From: "Luis R. Rodriguez" <lrodriguez@atheros.com>
To: <linux-wireless@vger.kernel.org>
Subject: odd state reached when AP deauths you after assoc
Date: Wed, 28 Oct 2009 11:37:26 -0700 [thread overview]
Message-ID: <20091028183726.GA4952@tux> (raw)
I ran into this when ath5k with wpa_supplicant with config file with
a wrong password against a Cisco AP. It seems the Cisco AP auths you
and lets you assoc but later it deauths you -- I guess after it
determines you are auth credentials failed. When this happens I get:
mcgrof@tux ~ $ iw dev wlan0 link
Authenticated with 00:0b:85:5b:8d:6c (on wlan0)
Not connected.
The log *after* this is below. I'll try to reproduce again, I can reproduce
all the time.
[ 171.905675] wlan0: deauthenticating from 00:0b:85:5b:a6:ec by local choice (reason=3)
[ 171.929065] ------------[ cut here ]------------
[ 171.929106] WARNING: at net/mac80211/scan.c:267 ieee80211_scan_completed+0x240/0x270 [mac80211]()
[ 171.929112] Hardware name: 7660A14
[ 171.929117] Modules linked in: i915 drm_kms_helper drm i2c_algo_bit binfmt_misc ppdev bridge stp bnep lp parport snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_pcm_oss snd_mixer_oss snd_pcm arc4 snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi ath5k snd_seq_midi_event snd_seq joydev snd_timer snd_seq_device mac80211 ath snd pcmcia soundcore cfg80211 thinkpad_acpi video intel_agp psmouse snd_page_alloc nvram led_class yenta_socket rsrc_nonstatic pcmcia_core output agpgart pcspkr serio_raw btusb iTCO_wdt iTCO_vendor_support ohci1394 ieee1394 e1000e
[ 171.929226] Pid: 4022, comm: wpa_supplicant Not tainted 2.6.32-rc5-wl #27
[ 171.929231] Call Trace:
[ 171.929245] [<c05a3a23>] ? printk+0x1d/0x22
[ 171.929269] [<f8379040>] ? ieee80211_scan_completed+0x240/0x270 [mac80211]
[ 171.929281] [<c0146121>] warn_slowpath_common+0x71/0xd0
[ 171.929306] [<f8379040>] ? ieee80211_scan_completed+0x240/0x270 [mac80211]
[ 171.929316] [<c014619a>] warn_slowpath_null+0x1a/0x20
[ 171.929340] [<f8379040>] ieee80211_scan_completed+0x240/0x270 [mac80211]
[ 171.929363] [<f83790b9>] ieee80211_scan_cancel+0x49/0x80 [mac80211]
[ 171.929388] [<f83826ca>] ieee80211_stop+0x59a/0x5b0 [mac80211]
[ 171.929399] [<c04e513e>] ? dev_deactivate+0x17e/0x1a0
[ 171.929412] [<c04d34cb>] dev_close+0x6b/0xc0
[ 171.929421] [<c05a6733>] ? _spin_unlock_bh+0x13/0x20
[ 171.929430] [<c04d150f>] ? dev_set_rx_mode+0x2f/0x40
[ 171.929438] [<c04d2d44>] dev_change_flags+0x84/0x1d0
[ 171.929448] [<c05207ea>] devinet_ioctl+0x54a/0x600
[ 171.929456] [<c04d489d>] ? dev_ioctl+0x28d/0x530
[ 171.929465] [<c0521c6a>] inet_ioctl+0x9a/0xc0
[ 171.929475] [<c04c25c8>] sock_ioctl+0x68/0x270
[ 171.929483] [<c04c2560>] ? sock_ioctl+0x0/0x270
[ 171.929493] [<c021bb9d>] vfs_ioctl+0x2d/0x90
[ 171.929501] [<c021bd62>] do_vfs_ioctl+0x72/0x5f0
[ 171.929510] [<c02267bf>] ? mntput_no_expire+0x1f/0xd0
[ 171.929520] [<c020c2ca>] ? __fput+0x17a/0x1f0
[ 171.929529] [<c020c367>] ? fput+0x27/0x30
[ 171.929537] [<c0207aec>] ? filp_close+0x4c/0x80
[ 171.929545] [<c021c34b>] sys_ioctl+0x6b/0x70
[ 171.929554] [<c01030dc>] sysenter_do_call+0x12/0x28
[ 171.929560] ---[ end trace d6c0a8110c16e049 ]---
[ 171.937047] phy0: device now idle
[ 171.938704] ------------[ cut here ]------------
[ 171.938733] WARNING: at net/wireless/core.c:619 wdev_cleanup_work+0xbf/0xe0 [cfg80211]()
[ 171.938741] Hardware name: 7660A14
[ 171.938746] Modules linked in: i915 drm_kms_helper drm i2c_algo_bit binfmt_misc ppdev bridge stp bnep lp parport snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_pcm_oss snd_mixer_oss snd_pcm arc4 snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi ath5k snd_seq_midi_event snd_seq joydev snd_timer snd_seq_device mac80211 ath snd pcmcia soundcore cfg80211 thinkpad_acpi video intel_agp psmouse snd_page_alloc nvram led_class yenta_socket rsrc_nonstatic pcmcia_core output agpgart pcspkr serio_raw btusb iTCO_wdt iTCO_vendor_support ohci1394 ieee1394 e1000e
