivers/net/cxgb3/ael1002.c
index df1f585..9fe008e 100644
--- a/drivers/net/cxgb3/ael1002.c
+++ b/drivers/net/cxgb3/ael1002.c
@@ -44,12 +44,33 @@ enum {
AEL_I2C_STAT = 0xc30c,
AEL2005_GPIO_CTRL = 0xc214,
AEL2005_GPIO_STAT = 0xc215,
+
+ AEL2020_GPIO_INTR = 0xc103, /* Latch High (LH) */
+ AEL2020_GPIO_CTRL = 0xc108, /* Store Clear (SC) */
+ AEL2020_GPIO_STAT = 0xc10c, /* Read Only (RO) */
+ AEL2020_GPIO_CFG = 0xc110, /* Read Write (RW) */
+
+ AEL2020_GPIO_SDA = 0, /* IN: i2c serial data */
+ AEL2020_GPIO_MODDET = 1, /* IN: Module Detect */
+ AEL2020_GPIO_0 = 3, /* IN: unassigned */
+ AEL2020_GPIO_1 = 2, /* OUT: unassigned */
+ AEL2020_GPIO_LSTAT = AEL2020_GPIO_1, /* wired to link status LED */
};
enum { edc_none, edc_sr, edc_twinax };
/* PHY module I2C device address */
-#define MODULE_DEV_ADDR 0xa0
+enum {
+ MODULE_DEV_ADDR = 0xa0,
+ SFF_DEV_ADDR = 0xa2,
+};
+
+/* PHY transceiver type */
+enum {
+ phy_transtype_unknown = 0,
+ phy_transtype_sfp = 3,
+ phy_transtype_xfp = 6,
+};
#define AEL2005_MODDET_IRQ 4
@@ -86,6 +107,37 @@ static void ael100x_txon(struct cphy *phy)
msleep(30);
}
+/*
+ * Read an 8-bit word from a device attached to the PHY's i2c bus.
+ */
+static int ael_i2c_rd(struct cphy *phy, int dev_addr, int word_addr)
+{
+ int i, err;
+ unsigned int stat, data;
+
+ err = t3_mdio_write(phy, MDIO_MMD_PMAPMD, AEL_I2C_CTRL,
+ (dev_addr << 8) | (1 << 8) | word_addr);
+ if (err)
+ return err;
+
+ for (i = 0; i < 200; i++) {
+ msleep(1);
+ err = t3_mdio_read(phy, MDIO_MMD_PMAPMD, AEL_I2C_STAT, &stat);
+ if (err)
+ return err;
+ if ((stat & 3) == 1) {
+ err = t3_mdio_read(phy, MDIO_MMD_PMAPMD, AEL_I2C_DATA,
+ &data);
+ if (err)
+ return err;
+ return data >> 8;
+ }
+ }
+ CH_WARN(phy->adapter, "PHY %u i2c read of dev.addr %#x.%#x timed out\n",
+ phy->mdio.prtad, dev_addr, word_addr);
+ return -ETIMEDOUT;
+}
+
static int ael1002_power_down(struct cphy *phy, int enable)
{
int err;
@@ -199,6 +251,51 @@ int t3_ael1006_phy_prep(struct cphy *phy, struct adapter *adapter,
return 0;
}
+/*
+ * Decode our module type.
+ */
+static int ael2xxx_get_module_type(struct cphy *phy, int delay_ms)
+{
+ int v;
+
+ if (delay_ms)
+ msleep(delay_ms);
+
+ /* see SFF-8472 for below */
+ v = ael_i2c_rd(phy, MODULE_DEV_ADDR, 3);
+ if (v < 0)
+ return v;
+
+ if (v == 0x10)
+ return phy_modtype_sr;
+ if (v == 0x20)
+ return phy_modtype_lr;
+ if (v == 0x40)
+ return phy_modtype_lrm;
+
+ v = ael_i2c_rd(phy, MODULE_DEV_ADDR, 6);
+ if (v < 0)
+ return v;
+ if (v != 4)
+ goto unknown;
+
+ v = ael_i2c_rd(phy, MODULE_DEV_ADDR, 10);
+ if (v < 0)
+ return v;
+
+ if (v & 0x80) {
+ v = ael_i2c_rd(phy, MODULE_DEV_ADDR, 0x12);
+ if (v < 0)
+ return v;
+ return v > 10 ? phy_modtype_twinax_long : phy_modtype_twinax;
+ }
+unknown:
+ return phy_modtype_unknown;
+}
+
+/*
+ * Code to support the Aeluros/NetLogic 2005 10Gb PHY.
