From: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To: Naveen Kumar GADDIPATI <naveen.gaddipati@stericsson.com>
Cc: Trilok Soni <tsoni@codeaurora.org>,
"linux-input@vger.kernel.org" <linux-input@vger.kernel.org>,
STEricsson_nomadik_linux <STEricsson_nomadik_linux@list.st.com>,
Henrik Rydberg <rydberg@euromail.se>
Subject: Re: [Patch v2] input:rohm based bu21013 touch panel controller driver support
Date: Thu, 9 Sep 2010 09:01:40 -0700 [thread overview]
Message-ID: <20100909160140.GC19937@core.coreip.homeip.net> (raw)
In-Reply-To: <20100909155918.GB19937@core.coreip.homeip.net>
On Thu, Sep 09, 2010 at 08:59:19AM -0700, Dmitry Torokhov wrote:
> Hi Naveen,
>
> On Thu, Sep 09, 2010 at 01:36:12PM +0200, Naveen Kumar GADDIPATI wrote:
> > Hi Dmitry,
> >
> > From: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
> >
> > Added the ROHM based bu21013 capacitive touch panel controller
> > driver support with i2c interface.
> >
> > Acked-by: Linus Walleij <linus.walleij@stericsson.com>
> > Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
>
> Thank you for making the changes.
>
> Henrik, could you glance over MT handling please?
Argh, now really adding Henrik...
>
> > ---
> > Modifications in v2:
> > --Updated with the Dmitry comments on Patch v1
> > --Updated with the Trilok comments on Patch v1
> >
> >
> > drivers/input/touchscreen/Kconfig | 12 +
> > drivers/input/touchscreen/Makefile | 1 +
> > drivers/input/touchscreen/bu21013_ts.c | 770 ++++++++++++++++++++++++++++++++
> > include/linux/input/bu21013.h | 44 ++
> > 4 files changed, 827 insertions(+), 0 deletions(-)
> > create mode 100644 drivers/input/touchscreen/bu21013_ts.c
> > create mode 100644 include/linux/input/bu21013.h
> >
> > diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
> > index 0069d97..2380533 100644
> > --- a/drivers/input/touchscreen/Kconfig
> > +++ b/drivers/input/touchscreen/Kconfig
> > @@ -98,6 +98,18 @@ config TOUCHSCREEN_BITSY
> > To compile this driver as a module, choose M here: the
> > module will be called h3600_ts_input.
> >
> > +config TOUCHSCREEN_BU21013
> > + tristate "BU21013 based touch panel controllers"
> > + depends on I2C
> > + help
> > + Say Y here if you have a bu21013 touchscreen connected to
> > + your system.
> > +
> > + If unsure, say N.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called bu21013_ts.
> > +
> > config TOUCHSCREEN_CY8CTMG110
> > tristate "cy8ctmg110 touchscreen"
> > depends on I2C
> > diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
> > index 28217e1..a0a2021 100644
> > --- a/drivers/input/touchscreen/Makefile
> > +++ b/drivers/input/touchscreen/Makefile
> > @@ -14,6 +14,7 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879_SPI) += ad7879-spi.o
> > obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o
> > obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o
> > obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o
> > +obj-$(CONFIG_TOUCHSCREEN_BU21013) += bu21013_ts.o
> > obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110) += cy8ctmg110_ts.o
> > obj-$(CONFIG_TOUCHSCREEN_DA9034) += da9034-ts.o
> > obj-$(CONFIG_TOUCHSCREEN_DYNAPRO) += dynapro.o