[ 171.938873] Pid: 9, comm: events/0 Tainted: G W 2.6.32-rc5-wl #27
[ 171.938880] Call Trace:
[ 171.938892] [<c05a3a23>] ? printk+0x1d/0x22
[ 171.938910] [<f82cd18f>] ? wdev_cleanup_work+0xbf/0xe0 [cfg80211]
[ 171.938922] [<c0146121>] warn_slowpath_common+0x71/0xd0
[ 171.938939] [<f82cd18f>] ? wdev_cleanup_work+0xbf/0xe0 [cfg80211]
[ 171.938950] [<c014619a>] warn_slowpath_null+0x1a/0x20
[ 171.938967] [<f82cd18f>] wdev_cleanup_work+0xbf/0xe0 [cfg80211]
[ 171.938981] [<c01639b4>] worker_thread+0x134/0x200
[ 171.938998] [<f82cd0d0>] ? wdev_cleanup_work+0x0/0xe0 [cfg80211]
[ 171.939010] [<c0168600>] ? autoremove_wake_function+0x0/0x50
[ 171.939021] [<c0163880>] ? worker_thread+0x0/0x200
[ 171.939031] [<c01682b4>] kthread+0x74/0x80
[ 171.939041] [<c0168240>] ? kthread+0x0/0x80
[ 171.939051] [<c0103c47>] kernel_thread_helper+0x7/0x10
[ 171.939059] ---[ end trace d6c0a8110c16e04a ]---
[ 171.957054] CE: hpet increasing min_delta_ns to 15000 nsec
[ 173.591594] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 173.816116] phy0: device no longer idle - scanning
[ 177.440103] ------------[ cut here ]------------
[ 177.440138] WARNING: at net/wireless/scan.c:88 cfg80211_scan_done+0x4b/0x50 [cfg80211]()
[ 177.440145] Hardware name: 7660A14
[ 177.440150] Modules linked in: i915 drm_kms_helper drm i2c_algo_bit binfmt_misc ppdev bridge stp bnep lp parport snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_pcm_oss snd_mixer_oss snd_pcm arc4 snd_seq_dummy snd_seq_oss snd_seq_midi snd_rawmidi ath5k snd_seq_midi_event snd_seq joydev snd_timer snd_seq_device mac80211 ath snd pcmcia soundcore cfg80211 thinkpad_acpi video intel_agp psmouse snd_page_alloc nvram led_class yenta_socket rsrc_nonstatic pcmcia_core output agpgart pcspkr serio_raw btusb iTCO_wdt iTCO_vendor_support ohci1394 ieee1394 e1000e
[ 177.440256] Pid: 1864, comm: phy0 Tainted: G W 2.6.32-rc5-wl #27
[ 177.440262] Call Trace:
[ 177.440275] [<c05a3a23>] ? printk+0x1d/0x22
[ 177.440293] [<f82d17fb>] ? cfg80211_scan_done+0x4b/0x50 [cfg80211]
[ 177.440306] [<c0146121>] warn_slowpath_common+0x71/0xd0
[ 177.440322] [<f82d17fb>] ? cfg80211_scan_done+0x4b/0x50 [cfg80211]
[ 177.440332] [<c014619a>] warn_slowpath_null+0x1a/0x20
[ 177.440349] [<f82d17fb>] cfg80211_scan_done+0x4b/0x50 [cfg80211]
[ 177.440374] [<f8378e54>] ieee80211_scan_completed+0x54/0x270 [mac80211]
[ 177.440397] [<f8379236>] ieee80211_scan_work+0x146/0x4b0 [mac80211]
[ 177.440408] [<c01bb51d>] ? probe_workqueue_execution+0x8d/0xb0
[ 177.440420] [<c01639b4>] worker_thread+0x134/0x200
[ 177.440444] [<f83790f0>] ? ieee80211_scan_work+0x0/0x4b0 [mac80211]
[ 177.440454] [<c0168600>] ? autoremove_wake_function+0x0/0x50
[ 177.440463] [<c0163880>] ? worker_thread+0x0/0x200
[ 177.440471] [<c01682b4>] kthread+0x74/0x80
[ 177.440479] [<c0168240>] ? kthread+0x0/0x80
[ 177.440488] [<c0103c47>] kernel_thread_helper+0x7/0x10
[ 177.440494] ---[ end trace d6c0a8110c16e04b ]---
[ 177.443939] phy0: device now idle
[ 183.714141] phy0: device no longer idle - scanning
[ 187.335604] wlan0: direct probe to AP 00:0b:85:5b:a6:ec (try 1)
[ 187.338695] wlan0: direct probe responded
[ 187.338703] wlan0: authenticate with AP 00:0b:85:5b:a6:ec (try 1)
[ 187.340329] wlan0: authenticated
[ 187.340635] wlan0: associate with AP 00:0b:85:5b:a6:ec (try 1)
[ 187.343385] wlan0: RX AssocResp from 00:0b:85:5b:a6:ec (capab=0x431 status=0 aid=52)
[ 187.343392] wlan0: associated
[ 187.343401] phy0: Allocated STA 00:0b:85:5b:a6:ec
[ 187.344165] phy0: Inserted STA 00:0b:85:5b:a6:ec
[ 187.344924] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 187.345770] cfg80211: Calling CRDA for country: US
[ 187.352927] cfg80211: Received country IE:
[ 187.352935] cfg80211: Regulatory domain: US
[ 187.352939] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 187.352947] (2402000 KHz - 2477000 KHz @ 40000 KHz), (10000 mBi, 10000 mBm)