+ */
static int ael2005_setup_sr_edc(struct cphy *phy)
{
static struct reg_val regs[] = {
@@ -893,35 +990,7 @@ static int ael2005_setup_twinax_edc(struct cphy *phy, int modtype)
return err;
}
-static int ael2005_i2c_rd(struct cphy *phy, int dev_addr, int word_addr)
-{
- int i, err;
- unsigned int stat, data;
-
- err = t3_mdio_write(phy, MDIO_MMD_PMAPMD, AEL_I2C_CTRL,
- (dev_addr << 8) | (1 << 8) | word_addr);
- if (err)
- return err;
-
- for (i = 0; i < 5; i++) {
- msleep(1);
- err = t3_mdio_read(phy, MDIO_MMD_PMAPMD, AEL_I2C_STAT, &stat);
- if (err)
- return err;
- if ((stat & 3) == 1) {
- err = t3_mdio_read(phy, MDIO_MMD_PMAPMD, AEL_I2C_DATA,
- &data);
- if (err)
- return err;
- return data >> 8;
- }
- }
- CH_WARN(phy->adapter, "PHY %u I2C read of addr %u timed out\n",
- phy->mdio.prtad, word_addr);
- return -ETIMEDOUT;
-}
-
-static int get_module_type(struct cphy *phy, int delay_ms)
+static int ael2005_get_module_type(struct cphy *phy, int delay_ms)
{
int v;
unsigned int stat;
@@ -933,39 +1002,7 @@ static int get_module_type(struct cphy *phy, int delay_ms)
if (stat & (1 << 8)) /* module absent */
return phy_modtype_none;
- if (delay_ms)
- msleep(delay_ms);
-
- /* see SFF-8472 for below */
- v = ael2005_i2c_rd(phy, MODULE_DEV_ADDR, 3);
- if (v < 0)
- return v;
-
- if (v == 0x10)
- return phy_modtype_sr;
- if (v == 0x20)
- return phy_modtype_lr;
- if (v == 0x40)
- return phy_modtype_lrm;
-
- v = ael2005_i2c_rd(phy, MODULE_DEV_ADDR, 6);
- if (v < 0)
- return v;
- if (v != 4)
- goto unknown;
-
- v = ael2005_i2c_rd(phy, MODULE_DEV_ADDR, 10);
- if (v < 0)
- return v;
-
- if (v & 0x80) {
- v = ael2005_i2c_rd(phy, MODULE_DEV_ADDR, 0x12);
- if (v < 0)
- return v;
- return v > 10 ? phy_modtype_twinax_long : phy_modtype_twinax;
- }
-unknown:
- return phy_modtype_unknown;
+ return ael2xxx_get_module_type(phy, delay_ms);
}
static int ael2005_intr_enable(struct cphy *phy)
@@ -1024,7 +1061,7 @@ static int ael2005_reset(struct cphy *phy, int wait)
msleep(50);
- err = get_module_type(phy, 0);
+ err = ael2005_get_module_type(phy, 0);
if (err < 0)
return err;
phy->modtype = err;
@@ -1062,7 +1099,7 @@ static int ael2005_intr_handler(struct cphy *phy)
return ret;
/* modules have max 300 ms init time after hot plug */
- ret = get_module_type(phy, 300);
+ ret = ael2005_get_module_type(phy, 300);
if (ret < 0)
return ret;
@@ -1113,6 +1150,662 @@ int t3_ael2005_phy_prep(struct cphy *phy, struct adapter *adapter,
}
/*
+ * Setup EDC and other parameters for operation with an optical module.
+ */
+static int ael2020_setup_sr_edc(struct cphy *phy)
+{
+ static struct reg_val regs[] = {
+ /* set CDR offset to 10 */
+ { MDIO_MMD_PMAPMD, 0xcc01, 0xffff, 0x488a },
+
+ /* adjust 10G RX bias current */
+ { MDIO_MMD_PMAPMD, 0xcb1b, 0xffff, 0x0200 },
+ { MDIO_MMD_PMAPMD, 0xcb1c, 0xffff, 0x00f0 },
+ { MDIO_MMD_PMAPMD, 0xcc06, 0xffff, 0x00e0 },
+
+ /* end */
+ { 0, 0, 0, 0 }
+ };
+ int err;
+
+ err = set_phy_regs(phy, regs);
+ msleep(50);
+ if (err)
+ return err;
+
+ phy->priv = edc_sr;
+ return 0;
+}
+
+/*
+ * Setup EDC and other parameters for operation with an TWINAX module.