> > diff --git a/drivers/input/touchscreen/bu21013_ts.c b/drivers/input/touchscreen/bu21013_ts.c
> > new file mode 100644
> > index 0000000..117d9c5
> > --- /dev/null
> > +++ b/drivers/input/touchscreen/bu21013_ts.c
> > @@ -0,0 +1,770 @@
> > +/*
> > + * Copyright (C) ST-Ericsson SA 2010
> > + * Author: Naveen Kumar G <naveen.gaddipati@stericsson.com> for ST-Ericsson
> > + * License terms:GNU General Public License (GPL) version 2
> > + */
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/init.h>
> > +#include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/i2c.h>
> > +#include <linux/workqueue.h>
> > +#include <linux/input.h>
> > +#include <linux/types.h>
> > +#include <linux/timer.h>
> > +#include <linux/input/bu21013.h>
> > +#include <linux/slab.h>
> > +
> > +#define PEN_DOWN_INTR 0
> > +#define PEN_UP_INTR 1
> > +#define RESET_DELAY 30
> > +#define POLLING_DELAY 100
> > +#define MAX_TOOL_WIDTH 15
> > +#define MAX_TOUCH_MAJOR 255
> > +#define MAX_TOUCH_MINOR 15
> > +#define MAX_PRESSURE 1
> > +#define PENUP_TIMEOUT (2)
> > +#define DELTA_MIN 16
> > +#define MASK_BITS 0x03
> > +#define SHIFT_8 8
> > +#define SHIFT_2 2
> > +#define LENGTH_OF_BUFFER 11
> > +
> > +#define BU21013_SENSORS_BTN_0_7_REG 0x70
> > +#define BU21013_SENSORS_BTN_8_15_REG 0x71
> > +#define BU21013_SENSORS_BTN_16_23_REG 0x72
> > +#define BU21013_X1_POS_MSB_REG 0x73
> > +#define BU21013_X1_POS_LSB_REG 0x74
> > +#define BU21013_Y1_POS_MSB_REG 0x75
> > +#define BU21013_Y1_POS_LSB_REG 0x76
> > +#define BU21013_X2_POS_MSB_REG 0x77
> > +#define BU21013_X2_POS_LSB_REG 0x78
> > +#define BU21013_Y2_POS_MSB_REG 0x79
> > +#define BU21013_Y2_POS_LSB_REG 0x7A
> > +#define BU21013_INT_CLR_REG 0xE8
> > +#define BU21013_INT_MODE_REG 0xE9
> > +#define BU21013_GAIN_REG 0xEA
> > +#define BU21013_OFFSET_MODE_REG 0xEB
> > +#define BU21013_XY_EDGE_REG 0xEC
> > +#define BU21013_RESET_REG 0xED
> > +#define BU21013_CALIB_REG 0xEE
> > +#define BU21013_DONE_REG 0xEF
> > +#define BU21013_SENSOR_0_7_REG 0xF0
> > +#define BU21013_SENSOR_8_15_REG 0xF1
> > +#define BU21013_SENSOR_16_23_REG 0xF2
> > +#define BU21013_POS_MODE1_REG 0xF3
> > +#define BU21013_POS_MODE2_REG 0xF4
> > +#define BU21013_CLK_MODE_REG 0xF5
> > +#define BU21013_IDLE_REG 0xFA
> > +#define BU21013_FILTER_REG 0xFB
> > +#define BU21013_TH_ON_REG 0xFC
> > +#define BU21013_TH_OFF_REG 0xFD
> > +
> > +#define BU21013_RESET_ENABLE 0x01
> > +
> > +#define BU21013_SENSORS_EN_0_7 0x3F
> > +#define BU21013_SENSORS_EN_8_15 0xFC
> > +#define BU21013_SENSORS_EN_16_23 0x1F
> > +
> > +#define BU21013_POS_MODE1_0 0x02
> > +#define BU21013_POS_MODE1_1 0x04
> > +#define BU21013_POS_MODE1_2 0x08
> > +
> > +#define BU21013_POS_MODE2_ZERO 0x01
> > +#define BU21013_POS_MODE2_AVG1 0x02
> > +#define BU21013_POS_MODE2_AVG2 0x04
> > +#define BU21013_POS_MODE2_EN_XY 0x08
> > +#define BU21013_POS_MODE2_EN_RAW 0x10
> > +#define BU21013_POS_MODE2_MULTI 0x80
> > +
> > +#define BU21013_CLK_MODE_DIV 0x01
> > +#define BU21013_CLK_MODE_EXT 0x02
> > +#define BU21013_CLK_MODE_CALIB 0x80
> > +
> > +#define BU21013_IDLET_0 0x01
> > +#define BU21013_IDLET_1 0x02
> > +#define BU21013_IDLET_2 0x04
> > +#define BU21013_IDLET_3 0x08
> > +#define BU21013_IDLE_INTERMIT_EN 0x10
