From: Magnus Damm <magnus.damm@gmail.com>
To: linux-sh@vger.kernel.org
Subject: [PATCH] sh: kfr2r09 romImage support
Date: Wed, 29 Jul 2009 12:55:56 +0000 [thread overview]
Message-ID: <20090729125556.3596.77154.sendpatchset@rx1.opensource.se> (raw)
From: Magnus Damm <damm@igel.co.jp>
This patch adds romImage support for the kfr2r09 board.
The partner-jet-setup.txt file is converted into assembly code
which becomes the first code to execute from the reset vector.
The file partner-jet-setup.txt can also be used to setup
the hardware using a JTAG debugger so booting from RAM can
be done without burning the code to flash.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
---
arch/sh/include/mach-kfr2r09/partner-jet-setup.txt | 134 ++++++++++++++++++++
arch/sh/include/mach-kfr2r09/romimage.h | 75 +++++++++++
2 files changed, 209 insertions(+)
--- /dev/null
+++ work/arch/sh/include/mach-kfr2r09/partner-jet-setup.txt 2009-07-29 20:52:45.000000000 +0900
@@ -0,0 +1,134 @@
+LIST "partner-jet-setup.txt - 20090722 Magnus Damm"
+LIST "set up enough of the kfr2r09 hardware to boot the kernel"
+
+LIST "CONFIG_ZIMAGE_BOOT_LOADER=n (RAM boot)"
+LIST "This script can be used to boot the kernel from RAM via JTAG:"
+LIST "> < partner-jet-setup.txt"
+LIST "> RD zImage, 0xa8800000"
+LIST "> G=0xa8800000"
+
+LIST "CONFIG_ZIMAGE_BOOT_LOADER=y (Flash boot)"
+LIST "Use the following command to burn the zImage to flash via JTAG:"
+LIST "> RD zImage, 0"
+
+LIST "--------------------------------"
+
+LIST "disable watchdog"
+EW 0xa4520004, 0xa507
+
+LIST "select mode for cs5 + cs6"
+ED 0xff800020, 0xa5a50001
+ED 0xfec10000, 0x0000001b
+
+LIST "setup clocks"
+ED 0xa4150004, 0x00000050
+ED 0xa4150000, 0x91053508
+WAIT 1
+ED 0xa4150024, 0x00005000
+
+LIST "setup pins"
+EB 0xa4050120, 0x00
+EB 0xa4050122, 0x00
+EB 0xa4050124, 0x00
+EB 0xa4050126, 0x00
+EB 0xa4050128, 0xA0
+EB 0xa405012A, 0x10
+EB 0xa405012C, 0x00
+EB 0xa405012E, 0x00
+EB 0xa4050130, 0x00
+EB 0xa4050132, 0x00
+EB 0xa4050134, 0x01
+EB 0xa4050136, 0x40
+EB 0xa4050138, 0x00
+EB 0xa405013A, 0x00
+EB 0xa405013C, 0x00
+EB 0xa405013E, 0x20
+EB 0xa4050160, 0x00
+EB 0xa4050162, 0x40
+EB 0xa4050164, 0x03
+EB 0xa4050166, 0x00
+EB 0xa4050168, 0x00
+EB 0xa405016A, 0x00
+EB 0xa405016C, 0x00
+
+EW 0xa405014E, 0x5660
+EW 0xa4050150, 0x0145
+EW 0xa4050152, 0x1550
+EW 0xa4050154, 0x0200
+EW 0xa4050156, 0x0040
+
+EW 0xa4050158, 0x0000
+EW 0xa405015a, 0x0000
+EW 0xa405015c, 0x0000
+EW 0xa405015e, 0x0000
+
+EW 0xa4050180, 0x0000
+EW 0xa4050182, 0x8002
+EW 0xa4050184, 0x0000
+
+EW 0xa405018a, 0x9991
+EW 0xa405018c, 0x8011
+EW 0xa405018e, 0x9550
+
+EW 0xa4050100, 0x0000
+EW 0xa4050102, 0x5540
+EW 0xa4050104, 0x0000
+EW 0xa4050106, 0x0000
+EW 0xa4050108, 0x4550
+EW 0xa405010a, 0x0130
+EW 0xa405010c, 0x0555
+EW 0xa405010e, 0x0000
