[lm-sensors] [PATCH] hwmon: (w83791d) Clean up detect function

[Jean Delvare <khali@linux-fr.org>]

As kind is now hard-coded to -1, there is room for code clean-ups.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
---
 drivers/hwmon/w83791d.c |   60 ++++++++++++++---------------------------------
 1 file changed, 18 insertions(+), 42 deletions(-)

--- linux-2.6.32-rc3.orig/drivers/hwmon/w83791d.c	2009-10-06 10:33:15.000000000 +0200
+++ linux-2.6.32-rc3/drivers/hwmon/w83791d.c	2009-10-06 12:13:28.000000000 +0200
@@ -1270,56 +1270,32 @@ static int w83791d_detect(struct i2c_cli
 		return -ENODEV;
 	}
 
-	/* The w83791d may be stuck in some other bank than bank 0. This may
-	   make reading other information impossible. Specify a force=...
-	   parameter, and the Winbond will be reset to the right bank. */
-	if (kind < 0) {
-		if (w83791d_read(client, W83791D_REG_CONFIG) & 0x80) {
-			return -ENODEV;
-		}
-		val1 = w83791d_read(client, W83791D_REG_BANK);
-		val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
-		/* Check for Winbond ID if in bank 0 */
-		if (!(val1 & 0x07)) {
-			/* yes it is Bank0 */
-			if (((!(val1 & 0x80)) && (val2 != 0xa3)) ||
-			    ((val1 & 0x80) && (val2 != 0x5c))) {
-				return -ENODEV;
-			}
-		}
-		/* If Winbond chip, address of chip and W83791D_REG_I2C_ADDR
-		   should match */
-		if (w83791d_read(client, W83791D_REG_I2C_ADDR) != address) {
+	if (w83791d_read(client, W83791D_REG_CONFIG) & 0x80)
+		return -ENODEV;
+
+	val1 = w83791d_read(client, W83791D_REG_BANK);
+	val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
+	/* Check for Winbond ID if in bank 0 */
+	if (!(val1 & 0x07)) {
+		if ((!(val1 & 0x80) && val2 != 0xa3) ||
+		    ( (val1 & 0x80) && val2 != 0x5c)) {
 			return -ENODEV;
 		}
 	}
+	/* If Winbond chip, address of chip and W83791D_REG_I2C_ADDR
+	   should match */
+	if (w83791d_read(client, W83791D_REG_I2C_ADDR) != address)
+		return -ENODEV;
 
-	/* We either have a force parameter or we have reason to
-	   believe it is a Winbond chip. Either way, we want bank 0 and
-	   Vendor ID high byte */
+	/* We want bank 0 and Vendor ID high byte */
 	val1 = w83791d_read(client, W83791D_REG_BANK) & 0x78;
 	w83791d_write(client, W83791D_REG_BANK, val1 | 0x80);
 
 	/* Verify it is a Winbond w83791d */
-	if (kind <= 0) {
-		/* get vendor ID */
-		val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
-		if (val2 != 0x5c) {	/* the vendor is NOT Winbond */
-			return -ENODEV;
-		}
-		val1 = w83791d_read(client, W83791D_REG_WCHIPID);
-		if (val1 = 0x71) {
-			kind = w83791d;
-		} else {
-			if (kind = 0)
-				dev_warn(&adapter->dev,
-					"w83791d: Ignoring 'force' parameter "
-					"for unknown chip at adapter %d, "
-					"address 0x%02x\n",
-					i2c_adapter_id(adapter), address);
-			return -ENODEV;
-		}
-	}
+	val1 = w83791d_read(client, W83791D_REG_WCHIPID);
+	val2 = w83791d_read(client, W83791D_REG_CHIPMAN);
+	if (val1 != 0x71 || val2 != 0x5c)
+		return -ENODEV;
 
 	strlcpy(info->type, "w83791d", I2C_NAME_SIZE);
 


-- 
Jean Delvare

_______________________________________________
lm-sensors mailing list
lm-sensors@lm-sensors.org
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors