From: marek.vasut@gmail.com (Marek Vasut)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/3] ARM: pxa/raumfeld: add platform support
Date: Thu, 26 Nov 2009 20:13:47 +0100 [thread overview]
Message-ID: <200911262013.47713.marek.vasut@gmail.com> (raw)
In-Reply-To: <1259258341-31114-2-git-send-email-daniel@caiaq.de>
Dne ?t 26. listopadu 2009 18:58:59 Daniel Mack napsal(a):
> This adds support for Raumfeld's 'Controller', 'Connector', 'Speaker S'
> and 'Speaker M' devices. They're all based on PXA303 SoCs.
>
> Signed-off-by: Daniel Mack <daniel@caiaq.de>
> ---
...
> +/*
> + * GPIO configurations
> + */
> +static mfp_cfg_t __raumfeld_controller_pin_config[] = {
> + /* UART1 */
> + GPIO77_UART1_RXD,
> + GPIO78_UART1_TXD,
> + GPIO79_UART1_CTS,
> + GPIO81_UART1_DSR,
> + GPIO83_UART1_DTR,
> + GPIO84_UART1_RTS,
> +
> + /* UART3 */
> + GPIO110_UART3_RXD,
> +
> + /* USB Host */
> + GPIO0_2_USBH_PEN,
> + GPIO1_2_USBH_PWR,
> +
> + /* I2C */
> + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> +
> + /* SPI */
> + GPIO34_GPIO, /* SPDIF_CS */
> + GPIO96_GPIO, /* MCLK_CS */
> + GPIO125_GPIO, /* ACCEL_CS */
> +
> + /* MMC */
> + GPIO3_MMC1_DAT0,
> + GPIO4_MMC1_DAT1,
> + GPIO5_MMC1_DAT2,
> + GPIO6_MMC1_DAT3,
> + GPIO7_MMC1_CLK,
> + GPIO8_MMC1_CMD,
> +
> + /* One-wire */
> + GPIO126_GPIO | MFP_LPM_FLOAT,
> + GPIO105_GPIO | MFP_PULL_LOW | MFP_LPM_PULL_LOW,
> +
> + /* CHRG_USB_OK */
> + GPIO101_GPIO | MFP_PULL_HIGH,
> + /* CHRG_USB_OK */
> + GPIO112_GPIO | MFP_PULL_HIGH,
> + /* CHRG_USB_SUSP */
> + GPIO102_GPIO,
> + /* DISPLAY_ENABLE */
> + GPIO106_GPIO,
> + /* DOCK_DETECT */
> + GPIO116_GPIO | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> +
> + /* LCD */
> + GPIO54_LCD_LDD_0,
> + GPIO55_LCD_LDD_1,
> + GPIO56_LCD_LDD_2,
> + GPIO57_LCD_LDD_3,
> + GPIO58_LCD_LDD_4,
> + GPIO59_LCD_LDD_5,
> + GPIO60_LCD_LDD_6,
> + GPIO61_LCD_LDD_7,
> + GPIO62_LCD_LDD_8,
> + GPIO63_LCD_LDD_9,
> + GPIO64_LCD_LDD_10,
> + GPIO65_LCD_LDD_11,
> + GPIO66_LCD_LDD_12,
> + GPIO67_LCD_LDD_13,
> + GPIO68_LCD_LDD_14,
> + GPIO69_LCD_LDD_15,
> + GPIO70_LCD_LDD_16,
> + GPIO71_LCD_LDD_17,
> + GPIO72_LCD_FCLK,
> + GPIO73_LCD_LCLK,
> + GPIO74_LCD_PCLK,
> + GPIO75_LCD_BIAS,
> +};
> +
> +static mfp_cfg_t __raumfeld_connector_pin_config[] = {
> + /* UART1 */
> + GPIO77_UART1_RXD,
> + GPIO78_UART1_TXD,
> + GPIO79_UART1_CTS,
> + GPIO81_UART1_DSR,
> + GPIO83_UART1_DTR,
> + GPIO84_UART1_RTS,
> +
> + /* UART3 */
> + GPIO110_UART3_RXD,
> +
> + /* USB Host */
> + GPIO0_2_USBH_PEN,
> + GPIO1_2_USBH_PWR,
> +
> + /* I2C */
> + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> +
> + /* SPI */
> + GPIO34_GPIO, /* SPDIF_CS */
> + GPIO96_GPIO, /* MCLK_CS */
> + GPIO125_GPIO, /* ACCEL_CS */
> +
> + /* MMC */
> + GPIO3_MMC1_DAT0,
> + GPIO4_MMC1_DAT1,
> + GPIO5_MMC1_DAT2,
> + GPIO6_MMC1_DAT3,
> + GPIO7_MMC1_CLK,
> + GPIO8_MMC1_CMD,
> +
> + /* Ethernet */
> + GPIO1_nCS2, /* CS */
