[Qemu-devel] [PATCH V2 00/10] various pci clean ups.

[Qemu-devel] [PATCH V2 00/10] various pci clean ups.

[Isaku Yamahata]

This patch series is for various somewhat atrandom clean up.

- the patch "piix_pci: define symbolic value for PAM0, PAM6 and SMRAM."
  doesn't cause binary difference.
  I checked the piix_pci.o binary doesn't changed with the patch applied
  or not by diffing results of disassembling object files.

- rebased to MST's git tree
git://git.kernel.org/pub/scm/linux/kernel/git/mst/qemu.git pci.
Anyway the only patch "pci: use pci_regs.h" 4 patch conflicts.
So I expect all but the patch "pci: use pci_regs.h" can applies to
unstable tree. And it's trivial to resolve the conflict.

changes v1 -> v2:
- dropped the patch "pci: clean up pci_bar_address()"
- reordered
- rebased to git://git.kernel.org/pub/scm/linux/kernel/git/mst/qemu.git pci
- updated I440FX patch.
- added link to I440FX link

Isaku Yamahata (10):
  pci: remove PCIBus::config_reg.
  pci: s/PCI_SUBVENDOR_ID/PCI_SUBSYSTEM_VENDOR_ID/g
  pci: import Linux pci_regs.h
  pci: use pci_regs.h
  gt64xxx: remove gt64120_{read, write}_config().
  acpi: use range helper function.
  msix: use range helper function.
  piix_pci: define symbolic value for PAM0, PAM6 and SMRAM.
  piix_pci: use range helper function
  piix_pci: add link to i440fx data sheet.

 hw/acpi.c     |    2 +-
 hw/gt64xxx.c  |   13 +-
 hw/msix.c     |    2 +-
 hw/pci.c      |    3 +-
 hw/pci.h      |   77 +-------
 hw/pci_regs.h |  665 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 hw/piix_pci.c |   22 ++-
 7 files changed, 689 insertions(+), 95 deletions(-)
 create mode 100644 hw/pci_regs.h

[Qemu-devel] [PATCH V2 01/10] pci: remove PCIBus::config_reg.

[Isaku Yamahata]

PCIBus::config_reg isn't used anymore, so remove it.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
---
 hw/pci.c |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)

diff --git a/hw/pci.c b/hw/pci.c
index 404eead..aed3a24 100644
--- a/hw/pci.c
+++ b/hw/pci.c
@@ -40,7 +40,6 @@ struct PCIBus {
     pci_set_irq_fn set_irq;
     pci_map_irq_fn map_irq;
     pci_hotplug_fn hotplug;
-    uint32_t config_reg; /* XXX: suppress */
     void *irq_opaque;
     PCIDevice *devices[256];
     PCIDevice *parent_dev;
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 02/10] pci: s/PCI_SUBVENDOR_ID/PCI_SUBSYSTEM_VENDOR_ID/g

[Isaku Yamahata]

To match Linux PCI register definition,
rename PCI_SUBVENDOR_ID to PCI_SUBSYSTEM_VENDOR_ID.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
---
 hw/pci.c |    2 +-
 hw/pci.h |    2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/hw/pci.c b/hw/pci.c
index aed3a24..c4688af 100644
--- a/hw/pci.c
+++ b/hw/pci.c
@@ -411,7 +411,7 @@ static int pci_set_default_subsystem_id(PCIDevice *pci_dev)
 {
     uint16_t *id;
 
-    id = (void*)(&pci_dev->config[PCI_SUBVENDOR_ID]);
+    id = (void*)(&pci_dev->config[PCI_SUBSYSTEM_VENDOR_ID]);
     id[0] = cpu_to_le16(pci_default_sub_vendor_id);
     id[1] = cpu_to_le16(pci_default_sub_device_id);
     return 0;
diff --git a/hw/pci.h b/hw/pci.h
index 475b044..3be7a99 100644
--- a/hw/pci.h
+++ b/hw/pci.h
@@ -155,7 +155,7 @@ typedef struct PCIIORegion {
 #define PCI_CAP_LIST_NEXT	1	/* Next capability in the list */
 
 #define PCI_REVISION            0x08    /* obsolete, use PCI_REVISION_ID */
-#define PCI_SUBVENDOR_ID        0x2c    /* obsolete, use PCI_SUBSYSTEM_VENDOR_ID */
+#define PCI_SUBSYSTEM_VENDOR_ID 0x2c
 #define PCI_SUBDEVICE_ID        0x2e    /* obsolete, use PCI_SUBSYSTEM_ID */
 
 /* Bits in the PCI Status Register (PCI 2.3 spec) */
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 03/10] pci: import Linux pci_regs.h

[Isaku Yamahata]

Import Linux pci_regs.h. Later PCI register definitions in pci.h
will be eliminated.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
---
 hw/pci_regs.h |  665 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 665 insertions(+), 0 deletions(-)
 create mode 100644 hw/pci_regs.h

