From: Tobias Kaminsky <tobiaskaminsky@web.de>
To: linux-media@vger.kernel.org
Subject: Re: Two WinTV1110 in one PC not working, single works
Date: Thu, 4 Jun 2009 14:31:15 +0200 [thread overview]
Message-ID: <200906041431.15681.tobiaskaminsky@web.de> (raw)
In-Reply-To: <200906021632.43653.tobiaskaminsky@web.de>
Hello,
this is what I figured out.
If I am using the newest v4l-hg:
1) make install --> coldboot --> both card works --> coldboot --> just one
card works
2) make install --> init 0 (not powering completly off) --> just one card works
3) make install --> init 6 --> both card works
Please let me know what informations do you need!
Thank you!
Tobias Kaminsky
On Tuesday 02 June 2009 16:32:43 Tobias Kaminsky wrote:
> With a new firmware:
> -rw-r--r-- 1 root 24479 2009-06-02 16:09 /lib/firmware/dvb-fe-tda10046.fw
> -rw-r--r-- 1 root 24478 2009-06-02 16:09 /lib/firmware/dvb-fe-tda10046.fw-
> backup-02-06-09
>
> I get FE_HAS_LOCK on both cards, but
>
> root@finswimmer-desktop:/lib/firmware# tzap -a 1
> "ProSieben(ProSiebenSat.1)" using '/dev/dvb/adapter1/frontend0' and
> '/dev/dvb/adapter1/demux0' tuning to 738000000 Hz
> video pid 0x0131, audio pid 0x0132
> status 00 | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 |
> status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc 00000000 |
> FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber 0001fffe | unc
> 00000000 | FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber 0001fffe |
> unc 00000000 | FE_HAS_LOCK status 1f | signal 0000 | snr f6f6 | ber
> 0001fffe | unc 00000000 | FE_HAS_LOCK
>
> "ber" is always the same. Therefore there are no datas in dvr0.
>
>
> Jun 2 16:11:30 finswimmer-desktop root: card0
>
> Jun 2 16:11:33 finswimmer-desktop kernel: [ 6540.080006] tda1004x: setting
> up plls for 48MHz sampling clock
> Jun 2 16:11:33 finswimmer-desktop kernel: [ 6540.364007] tda1004x: found
> firmware revision 20 -- ok
>
>
>
> Jun 2 16:11:46 finswimmer-desktop root: card1
>
> Jun 2 16:11:49 finswimmer-desktop kernel: [ 6556.044007] tda1004x: setting
> up plls for 48MHz sampling clock
> Jun 2 16:11:49 finswimmer-desktop kernel: [ 6556.712007] tda1004x: found
> firmware revision 0 -- invalid
> Jun 2 16:11:49 finswimmer-desktop kernel: [ 6556.712015] tda1004x: trying
> to boot from eeprom
> Jun 2 16:11:52 finswimmer-desktop kernel: [ 6559.080007] tda1004x: found
> firmware revision 0 -- invalid
> Jun 2 16:11:52 finswimmer-desktop kernel: [ 6559.080013] tda1004x: waiting
> for firmware upload...
> Jun 2 16:11:52 finswimmer-desktop kernel: [ 6559.080017] firmware:
> requesting dvb-fe-tda10046.fw
> Jun 2 16:12:06 finswimmer-desktop kernel: [ 6573.524007] tda1004x: found
> firmware revision ed -- invalid
> Jun 2 16:12:06 finswimmer-desktop kernel: [ 6573.524013] tda1004x:
> firmware upload failed
> Jun 2 16:12:27 finswimmer-desktop kernel: [ 6594.332007] tda1004x: setting
> up plls for 48MHz sampling clock
> Jun 2 16:12:29 finswimmer-desktop kernel: [ 6596.616006] tda1004x: found
> firmware revision 0 -- invalid
> Jun 2 16:12:29 finswimmer-desktop kernel: [ 6596.616012] tda1004x: trying
> to boot from eeprom
> Jun 2 16:12:31 finswimmer-desktop kernel: [ 6598.984007] tda1004x: found
> firmware revision 0 -- invalid
> Jun 2 16:12:31 finswimmer-desktop kernel: [ 6598.984014] tda1004x: waiting
> for firmware upload...
