From: Anton Vorontsov <cbouatmailru@gmail.com>
To: Andrew Morton <akpm@linux-foundation.org>,
David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Mark Brown <broonie@opensource.wolfsonmicro.com>,
David Brownell <dbrownell@users.sourceforge.net>,
Alan Cox <alan@lxorguk.ukuu.org.uk>,
linux-kernel@vger.kernel.org
Subject: [PATCH v2] gpio: Add driver for Anton GPIO controllers
Date: Thu, 26 Aug 2010 21:26:02 +0400 [thread overview]
Message-ID: <20100826172602.GA20410@oksana.dev.rtsoft.ru> (raw)
In-Reply-To: <290252.99759.qm@web180316.mail.gq1.yahoo.com>
The Anton GPIO controllers are not so complex controllers that may
be found in various on-board FPGAs that are used to control board's
switches, LEDs, chip-selects, Ethernet/USB PHY power, etc.
Usually these controllers do not privide any means of pin setup
(in/out/open drain).
The driver provides:
- Support for 8/16/32/64 bits registers;
- Support for GPIO controllers with clear/set registers;
- Support for GPIO controllers with a single "data" register;
- Support for big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
---
In v2:
- Hopefully addressed David's comments regarding driver name;
- Now the driver fills gpio_chip.label.
drivers/gpio/Kconfig | 5 +
drivers/gpio/Makefile | 1 +
drivers/gpio/anton_gpio.c | 244 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 250 insertions(+), 0 deletions(-)
create mode 100644 drivers/gpio/anton_gpio.c
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index f623953..4658ca6 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -70,6 +70,11 @@ config GPIO_MAX730X
comment "Memory mapped GPIO expanders:"
+config GPIO_ANTON
+ tristate "Anton GPIO controllers support"
+ help
+ Say yes here to support Anton GPIO controllers.
+
config GPIO_IT8761E
tristate "IT8761E GPIO support"
depends on GPIOLIB
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index a69e060..a31ddae 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_GPIOLIB) += gpiolib.o
obj-$(CONFIG_GPIO_ADP5520) += adp5520-gpio.o
obj-$(CONFIG_GPIO_ADP5588) += adp5588-gpio.o
+obj-$(CONFIG_GPIO_ANTON) += anton_gpio.o
obj-$(CONFIG_GPIO_LANGWELL) += langwell_gpio.o
obj-$(CONFIG_GPIO_MAX730X) += max730x.o
obj-$(CONFIG_GPIO_MAX7300) += max7300.o
diff --git a/drivers/gpio/anton_gpio.c b/drivers/gpio/anton_gpio.c
new file mode 100644
index 0000000..d044385
--- /dev/null
+++ b/drivers/gpio/anton_gpio.c
@@ -0,0 +1,244 @@
+/*
+ * Anton GPIO driver
+ *
+ * Copyright 2008 MontaVista Software, Inc.