+ */
+static int ael2020_setup_twinax_edc(struct cphy *phy, int modtype)
+{
+ /* set uC to 40MHz */
+ static struct reg_val uCclock40MHz[] = {
+ { MDIO_MMD_PMAPMD, 0xff28, 0xffff, 0x4001 },
+ { MDIO_MMD_PMAPMD, 0xff2a, 0xffff, 0x0002 },
+ { 0, 0, 0, 0 }
+ };
+
+ /* activate uC clock */
+ static struct reg_val uCclockActivate[] = {
+ { MDIO_MMD_PMAPMD, 0xd000, 0xffff, 0x5200 },
+ { 0, 0, 0, 0 }
+ };
+
+ /* set PC to start of SRAM and activate uC */
+ static struct reg_val uCactivate[] = {
+ { MDIO_MMD_PMAPMD, 0xd080, 0xffff, 0x0100 },
+ { MDIO_MMD_PMAPMD, 0xd092, 0xffff, 0x0000 },
+ { 0, 0, 0, 0 }
+ };
+
+ /* TWINAX EDC firmware */
+ static u16 twinax_edc[] = {
+ 0xd800, 0x4009,
+ 0xd801, 0x2fff,
+ 0xd802, 0x300f,
+ 0xd803, 0x40aa,
+ 0xd804, 0x401c,
+ 0xd805, 0x401e,
+ 0xd806, 0x2ff4,
+ 0xd807, 0x3dc4,
+ 0xd808, 0x2035,
+ 0xd809, 0x3035,
+ 0xd80a, 0x6524,
+ 0xd80b, 0x2cb2,
+ 0xd80c, 0x3012,
+ 0xd80d, 0x1002,
+ 0xd80e, 0x26e2,
+ 0xd80f, 0x3022,
+ 0xd810, 0x1002,
+ 0xd811, 0x27d2,
+ 0xd812, 0x3022,
+ 0xd813, 0x1002,
+ 0xd814, 0x2822,
+ 0xd815, 0x3012,
+ 0xd816, 0x1002,
+ 0xd817, 0x2492,
+ 0xd818, 0x3022,
+ 0xd819, 0x1002,
+ 0xd81a, 0x2772,
+ 0xd81b, 0x3012,
+ 0xd81c, 0x1002,
+ 0xd81d, 0x23d2,
+ 0xd81e, 0x3022,
+ 0xd81f, 0x1002,
+ 0xd820, 0x22cd,
+ 0xd821, 0x301d,
+ 0xd822, 0x27f2,
+ 0xd823, 0x3022,
+ 0xd824, 0x1002,
+ 0xd825, 0x5553,
+ 0xd826, 0x0307,
+ 0xd827, 0x2522,
+ 0xd828, 0x3022,
+ 0xd829, 0x1002,
+ 0xd82a, 0x2142,
+ 0xd82b, 0x3012,
+ 0xd82c, 0x1002,
+ 0xd82d, 0x4016,
+ 0xd82e, 0x5e63,
+ 0xd82f, 0x0344,
+ 0xd830, 0x2142,
+ 0xd831, 0x3012,
+ 0xd832, 0x1002,
+ 0xd833, 0x400e,
+ 0xd834, 0x2522,
+ 0xd835, 0x3022,
+ 0xd836, 0x1002,
+ 0xd837, 0x2b52,
+ 0xd838, 0x3012,
+ 0xd839, 0x1002,
+ 0xd83a, 0x2742,
+ 0xd83b, 0x3022,
+ 0xd83c, 0x1002,
+ 0xd83d, 0x25e2,
+ 0xd83e, 0x3022,
+ 0xd83f, 0x1002,
+ 0xd840, 0x2fa4,
+ 0xd841, 0x3dc4,
+ 0xd842, 0x6624,
+ 0xd843, 0x414b,
+ 0xd844, 0x56b3,
+ 0xd845, 0x03c6,
+ 0xd846, 0x866b,
+ 0xd847, 0x400c,
+ 0xd848, 0x2712,
+ 0xd849, 0x3012,
+ 0xd84a, 0x1002,
+ 0xd84b, 0x2c4b,
+ 0xd84c, 0x309b,
+ 0xd84d, 0x56b3,
+ 0xd84e, 0x03c3,
+ 0xd84f, 0x866b,
+ 0xd850, 0x400c,
+ 0xd851, 0x2272,
+ 0xd852, 0x3022,
+ 0xd853, 0x1002,
+ 0xd854, 0x2742,
+ 0xd855, 0x3022,
+ 0xd856, 0x1002,
+ 0xd857, 0x25e2,
+ 0xd858, 0x3022,
+ 0xd859, 0x1002,
+ 0xd85a, 0x2fb4,
+ 0xd85b, 0x3dc4,
+ 0xd85c, 0x6624,