+EW 0xa4050110, 0x0000
+EW 0xa4050112, 0xAAA8
+EW 0xa4050114, 0x8305
+EW 0xa4050116, 0x10F0
+EW 0xa4050118, 0x0F50
+EW 0xa405011a, 0x0000
+EW 0xa405011c, 0x0000
+EW 0xa405011e, 0x0555
+EW 0xa4050140, 0x0000
+EW 0xa4050142, 0x5141
+EW 0xa4050144, 0x5005
+EW 0xa4050146, 0xAAA9
+EW 0xa4050148, 0xFAA9
+EW 0xa405014a, 0x3000
+EW 0xa405014c, 0x0000
+
+LIST "setup sdram"
+ED 0xFD000108, 0x40000301
+ED 0xFD000020, 0x011B0002
+ED 0xFD000030, 0x03060E02
+ED 0xFD000034, 0x01020102
+ED 0xFD000038, 0x01090406
+ED 0xFD000008, 0x00000004
+ED 0xFD000040, 0x00000001
+ED 0xFD000040, 0x00000000
+ED 0xFD000018, 0x00000001
+
+WAIT 1
+
+ED 0xFD000014, 0x00000002
+ED 0xFD000060, 0x00000032
+ED 0xFD000060, 0x00020000
+ED 0xFD000014, 0x00000004
+ED 0xFD000014, 0x00000004
+ED 0xFD000010, 0x00000001
+ED 0xFD000044, 0x000004AF
+ED 0xFD000048, 0x20CF0037
+
+LIST "read 16 bytes from sdram"
+DD 0xa8000000, 0xa8000000, 1
+DD 0xa8000004, 0xa8000004, 1
+DD 0xa8000008, 0xa8000008, 1
+DD 0xa800000c, 0xa800000c, 1
+
+ED 0xFD000014, 0x00000002
+ED 0xFD000014, 0x00000004
+ED 0xFD000108, 0x40000300
+ED 0xFD000040, 0x00010000
+
+LIST "write to internal ram"
+ED 0xfd8007fc, 0
+
+LIST "setup cache"
+ED 0xff00001c, 0x0000090b
--- /dev/null
+++ work/arch/sh/include/mach-kfr2r09/romimage.h 2009-07-29 20:55:03.000000000 +0900
@@ -0,0 +1,75 @@
+/* kfr2r09 board specific boot code:
+ * converts the "partner-jet-script.txt" script into assembly
+ * the assembly code is the first code to be executed in the zImage
+ */
+
+/* The LIST command is used to include comments in the script */
+.macro LIST comment
+.endm
+
+/* The ED command is used to write a 32-bit word */
+.macro ED, addr, data
+ mov.l 1f ,r1
+ mov.l 2f ,r0
+ mov.l r0, @r1
+ bra 3f
+ nop
+ .align 2
+1: .long \addr
+2: .long \data
+3:
+.endm
+
+/* The EW command is used to write a 16-bit word */
+.macro EW, addr, data
+ mov.l 1f ,r1
+ mov.l 2f ,r0
+ mov.w r0, @r1
+ bra 3f
+ nop
+ .align 2
+1: .long \addr
+2: .long \data
+3:
+.endm
+
+/* The EB command is used to write an 8-bit word */
+.macro EB, addr, data
+ mov.l 1f ,r1
+ mov.l 2f ,r0
+ mov.b r0, @r1
+ bra 3f
+ nop
+ .align 2
+1: .long \addr
+2: .long \data
+3:
+.endm
+
+/* The WAIT command is used to delay the execution */
+.macro WAIT, time
+ mov.l 2f ,r3
+1:
+ nop
+ tst r3, r3
+ bf/s 1b
+ dt r3
+ bra 3f
+ nop
+ .align 2
+2: .long \time * 100
+3:
+.endm
+
+/* The DD command is used to read a 32-bit word */
+.macro DD, addr, addr2, nr
+ mov.l 1f ,r1
+ mov.l @r1, r0
+ bra 2f
+ nop
+ .align 2
+1: .long \addr
+2:
+.endm
+
+#include "partner-jet-setup.txt"
reply other threads:[~2009-07-29 12:55 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20090729125556.3596.77154.sendpatchset@rx1.opensource.se \
--to=magnus.damm@gmail.com \
--cc=linux-sh@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.