[ 187.352952] cfg80211: CRDA thinks this should applied:
[ 187.352956] cfg80211: Regulatory domain: US
[ 187.352960] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 187.352967] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 187.352974] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 187.352980] (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 187.352987] (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 187.352994] (5651000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 187.353000] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 187.353005] cfg80211: We intersect both of these and get:
[ 187.353010] cfg80211: Regulatory domain: 98
[ 187.353014] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 187.353020] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 187.353033] cfg80211: Disabling channel 2467 MHz on phy0 due to Country IE
[ 187.353038] cfg80211: Disabling channel 2472 MHz on phy0 due to Country IE
[ 187.353044] cfg80211: Disabling channel 2484 MHz on phy0 due to Country IE
[ 187.353050] cfg80211: Leaving channel 5180 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353060] wlan0: dropped frame to 00:0b:85:5b:a6:ec (unauthorized port)
[ 187.353068] cfg80211: Leaving channel 5200 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353075] cfg80211: Leaving channel 5220 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353083] cfg80211: Leaving channel 5240 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353091] cfg80211: Leaving channel 5260 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353098] cfg80211: Leaving channel 5280 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353106] cfg80211: Leaving channel 5300 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353113] cfg80211: Leaving channel 5320 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353121] cfg80211: Leaving channel 5500 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353129] cfg80211: Leaving channel 5520 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353136] cfg80211: Leaving channel 5540 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353144] cfg80211: Leaving channel 5560 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353151] cfg80211: Leaving channel 5580 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353159] cfg80211: Leaving channel 5600 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353167] cfg80211: Leaving channel 5620 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353175] cfg80211: Leaving channel 5640 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353183] cfg80211: Leaving channel 5660 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353190] cfg80211: Leaving channel 5680 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353198] cfg80211: Leaving channel 5700 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353205] cfg80211: Leaving channel 5745 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353213] cfg80211: Leaving channel 5765 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353221] cfg80211: Leaving channel 5785 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353228] cfg80211: Leaving channel 5805 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353236] cfg80211: Leaving channel 5825 MHz intact on phy0 - no rule found in band on Country IE
[ 187.353253] cfg80211: Current regulatory domain updated by AP to: US
[ 187.353258] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 187.353265] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 187.805098] wlan0: dropped frame to 00:0b:85:5b:a6:ec (unauthorized port)
[ 188.804121] wlan0: dropped frame to 00:0b:85:5b:a6:ec (unauthorized port)
[ 191.290511] wlan0: deauthenticated from 00:0b:85:5b:a6:ec (Reason: 1)
[ 191.290536] phy0: device now idle
