From: Ben Dooks <ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org>
To: Manjunatha GK <manjugk-l0cyMroinI0@public.gmane.org>
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org, "Kalliguddi,
Hema" <hemahk-l0cyMroinI0@public.gmane.org>,
Nishanth Menon <nm-l0cyMroinI0@public.gmane.org>,
Aaro Koskinen
<Aaro.Koskinen-xNZwKgViW5gAvxtiuMwx3w@public.gmane.org>
Subject: Re: [PATCH v4] OMAP2/3: I2C: Errata ID i207: Clear wrong RDR interrupt
Date: Tue, 20 Apr 2010 01:16:33 +0100 [thread overview]
Message-ID: <20100420001633.GM32401@fluff.org.uk> (raw)
In-Reply-To: <1271661262-10538-1-git-send-email-manjugk-l0cyMroinI0@public.gmane.org>
On Mon, Apr 19, 2010 at 12:44:22PM +0530, Manjunatha GK wrote:
> Under certain rare conditions, I2C_STAT[13].RDR bit may be set
> and the corresponding interrupt fire, even there is no data in
> the receive FIFO, or the I2C data transfer is still ongoing.
> These spurious RDR events must be ignored by the software.
>
> This patch handles and ignores RDR spurious interrupts.
>
> The below sequence is required in interrupt handler for
> handling this errata:
> 1. If RDR is set to 1, clear RDR
> 2. Read I2C status register and check for BusBusy bit. If BusBusy
> bit is set, skip remaining steps.
> 3. If BusBusy bit is not set, perform read operation on I2C status
> register.
> 4. If RDR is set, clear the same. Check RDR again and clear if it sets
> RDR bit again.
> 5. Perform I2C Data Read operation N number of times(where N is value
> read from the register BUFSTAT-RXSTAT bit fields).
>
> Note : This errata is applicable for OMAP2 and OMAP3 platforms only.
> It is not applicable for OMAP4.
If people can give me a yes/no before the end of play tomorrow (ie,
2300GMT) then I will get this applied to for-linus/i2c and send it
for -rc.
> Signed-off-by: Manjunatha GK <manjugk-l0cyMroinI0@public.gmane.org>
> Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> Cc: ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org
> Cc: Kalliguddi, Hema <hemahk-l0cyMroinI0@public.gmane.org>
> Cc: Nishanth Menon <nm-l0cyMroinI0@public.gmane.org>
> Cc: Aaro Koskinen <Aaro.Koskinen-xNZwKgViW5gAvxtiuMwx3w@public.gmane.org>
>
> ---
> drivers/i2c/busses/i2c-omap.c | 28 ++++++++++++++++++++++++++++
> 1 files changed, 28 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
> index f2019d2..8309eac 100644
> --- a/drivers/i2c/busses/i2c-omap.c
> +++ b/drivers/i2c/busses/i2c-omap.c
> @@ -796,6 +796,34 @@ complete:
> }
> if (stat & (OMAP_I2C_STAT_RRDY | OMAP_I2C_STAT_RDR)) {
> u8 num_bytes = 1;
> +
> + /*
> + * I2C Errata(Errata Nos. OMAP2: 1.67, OMAP3: 1.8)
> + * Not applicable for OMAP4.
> + * Under certain rare conditions, RDR could be set again
> + * when the bus is busy, then ignore the interrupt and
> + * clear the interrupt.
> + */
> + if ((stat & OMAP_I2C_STAT_RDR) && !cpu_is_omap44xx()) {
> + /* Step 1: If RDR is set, clear it */
> + omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RDR);
> +
> + /* Step 2: */
> + if(!(omap_i2c_read_reg(dev, OMAP_I2C_STAT_REG)
> + & OMAP_I2C_STAT_BB)) {
> + /* Step 3: */
> + if(omap_i2c_read_reg(dev,
> + OMAP_I2C_STAT_REG)
> + & OMAP_I2C_STAT_RDR) {
> + omap_i2c_ack_stat(dev,
> + OMAP_I2C_STAT_RDR);
> + dev_err(dev->dev,
> + "RDR when the bus is busy.\n");
> + continue;
> + }
> +
> + }
> + }
> if (dev->fifo_size) {
> if (stat & OMAP_I2C_STAT_RRDY)
> num_bytes = dev->fifo_size;
> --
> 1.6.0.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
> the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Ben (ben-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org, http://www.fluff.org/)
'a smiley only costs 4 bytes'
next prev parent reply other threads:[~2010-04-20 0:16 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-04-19 7:14 [PATCH v4] OMAP2/3: I2C: Errata ID i207: Clear wrong RDR interrupt Manjunatha GK
[not found] ` <1271661262-10538-1-git-send-email-manjugk-l0cyMroinI0@public.gmane.org>
2010-04-20 0:16 ` Ben Dooks [this message]
[not found] ` <20100420001633.GM32401-elnMNo+KYs3pIgCt6eIbzw@public.gmane.org>
2010-04-21 21:52 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100420001633.GM32401@fluff.org.uk \
--to=ben-linux-elnmno+kys3ytjvyw6ydsg@public.gmane.org \
--cc=Aaro.Koskinen-xNZwKgViW5gAvxtiuMwx3w@public.gmane.org \
--cc=hemahk-l0cyMroinI0@public.gmane.org \
--cc=linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=manjugk-l0cyMroinI0@public.gmane.org \
--cc=nm-l0cyMroinI0@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.