+ * Copyright 2008,2010 Anton Vorontsov <cbouatmailru@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/init.h>
+#include <linux/bug.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/compiler.h>
+#include <linux/types.h>
+#include <linux/log2.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/mod_devicetable.h>
+
+struct agpio_chip {
+ struct gpio_chip gc;
+ void __iomem *reg_dat;
+ void __iomem *reg_set;
+ void __iomem *reg_clr;
+ spinlock_t lock;
+
+ int bits;
+ int big_endian_bits;
+
+ /* shadowed data register to clear/set bits safely */
+ unsigned long data;
+};
+
+static struct agpio_chip *to_agpio_chip(struct gpio_chip *gc)
+{
+ return container_of(gc, struct agpio_chip, gc);
+}
+
+static unsigned long agpio_in(struct agpio_chip *agc)
+{
+ switch (agc->bits) {
+ case 8:
+ return __raw_readb(agc->reg_dat);
+ case 16:
+ return __raw_readw(agc->reg_dat);
+ case 32:
+ return __raw_readl(agc->reg_dat);
+#if BITS_PER_LONG >= 64
+ case 64:
+ return __raw_readq(agc->reg_dat);
+#endif
+ }
+ BUG();
+}
+
+static void agpio_out(struct agpio_chip *agc, void __iomem *reg,
+ unsigned long data)
+{
+ switch (agc->bits) {
+ case 8:
+ __raw_writeb(data, reg);
+ return;
+ case 16:
+ __raw_writew(data, reg);
+ return;
+ case 32:
+ __raw_writel(data, reg);
+ return;
+#if BITS_PER_LONG >= 64
+ case 64:
+ __raw_writeq(data, reg);
+ return;
+#endif
+ }
+ BUG();
+}
+
+static unsigned long agpio_pin2mask(struct agpio_chip *agc, unsigned int pin)
+{
+ if (agc->big_endian_bits)
+ return 1 << (agc->bits - 1 - pin);
+ else
+ return 1 << pin;
+}
+
+static int agpio_get(struct gpio_chip *gc, unsigned int gpio)
+{
+ struct agpio_chip *agc = to_agpio_chip(gc);
+
+ return agpio_in(agc) & agpio_pin2mask(agc, gpio);
+}
+
+static void agpio_set(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ struct agpio_chip *agc = to_agpio_chip(gc);
+ unsigned long mask = agpio_pin2mask(agc, gpio);
+ unsigned long flags;
+
+ if (agc->reg_set) {
+ if (val)
+ agpio_out(agc, agc->reg_set, mask);
+ else
+ agpio_out(agc, agc->reg_clr, mask);
+ return;
+ }
+
+ spin_lock_irqsave(&agc->lock, flags);
+
+ if (val)
+ agc->data |= mask;
+ else
+ agc->data &= ~mask;
+
+ agpio_out(agc, agc->reg_dat, agc->data);
+
+ spin_unlock_irqrestore(&agc->lock, flags);
+}
+
+static int agpio_dir_in(struct gpio_chip *gc, unsigned int gpio)
+{
+ return 0;
+}
+
+static int agpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val)
+{
+ agpio_set(gc, gpio, val);
+ return 0;
+}
+
+static int __devinit agpio_probe(struct platform_device *pdev)
+{
+ const struct platform_device_id *platid = platform_get_device_id(pdev);
+ struct device *dev = &pdev->dev;
+ struct agpio_chip *agc;
+ struct resource *res_dat;
+ struct resource *res_set;
+ struct resource *res_clr;
+ resource_size_t dat_sz;
+ int bits;
+
+ res_dat = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_dat)
+ return -EINVAL;
+
+ dat_sz = resource_size(res_dat);
+ if (!is_power_of_2(dat_sz))
+ return -EINVAL;
+
+ bits = dat_sz * 8;
+ if (bits > BITS_PER_LONG)
+ return -EINVAL;
+
+ agc = devm_kzalloc(dev, sizeof(*agc), GFP_KERNEL);
+ if (!agc)
+ return -ENOMEM;
+
+ agc->reg_dat = devm_ioremap(dev, res_dat->start, dat_sz);
+ if (!agc->reg_dat)
+ return -ENOMEM;
+
+ res_set = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ res_clr = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ if (res_set && res_clr) {
+ if (resource_size(res_set) != resource_size(res_clr) ||
+ resource_size(res_set) != dat_sz)