+ 0xd85d, 0x56b3,
+ 0xd85e, 0x03c3,
+ 0xd85f, 0x866b,
+ 0xd860, 0x401c,
+ 0xd861, 0x2c45,
+ 0xd862, 0x3095,
+ 0xd863, 0x5b53,
+ 0xd864, 0x2372,
+ 0xd865, 0x3012,
+ 0xd866, 0x13c2,
+ 0xd867, 0x5cc3,
+ 0xd868, 0x2712,
+ 0xd869, 0x3012,
+ 0xd86a, 0x1312,
+ 0xd86b, 0x2b52,
+ 0xd86c, 0x3012,
+ 0xd86d, 0x1002,
+ 0xd86e, 0x2742,
+ 0xd86f, 0x3022,
+ 0xd870, 0x1002,
+ 0xd871, 0x2582,
+ 0xd872, 0x3022,
+ 0xd873, 0x1002,
+ 0xd874, 0x2142,
+ 0xd875, 0x3012,
+ 0xd876, 0x1002,
+ 0xd877, 0x628f,
+ 0xd878, 0x2985,
+ 0xd879, 0x33a5,
+ 0xd87a, 0x25e2,
+ 0xd87b, 0x3022,
+ 0xd87c, 0x1002,
+ 0xd87d, 0x5653,
+ 0xd87e, 0x03d2,
+ 0xd87f, 0x401e,
+ 0xd880, 0x6f72,
+ 0xd881, 0x1002,
+ 0xd882, 0x628f,
+ 0xd883, 0x2304,
+ 0xd884, 0x3c84,
+ 0xd885, 0x6436,
+ 0xd886, 0xdff4,
+ 0xd887, 0x6436,
+ 0xd888, 0x2ff5,
+ 0xd889, 0x3005,
+ 0xd88a, 0x8656,
+ 0xd88b, 0xdfba,
+ 0xd88c, 0x56a3,
+ 0xd88d, 0xd05a,
+ 0xd88e, 0x2972,
+ 0xd88f, 0x3012,
+ 0xd890, 0x1392,
+ 0xd891, 0xd05a,
+ 0xd892, 0x56a3,
+ 0xd893, 0xdfba,
+ 0xd894, 0x0383,
+ 0xd895, 0x6f72,
+ 0xd896, 0x1002,
+ 0xd897, 0x2b45,
+ 0xd898, 0x3005,
+ 0xd899, 0x4178,
+ 0xd89a, 0x5653,
+ 0xd89b, 0x0384,
+ 0xd89c, 0x2a62,
+ 0xd89d, 0x3012,
+ 0xd89e, 0x1002,
+ 0xd89f, 0x2f05,
+ 0xd8a0, 0x3005,
+ 0xd8a1, 0x41c8,
+ 0xd8a2, 0x5653,
+ 0xd8a3, 0x0382,
+ 0xd8a4, 0x0002,
+ 0xd8a5, 0x4218,
+ 0xd8a6, 0x2474,
+ 0xd8a7, 0x3c84,
+ 0xd8a8, 0x6437,
+ 0xd8a9, 0xdff4,
+ 0xd8aa, 0x6437,
+ 0xd8ab, 0x2ff5,
+ 0xd8ac, 0x3c05,
+ 0xd8ad, 0x8757,
+ 0xd8ae, 0xb888,
+ 0xd8af, 0x9787,
+ 0xd8b0, 0xdff4,
+ 0xd8b1, 0x6724,
+ 0xd8b2, 0x866a,
+ 0xd8b3, 0x6f72,
+ 0xd8b4, 0x1002,
+ 0xd8b5, 0x2641,
+ 0xd8b6, 0x3021,
+ 0xd8b7, 0x1001,
+ 0xd8b8, 0xc620,
+ 0xd8b9, 0x0000,
+ 0xd8ba, 0xc621,
+ 0xd8bb, 0x0000,
+ 0xd8bc, 0xc622,
+ 0xd8bd, 0x00ce,
+ 0xd8be, 0xc623,
+ 0xd8bf, 0x007f,
+ 0xd8c0, 0xc624,
+ 0xd8c1, 0x0032,
+ 0xd8c2, 0xc625,
+ 0xd8c3, 0x0000,
+ 0xd8c4, 0xc627,
+ 0xd8c5, 0x0000,
+ 0xd8c6, 0xc628,
+ 0xd8c7, 0x0000,
+ 0xd8c8, 0xc62c,
+ 0xd8c9, 0x0000,
+ 0xd8ca, 0x0000,
+ 0xd8cb, 0x2641,
+ 0xd8cc, 0x3021,
+ 0xd8cd, 0x1001,
+ 0xd8ce, 0xc502,
+ 0xd8cf, 0x53ac,
+ 0xd8d0, 0xc503,
+ 0xd8d1, 0x2cd3,
+ 0xd8d2, 0xc600,
+ 0xd8d3, 0x2a6e,
+ 0xd8d4, 0xc601,
+ 0xd8d5, 0x2a2c,
+ 0xd8d6, 0xc605,
+ 0xd8d7, 0x5557,
+ 0xd8d8, 0xc60c,
+ 0xd8d9, 0x5400,
+ 0xd8da, 0xc710,
+ 0xd8db, 0x0700,
+ 0xd8dc, 0xc711,
+ 0xd8dd, 0x0f06,
+ 0xd8de, 0xc718,