diff --git a/hw/pci_regs.h b/hw/pci_regs.h
new file mode 100644
index 0000000..dd0bed4
--- /dev/null
+++ b/hw/pci_regs.h
@@ -0,0 +1,665 @@
+/*
+ *	pci_regs.h
+ *
+ *	PCI standard defines
+ *	Copyright 1994, Drew Eckhardt
+ *	Copyright 1997--1999 Martin Mares <mj@ucw.cz>
+ *
+ *	For more information, please consult the following manuals (look at
+ *	http://www.pcisig.com/ for how to get them):
+ *
+ *	PCI BIOS Specification
+ *	PCI Local Bus Specification
+ *	PCI to PCI Bridge Specification
+ *	PCI System Design Guide
+ *
+ * 	For hypertransport information, please consult the following manuals
+ * 	from http://www.hypertransport.org
+ *
+ *	The Hypertransport I/O Link Specification
+ */
+
+#ifndef LINUX_PCI_REGS_H
+#define LINUX_PCI_REGS_H
+
+/*
+ * Under PCI, each device has 256 bytes of configuration address space,
+ * of which the first 64 bytes are standardized as follows:
+ */
+#define PCI_VENDOR_ID		0x00	/* 16 bits */
+#define PCI_DEVICE_ID		0x02	/* 16 bits */
+#define PCI_COMMAND		0x04	/* 16 bits */
+#define  PCI_COMMAND_IO		0x1	/* Enable response in I/O space */
+#define  PCI_COMMAND_MEMORY	0x2	/* Enable response in Memory space */
+#define  PCI_COMMAND_MASTER	0x4	/* Enable bus mastering */
+#define  PCI_COMMAND_SPECIAL	0x8	/* Enable response to special cycles */
+#define  PCI_COMMAND_INVALIDATE	0x10	/* Use memory write and invalidate */
+#define  PCI_COMMAND_VGA_PALETTE 0x20	/* Enable palette snooping */
+#define  PCI_COMMAND_PARITY	0x40	/* Enable parity checking */
+#define  PCI_COMMAND_WAIT 	0x80	/* Enable address/data stepping */
+#define  PCI_COMMAND_SERR	0x100	/* Enable SERR */
+#define  PCI_COMMAND_FAST_BACK	0x200	/* Enable back-to-back writes */
+#define  PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */
+
+#define PCI_STATUS		0x06	/* 16 bits */
+#define  PCI_STATUS_INTERRUPT	0x08	/* Interrupt status */
+#define  PCI_STATUS_CAP_LIST	0x10	/* Support Capability List */
+#define  PCI_STATUS_66MHZ	0x20	/* Support 66 Mhz PCI 2.1 bus */
+#define  PCI_STATUS_UDF		0x40	/* Support User Definable Features [obsolete] */
+#define  PCI_STATUS_FAST_BACK	0x80	/* Accept fast-back to back */
+#define  PCI_STATUS_PARITY	0x100	/* Detected parity error */
+#define  PCI_STATUS_DEVSEL_MASK	0x600	/* DEVSEL timing */
+#define  PCI_STATUS_DEVSEL_FAST		0x000
+#define  PCI_STATUS_DEVSEL_MEDIUM	0x200
+#define  PCI_STATUS_DEVSEL_SLOW		0x400
+#define  PCI_STATUS_SIG_TARGET_ABORT	0x800 /* Set on target abort */
+#define  PCI_STATUS_REC_TARGET_ABORT	0x1000 /* Master ack of " */
+#define  PCI_STATUS_REC_MASTER_ABORT	0x2000 /* Set on master abort */
+#define  PCI_STATUS_SIG_SYSTEM_ERROR	0x4000 /* Set when we drive SERR */
+#define  PCI_STATUS_DETECTED_PARITY	0x8000 /* Set on parity error */
+
+#define PCI_CLASS_REVISION	0x08	/* High 24 bits are class, low 8 revision */
+#define PCI_REVISION_ID		0x08	/* Revision ID */
+#define PCI_CLASS_PROG		0x09	/* Reg. Level Programming Interface */
+#define PCI_CLASS_DEVICE	0x0a	/* Device class */
+
+#define PCI_CACHE_LINE_SIZE	0x0c	/* 8 bits */
+#define PCI_LATENCY_TIMER	0x0d	/* 8 bits */
+#define PCI_HEADER_TYPE		0x0e	/* 8 bits */
+#define  PCI_HEADER_TYPE_NORMAL		0
+#define  PCI_HEADER_TYPE_BRIDGE		1
+#define  PCI_HEADER_TYPE_CARDBUS	2
+
+#define PCI_BIST		0x0f	/* 8 bits */
+#define  PCI_BIST_CODE_MASK	0x0f	/* Return result */
+#define  PCI_BIST_START		0x40	/* 1 to start BIST, 2 secs or less */
+#define  PCI_BIST_CAPABLE	0x80	/* 1 if BIST capable */
+
+/*
+ * Base addresses specify locations in memory or I/O space.
+ * Decoded size can be determined by writing a value of
+ * 0xffffffff to the register, and reading it back.  Only
+ * 1 bits are decoded.
+ */
+#define PCI_BASE_ADDRESS_0	0x10	/* 32 bits */
+#define PCI_BASE_ADDRESS_1	0x14	/* 32 bits [htype 0,1 only] */
+#define PCI_BASE_ADDRESS_2	0x18	/* 32 bits [htype 0 only] */
+#define PCI_BASE_ADDRESS_3	0x1c	/* 32 bits */
+#define PCI_BASE_ADDRESS_4	0x20	/* 32 bits */
+#define PCI_BASE_ADDRESS_5	0x24	/* 32 bits */
+#define  PCI_BASE_ADDRESS_SPACE		0x01	/* 0 = memory, 1 = I/O */
+#define  PCI_BASE_ADDRESS_SPACE_IO	0x01
+#define  PCI_BASE_ADDRESS_SPACE_MEMORY	0x00
+#define  PCI_BASE_ADDRESS_MEM_TYPE_MASK	0x06
+#define  PCI_BASE_ADDRESS_MEM_TYPE_32	0x00	/* 32 bit address */
+#define  PCI_BASE_ADDRESS_MEM_TYPE_1M	0x02	/* Below 1M [obsolete] */
+#define  PCI_BASE_ADDRESS_MEM_TYPE_64	0x04	/* 64 bit address */
+#define  PCI_BASE_ADDRESS_MEM_PREFETCH	0x08	/* prefetchable? */
+#define  PCI_BASE_ADDRESS_MEM_MASK	(~0x0fUL)
+#define  PCI_BASE_ADDRESS_IO_MASK	(~0x03UL)
+/* bit 1 is reserved if address_space = 1 */
+
+/* Header type 0 (normal devices) */
+#define PCI_CARDBUS_CIS		0x28
+#define PCI_SUBSYSTEM_VENDOR_ID	0x2c
+#define PCI_SUBSYSTEM_ID	0x2e
+#define PCI_ROM_ADDRESS		0x30	/* Bits 31..11 are address, 10..1 reserved */
+#define  PCI_ROM_ADDRESS_ENABLE	0x01
+#define PCI_ROM_ADDRESS_MASK	(~0x7ffUL)
+
+#define PCI_CAPABILITY_LIST	0x34	/* Offset of first capability list entry */
+
+/* 0x35-0x3b are reserved */
+#define PCI_INTERRUPT_LINE	0x3c	/* 8 bits */
+#define PCI_INTERRUPT_PIN	0x3d	/* 8 bits */
+#define PCI_MIN_GNT		0x3e	/* 8 bits */
+#define PCI_MAX_LAT		0x3f	/* 8 bits */
+
+/* Header type 1 (PCI-to-PCI bridges) */
+#define PCI_PRIMARY_BUS		0x18	/* Primary bus number */
+#define PCI_SECONDARY_BUS	0x19	/* Secondary bus number */
+#define PCI_SUBORDINATE_BUS	0x1a	/* Highest bus number behind the bridge */
+#define PCI_SEC_LATENCY_TIMER	0x1b	/* Latency timer for secondary interface */
+#define PCI_IO_BASE		0x1c	/* I/O range behind the bridge */
+#define PCI_IO_LIMIT		0x1d
+#define  PCI_IO_RANGE_TYPE_MASK	0x0fUL	/* I/O bridging type */
+#define  PCI_IO_RANGE_TYPE_16	0x00
+#define  PCI_IO_RANGE_TYPE_32	0x01
+#define  PCI_IO_RANGE_MASK	(~0x0fUL)
+#define PCI_SEC_STATUS		0x1e	/* Secondary status register, only bit 14 used */
+#define PCI_MEMORY_BASE		0x20	/* Memory range behind */
+#define PCI_MEMORY_LIMIT	0x22
+#define  PCI_MEMORY_RANGE_TYPE_MASK 0x0fUL
+#define  PCI_MEMORY_RANGE_MASK	(~0x0fUL)
+#define PCI_PREF_MEMORY_BASE	0x24	/* Prefetchable memory range behind */
+#define PCI_PREF_MEMORY_LIMIT	0x26
+#define  PCI_PREF_RANGE_TYPE_MASK 0x0fUL
+#define  PCI_PREF_RANGE_TYPE_32	0x00
+#define  PCI_PREF_RANGE_TYPE_64	0x01
+#define  PCI_PREF_RANGE_MASK	(~0x0fUL)
+#define PCI_PREF_BASE_UPPER32	0x28	/* Upper half of prefetchable memory range */
+#define PCI_PREF_LIMIT_UPPER32	0x2c
+#define PCI_IO_BASE_UPPER16	0x30	/* Upper half of I/O addresses */
+#define PCI_IO_LIMIT_UPPER16	0x32
+/* 0x34 same as for htype 0 */
+/* 0x35-0x3b is reserved */
+#define PCI_ROM_ADDRESS1	0x38	/* Same as PCI_ROM_ADDRESS, but for htype 1 */
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_BRIDGE_CONTROL	0x3e
+#define  PCI_BRIDGE_CTL_PARITY	0x01	/* Enable parity detection on secondary interface */
+#define  PCI_BRIDGE_CTL_SERR	0x02	/* The same for SERR forwarding */
+#define  PCI_BRIDGE_CTL_ISA	0x04	/* Enable ISA mode */
+#define  PCI_BRIDGE_CTL_VGA	0x08	/* Forward VGA addresses */