> Jun 2 16:12:31 finswimmer-desktop kernel: [ 6598.984018] firmware:
> requesting dvb-fe-tda10046.fw
> Jun 2 16:12:46 finswimmer-desktop kernel: [ 6613.424007] tda1004x: found
> firmware revision ed -- invalid
> Jun 2 16:12:46 finswimmer-desktop kernel: [ 6613.424013] tda1004x:
> firmware upload failed
>
> On Tuesday 02 June 2009 15:57:27 Tobias Kaminsky wrote:
> > Hello,
> >
> > I have two WinTX1110 installed in one PC:
> >
> > 04:03.0 Multimedia controller: Philips Semiconductors
> > SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
> > 04:04.0 Multimedia controller: Philips Semiconductors
> > SAA7131/SAA7133/SAA7135 Video Broadcast Decoder (rev d1)
> >
> > The first card is working fine.
> > But the second fails to load the firmware:
> > [ 215.424008] tda1004x: found firmware revision 0 -- invalid
> > [ 215.424014] tda1004x: firmware upload failed
> >
> > I have tried both cards alone in the pc and they are working, but
> > together not.
> >
> > The "first" card says this:
> > [ 204.217357] tda1004x: found firmware revision 20 -- ok
> >
> > So the current status is that only one is working and I do not know what
> > I can change.
> >
> > The Firmware:
> > -rw-r--r-- 1 root 24478 2008-10-27 06:33 /lib/firmware/dvb-fe-tda10046.fw
> >
> > What else informations do you need?
> >
> > Thank you very much!
> >
> > Tobias Kaminsky
> >
> > dmesg:
> > [ 12.593302] Linux video capture interface: v2.00
> > [ 12.903476] saa7130/34: v4l2 driver version 0.2.14 loaded
> > [ 12.904699] saa7134 0000:04:03.0: PCI INT A -> GSI 16 (level, low) ->
> > IRQ 16
> > [ 12.904706] saa7133[0]: found at 0000:04:03.0, rev: 209, irq: 16,
> > latency: 32, mmio: 0xfdaff000
> > [ 12.904714] saa7133[0]: subsystem: 0070:6701, board: Hauppauge WinTV-
> > HVR1110 DVB-T/Hybrid [card=104,autodetected]
> > [ 12.904726] saa7133[0]: board init: gpio is 6400000
> > [ 13.063355] saa7133[0]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43
> > a9 1c 55 d2 b2 92
> > [ 13.063366] saa7133[0]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff
> > ff ff ff ff ff ff [ 13.063375] saa7133[0]: i2c eeprom 20: 01 40 01 32
> > 32 01 01 33 88 ff 00 aa ff ff ff ff
> > [ 13.063383] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
> > ff ff ff ff ff ff [ 13.063392] saa7133[0]: i2c eeprom 40: ff 21 00 c2
> > 96 10 03 32 15 60 ff ff ff ff ff ff
> > [ 13.063401] saa7133[0]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 13.063409] saa7133[0]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 13.063418] saa7133[0]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 13.063426] saa7133[0]: i2c eeprom 80: 84 09 00 04 20 77 00 40 6f 78
> > 0e f0 73 05 29 00
> > [ 13.063435] saa7133[0]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48
> > 89 72 07 70 73 09
> > [ 13.063444] saa7133[0]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72
> > 0e 01 72 0f 03 72
> > [ 13.063452] saa7133[0]: i2c eeprom b0: 10 01 72 11 ff 79 49 00 00 00
> > 00 00 00 00 00 00
> > [ 13.063461] saa7133[0]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 13.063469] saa7133[0]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 13.063478] saa7133[0]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 13.063486] saa7133[0]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 13.364324] tuner' 1-004b: chip found @ 0x96 (saa7133[0])
> > [ 13.367371] tveeprom 1-0050: Hauppauge model 67019, rev B4B4, serial#
> > 948335
> > [ 13.367375] tveeprom 1-0050: MAC address is 00-0D-FE-0E-78-6F
> > [ 13.367378] tveeprom 1-0050: tuner model is Philips 8275A (idx 114,
> > type 4) [ 13.367381] tveeprom 1-0050: TV standards PAL(B/G) NTSC(M)
> > PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
> > [ 13.367385] tveeprom 1-0050: audio processor is SAA7131 (idx 41)
> > [ 13.367387] tveeprom 1-0050: decoder processor is SAA7131 (idx 35)
> > [ 13.367390] tveeprom 1-0050: has radio, has IR receiver, has IR
> > transmitter [ 13.367392] saa7133[0]: hauppauge eeprom: model=67019
> > [ 13.456094] tda829x 1-004b: setting tuner address to 61
> > [ 13.556076] tda829x 1-004b: type set to tda8290+75a