+ 0xd8df, 0x0700,
+ 0xd8e0, 0xc719,
+ 0xd8e1, 0x0f06,
+ 0xd8e2, 0xc720,
+ 0xd8e3, 0x4700,
+ 0xd8e4, 0xc721,
+ 0xd8e5, 0x0f06,
+ 0xd8e6, 0xc728,
+ 0xd8e7, 0x0700,
+ 0xd8e8, 0xc729,
+ 0xd8e9, 0x1207,
+ 0xd8ea, 0xc801,
+ 0xd8eb, 0x7f50,
+ 0xd8ec, 0xc802,
+ 0xd8ed, 0x7760,
+ 0xd8ee, 0xc803,
+ 0xd8ef, 0x7fce,
+ 0xd8f0, 0xc804,
+ 0xd8f1, 0x520e,
+ 0xd8f2, 0xc805,
+ 0xd8f3, 0x5c11,
+ 0xd8f4, 0xc806,
+ 0xd8f5, 0x3c51,
+ 0xd8f6, 0xc807,
+ 0xd8f7, 0x4061,
+ 0xd8f8, 0xc808,
+ 0xd8f9, 0x49c1,
+ 0xd8fa, 0xc809,
+ 0xd8fb, 0x3840,
+ 0xd8fc, 0xc80a,
+ 0xd8fd, 0x0000,
+ 0xd8fe, 0xc821,
+ 0xd8ff, 0x0002,
+ 0xd900, 0xc822,
+ 0xd901, 0x0046,
+ 0xd902, 0xc844,
+ 0xd903, 0x182f,
+ 0xd904, 0xc013,
+ 0xd905, 0xf341,
+ 0xd906, 0xc084,
+ 0xd907, 0x0030,
+ 0xd908, 0xc904,
+ 0xd909, 0x1401,
+ 0xd90a, 0xcb0c,
+ 0xd90b, 0x0004,
+ 0xd90c, 0xcb0e,
+ 0xd90d, 0xa00a,
+ 0xd90e, 0xcb0f,
+ 0xd90f, 0xc0c0,
+ 0xd910, 0xcb10,
+ 0xd911, 0xc0c0,
+ 0xd912, 0xcb11,
+ 0xd913, 0x00a0,
+ 0xd914, 0xcb12,
+ 0xd915, 0x0007,
+ 0xd916, 0xc241,
+ 0xd917, 0xa000,
+ 0xd918, 0xc243,
+ 0xd919, 0x7fe0,
+ 0xd91a, 0xc604,
+ 0xd91b, 0x000e,
+ 0xd91c, 0xc609,
+ 0xd91d, 0x00f5,
+ 0xd91e, 0xc611,
+ 0xd91f, 0x000e,
+ 0xd920, 0xc660,
+ 0xd921, 0x9600,
+ 0xd922, 0xc687,
+ 0xd923, 0x0004,
+ 0xd924, 0xc60a,
+ 0xd925, 0x04f5,
+ 0xd926, 0x0000,
+ 0xd927, 0x2641,
+ 0xd928, 0x3021,
+ 0xd929, 0x1001,
+ 0xd92a, 0xc620,
+ 0xd92b, 0x14e5,
+ 0xd92c, 0xc621,
+ 0xd92d, 0xc53d,
+ 0xd92e, 0xc622,
+ 0xd92f, 0x3cbe,
+ 0xd930, 0xc623,
+ 0xd931, 0x4452,
+ 0xd932, 0xc624,
+ 0xd933, 0xc5c5,
+ 0xd934, 0xc625,
+ 0xd935, 0xe01e,
+ 0xd936, 0xc627,
+ 0xd937, 0x0000,
+ 0xd938, 0xc628,
+ 0xd939, 0x0000,
+ 0xd93a, 0xc62c,
+ 0xd93b, 0x0000,
+ 0xd93c, 0x0000,
+ 0xd93d, 0x2b84,
+ 0xd93e, 0x3c74,
+ 0xd93f, 0x6435,
+ 0xd940, 0xdff4,
+ 0xd941, 0x6435,
+ 0xd942, 0x2806,
+ 0xd943, 0x3006,
+ 0xd944, 0x8565,
+ 0xd945, 0x2b24,
+ 0xd946, 0x3c24,
+ 0xd947, 0x6436,
+ 0xd948, 0x1002,
+ 0xd949, 0x2b24,
+ 0xd94a, 0x3c24,
+ 0xd94b, 0x6436,
+ 0xd94c, 0x4045,
+ 0xd94d, 0x8656,
+ 0xd94e, 0x5663,
+ 0xd94f, 0x0302,
+ 0xd950, 0x401e,
+ 0xd951, 0x1002,
+ 0xd952, 0x2807,
+ 0xd953, 0x31a7,
+ 0xd954, 0x20c4,
+ 0xd955, 0x3c24,
+ 0xd956, 0x6724,
+ 0xd957, 0x1002,
+ 0xd958, 0x2807,
+ 0xd959, 0x3187,
+ 0xd95a, 0x20c4,
+ 0xd95b, 0x3c24,
+ 0xd95c, 0x6724,
+ 0xd95d, 0x1002,
+ 0xd95e, 0x24f4,
+ 0xd95f, 0x3c64,
+ 0xd960, 0x6436,
