From: "Antonio Marcos López Alonso" <amlopezalonso@gmail.com>
To: linux-media@vger.kernel.org
Subject: How to make a Zaapa LR301AP DVB-T card work
Date: Sat, 19 Dec 2009 14:00:37 +0000 [thread overview]
Message-ID: <200912191400.37814.amlopezalonso@gmail.com> (raw)
Hi all,
I borrowed a Zaapa LR301AP DVB-T card from a friend to try to make it work in
Linux, so I kindly request your help. The card features one antenna input, one
IR input (remote and sensor wire being lost) and one AV input. Here follows
the system info:
On-board printed info:
************************
Main chip: Philips SAA 7134 HL
Other chips: TDA 10046A, TDA 8274, MDT 2005ES-G.
lspci -vnn
****************
00:0c.0 Multimedia controller [0480]: Philips Semiconductors SAA7134/SAA7135HL
Video Broadcast Decoder [1131:7134] (rev 01)
Subsystem: Device [4e42:0301]
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at dffffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [40] Power Management version 1
Kernel driver in use: saa7134
dmesg | grep saa
*******************
saa7130/34: v4l2 driver version 0.2.15 loaded
[ 8.854415] saa7134 0000:00:0c.0: PCI INT A -> Link[LNKB] -> GSI 11 (level,
low) -> IRQ 11
[ 8.854423] saa7134[0]: found at 0000:00:0c.0, rev: 1, irq: 11, latency:
64, mmio: 0xdffffc00
[ 8.854430] saa7134[0]: subsystem: 4e42:0301, board: UNKNOWN/GENERIC
[card=0,autodetected]
[ 8.854453] saa7134[0]: board init: gpio is 10000
[ 8.854458] IRQ 11/saa7134[0]: IRQF_DISABLED is not guaranteed on shared
IRQs
[ 9.004012] saa7134[0]: i2c eeprom 00: 42 4e 01 03 54 20 1c 00 43 43 a9 1c
55 d2 b2 92
[ 9.004022] saa7134[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff
ff ff ff ff
[ 9.004030] saa7134[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 ff 01 e2
ff ff ff ff
[ 9.004038] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004045] saa7134[0]: i2c eeprom 40: ff 1b 00 c0 ff 10 01 00 ff ff ff ff
ff ff ff ff
[ 9.004052] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004059] saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004067] saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004074] saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004081] saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004089] saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004096] saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004103] saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004111] saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004118] saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004125] saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff
[ 9.004271] saa7134[0]: registered device video0 [v4l2]
[ 9.004299] saa7134[0]: registered device vbi0
[ 9.565411] saa7134 ALSA driver for DMA sound loaded
[ 9.565424] IRQ 11/saa7134[0]: IRQF_DISABLED is not guaranteed on shared
IRQs
[ 9.565451] saa7134[0]/alsa: saa7134[0] at 0xdffffc00 irq 11 registered as
card -1
[ 3368.737762] saa7134[0]/irq[10,4295734480]: r=0x20 s=0x00 PE
[ 3368.737770] saa7134[0]/irq: looping -- clearing PE (parity error!) enable
bit
************************************************************************************
No DVB-T button appears in Kaffeine, so the card is not being detected by the
app.
Thanks for any help
Antonio
next reply other threads:[~2009-12-19 14:00 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-12-19 14:00 Antonio Marcos López Alonso [this message]
2009-12-19 19:53 ` How to make a Zaapa LR301AP DVB-T card work hermann pitton
2009-12-20 13:13 ` Antonio Marcos López Alonso
2009-12-21 20:51 ` hermann pitton
2009-12-22 16:41 ` Antonio Marcos López Alonso
2009-12-23 1:50 ` hermann pitton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200912191400.37814.amlopezalonso@gmail.com \
--to=amlopezalonso@gmail.com \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.