[PATCH 09/13] mxcmmc: add card detect through DAT3 possibility

[daniel@caiaq.de (Daniel Mack)]

On Wed, May 19, 2010 at 06:46:04PM +0200, Eric B?nard wrote:
> Signed-off-by: Eric B?nard <eric@eukrea.com>
> ---
>  arch/arm/plat-mxc/include/mach/mmc.h |    3 +++
>  drivers/mmc/host/mxcmmc.c            |   16 +++++++++++++---
>  2 files changed, 16 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm/plat-mxc/include/mach/mmc.h b/arch/arm/plat-mxc/include/mach/mmc.h
> index de2128d..29115f4 100644
> --- a/arch/arm/plat-mxc/include/mach/mmc.h
> +++ b/arch/arm/plat-mxc/include/mach/mmc.h
> @@ -31,6 +31,9 @@ struct imxmmc_platform_data {
>  
>  	/* adjust slot voltage */
>  	void (*setpower)(struct device *, unsigned int vdd);
> +
> +	/* enable card detect using DAT3 */
> +	int dat3_card_detect;
>  };
>  
>  #endif
> diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c
> index ec18e3b..74c87e0 100644
> --- a/drivers/mmc/host/mxcmmc.c
> +++ b/drivers/mmc/host/mxcmmc.c
> @@ -119,6 +119,7 @@ struct mxcmci_host {
>  	int			detect_irq;
>  	int			dma;
>  	int			do_dma;
> +	int			default_irq_mask;
>  	int			use_sdio;
>  	unsigned int		power_mode;
>  	struct imxmmc_platform_data *pdata;
> @@ -228,7 +229,7 @@ static int mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
>  static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd,
>  		unsigned int cmdat)
>  {
> -	u32 int_cntr;
> +	u32 int_cntr = host->default_irq_mask;
>  	unsigned long flags;
>  
>  	WARN_ON(host->cmd != NULL);
> @@ -275,7 +276,7 @@ static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd,
>  static void mxcmci_finish_request(struct mxcmci_host *host,
>  		struct mmc_request *req)
>  {
> -	u32 int_cntr = 0;
> +	u32 int_cntr = host->default_irq_mask;
>  	unsigned long flags;
>  
>  	spin_lock_irqsave(&host->lock, flags);
> @@ -585,6 +586,9 @@ static irqreturn_t mxcmci_irq(int irq, void *devid)
>  		  (stat & (STATUS_DATA_TRANS_DONE | STATUS_WRITE_OP_DONE)))
>  		mxcmci_data_done(host, stat);
>  #endif
> +	if (host->default_irq_mask &&
> +		  (stat & (STATUS_CARD_INSERTION | STATUS_CARD_REMOVAL)))
> +		mmc_detect_change(host->mmc, msecs_to_jiffies(200));
>  	return IRQ_HANDLED;
>  }
>  
> @@ -809,6 +813,12 @@ static int mxcmci_probe(struct platform_device *pdev)
>  	else
>  		mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
>  
> +	if (host->pdata && host->pdata->dat3_card_detect)

As 0 is a valid GPIO, so you should use gpio_is_valid() here, and update
all users' pdata to set dat3_card_detect = -1, so it will fail this
test.

Daniel