+ 0xd961, 0xdff4,
+ 0xd962, 0x6436,
+ 0xd963, 0x1002,
+ 0xd964, 0x2006,
+ 0xd965, 0x3d76,
+ 0xd966, 0xc161,
+ 0xd967, 0x6134,
+ 0xd968, 0x6135,
+ 0xd969, 0x5443,
+ 0xd96a, 0x0303,
+ 0xd96b, 0x6524,
+ 0xd96c, 0x00fb,
+ 0xd96d, 0x1002,
+ 0xd96e, 0x20d4,
+ 0xd96f, 0x3c24,
+ 0xd970, 0x2025,
+ 0xd971, 0x3005,
+ 0xd972, 0x6524,
+ 0xd973, 0x1002,
+ 0xd974, 0xd019,
+ 0xd975, 0x2104,
+ 0xd976, 0x3c24,
+ 0xd977, 0x2105,
+ 0xd978, 0x3805,
+ 0xd979, 0x6524,
+ 0xd97a, 0xdff4,
+ 0xd97b, 0x4005,
+ 0xd97c, 0x6524,
+ 0xd97d, 0x2e8d,
+ 0xd97e, 0x303d,
+ 0xd97f, 0x2408,
+ 0xd980, 0x35d8,
+ 0xd981, 0x5dd3,
+ 0xd982, 0x0307,
+ 0xd983, 0x8887,
+ 0xd984, 0x63a7,
+ 0xd985, 0x8887,
+ 0xd986, 0x63a7,
+ 0xd987, 0xdffd,
+ 0xd988, 0x00f9,
+ 0xd989, 0x1002,
+ 0xd98a, 0x0000,
+ };
+ int i, err;
+
+ /* set uC clock and activate it */
+ err = set_phy_regs(phy, uCclock40MHz);
+ msleep(500);
+ if (err)
+ return err;
+ err = set_phy_regs(phy, uCclockActivate);
+ msleep(500);
+ if (err)
+ return err;
+
+ /* write TWINAX EDC firmware into PHY */
+ for (i = 0; i < ARRAY_SIZE(twinax_edc) && !err; i += 2)
+ err = t3_mdio_write(phy, MDIO_MMD_PMAPMD, twinax_edc[i],
+ twinax_edc[i + 1]);
+ /* activate uC */
+ err = set_phy_regs(phy, uCactivate);
+ if (!err)
+ phy->priv = edc_twinax;
+ return err;
+}
+
+/*
+ * Return Module Type.
+ */
+static int ael2020_get_module_type(struct cphy *phy, int delay_ms)
+{
+ int v;
+ unsigned int stat;
+
+ v = t3_mdio_read(phy, MDIO_MMD_PMAPMD, AEL2020_GPIO_STAT, &stat);
+ if (v)
+ return v;
+
+ if (stat & (0x1 << (AEL2020_GPIO_MODDET*4))) {
+ /* module absent */
+ return phy_modtype_none;
+ }
+
+ return ael2xxx_get_module_type(phy, delay_ms);
+}
+
+/*
+ * Enable PHY interrupts. We enable "Module Detection" interrupts (on any
+ * state transition) and then generic Link Alarm Status Interrupt (LASI).
+ */
+static int ael2020_intr_enable(struct cphy *phy)
+{
+ int err = t3_mdio_write(phy, MDIO_MMD_PMAPMD, AEL2020_GPIO_CTRL,
+ 0x2 << (AEL2020_GPIO_MODDET*4));
+ return err ? err : t3_phy_lasi_intr_enable(phy);
+}
+
+/*
+ * Disable PHY interrupts. The mirror of the above ...
+ */
+static int ael2020_intr_disable(struct cphy *phy)
+{
+ int err = t3_mdio_write(phy, MDIO_MMD_PMAPMD, AEL2020_GPIO_CTRL,
+ 0x1 << (AEL2020_GPIO_MODDET*4));
+ return err ? err : t3_phy_lasi_intr_disable(phy);
+}
+
+/*
+ * Clear PHY interrupt state.
