From: Christoph Hellwig <hch@lst.de>
To: roland@redhat.com, oleg@redhat.com, akpm@linux-foundation.org,
gerg@uclinux.org
Cc: linux-kernel@vger.kernel.org, linux-arch@vger.kernel.org
Subject: [PATCH 7/14] m68knommu: use generic ptrace_resume code
Date: Tue, 2 Feb 2010 19:59:35 +0100 [thread overview]
Message-ID: <20100202185935.GG3630@lst.de> (raw)
In-Reply-To: <20100202185755.GA3630@lst.de>
Use the generic ptrace_resume code for PTRACE_SYSCALL, PTRACE_CONT,
PTRACE_KILL and PTRACE_SINGLESTEP. m68knommu already defines the
nessecary user_enable_single_step and user_disable_single_step functions
for this.
Also the TIF_SYSCALL_TRACE thread flag is now cleared on PTRACE_KILL
which it previously wasn't which is consistent with all architectures
using the modern ptrace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Index: linux-2.6/arch/m68knommu/kernel/ptrace.c
===================================================================
--- linux-2.6.orig/arch/m68knommu/kernel/ptrace.c 2010-02-02 11:00:49.987254269 +0100
+++ linux-2.6/arch/m68knommu/kernel/ptrace.c 2010-02-02 11:22:17.003259609 +0100
@@ -190,62 +190,6 @@ long arch_ptrace(struct task_struct *chi
}
break;
- case PTRACE_SYSCALL: /* continue and stop at next (return from) syscall */
- case PTRACE_CONT: { /* restart after signal. */
- long tmp;
-
- ret = -EIO;
- if (!valid_signal(data))
- break;
- if (request == PTRACE_SYSCALL)
- set_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
- else
- clear_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
- child->exit_code = data;
- /* make sure the single step bit is not set. */
- tmp = get_reg(child, PT_SR) & ~(TRACE_BITS << 16);
- put_reg(child, PT_SR, tmp);
- wake_up_process(child);
- ret = 0;
- break;
- }
-
- /*
- * make the child exit. Best I can do is send it a sigkill.
- * perhaps it should be put in the status that it wants to
- * exit.
- */
- case PTRACE_KILL: {
- long tmp;
-
- ret = 0;
- if (child->exit_state == EXIT_ZOMBIE) /* already dead */
- break;
- child->exit_code = SIGKILL;
- /* make sure the single step bit is not set. */
- tmp = get_reg(child, PT_SR) & ~(TRACE_BITS << 16);
- put_reg(child, PT_SR, tmp);
- wake_up_process(child);
- break;
- }
-
- case PTRACE_SINGLESTEP: { /* set the trap flag. */
- long tmp;
-
- ret = -EIO;
- if (!valid_signal(data))
- break;
- clear_tsk_thread_flag(child, TIF_SYSCALL_TRACE);
- tmp = get_reg(child, PT_SR) | (TRACE_BITS << 16);
- put_reg(child, PT_SR, tmp);
-
- child->exit_code = data;
- /* give it a chance to run. */
- wake_up_process(child);
- ret = 0;
- break;
- }
-
case PTRACE_GETREGS: { /* Get all gp regs from the child. */
int i;
unsigned long tmp;
next prev parent reply other threads:[~2010-02-02 18:59 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-02 18:57 [PATCH 1/14] move user_enable_single_step & co prototypes to linux/ptrace.h Christoph Hellwig
2010-02-02 18:58 ` [PATCH 2/14] alpha: use generic ptrace_resume code Christoph Hellwig
2010-02-03 4:35 ` Matt Turner
2010-02-02 18:58 ` [PATCH 3/14] arm: " Christoph Hellwig
2010-02-02 18:58 ` [PATCH 4/14] avr32: " Christoph Hellwig
2010-02-03 3:17 ` Haavard Skinnemoen
2010-02-03 8:36 ` Christoph Hellwig
2010-02-03 19:22 ` Oleg Nesterov
2010-02-03 19:28 ` Christoph Hellwig
2010-02-02 18:59 ` [PATCH 5/14] blackfin: " Christoph Hellwig
2010-02-02 20:29 ` Mike Frysinger
2010-02-03 19:36 ` Mike Frysinger
2010-02-03 19:42 ` Christoph Hellwig
2010-02-11 9:43 ` [PATCH 0/2] Blackfin: " Mike Frysinger
2010-02-11 9:43 ` [PATCH 1/2] Blackfin: initial tracehook support Mike Frysinger
2010-02-11 20:46 ` Roland McGrath
2010-02-11 23:54 ` Mike Frysinger
2010-02-12 3:24 ` Roland McGrath
2010-02-12 4:33 ` Mike Frysinger
2010-02-12 15:24 ` Oleg Nesterov
[not found] ` <8bd0f97a1002112033m5805d4eco3add4d5625e71e9-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-02-12 20:44 ` Roland McGrath
2010-02-12 20:44 ` Roland McGrath
2010-02-13 9:41 ` Mike Frysinger
2010-02-15 7:36 ` Mike Frysinger
2010-02-15 20:07 ` Roland McGrath
2010-02-11 9:43 ` [PATCH 2/2] Blackfin: use generic ptrace_resume code Mike Frysinger
2010-02-11 9:43 ` Mike Frysinger
2010-02-11 9:43 ` Mike Frysinger
2010-02-02 18:59 ` [PATCH 6/14] h8300: " Christoph Hellwig
2010-02-02 18:59 ` Christoph Hellwig [this message]
2010-02-03 6:54 ` [PATCH 7/14] m68knommu: " Greg Ungerer
2010-02-02 18:59 ` [PATCH 8/14] microblaze: " Christoph Hellwig
2010-02-03 11:00 ` Michal Simek
2010-02-02 18:59 ` [PATCH 9/14] mips: " Christoph Hellwig
2010-02-02 19:19 ` Ralf Baechle
2010-02-02 19:00 ` [PATCH 10/14] um: " Christoph Hellwig
2010-02-02 19:00 ` [PATCH 11/14] xtensa: " Christoph Hellwig
2010-02-02 19:00 ` [PATCH 12/14] cris arch-v10: " Christoph Hellwig
2010-02-02 19:00 ` [PATCH, RFC 13/14] cris arch-v32: " Christoph Hellwig
2010-02-02 19:00 ` [PATCH, RFC 14/14] m32r: " Christoph Hellwig
2010-02-03 8:42 ` [PATCH 1/14] move user_enable_single_step & co prototypes to linux/ptrace.h Mike Frysinger
2010-02-03 8:42 ` Mike Frysinger
2010-02-03 8:56 ` Christoph Hellwig
2010-02-08 10:50 ` David Howells
2010-02-08 19:51 ` Roland McGrath
2010-02-10 22:03 ` Christoph Hellwig
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100202185935.GG3630@lst.de \
--to=hch@lst.de \
--cc=akpm@linux-foundation.org \
--cc=gerg@uclinux.org \
--cc=linux-arch@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=oleg@redhat.com \
--cc=roland@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.