[ 191.290573] phy0: Removed STA 00:0b:85:5b:a6:ec
[ 191.321556] phy0: Destroyed STA 00:0b:85:5b:a6:ec
[ 191.421927] phy0: device no longer idle - scanning
[ 194.672155] wlan0: direct probe to AP 00:0b:85:5b:a6:e3 (try 1)
[ 194.673139] wlan0: direct probe responded
[ 194.673146] wlan0: authenticate with AP 00:0b:85:5b:a6:e3 (try 1)
[ 194.674160] wlan0: authenticated
[ 194.674494] wlan0: associate with AP 00:0b:85:5b:a6:e3 (try 1)
[ 194.677426] wlan0: RX AssocResp from 00:0b:85:5b:a6:e3 (capab=0x11 status=0 aid=70)
[ 194.677433] wlan0: associated
[ 194.677442] phy0: Allocated STA 00:0b:85:5b:a6:e3
[ 194.677931] phy0: Inserted STA 00:0b:85:5b:a6:e3
[ 196.804059] wlan0: dropped frame to 00:0b:85:5b:a6:e3 (unauthorized port)
[ 197.689989] wlan0: deauthenticated from 00:0b:85:5b:a6:e3 (Reason: 1)
[ 197.690012] phy0: device now idle
[ 197.690047] phy0: Removed STA 00:0b:85:5b:a6:e3
[ 197.717474] phy0: Destroyed STA 00:0b:85:5b:a6:e3
[ 197.805059] wlan0: no IPv6 routers present
[ 197.818000] phy0: device no longer idle - scanning
[ 201.079270] phy0: device now idle
[ 201.084747] phy0: device no longer idle - in use
[ 201.084770] wlan0: direct probe to AP 00:0b:85:5b:a6:ec (try 1)
[ 201.089664] wlan0: direct probe responded
[ 201.089668] wlan0: authenticate with AP 00:0b:85:5b:a6:ec (try 1)
[ 201.092158] wlan0: authenticated
[ 201.092452] wlan0: associate with AP 00:0b:85:5b:a6:ec (try 1)
[ 201.096074] wlan0: RX AssocResp from 00:0b:85:5b:a6:ec (capab=0x431 status=0 aid=52)
[ 201.096081] wlan0: associated
[ 201.096090] phy0: Allocated STA 00:0b:85:5b:a6:ec
[ 201.096552] phy0: Inserted STA 00:0b:85:5b:a6:ec
[ 204.093552] wlan0: deauthenticated from 00:0b:85:5b:a6:ec (Reason: 1)
[ 204.093575] phy0: device now idle
[ 204.093612] phy0: Removed STA 00:0b:85:5b:a6:ec
[ 204.113479] phy0: Destroyed STA 00:0b:85:5b:a6:ec
[ 204.214013] phy0: device no longer idle - scanning
[ 207.471524] phy0: device now idle
[ 207.476732] phy0: device no longer idle - in use
[ 207.476756] wlan0: direct probe to AP 00:0b:85:5b:a6:e3 (try 1)
[ 207.477684] wlan0: direct probe responded
[ 207.477687] wlan0: authenticate with AP 00:0b:85:5b:a6:e3 (try 1)
[ 207.479033] wlan0: authenticated
[ 207.479171] wlan0: associate with AP 00:0b:85:5b:a6:e3 (try 1)
[ 207.480744] wlan0: RX AssocResp from 00:0b:85:5b:a6:e3 (capab=0x11 status=0 aid=72)
[ 207.480748] wlan0: associated
[ 207.480752] phy0: Allocated STA 00:0b:85:5b:a6:e3
[ 207.480965] phy0: Inserted STA 00:0b:85:5b:a6:e3
[ 210.489907] wlan0: deauthenticated from 00:0b:85:5b:a6:e3 (Reason: 1)
[ 210.489930] phy0: device now idle
[ 210.489968] phy0: Removed STA 00:0b:85:5b:a6:e3
[ 210.521484] phy0: Destroyed STA 00:0b:85:5b:a6:e3
[ 210.621987] phy0: device no longer idle - scanning
[ 213.876178] phy0: device now idle
[ 213.879982] phy0: device no longer idle - in use
[ 213.880004] wlan0: direct probe to AP 00:0b:85:5b:8d:6c (try 1)
[ 214.080136] wlan0: direct probe to AP 00:0b:85:5b:8d:6c (try 2)
[ 214.089058] wlan0: direct probe responded
[ 214.089066] wlan0: authenticate with AP 00:0b:85:5b:8d:6c (try 1)
[ 214.107502] wlan0: authenticated
[ 214.107916] wlan0: associate with AP 00:0b:85:5b:8d:6c (try 1)
[ 214.122278] wlan0: RX AssocResp from 00:0b:85:5b:8d:6c (capab=0x401 status=17 aid=0)
[ 214.122285] wlan0: AP denied association (code=17)
Luis
next reply other threads:[~2009-10-28 18:37 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-10-28 18:37 Luis R. Rodriguez [this message]
2009-10-28 18:47 ` odd state reached when AP deauths you after assoc Luis R. Rodriguez
2009-10-28 20:24 ` Johannes Berg
2009-10-29 20:55 ` Luis R. Rodriguez
2009-10-29 21:19 ` Luis R. Rodriguez
2009-10-29 21:28 ` Johannes Berg
2009-10-29 21:33 ` Luis R. Rodriguez
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20091028183726.GA4952@tux \
--to=lrodriguez@atheros.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.