+ */
+static int ael2020_intr_clear(struct cphy *phy)
+{
+ /*
+ * The GPIO Interrupt register on the AEL2020 is a "Latching High"
+ * (LH) register which is cleared to the current state when it's read.
+ * Thus, we simply read the register and discard the result.
+ */
+ unsigned int stat;
+ int err = t3_mdio_read(phy, MDIO_MMD_PMAPMD, AEL2020_GPIO_INTR, &stat);
+ return err ? err : t3_phy_lasi_intr_clear(phy);
+}
+
+/*
+ * Reset the PHY and put it into a canonical operating state.
+ */
+static int ael2020_reset(struct cphy *phy, int wait)
+{
+ static struct reg_val regs0[] = {
+ /* Erratum #2: CDRLOL asserted, causing PMA link down status */
+ { MDIO_MMD_PMAPMD, 0xc003, 0xffff, 0x3101 },
+
+ /* force XAUI to send LF when RX_LOS is asserted */
+ { MDIO_MMD_PMAPMD, 0xcd40, 0xffff, 0x0001 },
+
+ /* RX_LOS pin is active high */
+ { MDIO_MMD_PMAPMD, AEL_OPT_SETTINGS,
+ 0x0020, 0x0020 },
+
+ /* output Module's Loss Of Signal (LOS) to LED */
+ { MDIO_MMD_PMAPMD, AEL2020_GPIO_CFG+AEL2020_GPIO_LSTAT,
+ 0xffff, 0x0004 },
+ { MDIO_MMD_PMAPMD, AEL2020_GPIO_CTRL,
+ 0xffff, 0x8 << (AEL2020_GPIO_LSTAT*4) },
+
+ /* end */
+ { 0, 0, 0, 0 }
+ };
+ int err;
+ unsigned int lasi_ctrl;
+
+ /* grab current interrupt state */
+ err = t3_mdio_read(phy, MDIO_MMD_PMAPMD, MDIO_PMA_LASI_CTRL,
+ &lasi_ctrl);
+ if (err)
+ return err;
+
+ err = t3_phy_reset(phy, MDIO_MMD_PMAPMD, 125);
+ if (err)
+ return err;
+ msleep(100);
+
+ /* basic initialization for all module types */
+ phy->priv = edc_none;
+ err = set_phy_regs(phy, regs0);
+ if (err)
+ return err;
+
+ /* determine module type and perform appropriate initialization */
+ err = ael2020_get_module_type(phy, 0);
+ if (err < 0)
+ return err;
+ phy->modtype = (u8)err;
+ if (err == phy_modtype_twinax || err == phy_modtype_twinax_long)
+ err = ael2020_setup_twinax_edc(phy, err);
+ else
+ err = ael2020_setup_sr_edc(phy);
+ if (err)
+ return err;
+
+ /* reset wipes out interrupts, reenable them if they were on */
+ if (lasi_ctrl & 1)
+ err = ael2005_intr_enable(phy);
+ return err;
+}
+
+/*
+ * Handle a PHY interrupt.
+ */
+static int ael2020_intr_handler(struct cphy *phy)
+{
+ unsigned int stat;
+ int ret, edc_needed, cause = 0;
+
+ ret = t3_mdio_read(phy, MDIO_MMD_PMAPMD, AEL2020_GPIO_INTR, &stat);
+ if (ret)
+ return ret;
+
+ if (stat & (0x1 << AEL2020_GPIO_MODDET)) {
+ /* modules have max 300 ms init time after hot plug */
+ ret = ael2020_get_module_type(phy, 300);
+ if (ret < 0)
+ return ret;
+
+ phy->modtype = (u8)ret;
+ if (ret == phy_modtype_none)
+ edc_needed = phy->priv; /* on unplug retain EDC */
+ else if (ret == phy_modtype_twinax ||
+ ret == phy_modtype_twinax_long)
+ edc_needed = edc_twinax;
+ else
+ edc_needed = edc_sr;
+
+ if (edc_needed != phy->priv) {
+ ret = ael2020_reset(phy, 0);
+ return ret ? ret : cphy_cause_module_change;
+ }
+ cause = cphy_cause_module_change;
+ }
+
+ ret = t3_phy_lasi_intr_handler(phy);
+ if (ret < 0)
+ return ret;
+
+ ret |= cause;
+ return ret ? ret : cphy_cause_link_change;
+}
+
+static struct cphy_ops ael2020_ops = {
+ .reset = ael2020_reset,
+ .intr_enable = ael2020_intr_enable,
+ .intr_disable = ael2020_intr_disable,
+ .intr_clear = ael2020_intr_clear,
+ .intr_handler = ael2020_intr_handler,
+ .get_link_status = get_link_status_r,
+ .power_down = ael1002_power_down,
+ .mmds = MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS | MDIO_DEVS_PHYXS,
+};
+
+int t3_ael2020_phy_prep(struct cphy *phy, struct adapter *adapter, int phy_addr,
+ const struct mdio_ops *mdio_ops)
+{
+ cphy_init(phy, adapter, phy_addr, &ael2020_ops, mdio_ops,
+ SUPPORTED_10000baseT_Full | SUPPORTED_AUI | SUPPORTED_FIBRE |
+ SUPPORTED_IRQ, "10GBASE-R");
+ msleep(125);
+ return 0;
+}
+
+/*
* Get link status for a 10GBASE-X device.