+#define  PCI_BRIDGE_CTL_MASTER_ABORT	0x20  /* Report master aborts */
+#define  PCI_BRIDGE_CTL_BUS_RESET	0x40	/* Secondary bus reset */
+#define  PCI_BRIDGE_CTL_FAST_BACK	0x80	/* Fast Back2Back enabled on secondary interface */
+
+/* Header type 2 (CardBus bridges) */
+#define PCI_CB_CAPABILITY_LIST	0x14
+/* 0x15 reserved */
+#define PCI_CB_SEC_STATUS	0x16	/* Secondary status */
+#define PCI_CB_PRIMARY_BUS	0x18	/* PCI bus number */
+#define PCI_CB_CARD_BUS		0x19	/* CardBus bus number */
+#define PCI_CB_SUBORDINATE_BUS	0x1a	/* Subordinate bus number */
+#define PCI_CB_LATENCY_TIMER	0x1b	/* CardBus latency timer */
+#define PCI_CB_MEMORY_BASE_0	0x1c
+#define PCI_CB_MEMORY_LIMIT_0	0x20
+#define PCI_CB_MEMORY_BASE_1	0x24
+#define PCI_CB_MEMORY_LIMIT_1	0x28
+#define PCI_CB_IO_BASE_0	0x2c
+#define PCI_CB_IO_BASE_0_HI	0x2e
+#define PCI_CB_IO_LIMIT_0	0x30
+#define PCI_CB_IO_LIMIT_0_HI	0x32
+#define PCI_CB_IO_BASE_1	0x34
+#define PCI_CB_IO_BASE_1_HI	0x36
+#define PCI_CB_IO_LIMIT_1	0x38
+#define PCI_CB_IO_LIMIT_1_HI	0x3a
+#define  PCI_CB_IO_RANGE_MASK	(~0x03UL)
+/* 0x3c-0x3d are same as for htype 0 */
+#define PCI_CB_BRIDGE_CONTROL	0x3e
+#define  PCI_CB_BRIDGE_CTL_PARITY	0x01	/* Similar to standard bridge control register */
+#define  PCI_CB_BRIDGE_CTL_SERR		0x02
+#define  PCI_CB_BRIDGE_CTL_ISA		0x04
+#define  PCI_CB_BRIDGE_CTL_VGA		0x08
+#define  PCI_CB_BRIDGE_CTL_MASTER_ABORT	0x20
+#define  PCI_CB_BRIDGE_CTL_CB_RESET	0x40	/* CardBus reset */
+#define  PCI_CB_BRIDGE_CTL_16BIT_INT	0x80	/* Enable interrupt for 16-bit cards */
+#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM0 0x100	/* Prefetch enable for both memory regions */
+#define  PCI_CB_BRIDGE_CTL_PREFETCH_MEM1 0x200
+#define  PCI_CB_BRIDGE_CTL_POST_WRITES	0x400
+#define PCI_CB_SUBSYSTEM_VENDOR_ID	0x40
+#define PCI_CB_SUBSYSTEM_ID		0x42
+#define PCI_CB_LEGACY_MODE_BASE		0x44	/* 16-bit PC Card legacy mode base address (ExCa) */
+/* 0x48-0x7f reserved */
+
+/* Capability lists */
+
+#define PCI_CAP_LIST_ID		0	/* Capability ID */
+#define  PCI_CAP_ID_PM		0x01	/* Power Management */
+#define  PCI_CAP_ID_AGP		0x02	/* Accelerated Graphics Port */
+#define  PCI_CAP_ID_VPD		0x03	/* Vital Product Data */
+#define  PCI_CAP_ID_SLOTID	0x04	/* Slot Identification */
+#define  PCI_CAP_ID_MSI		0x05	/* Message Signalled Interrupts */
+#define  PCI_CAP_ID_CHSWP	0x06	/* CompactPCI HotSwap */
+#define  PCI_CAP_ID_PCIX	0x07	/* PCI-X */
+#define  PCI_CAP_ID_HT		0x08	/* HyperTransport */
+#define  PCI_CAP_ID_VNDR	0x09	/* Vendor specific */
+#define  PCI_CAP_ID_DBG		0x0A	/* Debug port */
+#define  PCI_CAP_ID_CCRC	0x0B	/* CompactPCI Central Resource Control */
+#define  PCI_CAP_ID_SHPC 	0x0C	/* PCI Standard Hot-Plug Controller */
+#define  PCI_CAP_ID_SSVID	0x0D	/* Bridge subsystem vendor/device ID */
+#define  PCI_CAP_ID_AGP3	0x0E	/* AGP Target PCI-PCI bridge */
+#define  PCI_CAP_ID_EXP 	0x10	/* PCI Express */
+#define  PCI_CAP_ID_MSIX	0x11	/* MSI-X */
+#define  PCI_CAP_ID_AF		0x13	/* PCI Advanced Features */
+#define PCI_CAP_LIST_NEXT	1	/* Next capability in the list */
+#define PCI_CAP_FLAGS		2	/* Capability defined flags (16 bits) */
+#define PCI_CAP_SIZEOF		4
+
+/* Power Management Registers */
+
+#define PCI_PM_PMC		2	/* PM Capabilities Register */
+#define  PCI_PM_CAP_VER_MASK	0x0007	/* Version */
+#define  PCI_PM_CAP_PME_CLOCK	0x0008	/* PME clock required */
+#define  PCI_PM_CAP_RESERVED    0x0010  /* Reserved field */
+#define  PCI_PM_CAP_DSI		0x0020	/* Device specific initialization */
+#define  PCI_PM_CAP_AUX_POWER	0x01C0	/* Auxilliary power support mask */
+#define  PCI_PM_CAP_D1		0x0200	/* D1 power state support */
+#define  PCI_PM_CAP_D2		0x0400	/* D2 power state support */
+#define  PCI_PM_CAP_PME		0x0800	/* PME pin supported */
+#define  PCI_PM_CAP_PME_MASK	0xF800	/* PME Mask of all supported states */
+#define  PCI_PM_CAP_PME_D0	0x0800	/* PME# from D0 */
+#define  PCI_PM_CAP_PME_D1	0x1000	/* PME# from D1 */
+#define  PCI_PM_CAP_PME_D2	0x2000	/* PME# from D2 */
+#define  PCI_PM_CAP_PME_D3	0x4000	/* PME# from D3 (hot) */
+#define  PCI_PM_CAP_PME_D3cold	0x8000	/* PME# from D3 (cold) */
+#define  PCI_PM_CAP_PME_SHIFT	11	/* Start of the PME Mask in PMC */
+#define PCI_PM_CTRL		4	/* PM control and status register */
+#define  PCI_PM_CTRL_STATE_MASK	0x0003	/* Current power state (D0 to D3) */
+#define  PCI_PM_CTRL_NO_SOFT_RESET	0x0008	/* No reset for D3hot->D0 */
+#define  PCI_PM_CTRL_PME_ENABLE	0x0100	/* PME pin enable */
+#define  PCI_PM_CTRL_DATA_SEL_MASK	0x1e00	/* Data select (??) */
+#define  PCI_PM_CTRL_DATA_SCALE_MASK	0x6000	/* Data scale (??) */
+#define  PCI_PM_CTRL_PME_STATUS	0x8000	/* PME pin status */
+#define PCI_PM_PPB_EXTENSIONS	6	/* PPB support extensions (??) */
+#define  PCI_PM_PPB_B2_B3	0x40	/* Stop clock when in D3hot (??) */
+#define  PCI_PM_BPCC_ENABLE	0x80	/* Bus power/clock control enable (??) */
+#define PCI_PM_DATA_REGISTER	7	/* (??) */
+#define PCI_PM_SIZEOF		8
+
+/* AGP registers */
+
+#define PCI_AGP_VERSION		2	/* BCD version number */
+#define PCI_AGP_RFU		3	/* Rest of capability flags */
+#define PCI_AGP_STATUS		4	/* Status register */
+#define  PCI_AGP_STATUS_RQ_MASK	0xff000000	/* Maximum number of requests - 1 */
+#define  PCI_AGP_STATUS_SBA	0x0200	/* Sideband addressing supported */
+#define  PCI_AGP_STATUS_64BIT	0x0020	/* 64-bit addressing supported */
+#define  PCI_AGP_STATUS_FW	0x0010	/* FW transfers supported */
+#define  PCI_AGP_STATUS_RATE4	0x0004	/* 4x transfer rate supported */
+#define  PCI_AGP_STATUS_RATE2	0x0002	/* 2x transfer rate supported */
+#define  PCI_AGP_STATUS_RATE1	0x0001	/* 1x transfer rate supported */
+#define PCI_AGP_COMMAND		8	/* Control register */
+#define  PCI_AGP_COMMAND_RQ_MASK 0xff000000  /* Master: Maximum number of requests */
+#define  PCI_AGP_COMMAND_SBA	0x0200	/* Sideband addressing enabled */
+#define  PCI_AGP_COMMAND_AGP	0x0100	/* Allow processing of AGP transactions */
+#define  PCI_AGP_COMMAND_64BIT	0x0020 	/* Allow processing of 64-bit addresses */
+#define  PCI_AGP_COMMAND_FW	0x0010 	/* Force FW transfers */
+#define  PCI_AGP_COMMAND_RATE4	0x0004	/* Use 4x rate */
+#define  PCI_AGP_COMMAND_RATE2	0x0002	/* Use 2x rate */
+#define  PCI_AGP_COMMAND_RATE1	0x0001	/* Use 1x rate */
+#define PCI_AGP_SIZEOF		12
+
+/* Vital Product Data */
+
+#define PCI_VPD_ADDR		2	/* Address to access (15 bits!) */
+#define  PCI_VPD_ADDR_MASK	0x7fff	/* Address mask */
+#define  PCI_VPD_ADDR_F		0x8000	/* Write 0, 1 indicates completion */
+#define PCI_VPD_DATA		4	/* 32-bits of data returned here */
+
+/* Slot Identification */
+
+#define PCI_SID_ESR		2	/* Expansion Slot Register */
+#define  PCI_SID_ESR_NSLOTS	0x1f	/* Number of expansion slots available */
+#define  PCI_SID_ESR_FIC	0x20	/* First In Chassis Flag */
+#define PCI_SID_CHASSIS_NR	3	/* Chassis Number */
+
+/* Message Signalled Interrupts registers */
+
+#define PCI_MSI_FLAGS		2	/* Various flags */
+#define  PCI_MSI_FLAGS_64BIT	0x80	/* 64-bit addresses allowed */