+ return -EINVAL;
+
+ agc->reg_set = devm_ioremap(dev, res_set->start, dat_sz);
+ agc->reg_clr = devm_ioremap(dev, res_clr->start, dat_sz);
+ if (!agc->reg_set || !agc->reg_clr)
+ return -ENOMEM;
+ } else if (res_set || res_clr) {
+ return -EINVAL;
+ }
+
+ spin_lock_init(&agc->lock);
+
+ agc->bits = bits;
+ agc->big_endian_bits = !strcmp(platid->name, "anton-gpio-be");
+ agc->data = agpio_in(agc);
+
+ agc->gc.ngpio = bits;
+ agc->gc.direction_input = agpio_dir_in;
+ agc->gc.direction_output = agpio_dir_out;
+ agc->gc.get = agpio_get;
+ agc->gc.set = agpio_set;
+ agc->gc.label = dev_name(dev);
+
+ if (dev->platform_data)
+ agc->gc.base = (unsigned long)dev->platform_data;
+ else
+ agc->gc.base = -1;
+
+ dev_set_drvdata(dev, agc);
+
+ return gpiochip_add(&agc->gc);
+}
+
+static int __devexit agpio_remove(struct platform_device *pdev)
+{
+ struct agpio_chip *agc = dev_get_drvdata(&pdev->dev);
+
+ return gpiochip_remove(&agc->gc);
+}
+
+static const struct platform_device_id agpio_id_table[] = {
+ { "anton-gpio", },
+ { "anton-gpio-be", },
+ {},
+};
+MODULE_DEVICE_TABLE(platform, agpio_id_table);
+
+static struct platform_driver agpio_driver = {
+ .driver = {
+ .name = "anton-gpio",
+ },
+ .id_table = agpio_id_table,
+ .probe = agpio_probe,
+ .remove = __devexit_p(agpio_remove),
+};
+
+static int __init agpio_init(void)
+{
+ return platform_driver_register(&agpio_driver);
+}
+module_init(agpio_init);
+
+static void __exit agpio_exit(void)
+{
+ platform_driver_unregister(&agpio_driver);
+}
+module_exit(agpio_exit);
+
+MODULE_DESCRIPTION("Driver for Anton GPIO controllers");
+MODULE_AUTHOR("Anton Vorontsov <cbouatmailru@gmail.com>");
+MODULE_LICENSE("GPL");
--
1.7.0.5
next prev parent reply other threads:[~2010-08-26 17:26 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-08-25 19:42 [PATCH] gpio: Add generic driver for simple memory mapped controllers Anton Vorontsov
[not found] ` <921098.64431.qm@web180306.mail.gq1.yahoo.com>
2010-08-26 5:17 ` Anton Vorontsov
2010-08-26 16:22 ` David Brownell
2010-08-26 16:48 ` Alan Cox
2010-08-26 17:34 ` David Brownell
2010-08-26 18:36 ` Mark Brown
2010-08-26 21:07 ` Alan Cox
2010-08-26 22:58 ` David Brownell
2010-08-27 0:15 ` Alan Cox
2010-08-26 17:26 ` Anton Vorontsov [this message]
2010-08-26 17:57 ` [PATCH v2] gpio: Add driver for Anton GPIO controllers David Brownell
2010-08-26 21:20 ` Anton Vorontsov
2010-08-26 22:48 ` David Brownell
2010-08-27 15:57 ` [PATCH v3] gpio: Add driver for basic memory-mapped " Anton Vorontsov
2010-08-28 19:08 ` David Brownell
2010-08-29 21:28 ` [PATCH v4] " Anton Vorontsov
2010-08-30 20:23 ` David Brownell
2010-08-31 17:58 ` [PATCH v5] " Anton Vorontsov
2010-08-31 18:21 ` Mark Brown
2010-08-31 20:32 ` David Brownell
2010-09-01 19:52 ` [PATCH v6] " Anton Vorontsov
2010-09-07 14:01 ` [PATCH v7] " Anton Vorontsov
2010-09-21 22:23 ` Anton Vorontsov
2010-09-24 21:45 ` Andrew Morton
2010-09-28 12:40 ` [PATCH v7-fix] gpio: Add driver for basic memory-mapped GPIO controllers (fix) Anton Vorontsov
2010-08-26 18:38 ` [PATCH] gpio: Add generic driver for simple memory mapped controllers Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100826172602.GA20410@oksana.dev.rtsoft.ru \
--to=cbouatmailru@gmail.com \
--cc=akpm@linux-foundation.org \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=david-b@pacbell.net \
--cc=dbrownell@users.sourceforge.net \
--cc=linux-kernel@vger.kernel.org \
--cc=sameo@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.