> + GPIO40_GPIO | MFP_PULL_HIGH, /* IRQ */
> +
> + /* SSP for I2S */
> + GPIO85_SSP1_SCLK,
> + GPIO89_SSP1_EXTCLK,
> + GPIO86_SSP1_FRM,
> + GPIO87_SSP1_TXD,
> + GPIO88_SSP1_RXD,
> + GPIO90_SSP1_SYSCLK,
> +
> + /* SSP2 for S/PDIF */
> + GPIO25_SSP2_SCLK,
> + GPIO26_SSP2_FRM,
> + GPIO27_SSP2_TXD,
> + GPIO29_SSP2_EXTCLK,
> +};
> +
> +static mfp_cfg_t __raumfeld_speaker_pin_config[] = {
> + /* UART1 */
> + GPIO77_UART1_RXD,
> + GPIO78_UART1_TXD,
> + GPIO79_UART1_CTS,
> + GPIO81_UART1_DSR,
> + GPIO83_UART1_DTR,
> + GPIO84_UART1_RTS,
> +
> + /* UART3 */
> + GPIO110_UART3_RXD,
> +
> + /* USB Host */
> + GPIO0_2_USBH_PEN,
> + GPIO1_2_USBH_PWR,
> +
> + /* I2C */
> + GPIO21_I2C_SCL | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> + GPIO22_I2C_SDA | MFP_LPM_FLOAT | MFP_PULL_FLOAT,
> +
> + /* SPI */
> + GPIO34_GPIO, /* SPDIF_CS */
> + GPIO96_GPIO, /* MCLK_CS */
> + GPIO125_GPIO, /* ACCEL_CS */
> +
> + /* MMC */
> + GPIO3_MMC1_DAT0,
> + GPIO4_MMC1_DAT1,
> + GPIO5_MMC1_DAT2,
> + GPIO6_MMC1_DAT3,
> + GPIO7_MMC1_CLK,
> + GPIO8_MMC1_CMD,
> +
> + /* Ethernet */
> + GPIO1_nCS2, /* CS */
> + GPIO40_GPIO | MFP_PULL_HIGH, /* IRQ */
> +
> + /* SSP for I2S */
> + GPIO85_SSP1_SCLK,
> + GPIO89_SSP1_EXTCLK,
> + GPIO86_SSP1_FRM,
> + GPIO87_SSP1_TXD,
> + GPIO88_SSP1_RXD,
> + GPIO90_SSP1_SYSCLK,
> +};
> +
> +/*
...
Why don't we separate the common MFP configuration into another table as some
platforms do ? The code duplication is horrible here ...
next prev parent reply other threads:[~2009-11-26 19:13 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-11-26 17:58 ARM: pxa: add support for Raumfeld audio devices [v2] Daniel Mack
2009-11-26 17:58 ` [PATCH 1/3] ARM: pxa/raumfeld: add platform support Daniel Mack
2009-11-26 17:59 ` [PATCH 2/3] ALSA: ARM: add Raumfeld audio support Daniel Mack
2009-11-26 17:59 ` Daniel Mack
2009-11-26 17:59 ` [PATCH 3/3] ARM: pxa/raumfeld: Add defconfig Daniel Mack
2009-11-27 11:34 ` [PATCH 2/3] ALSA: ARM: add Raumfeld audio support Mark Brown
2009-11-27 11:34 ` Mark Brown
2009-11-27 12:42 ` Daniel Mack
2009-11-27 12:42 ` Daniel Mack
2009-11-26 19:13 ` Marek Vasut [this message]
2009-11-26 19:17 ` [PATCH 1/3] ARM: pxa/raumfeld: add platform support Daniel Mack
2009-11-26 19:18 ` Russell King - ARM Linux
2009-11-26 22:11 ` Marek Vasut
2009-11-26 22:19 ` Russell King - ARM Linux
2009-11-27 1:49 ` Marek Vasut
2009-11-27 8:50 ` Russell King - ARM Linux
2009-11-27 5:46 ` Eric Miao
2009-11-27 10:27 ` Daniel Mack
-- strict thread matches above, loose matches on Subject: below --
2009-11-27 12:47 ARM: pxa: add support for Raumfeld audio devices [v3] Daniel Mack
2009-11-27 12:47 ` [PATCH 1/3] ARM: pxa/raumfeld: add platform support Daniel Mack
2009-11-29 3:19 ` Eric Miao
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200911262013.47713.marek.vasut@gmail.com \
--to=marek.vasut@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.