+#define  PCI_MSI_FLAGS_QSIZE	0x70	/* Message queue size configured */
+#define  PCI_MSI_FLAGS_QMASK	0x0e	/* Maximum queue size available */
+#define  PCI_MSI_FLAGS_ENABLE	0x01	/* MSI feature enabled */
+#define  PCI_MSI_FLAGS_MASKBIT	0x100	/* 64-bit mask bits allowed */
+#define PCI_MSI_RFU		3	/* Rest of capability flags */
+#define PCI_MSI_ADDRESS_LO	4	/* Lower 32 bits */
+#define PCI_MSI_ADDRESS_HI	8	/* Upper 32 bits (if PCI_MSI_FLAGS_64BIT set) */
+#define PCI_MSI_DATA_32		8	/* 16 bits of data for 32-bit devices */
+#define PCI_MSI_MASK_32		12	/* Mask bits register for 32-bit devices */
+#define PCI_MSI_DATA_64		12	/* 16 bits of data for 64-bit devices */
+#define PCI_MSI_MASK_64		16	/* Mask bits register for 64-bit devices */
+
+/* MSI-X registers (these are at offset PCI_MSIX_FLAGS) */
+#define PCI_MSIX_FLAGS		2
+#define  PCI_MSIX_FLAGS_QSIZE	0x7FF
+#define  PCI_MSIX_FLAGS_ENABLE	(1 << 15)
+#define  PCI_MSIX_FLAGS_MASKALL	(1 << 14)
+#define PCI_MSIX_FLAGS_BIRMASK	(7 << 0)
+
+/* CompactPCI Hotswap Register */
+
+#define PCI_CHSWP_CSR		2	/* Control and Status Register */
+#define  PCI_CHSWP_DHA		0x01	/* Device Hiding Arm */
+#define  PCI_CHSWP_EIM		0x02	/* ENUM# Signal Mask */
+#define  PCI_CHSWP_PIE		0x04	/* Pending Insert or Extract */
+#define  PCI_CHSWP_LOO		0x08	/* LED On / Off */
+#define  PCI_CHSWP_PI		0x30	/* Programming Interface */
+#define  PCI_CHSWP_EXT		0x40	/* ENUM# status - extraction */
+#define  PCI_CHSWP_INS		0x80	/* ENUM# status - insertion */
+
+/* PCI Advanced Feature registers */
+
+#define PCI_AF_LENGTH		2
+#define PCI_AF_CAP		3
+#define  PCI_AF_CAP_TP		0x01
+#define  PCI_AF_CAP_FLR		0x02
+#define PCI_AF_CTRL		4
+#define  PCI_AF_CTRL_FLR	0x01
+#define PCI_AF_STATUS		5
+#define  PCI_AF_STATUS_TP	0x01
+
+/* PCI-X registers */
+
+#define PCI_X_CMD		2	/* Modes & Features */
+#define  PCI_X_CMD_DPERR_E	0x0001	/* Data Parity Error Recovery Enable */
+#define  PCI_X_CMD_ERO		0x0002	/* Enable Relaxed Ordering */
+#define  PCI_X_CMD_READ_512	0x0000	/* 512 byte maximum read byte count */
+#define  PCI_X_CMD_READ_1K	0x0004	/* 1Kbyte maximum read byte count */
+#define  PCI_X_CMD_READ_2K	0x0008	/* 2Kbyte maximum read byte count */
+#define  PCI_X_CMD_READ_4K	0x000c	/* 4Kbyte maximum read byte count */
+#define  PCI_X_CMD_MAX_READ	0x000c	/* Max Memory Read Byte Count */
+				/* Max # of outstanding split transactions */
+#define  PCI_X_CMD_SPLIT_1	0x0000	/* Max 1 */
+#define  PCI_X_CMD_SPLIT_2	0x0010	/* Max 2 */
+#define  PCI_X_CMD_SPLIT_3	0x0020	/* Max 3 */
+#define  PCI_X_CMD_SPLIT_4	0x0030	/* Max 4 */
+#define  PCI_X_CMD_SPLIT_8	0x0040	/* Max 8 */
+#define  PCI_X_CMD_SPLIT_12	0x0050	/* Max 12 */
+#define  PCI_X_CMD_SPLIT_16	0x0060	/* Max 16 */
+#define  PCI_X_CMD_SPLIT_32	0x0070	/* Max 32 */
+#define  PCI_X_CMD_MAX_SPLIT	0x0070	/* Max Outstanding Split Transactions */
+#define  PCI_X_CMD_VERSION(x) 	(((x) >> 12) & 3) /* Version */
+#define PCI_X_STATUS		4	/* PCI-X capabilities */
+#define  PCI_X_STATUS_DEVFN	0x000000ff	/* A copy of devfn */
+#define  PCI_X_STATUS_BUS	0x0000ff00	/* A copy of bus nr */
+#define  PCI_X_STATUS_64BIT	0x00010000	/* 64-bit device */
+#define  PCI_X_STATUS_133MHZ	0x00020000	/* 133 MHz capable */
+#define  PCI_X_STATUS_SPL_DISC	0x00040000	/* Split Completion Discarded */
+#define  PCI_X_STATUS_UNX_SPL	0x00080000	/* Unexpected Split Completion */
+#define  PCI_X_STATUS_COMPLEX	0x00100000	/* Device Complexity */
+#define  PCI_X_STATUS_MAX_READ	0x00600000	/* Designed Max Memory Read Count */
+#define  PCI_X_STATUS_MAX_SPLIT	0x03800000	/* Designed Max Outstanding Split Transactions */
+#define  PCI_X_STATUS_MAX_CUM	0x1c000000	/* Designed Max Cumulative Read Size */
+#define  PCI_X_STATUS_SPL_ERR	0x20000000	/* Rcvd Split Completion Error Msg */
+#define  PCI_X_STATUS_266MHZ	0x40000000	/* 266 MHz capable */
+#define  PCI_X_STATUS_533MHZ	0x80000000	/* 533 MHz capable */
+
+/* PCI Express capability registers */
+
+#define PCI_EXP_FLAGS		2	/* Capabilities register */
+#define PCI_EXP_FLAGS_VERS	0x000f	/* Capability version */
+#define PCI_EXP_FLAGS_TYPE	0x00f0	/* Device/Port type */
+#define  PCI_EXP_TYPE_ENDPOINT	0x0	/* Express Endpoint */
+#define  PCI_EXP_TYPE_LEG_END	0x1	/* Legacy Endpoint */
+#define  PCI_EXP_TYPE_ROOT_PORT 0x4	/* Root Port */
+#define  PCI_EXP_TYPE_UPSTREAM	0x5	/* Upstream Port */
+#define  PCI_EXP_TYPE_DOWNSTREAM 0x6	/* Downstream Port */
+#define  PCI_EXP_TYPE_PCI_BRIDGE 0x7	/* PCI/PCI-X Bridge */
+#define  PCI_EXP_TYPE_RC_END	0x9	/* Root Complex Integrated Endpoint */
+#define  PCI_EXP_TYPE_RC_EC	0x10	/* Root Complex Event Collector */
+#define PCI_EXP_FLAGS_SLOT	0x0100	/* Slot implemented */
+#define PCI_EXP_FLAGS_IRQ	0x3e00	/* Interrupt message number */
+#define PCI_EXP_DEVCAP		4	/* Device capabilities */
+#define  PCI_EXP_DEVCAP_PAYLOAD	0x07	/* Max_Payload_Size */
+#define  PCI_EXP_DEVCAP_PHANTOM	0x18	/* Phantom functions */
+#define  PCI_EXP_DEVCAP_EXT_TAG	0x20	/* Extended tags */
+#define  PCI_EXP_DEVCAP_L0S	0x1c0	/* L0s Acceptable Latency */
+#define  PCI_EXP_DEVCAP_L1	0xe00	/* L1 Acceptable Latency */
+#define  PCI_EXP_DEVCAP_ATN_BUT	0x1000	/* Attention Button Present */
+#define  PCI_EXP_DEVCAP_ATN_IND	0x2000	/* Attention Indicator Present */
+#define  PCI_EXP_DEVCAP_PWR_IND	0x4000	/* Power Indicator Present */
+#define  PCI_EXP_DEVCAP_RBER	0x8000	/* Role-Based Error Reporting */
+#define  PCI_EXP_DEVCAP_PWR_VAL	0x3fc0000 /* Slot Power Limit Value */
+#define  PCI_EXP_DEVCAP_PWR_SCL	0xc000000 /* Slot Power Limit Scale */
+#define  PCI_EXP_DEVCAP_FLR     0x10000000 /* Function Level Reset */
+#define PCI_EXP_DEVCTL		8	/* Device Control */
+#define  PCI_EXP_DEVCTL_CERE	0x0001	/* Correctable Error Reporting En. */
+#define  PCI_EXP_DEVCTL_NFERE	0x0002	/* Non-Fatal Error Reporting Enable */
+#define  PCI_EXP_DEVCTL_FERE	0x0004	/* Fatal Error Reporting Enable */
+#define  PCI_EXP_DEVCTL_URRE	0x0008	/* Unsupported Request Reporting En. */
+#define  PCI_EXP_DEVCTL_RELAX_EN 0x0010 /* Enable relaxed ordering */
+#define  PCI_EXP_DEVCTL_PAYLOAD	0x00e0	/* Max_Payload_Size */
+#define  PCI_EXP_DEVCTL_EXT_TAG	0x0100	/* Extended Tag Field Enable */
+#define  PCI_EXP_DEVCTL_PHANTOM	0x0200	/* Phantom Functions Enable */
+#define  PCI_EXP_DEVCTL_AUX_PME	0x0400	/* Auxiliary Power PM Enable */
+#define  PCI_EXP_DEVCTL_NOSNOOP_EN 0x0800  /* Enable No Snoop */
+#define  PCI_EXP_DEVCTL_READRQ	0x7000	/* Max_Read_Request_Size */
+#define  PCI_EXP_DEVCTL_BCR_FLR 0x8000  /* Bridge Configuration Retry / FLR */
+#define PCI_EXP_DEVSTA		10	/* Device Status */
+#define  PCI_EXP_DEVSTA_CED	0x01	/* Correctable Error Detected */
+#define  PCI_EXP_DEVSTA_NFED	0x02	/* Non-Fatal Error Detected */
+#define  PCI_EXP_DEVSTA_FED	0x04	/* Fatal Error Detected */
+#define  PCI_EXP_DEVSTA_URD	0x08	/* Unsupported Request Detected */
+#define  PCI_EXP_DEVSTA_AUXPD	0x10	/* AUX Power Detected */
+#define  PCI_EXP_DEVSTA_TRPND	0x20	/* Transactions Pending */
+#define PCI_EXP_LNKCAP		12	/* Link Capabilities */
+#define  PCI_EXP_LNKCAP_SLS	0x0000000f /* Supported Link Speeds */
+#define  PCI_EXP_LNKCAP_MLW	0x000003f0 /* Maximum Link Width */
+#define  PCI_EXP_LNKCAP_ASPMS	0x00000c00 /* ASPM Support */
+#define  PCI_EXP_LNKCAP_L0SEL	0x00007000 /* L0s Exit Latency */
+#define  PCI_EXP_LNKCAP_L1EL	0x00038000 /* L1 Exit Latency */
+#define  PCI_EXP_LNKCAP_CLKPM	0x00040000 /* L1 Clock Power Management */
+#define  PCI_EXP_LNKCAP_SDERC	0x00080000 /* Suprise Down Error Reporting Capable */
+#define  PCI_EXP_LNKCAP_DLLLARC	0x00100000 /* Data Link Layer Link Active Reporting Capable */
+#define  PCI_EXP_LNKCAP_LBNC	0x00200000 /* Link Bandwidth Notification Capability */
+#define  PCI_EXP_LNKCAP_PN	0xff000000 /* Port Number */
+#define PCI_EXP_LNKCTL		16	/* Link Control */
+#define  PCI_EXP_LNKCTL_ASPMC	0x0003	/* ASPM Control */
+#define  PCI_EXP_LNKCTL_RCB	0x0008	/* Read Completion Boundary */
+#define  PCI_EXP_LNKCTL_LD	0x0010	/* Link Disable */
+#define  PCI_EXP_LNKCTL_RL	0x0020	/* Retrain Link */
+#define  PCI_EXP_LNKCTL_CCC	0x0040	/* Common Clock Configuration */
+#define  PCI_EXP_LNKCTL_ES	0x0080	/* Extended Synch */
+#define  PCI_EXP_LNKCTL_CLKREQ_EN 0x100	/* Enable clkreq */
+#define  PCI_EXP_LNKCTL_HAWD	0x0200	/* Hardware Autonomous Width Disable */
+#define  PCI_EXP_LNKCTL_LBMIE	0x0400	/* Link Bandwidth Management Interrupt Enable */
+#define  PCI_EXP_LNKCTL_LABIE	0x0800	/* Lnk Autonomous Bandwidth Interrupt Enable */
+#define PCI_EXP_LNKSTA		18	/* Link Status */
+#define  PCI_EXP_LNKSTA_CLS	0x000f	/* Current Link Speed */
+#define  PCI_EXP_LNKSTA_NLW	0x03f0	/* Nogotiated Link Width */
+#define  PCI_EXP_LNKSTA_LT	0x0800	/* Link Training */
+#define  PCI_EXP_LNKSTA_SLC	0x1000	/* Slot Clock Configuration */
+#define  PCI_EXP_LNKSTA_DLLLA	0x2000	/* Data Link Layer Link Active */
+#define  PCI_EXP_LNKSTA_LBMS	0x4000	/* Link Bandwidth Management Status */
+#define  PCI_EXP_LNKSTA_LABS	0x8000	/* Link Autonomous Bandwidth Status */
+#define PCI_EXP_SLTCAP		20	/* Slot Capabilities */
+#define  PCI_EXP_SLTCAP_ABP	0x00000001 /* Attention Button Present */
+#define  PCI_EXP_SLTCAP_PCP	0x00000002 /* Power Controller Present */
+#define  PCI_EXP_SLTCAP_MRLSP	0x00000004 /* MRL Sensor Present */
+#define  PCI_EXP_SLTCAP_AIP	0x00000008 /* Attention Indicator Present */
+#define  PCI_EXP_SLTCAP_PIP	0x00000010 /* Power Indicator Present */
+#define  PCI_EXP_SLTCAP_HPS	0x00000020 /* Hot-Plug Surprise */
+#define  PCI_EXP_SLTCAP_HPC	0x00000040 /* Hot-Plug Capable */
+#define  PCI_EXP_SLTCAP_SPLV	0x00007f80 /* Slot Power Limit Value */
+#define  PCI_EXP_SLTCAP_SPLS	0x00018000 /* Slot Power Limit Scale */
+#define  PCI_EXP_SLTCAP_EIP	0x00020000 /* Electromechanical Interlock Present */
+#define  PCI_EXP_SLTCAP_NCCS	0x00040000 /* No Command Completed Support */
+#define  PCI_EXP_SLTCAP_PSN	0xfff80000 /* Physical Slot Number */
+#define PCI_EXP_SLTCTL		24	/* Slot Control */
+#define  PCI_EXP_SLTCTL_ABPE	0x0001	/* Attention Button Pressed Enable */
+#define  PCI_EXP_SLTCTL_PFDE	0x0002	/* Power Fault Detected Enable */
+#define  PCI_EXP_SLTCTL_MRLSCE	0x0004	/* MRL Sensor Changed Enable */
+#define  PCI_EXP_SLTCTL_PDCE	0x0008	/* Presence Detect Changed Enable */
+#define  PCI_EXP_SLTCTL_CCIE	0x0010	/* Command Completed Interrupt Enable */
+#define  PCI_EXP_SLTCTL_HPIE	0x0020	/* Hot-Plug Interrupt Enable */
+#define  PCI_EXP_SLTCTL_AIC	0x00c0	/* Attention Indicator Control */
+#define  PCI_EXP_SLTCTL_PIC	0x0300	/* Power Indicator Control */
+#define  PCI_EXP_SLTCTL_PCC	0x0400	/* Power Controller Control */
+#define  PCI_EXP_SLTCTL_EIC	0x0800	/* Electromechanical Interlock Control */
+#define  PCI_EXP_SLTCTL_DLLSCE	0x1000	/* Data Link Layer State Changed Enable */
+#define PCI_EXP_SLTSTA		26	/* Slot Status */
+#define  PCI_EXP_SLTSTA_ABP	0x0001	/* Attention Button Pressed */
+#define  PCI_EXP_SLTSTA_PFD	0x0002	/* Power Fault Detected */
+#define  PCI_EXP_SLTSTA_MRLSC	0x0004	/* MRL Sensor Changed */
+#define  PCI_EXP_SLTSTA_PDC	0x0008	/* Presence Detect Changed */
+#define  PCI_EXP_SLTSTA_CC	0x0010	/* Command Completed */
+#define  PCI_EXP_SLTSTA_MRLSS	0x0020	/* MRL Sensor State */
+#define  PCI_EXP_SLTSTA_PDS	0x0040	/* Presence Detect State */
+#define  PCI_EXP_SLTSTA_EIS	0x0080	/* Electromechanical Interlock Status */
+#define  PCI_EXP_SLTSTA_DLLSC	0x0100	/* Data Link Layer State Changed */
+#define PCI_EXP_RTCTL		28	/* Root Control */
+#define  PCI_EXP_RTCTL_SECEE	0x01	/* System Error on Correctable Error */
+#define  PCI_EXP_RTCTL_SENFEE	0x02	/* System Error on Non-Fatal Error */
+#define  PCI_EXP_RTCTL_SEFEE	0x04	/* System Error on Fatal Error */
+#define  PCI_EXP_RTCTL_PMEIE	0x08	/* PME Interrupt Enable */
+#define  PCI_EXP_RTCTL_CRSSVE	0x10	/* CRS Software Visibility Enable */
+#define PCI_EXP_RTCAP		30	/* Root Capabilities */
+#define PCI_EXP_RTSTA		32	/* Root Status */
+#define PCI_EXP_DEVCAP2		36	/* Device Capabilities 2 */
+#define  PCI_EXP_DEVCAP2_ARI	0x20	/* Alternative Routing-ID */
+#define PCI_EXP_DEVCTL2		40	/* Device Control 2 */
+#define  PCI_EXP_DEVCTL2_ARI	0x20	/* Alternative Routing-ID */
+#define PCI_EXP_LNKCTL2		48	/* Link Control 2 */
+#define PCI_EXP_SLTCTL2		56	/* Slot Control 2 */
+
+/* Extended Capabilities (PCI-X 2.0 and Express) */
+#define PCI_EXT_CAP_ID(header)		(header & 0x0000ffff)
+#define PCI_EXT_CAP_VER(header)		((header >> 16) & 0xf)
+#define PCI_EXT_CAP_NEXT(header)	((header >> 20) & 0xffc)
+
+#define PCI_EXT_CAP_ID_ERR	1
+#define PCI_EXT_CAP_ID_VC	2
+#define PCI_EXT_CAP_ID_DSN	3
+#define PCI_EXT_CAP_ID_PWR	4
+#define PCI_EXT_CAP_ID_ARI	14
+#define PCI_EXT_CAP_ID_ATS	15
+#define PCI_EXT_CAP_ID_SRIOV	16
+
+/* Advanced Error Reporting */
+#define PCI_ERR_UNCOR_STATUS	4	/* Uncorrectable Error Status */
+#define  PCI_ERR_UNC_TRAIN	0x00000001	/* Training */
+#define  PCI_ERR_UNC_DLP	0x00000010	/* Data Link Protocol */
+#define  PCI_ERR_UNC_POISON_TLP	0x00001000	/* Poisoned TLP */
+#define  PCI_ERR_UNC_FCP	0x00002000	/* Flow Control Protocol */
+#define  PCI_ERR_UNC_COMP_TIME	0x00004000	/* Completion Timeout */
+#define  PCI_ERR_UNC_COMP_ABORT	0x00008000	/* Completer Abort */
+#define  PCI_ERR_UNC_UNX_COMP	0x00010000	/* Unexpected Completion */
+#define  PCI_ERR_UNC_RX_OVER	0x00020000	/* Receiver Overflow */
+#define  PCI_ERR_UNC_MALF_TLP	0x00040000	/* Malformed TLP */
+#define  PCI_ERR_UNC_ECRC	0x00080000	/* ECRC Error Status */
+#define  PCI_ERR_UNC_UNSUP	0x00100000	/* Unsupported Request */
+#define PCI_ERR_UNCOR_MASK	8	/* Uncorrectable Error Mask */
+	/* Same bits as above */
+#define PCI_ERR_UNCOR_SEVER	12	/* Uncorrectable Error Severity */
+	/* Same bits as above */
+#define PCI_ERR_COR_STATUS	16	/* Correctable Error Status */
+#define  PCI_ERR_COR_RCVR	0x00000001	/* Receiver Error Status */
+#define  PCI_ERR_COR_BAD_TLP	0x00000040	/* Bad TLP Status */
+#define  PCI_ERR_COR_BAD_DLLP	0x00000080	/* Bad DLLP Status */
+#define  PCI_ERR_COR_REP_ROLL	0x00000100	/* REPLAY_NUM Rollover */
+#define  PCI_ERR_COR_REP_TIMER	0x00001000	/* Replay Timer Timeout */
+#define PCI_ERR_COR_MASK	20	/* Correctable Error Mask */
+	/* Same bits as above */
+#define PCI_ERR_CAP		24	/* Advanced Error Capabilities */
+#define  PCI_ERR_CAP_FEP(x)	((x) & 31)	/* First Error Pointer */
+#define  PCI_ERR_CAP_ECRC_GENC	0x00000020	/* ECRC Generation Capable */
+#define  PCI_ERR_CAP_ECRC_GENE	0x00000040	/* ECRC Generation Enable */
+#define  PCI_ERR_CAP_ECRC_CHKC	0x00000080	/* ECRC Check Capable */
+#define  PCI_ERR_CAP_ECRC_CHKE	0x00000100	/* ECRC Check Enable */
+#define PCI_ERR_HEADER_LOG	28	/* Header Log Register (16 bytes) */
+#define PCI_ERR_ROOT_COMMAND	44	/* Root Error Command */
+/* Correctable Err Reporting Enable */
+#define PCI_ERR_ROOT_CMD_COR_EN		0x00000001
+/* Non-fatal Err Reporting Enable */
+#define PCI_ERR_ROOT_CMD_NONFATAL_EN	0x00000002
+/* Fatal Err Reporting Enable */
+#define PCI_ERR_ROOT_CMD_FATAL_EN	0x00000004
+#define PCI_ERR_ROOT_STATUS	48
+#define PCI_ERR_ROOT_COR_RCV		0x00000001	/* ERR_COR Received */
+/* Multi ERR_COR Received */
+#define PCI_ERR_ROOT_MULTI_COR_RCV	0x00000002
+/* ERR_FATAL/NONFATAL Recevied */
+#define PCI_ERR_ROOT_UNCOR_RCV		0x00000004
+/* Multi ERR_FATAL/NONFATAL Recevied */
+#define PCI_ERR_ROOT_MULTI_UNCOR_RCV	0x00000008
+#define PCI_ERR_ROOT_FIRST_FATAL	0x00000010	/* First Fatal */
+#define PCI_ERR_ROOT_NONFATAL_RCV	0x00000020	/* Non-Fatal Received */
+#define PCI_ERR_ROOT_FATAL_RCV		0x00000040	/* Fatal Received */
+#define PCI_ERR_ROOT_COR_SRC	52
+#define PCI_ERR_ROOT_SRC	54
+
+/* Virtual Channel */
+#define PCI_VC_PORT_REG1	4
+#define PCI_VC_PORT_REG2	8
+#define PCI_VC_PORT_CTRL	12
+#define PCI_VC_PORT_STATUS	14
+#define PCI_VC_RES_CAP		16
+#define PCI_VC_RES_CTRL		20
+#define PCI_VC_RES_STATUS	26
+
+/* Power Budgeting */
+#define PCI_PWR_DSR		4	/* Data Select Register */
+#define PCI_PWR_DATA		8	/* Data Register */
+#define  PCI_PWR_DATA_BASE(x)	((x) & 0xff)	    /* Base Power */
+#define  PCI_PWR_DATA_SCALE(x)	(((x) >> 8) & 3)    /* Data Scale */
+#define  PCI_PWR_DATA_PM_SUB(x)	(((x) >> 10) & 7)   /* PM Sub State */
+#define  PCI_PWR_DATA_PM_STATE(x) (((x) >> 13) & 3) /* PM State */
+#define  PCI_PWR_DATA_TYPE(x)	(((x) >> 15) & 7)   /* Type */
+#define  PCI_PWR_DATA_RAIL(x)	(((x) >> 18) & 7)   /* Power Rail */
+#define PCI_PWR_CAP		12	/* Capability */
+#define  PCI_PWR_CAP_BUDGET(x)	((x) & 1)	/* Included in system budget */
+
+/*
+ * Hypertransport sub capability types
+ *
+ * Unfortunately there are both 3 bit and 5 bit capability types defined
+ * in the HT spec, catering for that is a little messy. You probably don't
+ * want to use these directly, just use pci_find_ht_capability() and it
+ * will do the right thing for you.
+ */
+#define HT_3BIT_CAP_MASK	0xE0
+#define HT_CAPTYPE_SLAVE	0x00	/* Slave/Primary link configuration */
+#define HT_CAPTYPE_HOST		0x20	/* Host/Secondary link configuration */
+
+#define HT_5BIT_CAP_MASK	0xF8
+#define HT_CAPTYPE_IRQ		0x80	/* IRQ Configuration */
+#define HT_CAPTYPE_REMAPPING_40	0xA0	/* 40 bit address remapping */
+#define HT_CAPTYPE_REMAPPING_64 0xA2	/* 64 bit address remapping */
+#define HT_CAPTYPE_UNITID_CLUMP	0x90	/* Unit ID clumping */
+#define HT_CAPTYPE_EXTCONF	0x98	/* Extended Configuration Space Access */
+#define HT_CAPTYPE_MSI_MAPPING	0xA8	/* MSI Mapping Capability */
+#define  HT_MSI_FLAGS		0x02		/* Offset to flags */
+#define  HT_MSI_FLAGS_ENABLE	0x1		/* Mapping enable */
+#define  HT_MSI_FLAGS_FIXED	0x2		/* Fixed mapping only */
+#define  HT_MSI_FIXED_ADDR	0x00000000FEE00000ULL	/* Fixed addr */
+#define  HT_MSI_ADDR_LO		0x04		/* Offset to low addr bits */
+#define  HT_MSI_ADDR_LO_MASK	0xFFF00000	/* Low address bit mask */
+#define  HT_MSI_ADDR_HI		0x08		/* Offset to high addr bits */
+#define HT_CAPTYPE_DIRECT_ROUTE	0xB0	/* Direct routing configuration */
+#define HT_CAPTYPE_VCSET	0xB8	/* Virtual Channel configuration */
+#define HT_CAPTYPE_ERROR_RETRY	0xC0	/* Retry on error configuration */
+#define HT_CAPTYPE_GEN3		0xD0	/* Generation 3 hypertransport configuration */
+#define HT_CAPTYPE_PM		0xE0	/* Hypertransport powermanagement configuration */
+
+/* Alternative Routing-ID Interpretation */
+#define PCI_ARI_CAP		0x04	/* ARI Capability Register */
+#define  PCI_ARI_CAP_MFVC	0x0001	/* MFVC Function Groups Capability */
+#define  PCI_ARI_CAP_ACS	0x0002	/* ACS Function Groups Capability */
+#define  PCI_ARI_CAP_NFN(x)	(((x) >> 8) & 0xff) /* Next Function Number */
+#define PCI_ARI_CTRL		0x06	/* ARI Control Register */
+#define  PCI_ARI_CTRL_MFVC	0x0001	/* MFVC Function Groups Enable */
+#define  PCI_ARI_CTRL_ACS	0x0002	/* ACS Function Groups Enable */
+#define  PCI_ARI_CTRL_FG(x)	(((x) >> 4) & 7) /* Function Group */
+
+/* Address Translation Service */
+#define PCI_ATS_CAP		0x04	/* ATS Capability Register */
+#define  PCI_ATS_CAP_QDEP(x)	((x) & 0x1f)	/* Invalidate Queue Depth */
+#define  PCI_ATS_MAX_QDEP	32	/* Max Invalidate Queue Depth */
+#define PCI_ATS_CTRL		0x06	/* ATS Control Register */
+#define  PCI_ATS_CTRL_ENABLE	0x8000	/* ATS Enable */
+#define  PCI_ATS_CTRL_STU(x)	((x) & 0x1f)	/* Smallest Translation Unit */
+#define  PCI_ATS_MIN_STU	12	/* shift of minimum STU block */
+
+/* Single Root I/O Virtualization */
+#define PCI_SRIOV_CAP		0x04	/* SR-IOV Capabilities */
+#define  PCI_SRIOV_CAP_VFM	0x01	/* VF Migration Capable */
+#define  PCI_SRIOV_CAP_INTR(x)	((x) >> 21) /* Interrupt Message Number */
+#define PCI_SRIOV_CTRL		0x08	/* SR-IOV Control */
+#define  PCI_SRIOV_CTRL_VFE	0x01	/* VF Enable */
+#define  PCI_SRIOV_CTRL_VFM	0x02	/* VF Migration Enable */
+#define  PCI_SRIOV_CTRL_INTR	0x04	/* VF Migration Interrupt Enable */
+#define  PCI_SRIOV_CTRL_MSE	0x08	/* VF Memory Space Enable */
+#define  PCI_SRIOV_CTRL_ARI	0x10	/* ARI Capable Hierarchy */
+#define PCI_SRIOV_STATUS	0x0a	/* SR-IOV Status */
+#define  PCI_SRIOV_STATUS_VFM	0x01	/* VF Migration Status */
+#define PCI_SRIOV_INITIAL_VF	0x0c	/* Initial VFs */
+#define PCI_SRIOV_TOTAL_VF	0x0e	/* Total VFs */
+#define PCI_SRIOV_NUM_VF	0x10	/* Number of VFs */
+#define PCI_SRIOV_FUNC_LINK	0x12	/* Function Dependency Link */
+#define PCI_SRIOV_VF_OFFSET	0x14	/* First VF Offset */
+#define PCI_SRIOV_VF_STRIDE	0x16	/* Following VF Stride */
+#define PCI_SRIOV_VF_DID	0x1a	/* VF Device ID */
+#define PCI_SRIOV_SUP_PGSIZE	0x1c	/* Supported Page Sizes */
+#define PCI_SRIOV_SYS_PGSIZE	0x20	/* System Page Size */
+#define PCI_SRIOV_BAR		0x24	/* VF BAR0 */
+#define  PCI_SRIOV_NUM_BARS	6	/* Number of VF BARs */
+#define PCI_SRIOV_VFM		0x3c	/* VF Migration State Array Offset*/
+#define  PCI_SRIOV_VFM_BIR(x)	((x) & 7)	/* State BIR */
+#define  PCI_SRIOV_VFM_OFFSET(x) ((x) & ~7)	/* State Offset */
+#define  PCI_SRIOV_VFM_UA	0x0	/* Inactive.Unavailable */
+#define  PCI_SRIOV_VFM_MI	0x1	/* Dormant.MigrateIn */
+#define  PCI_SRIOV_VFM_MO	0x2	/* Active.MigrateOut */
+#define  PCI_SRIOV_VFM_AV	0x3	/* Active.Available */
+
+#endif /* LINUX_PCI_REGS_H */
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 04/10] pci: use pci_regs.h

[Isaku Yamahata]

include pci_regs.h and remove duplicated defines.
And remove unused PCI_REVISION and PCI_SUBDEVICE_ID.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
---
 hw/pci.h |   77 ++-----------------------------------------------------------
 1 files changed, 3 insertions(+), 74 deletions(-)

diff --git a/hw/pci.h b/hw/pci.h
index 3be7a99..b5e7abb 100644
--- a/hw/pci.h
+++ b/hw/pci.h
@@ -94,81 +94,10 @@ typedef struct PCIIORegion {
 #define PCI_ROM_SLOT 6
 #define PCI_NUM_REGIONS 7
 
-/* Declarations from linux/pci_regs.h */
-#define PCI_VENDOR_ID		0x00	/* 16 bits */
-#define PCI_DEVICE_ID		0x02	/* 16 bits */
-#define PCI_COMMAND		0x04	/* 16 bits */
-#define  PCI_COMMAND_IO		0x1	/* Enable response in I/O space */
-#define  PCI_COMMAND_MEMORY	0x2	/* Enable response in Memory space */
-#define  PCI_COMMAND_MASTER	0x4	/* Enable bus master */
-#define  PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */
-#define PCI_STATUS              0x06    /* 16 bits */
-#define  PCI_STATUS_INTERRUPT   0x08
-#define PCI_REVISION_ID         0x08    /* 8 bits  */
-#define PCI_CLASS_PROG		0x09	/* Reg. Level Programming Interface */
-#define PCI_CLASS_DEVICE        0x0a    /* Device class */
-#define PCI_CACHE_LINE_SIZE	0x0c	/* 8 bits */
-#define PCI_LATENCY_TIMER	0x0d	/* 8 bits */
-#define PCI_HEADER_TYPE         0x0e    /* 8 bits */
-#define  PCI_HEADER_TYPE_NORMAL		0
-#define  PCI_HEADER_TYPE_BRIDGE		1
-#define  PCI_HEADER_TYPE_CARDBUS	2
+#include "pci_regs.h"
+
+/* PCI HEADER_TYPE */
 #define  PCI_HEADER_TYPE_MULTI_FUNCTION 0x80
-#define PCI_BASE_ADDRESS_0	0x10	/* 32 bits */
-#define  PCI_BASE_ADDRESS_SPACE_IO	0x01
-#define  PCI_BASE_ADDRESS_SPACE_MEMORY	0x00
-#define  PCI_BASE_ADDRESS_MEM_TYPE_64	0x04	/* 64 bit address */
-#define  PCI_BASE_ADDRESS_MEM_PREFETCH	0x08	/* prefetchable? */
-#define PCI_PRIMARY_BUS		0x18	/* Primary bus number */
-#define PCI_SECONDARY_BUS	0x19	/* Secondary bus number */
-#define PCI_SUBORDINATE_BUS	0x1a	/* Highest bus number behind the bridge */
-#define PCI_IO_BASE             0x1c    /* I/O range behind the bridge */
-#define PCI_IO_LIMIT            0x1d
-#define  PCI_IO_RANGE_TYPE_32	0x01
-#define  PCI_IO_RANGE_MASK      (~0x0fUL)
-#define PCI_SEC_STATUS		0x1e	/* Secondary status register, only bit 14 used */
-#define PCI_MEMORY_BASE         0x20    /* Memory range behind */
-#define PCI_MEMORY_LIMIT        0x22
-#define  PCI_MEMORY_RANGE_MASK  (~0x0fUL)
-#define PCI_PREF_MEMORY_BASE    0x24    /* Prefetchable memory range behind */
-#define PCI_PREF_MEMORY_LIMIT   0x26
-#define  PCI_PREF_RANGE_MASK    (~0x0fUL)
-#define  PCI_PREF_RANGE_TYPE_64 0x01
-#define PCI_PREF_BASE_UPPER32   0x28    /* Upper half of prefetchable memory range */
-#define PCI_PREF_LIMIT_UPPER32	0x2c
-#define PCI_SUBSYSTEM_VENDOR_ID 0x2c    /* 16 bits */
-#define PCI_SUBSYSTEM_ID        0x2e    /* 16 bits */
-#define PCI_ROM_ADDRESS		0x30	/* Bits 31..11 are address, 10..1 reserved */
-#define  PCI_ROM_ADDRESS_ENABLE	0x01
-#define PCI_IO_BASE_UPPER16     0x30    /* Upper half of I/O addresses */
-#define PCI_IO_LIMIT_UPPER16    0x32
-#define PCI_CAPABILITY_LIST	0x34	/* Offset of first capability list entry */
-#define PCI_ROM_ADDRESS1	0x38	/* Same as PCI_ROM_ADDRESS, but for htype 1 */
-#define PCI_INTERRUPT_LINE	0x3c	/* 8 bits */
-#define PCI_INTERRUPT_PIN	0x3d	/* 8 bits */
-#define PCI_MIN_GNT		0x3e	/* 8 bits */
-#define PCI_BRIDGE_CONTROL      0x3e
-#define PCI_MAX_LAT		0x3f	/* 8 bits */
-
-/* Capability lists */
-#define PCI_CAP_LIST_ID		0	/* Capability ID */
-#define PCI_CAP_LIST_NEXT	1	/* Next capability in the list */
-
-#define PCI_REVISION            0x08    /* obsolete, use PCI_REVISION_ID */
-#define PCI_SUBSYSTEM_VENDOR_ID 0x2c
-#define PCI_SUBDEVICE_ID        0x2e    /* obsolete, use PCI_SUBSYSTEM_ID */
-
-/* Bits in the PCI Status Register (PCI 2.3 spec) */
-#define PCI_STATUS_RESERVED1	0x007
-#define PCI_STATUS_INT_STATUS	0x008
-#define PCI_STATUS_CAP_LIST	0x010
-#define PCI_STATUS_66MHZ	0x020
-#define PCI_STATUS_RESERVED2	0x040
-#define PCI_STATUS_FAST_BACK	0x080
-#define PCI_STATUS_DEVSEL_MEDIUM 0x200
-#define PCI_STATUS_DEVSEL_SLOW	0x400
-#define  PCI_STATUS_SIG_TARGET_ABORT	0x800 /* Set on target abort */
-#define  PCI_STATUS_REC_MASTER_ABORT	0x2000 /* Set on master abort */
 
 #define PCI_STATUS_RESERVED_MASK_LO (PCI_STATUS_RESERVED1 | \
                 PCI_STATUS_INT_STATUS | PCI_STATUS_CAPABILITIES | \
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 05/10] gt64xxx: remove gt64120_{read, write}_config().

[Isaku Yamahata]

They call only pci_default_{read, write}_config().
So they aren't necessary.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
---
 hw/gt64xxx.c |   13 +------------
 1 files changed, 1 insertions(+), 12 deletions(-)

diff --git a/hw/gt64xxx.c b/hw/gt64xxx.c
index fb7f5bd..c8034e2 100644
--- a/hw/gt64xxx.c
+++ b/hw/gt64xxx.c
@@ -1082,17 +1082,6 @@ static void gt64120_reset(void *opaque)
     gt64120_pci_mapping(s);
 }
 
-static uint32_t gt64120_read_config(PCIDevice *d, uint32_t address, int len)
-{
-    return pci_default_read_config(d, address, len);
-}
-
-static void gt64120_write_config(PCIDevice *d, uint32_t address, uint32_t val,
-                                 int len)
-{
-    pci_default_write_config(d, address, val, len);
-}
-
 static void gt64120_save(QEMUFile* f, void *opaque)
 {
     PCIDevice *d = opaque;
@@ -1125,7 +1114,7 @@ PCIBus *pci_gt64120_init(qemu_irq *pic)
                                    pic, 144, 4);
     s->ISD_handle = cpu_register_io_memory(gt64120_read, gt64120_write, s);
     d = pci_register_device(s->pci->bus, "GT64120 PCI Bus", sizeof(PCIDevice),
-                            0, gt64120_read_config, gt64120_write_config);
+                            0, NULL, NULL);
 
     /* FIXME: Malta specific hw assumptions ahead */
 
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 06/10] acpi: use range helper function.

[Isaku Yamahata]

use range helper function in pm_write_config().

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
---
 hw/acpi.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/hw/acpi.c b/hw/acpi.c
index 9a69e7d..ad72297 100644
--- a/hw/acpi.c
+++ b/hw/acpi.c
@@ -437,7 +437,7 @@ static void pm_write_config(PCIDevice *d,
                             uint32_t address, uint32_t val, int len)
 {
     pci_default_write_config(d, address, val, len);
-    if (address == 0x80)
+    if (range_covers_byte(address, len, 0x80))
         pm_io_space_update((PIIX4PMState *)d);
 }
 
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 07/10] msix: use range helper function.

[Isaku Yamahata]

use range helper function in msix_write_config().

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
---
 hw/msix.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/hw/msix.c b/hw/msix.c
index 0baedef..2ca0900 100644
--- a/hw/msix.c
+++ b/hw/msix.c
@@ -175,7 +175,7 @@ void msix_write_config(PCIDevice *dev, uint32_t addr,
     unsigned enable_pos = dev->msix_cap + MSIX_CONTROL_OFFSET;
     int vector;
 
-    if (addr + len <= enable_pos || addr > enable_pos) {
+    if (!range_covers_byte(addr, len, enable_pos)) {
         return;
     }
 
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 08/10] piix_pci: define symbolic value for PAM0, PAM6 and SMRAM.

[Isaku Yamahata]

Define symbolic value in i440fx configuration space
for 0x59, 0x5f and 0x7f and use them.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
---
 hw/piix_pci.c |   17 ++++++++++++-----
 1 files changed, 12 insertions(+), 5 deletions(-)

diff --git a/hw/piix_pci.c b/hw/piix_pci.c
index 1b67475..0dae6f9 100644
--- a/hw/piix_pci.c
+++ b/hw/piix_pci.c
@@ -44,6 +44,11 @@ struct PCII440FXState {
     PIIX3State *piix3;
 };
 
+
+#define I440FX_PAM      0x59
+#define I440FX_PAM_SIZE 7
+#define I440FX_SMRAM    0x72
+
 static void piix3_set_irq(void *opaque, int irq_num, int level);
 
 /* return the global irq number corresponding to a given device irq
@@ -88,12 +93,12 @@ static void i440fx_update_memory_mappings(PCII440FXState *d)
     int i, r;
     uint32_t smram, addr;
 
-    update_pam(d, 0xf0000, 0x100000, (d->dev.config[0x59] >> 4) & 3);
+    update_pam(d, 0xf0000, 0x100000, (d->dev.config[I440FX_PAM] >> 4) & 3);
     for(i = 0; i < 12; i++) {
-        r = (d->dev.config[(i >> 1) + 0x5a] >> ((i & 1) * 4)) & 3;
+        r = (d->dev.config[(i >> 1) + (I440FX_PAM + 1)] >> ((i & 1) * 4)) & 3;
         update_pam(d, 0xc0000 + 0x4000 * i, 0xc0000 + 0x4000 * (i + 1), r);
     }
-    smram = d->dev.config[0x72];
+    smram = d->dev.config[I440FX_SMRAM];
     if ((d->smm_enabled && (smram & 0x08)) || (smram & 0x40)) {
         cpu_register_physical_memory(0xa0000, 0x20000, 0xa0000);
     } else {
@@ -132,7 +137,9 @@ static void i440fx_write_config(PCIDevice *dev,
 
     /* XXX: implement SMRAM.D_LOCK */
     pci_default_write_config(dev, address, val, len);
-    if ((address >= 0x59 && address <= 0x5f) || address == 0x72)
+    if ((address >= I440FX_PAM &&
+         address <= I440FX_PAM + I440FX_PAM_SIZE - 1) ||
+        address == I440FX_SMRAM)
         i440fx_update_memory_mappings(d);
 }
 
@@ -196,7 +203,7 @@ static int i440fx_initfn(PCIDevice *dev)
     pci_config_set_class(d->dev.config, PCI_CLASS_BRIDGE_HOST);
     d->dev.config[PCI_HEADER_TYPE] = PCI_HEADER_TYPE_NORMAL; // header_type
 
-    d->dev.config[0x72] = 0x02; /* SMRAM */
+    d->dev.config[I440FX_SMRAM] = 0x02;
 
     return 0;
 }
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 09/10] piix_pci: use range helper function

[Isaku Yamahata]

use range helper function in i440fx_write_config().

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
---
 hw/piix_pci.c |    6 +++---
 1 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/hw/piix_pci.c b/hw/piix_pci.c
index 0dae6f9..384d31c 100644
--- a/hw/piix_pci.c
+++ b/hw/piix_pci.c
@@ -137,10 +137,10 @@ static void i440fx_write_config(PCIDevice *dev,
 
     /* XXX: implement SMRAM.D_LOCK */
     pci_default_write_config(dev, address, val, len);
-    if ((address >= I440FX_PAM &&
-         address <= I440FX_PAM + I440FX_PAM_SIZE - 1) ||
-        address == I440FX_SMRAM)
+    if (ranges_overlap(address, len, I440FX_PAM, I440FX_PAM_SIZE) ||
+        range_covers_byte(address, len, I440FX_SMRAM)) {
         i440fx_update_memory_mappings(d);
+    }
 }
 
 static int i440fx_load_old(QEMUFile* f, void *opaque, int version_id)
-- 
1.6.5.4

[Qemu-devel] [PATCH V2 10/10] piix_pci: add link to i440fx data sheet.

[Isaku Yamahata]

add link to i440fx data sheet.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
---
 hw/piix_pci.c |    5 +++++
 1 files changed, 5 insertions(+), 0 deletions(-)

diff --git a/hw/piix_pci.c b/hw/piix_pci.c
index 384d31c..cd12212 100644
--- a/hw/piix_pci.c
+++ b/hw/piix_pci.c
@@ -29,6 +29,11 @@
 #include "isa.h"
 #include "sysbus.h"
 
+/*
+ * I440FX chipset data sheet.
+ * http://download.intel.com/design/chipsets/datashts/29054901.pdf
+ */
+
 typedef PCIHostState I440FXState;
 
 typedef struct PIIX3State {
-- 
1.6.5.4

[Qemu-devel] Re: [PATCH V2 00/10] various pci clean ups.

[Michael S. Tsirkin]

On Tue, Dec 15, 2009 at 08:25:57PM +0900, Isaku Yamahata wrote:
> This patch series is for various somewhat atrandom clean up.
> 
> - the patch "piix_pci: define symbolic value for PAM0, PAM6 and SMRAM."
>   doesn't cause binary difference.
>   I checked the piix_pci.o binary doesn't changed with the patch applied
>   or not by diffing results of disassembling object files.
> 
> - rebased to MST's git tree
> git://git.kernel.org/pub/scm/linux/kernel/git/mst/qemu.git pci.
> Anyway the only patch "pci: use pci_regs.h" 4 patch conflicts.
> So I expect all but the patch "pci: use pci_regs.h" can applies to
> unstable tree. And it's trivial to resolve the conflict.
> 
> changes v1 -> v2:
> - dropped the patch "pci: clean up pci_bar_address()"
> - reordered
> - rebased to git://git.kernel.org/pub/scm/linux/kernel/git/mst/qemu.git pci
> - updated I440FX patch.
> - added link to I440FX link


Thanks!
Applied.

> Isaku Yamahata (10):
>   pci: remove PCIBus::config_reg.
>   pci: s/PCI_SUBVENDOR_ID/PCI_SUBSYSTEM_VENDOR_ID/g
>   pci: import Linux pci_regs.h
>   pci: use pci_regs.h
>   gt64xxx: remove gt64120_{read, write}_config().
>   acpi: use range helper function.
>   msix: use range helper function.
>   piix_pci: define symbolic value for PAM0, PAM6 and SMRAM.
>   piix_pci: use range helper function
>   piix_pci: add link to i440fx data sheet.
> 
>  hw/acpi.c     |    2 +-
>  hw/gt64xxx.c  |   13 +-
>  hw/msix.c     |    2 +-
>  hw/pci.c      |    3 +-
>  hw/pci.h      |   77 +-------
>  hw/pci_regs.h |  665 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>  hw/piix_pci.c |   22 ++-
>  7 files changed, 689 insertions(+), 95 deletions(-)
>  create mode 100644 hw/pci_regs.h