*/
static int get_link_status_x(struct cphy *phy, int *link_ok, int *speed,
diff --git a/drivers/net/cxgb3/common.h b/drivers/net/cxgb3/common.h
index 79a113b..301221a 100644
--- a/drivers/net/cxgb3/common.h
+++ b/drivers/net/cxgb3/common.h
@@ -802,6 +802,8 @@ int t3_ael1006_phy_prep(struct cphy *phy, struct adapter *adapter,
int phy_addr, const struct mdio_ops *mdio_ops);
int t3_ael2005_phy_prep(struct cphy *phy, struct adapter *adapter,
int phy_addr, const struct mdio_ops *mdio_ops);
+int t3_ael2020_phy_prep(struct cphy *phy, struct adapter *adapter,
+ int phy_addr, const struct mdio_ops *mdio_ops);
int t3_qt2045_phy_prep(struct cphy *phy, struct adapter *adapter, int phy_addr,
const struct mdio_ops *mdio_ops);
int t3_xaui_direct_phy_prep(struct cphy *phy, struct adapter *adapter,
diff --git a/drivers/net/cxgb3/cxgb3_main.c b/drivers/net/cxgb3/cxgb3_main.c
index 1fe4b07..4bc2656 100644
--- a/drivers/net/cxgb3/cxgb3_main.c
+++ b/drivers/net/cxgb3/cxgb3_main.c
@@ -91,6 +91,8 @@ static const struct pci_device_id cxgb3_pci_tbl[] = {
CH_DEVICE(0x31, 3), /* T3B20 */
CH_DEVICE(0x32, 1), /* T3B02 */
CH_DEVICE(0x35, 6), /* T3C20-derived T3C10 */
+ CH_DEVICE(0x36, 3), /* S320E-CR */
+ CH_DEVICE(0x37, 7), /* N320E-G2 */
{0,}
};
diff --git a/drivers/net/cxgb3/t3_hw.c b/drivers/net/cxgb3/t3_hw.c
index fc7db8a..766314c 100644
--- a/drivers/net/cxgb3/t3_hw.c
+++ b/drivers/net/cxgb3/t3_hw.c
@@ -526,6 +526,11 @@ static const struct adapter_info t3_adap_info[] = {
F_GPIO10_OEN | F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL | F_GPIO10_OUT_VAL,
{ S_GPIO9 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
&mi1_mdio_ext_ops, "Chelsio T310" },
+ {1, 0, 0,
+ F_GPIO1_OEN | F_GPIO6_OEN | F_GPIO7_OEN |
+ F_GPIO1_OUT_VAL | F_GPIO6_OUT_VAL,
+ { S_GPIO9 }, SUPPORTED_10000baseT_Full | SUPPORTED_AUI,
+ &mi1_mdio_ext_ops, "Chelsio N320E-G2" },
};
/*
@@ -552,6 +557,8 @@ static const struct port_type_info port_types[] = {
{ t3_qt2045_phy_prep },
{ t3_ael1006_phy_prep },
{ NULL },
+ { NULL },
+ { t3_ael2020_phy_prep },
};
#define VPD_ENTRY(name, len) \
next prev parent reply other threads:[~2009-05-29 7:58 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-05-29 7:58 [PATCH net-next 1/2] cxgb3: move away from LLTX Divy Le Ray
2009-05-29 7:58 ` Divy Le Ray [this message]
2009-05-30 3:21 ` [PATCH net-next 2/2] cxgb3: Add Aeluros 2020 phy support Ben Hutchings
2009-06-01 10:53 ` Ben Hutchings
2009-06-04 2:27 ` Divy Le Ray
2009-06-04 3:00 ` David Miller
2009-06-04 3:05 ` Divy Le Ray
2009-05-29 8:57 ` [PATCH net-next 1/2] cxgb3: move away from LLTX David Miller
2009-05-29 20:28 ` Divy Le Ray
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090529075829.30669.41488.stgit@speedy5 \
--to=divy@chelsio.com \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=swise@opengridcomputing.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.