From mboxrd@z Thu Jan  1 00:00:00 1970
From: Ondrej Zary <linux@rainbow-software.org>
Subject: cmi8330: revert comments about AD1848 back
Date: Sat, 27 Jun 2009 16:26:35 +0200
Message-ID: <200906271626.36466.linux@rainbow-software.org>
Mime-Version: 1.0
Content-Type: text/plain; charset="us-ascii"
Content-Transfer-Encoding: 7bit
Return-path: <alsa-devel-bounces@alsa-project.org>
Received: from mail.atlantis.sk (mail.atlantis.sk [80.94.52.35])
	by alsa0.perex.cz (Postfix) with ESMTP id E5B28246F7
	for <alsa-devel@alsa-project.org>;
	Sat, 27 Jun 2009 16:26:40 +0200 (CEST)
Content-Disposition: inline
List-Unsubscribe: <http://mailman.alsa-project.org/mailman/listinfo/alsa-devel>,
	<mailto:alsa-devel-request@alsa-project.org?subject=unsubscribe>
List-Archive: <http://mailman.alsa-project.org/pipermail/alsa-devel>
List-Post: <mailto:alsa-devel@alsa-project.org>
List-Help: <mailto:alsa-devel-request@alsa-project.org?subject=help>
List-Subscribe: <http://mailman.alsa-project.org/mailman/listinfo/alsa-devel>,
	<mailto:alsa-devel-request@alsa-project.org?subject=subscribe>
Sender: alsa-devel-bounces@alsa-project.org
Errors-To: alsa-devel-bounces@alsa-project.org
To: alsa-devel@alsa-project.org
List-Id: alsa-devel@alsa-project.org

In ALSA 1.0.20, the comments were changed to say CMI8330 instead of AD1848.
The CMI8330 chip includes two codecs - AD1848 and SB16, so the comments were
correct and are misleading now. Revert them back.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>

--- linux-2.6.30-orig/sound/isa/cmi8330.c	2009-06-10 05:05:27.000000000 +0200
+++ linux-test/sound/isa/cmi8330.c	2009-06-27 16:20:51.000000000 +0200
@@ -35,7 +35,7 @@
  *
  *  This card has two mixers and two PCM devices.  I've cheesed it such
  *  that recording and playback can be done through the same device.
- *  The driver "magically" routes the capturing to the CMI8330 codec,
+ *  The driver "magically" routes the capturing to the AD1848 codec,
  *  and playback to the SB16 codec.  This allows for full-duplex mode
  *  to some extent.
  *  The utilities in alsa-utils are aware of both devices, so passing
@@ -345,7 +345,7 @@
 
 	err = pnp_activate_dev(pdev);
 	if (err < 0) {
-		snd_printk(KERN_ERR "CMI8330/C3D PnP configure failure\n");
+		snd_printk(KERN_ERR "CMI8330/C3D (AD1848) PnP configure failure\n");
 		return -EBUSY;
 	}
 	wssport[dev] = pnp_port_start(pdev, 0);
@@ -527,11 +527,11 @@
 			     wssdma[dev], -1,
 			     WSS_HW_DETECT, 0, &acard->wss);
 	if (err < 0) {
-		snd_printk(KERN_ERR PFX "(CMI8330) device busy??\n");
+		snd_printk(KERN_ERR PFX "(AD1848) device busy??\n");
 		return err;
 	}
 	if (acard->wss->hardware != WSS_HW_CMI8330) {
-		snd_printk(KERN_ERR PFX "(CMI8330) not found during probe\n");
+		snd_printk(KERN_ERR PFX "(AD1848) not found during probe\n");
 		return -ENODEV;
 	}
 

-- 
Ondrej Zary