All of lore.kernel.org
 help / color / mirror / Atom feed
From: Arno Wagner <arno@wagner.name>
To: dm-crypt@saout.de
Subject: Re: [dm-crypt] Can't add a new key, "No key available with this	passphrase".
Date: Fri, 3 Sep 2010 20:16:46 +0200	[thread overview]
Message-ID: <20100903181646.GB11768@tansi.org> (raw)
In-Reply-To: <1283528215.4980.64.camel@shadowtek.localdomain>

It is relatively obvious that it asks for an existing passphrase
if you think about it. After all, if you could just add a new one,
that would be a way to break the encryption.

Arno


On Fri, Sep 03, 2010 at 11:36:55AM -0400, PsiStormYamato wrote:
> Ok, I see what the problem is. Thanks.
> 
> I think it would be good if the terminal response messages were a
> little more clear on exactly what's going on.
> 
> #1
> Apparently, using the option --key-file after specifying the device
> makes cryptsetup think that "--key-file" is the name of the file, which
> causes the error "No key available with this passphrase." I think it
> would be good to make an exception for that.
> 
> root@shadowtek-lucid:~# cryptsetup luksAddKey --key-slot 1 /dev/sda5
> --key-file /etc/cryptkeys/swap.key
> No key available with this passphrase.
> 
> #2
> When I tried it without the --key-file option, it appeared to me that
> the keyfile was again not being read correctly, and that I was being
> asked to
> manually enter a new passphrase.
> 
> root@shadowtek-lucid:~# cryptsetup luksAddKey --key-slot
> 1 /dev/sda5 /etc/cryptkeys/swap.key 
> Enter any passphrase: 
> No key available with this passphrase.
> 
> # 3
> When I tried to enter a new password manually, I was greeted with the
> same error, so I was under the impression that I was running into the
> same problem as before.
> 
> root@shadowtek-lucid:~# cryptsetup luksAddKey --key-slot 1 /dev/sda5
> Enter any passphrase: 
> No key available with this passphrase.
> 
> After trying #2 again, this time entering an existing passphrase, it
> worked. Thanks.
> 
> 
> On Fri, 2010-09-03 at 09:30 +0200, Arno Wagner wrote:
> 
> > I think you are using the wrong passphrase. You have to give
> > the passphrase of an existing used key-slot to add a new
> > one. Otherwise there would be a rather obvious attack ...
> > 
> > It should ask you for the passphrase for the new slot after that.
> > 
> > Arno
> > 
> > On Fri, Sep 03, 2010 at 12:24:46AM -0400, PsiStormYamato wrote:
> > > I'm trying to add a keyfile that I created to a new keyslot for my
> > > encrypted swap partition, but I keep getting the error "No key
> > > available with this passphrase". I've never done this before, so I
> > > might be missing something simple, but I can't get it to work by
> > > manually entering a passphase either.
> > > 
> > > Is there something else that has to be done to "enable" a keyslot
> > > before a key can be added to it? That's the only other thing that I can
> > > think of.
> > > 
> > > 
> > > # Tried with keyfile.
> > > root@ubuntu:~# cryptsetup luksAddKey --key-slot 1 /dev/sda5
> > > -d /media/Ubuntu_10_04/etc/cryptkeys/swap.key 
> > > 
> > > No key available with this passphrase.
> > > 
> > > 
> > > # Tried with manual passphrase.
> > > 
> > > root@subuntu:/etc/cryptkeys# cryptsetup luksAddKey --key-slot
> > > 1 /dev/sda5
> > > 
> > > Enter any passphrase: 
> > > No key available with this passphrase.
> > > 
> > > 
> > > # luksDump
> > > root@ubuntu:/etc/cryptkeys# cryptsetup luksDump /dev/sda5
> > > LUKS header information for /dev/sda5
> > > 
> > > Version:       	1
> > > Cipher name:   	aes
> > > Cipher mode:   	cbc-essiv:sha256
> > > Hash spec:     	sha1
> > > Payload offset:	2056
> > > MK bits:       	256
> > > MK digest:     	25 a3 74 7e 25 fd a4 a6 18 b7 a7 63 da 95 68 26 6c da 55 4c 
> > > MK salt:       	df 87 4a c3 0d 93 5a a9 3a 49 71 33 d4 4a ba bc 
> > >                	ca b7 ef d6 cd 89 41 16 6c eb 61 5d 2a 73 2b a5 
> > > MK iterations: 	10
> > > UUID:          	bb827496-8fe5-4c55-9b76-1373d850c548
> > > 
> > > Key Slot 0: ENABLED
> > > 	Iterations:         	173012
> > > 	Salt:               	74 03 b2 a6 3c 36 95 28 bb 7f 1b e3 fc ec 84 14 
> > > 	                      	6f ee 17 fc 63 7a 33 53 60 5e 43 9f 8a dd 1a 18 
> > > 	Key material offset:	8
> > > 	AF stripes:            	4000
> > > Key Slot 1: DISABLED
> > > Key Slot 2: DISABLED
> > > Key Slot 3: DISABLED
> > > Key Slot 4: DISABLED
> > > Key Slot 5: DISABLED
> > > Key Slot 6: DISABLED
> > > Key Slot 7: DISABLED
> > > 
> > 
> > > _______________________________________________
> > > dm-crypt mailing list
> > > dm-crypt@saout.de
> > > http://www.saout.de/mailman/listinfo/dm-crypt
> > 
> > 
> 
> 

> _______________________________________________
> dm-crypt mailing list
> dm-crypt@saout.de
> http://www.saout.de/mailman/listinfo/dm-crypt


-- 
Arno Wagner, Dr. sc. techn., Dipl. Inform., CISSP -- Email: arno@wagner.name 
GnuPG:  ID: 1E25338F  FP: 0C30 5782 9D93 F785 E79C  0296 797F 6B50 1E25 338F
----
Cuddly UI's are the manifestation of wishful thinking. -- Dylan Evans

If it's in the news, don't worry about it.  The very definition of 
"news" is "something that hardly ever happens." -- Bruce Schneier 

  reply	other threads:[~2010-09-03 18:16 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2010-09-03  4:24 [dm-crypt] Can't add a new key, "No key available with this passphrase" PsiStormYamato
2010-09-03  7:30 ` Arno Wagner
2010-09-03 15:36   ` PsiStormYamato
2010-09-03 18:16     ` Arno Wagner [this message]
2010-09-03 18:46       ` Arno Wagner
     [not found]       ` <1283542740.2186.12.camel@shadowtek.localdomain>
2010-09-04  9:12         ` Arno Wagner
2010-09-05  9:54           ` Milan Broz

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20100903181646.GB11768@tansi.org \
    --to=arno@wagner.name \
    --cc=dm-crypt@saout.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.