> > [ 17.422485] saa7133[0]: registered device video0 [v4l2]
> > [ 17.422789] saa7133[0]: registered device vbi0
> > [ 17.423087] saa7133[0]: registered device radio0
> > [ 17.484044] saa7134 0000:04:04.0: PCI INT A -> GSI 17 (level, low) ->
> > IRQ 17
> > [ 17.484052] saa7133[1]: found at 0000:04:04.0, rev: 209, irq: 17,
> > latency: 32, mmio: 0xfdafe000
> > [ 17.484060] saa7133[1]: subsystem: 0070:6701, board: Hauppauge WinTV-
> > HVR1110 DVB-T/Hybrid [card=104,autodetected]
> > [ 17.484072] saa7133[1]: board init: gpio is 6400000
> > [ 17.628082] tuner' 2-004b: chip found @ 0x96 (saa7133[1])
> > [ 17.676014] saa7133[1]: i2c eeprom 00: 70 00 01 67 54 20 1c 00 43 43
> > a9 1c 55 d2 b2 92
> > [ 17.676024] saa7133[1]: i2c eeprom 10: ff ff ff 0e ff 20 ff ff ff ff
> > ff ff ff ff ff ff [ 17.676033] saa7133[1]: i2c eeprom 20: 01 40 01 32
> > 32 01 01 33 88 ff 00 aa ff ff ff ff
> > [ 17.676042] saa7133[1]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
> > ff ff ff ff ff ff [ 17.676051] saa7133[1]: i2c eeprom 40: ff 21 00 c2
> > 96 10 03 32 15 60 ff ff ff ff ff ff
> > [ 17.676059] saa7133[1]: i2c eeprom 50: ff 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 17.676068] saa7133[1]: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 17.676077] saa7133[1]: i2c eeprom 70: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 17.676085] saa7133[1]: i2c eeprom 80: 84 09 00 04 20 77 00 40 59 4b
> > 4f f0 73 05 29 00
> > [ 17.676094] saa7133[1]: i2c eeprom 90: 84 08 00 06 cb 05 01 00 94 48
> > 89 72 07 70 73 09
> > [ 17.676103] saa7133[1]: i2c eeprom a0: 23 5f 73 0a fc 72 72 0b 2f 72
> > 0e 01 72 0f 03 72
> > [ 17.676111] saa7133[1]: i2c eeprom b0: 10 01 72 11 ff 79 4b 00 00 00
> > 00 00 00 00 00 00
> > [ 17.676120] saa7133[1]: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 17.676128] saa7133[1]: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 17.676137] saa7133[1]: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 17.676146] saa7133[1]: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00
> > 00 00 00 00 00 00
> > [ 17.685388] tveeprom 2-0050: Hauppauge model 67019, rev B4B4, serial#
> > 5196633
> > [ 17.685392] tveeprom 2-0050: MAC address is 00-0D-FE-4F-4B-59
> > [ 17.685395] tveeprom 2-0050: tuner model is Philips 8275A (idx 114,
> > type 4) [ 17.685398] tveeprom 2-0050: TV standards PAL(B/G) NTSC(M)
> > PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc)
> > [ 17.685402] tveeprom 2-0050: audio processor is SAA7131 (idx 41)
> > [ 17.685404] tveeprom 2-0050: decoder processor is SAA7131 (idx 35)
> > [ 17.685407] tveeprom 2-0050: has radio, has IR receiver, has IR
> > transmitter [ 17.685410] saa7133[1]: hauppauge eeprom: model=67019
> > [ 17.772015] tda829x 2-004b: setting tuner address to 61
> > [ 17.836014] tda829x 2-004b: type set to tda8290+75a
> > [ 21.692599] saa7133[1]: registered device video1 [v4l2]
> > [ 21.692915] saa7133[1]: registered device vbi1
> > [ 21.693223] saa7133[1]: registered device radio1
> > [ 21.777372] saa7134 ALSA driver for DMA sound loaded
> > [ 21.789059] saa7133[0]/alsa: saa7133[0] at 0xfdaff000 irq 16
> > registered as card -2
> > [ 21.789550] saa7133[1]/alsa: saa7133[1] at 0xfdafe000 irq 17
> > registered as card -1
> > [ 21.938693] DVB: registering new adapter (saa7133[0])
> > [ 21.938698] DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
> >
> >
> > --
> > To unsubscribe from this list: send the line "unsubscribe linux-media" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at http://vger.kernel.org/majordomo-info.html
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2009-06-04 12:31 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-06-02 13:57 Two WinTV1110 in one PC not working, single works Tobias Kaminsky
2009-06-02 14:32 ` Tobias Kaminsky
2009-06-04 12:31 ` Tobias Kaminsky [this message]
2009-06-05 12:55 ` Tobias Kaminsky
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200906041431.15681.tobiaskaminsky@web.de \
--to=tobiaskaminsky@web.de \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.