> > +
> > +#define BU21013_DELTA_0_6 0x7F
> > +#define BU21013_FILTER_EN 0x80
> > +
> > +#define BU21013_INT_MODE_LEVEL 0x00
> > +#define BU21013_INT_MODE_EDGE 0x01
> > +
> > +#define BU21013_GAIN_0 0x01
> > +#define BU21013_GAIN_1 0x02
> > +#define BU21013_GAIN_2 0x04
> > +
> > +#define BU21013_OFFSET_MODE_DEFAULT 0x00
> > +#define BU21013_OFFSET_MODE_MOVE 0x01
> > +#define BU21013_OFFSET_MODE_DISABLE 0x02
> > +
> > +#define BU21013_TH_ON_0 0x01
> > +#define BU21013_TH_ON_1 0x02
> > +#define BU21013_TH_ON_2 0x04
> > +#define BU21013_TH_ON_3 0x08
> > +#define BU21013_TH_ON_4 0x10
> > +#define BU21013_TH_ON_5 0x20
> > +#define BU21013_TH_ON_6 0x40
> > +#define BU21013_TH_ON_7 0x80
> > +#define BU21013_TH_ON_MAX 0xFF
> > +
> > +#define BU21013_TH_OFF_0 0x01
> > +#define BU21013_TH_OFF_1 0x02
> > +#define BU21013_TH_OFF_2 0x04
> > +#define BU21013_TH_OFF_3 0x08
> > +#define BU21013_TH_OFF_4 0x10
> > +#define BU21013_TH_OFF_5 0x20
> > +#define BU21013_TH_OFF_6 0x40
> > +#define BU21013_TH_OFF_7 0x80
> > +#define BU21013_TH_OFF_MAX 0xFF
> > +
> > +#define BU21013_X_EDGE_0 0x01
> > +#define BU21013_X_EDGE_1 0x02
> > +#define BU21013_X_EDGE_2 0x04
> > +#define BU21013_X_EDGE_3 0x08
> > +#define BU21013_Y_EDGE_0 0x10
> > +#define BU21013_Y_EDGE_1 0x20
> > +#define BU21013_Y_EDGE_2 0x40
> > +#define BU21013_Y_EDGE_3 0x80
> > +
> > +#define BU21013_DONE 0x01
> > +#define BU21013_NUMBER_OF_X_SENSORS (6)
> > +#define BU21013_NUMBER_OF_Y_SENSORS (11)
> > +
> > +#define DRIVER_TP "bu21013_tp"
> > +
> > +/**
> > + * struct bu21013_ts_data - touch panel data structure
> > + * @client: pointer to the i2c client
> > + * @chip: pointer to the touch panel controller
> > + * @in_dev: pointer to the input device structure
> > + * @wait: variable to wait_queue_head_t structure
> > + * @intr_pin: interrupt pin value
> > + * @touch_stopped: touch stop flag
> > + * @x_pos: x position for two co-ordinates
> > + * @y_pos: y position for two co-ordinates
> > + * @previous_press_reported: last reported flag
> > + *
> > + * Touch panel device data structure
> > + */
> > +struct bu21013_ts_data {
> > + struct i2c_client *client;
> > + struct bu21013_platform_device *chip;
>
> Please make int "const".
>
> > + struct input_dev *in_dev;
> > + wait_queue_head_t wait;
> > + bool touch_stopped;
> > + unsigned int intr_pin;
> > + signed short x_pos[2];
> > + signed short y_pos[2];
> > + bool previous_press_reported;
> > +};
> > +
> > +/**
> > + * bu21013_report_pen_down() - reports the pen down event
> > + * @data:bu21013_ts_data structure pointer
> > + * @count:touch count
> > + *
> > + * This function used to report the pen down interrupt to
> > + * input subsystem and returns none
> > + */
> > +static void bu21013_report_pen_down(struct bu21013_ts_data *data, int count)
> > +{
> > + int i;
> > +
> > + input_report_abs(data->in_dev, ABS_X, data->x_pos[0]);
> > + input_report_abs(data->in_dev, ABS_Y, data->y_pos[0]);
> > + input_report_key(data->in_dev, BTN_TOUCH, count);
> > +
> > + if (data->chip->multi_touch) {
>
> Why would we want to condition this? If hardware is capable of MT we
> should always support it.
>
> > + for (i = 0; i < count; i++) {
> > + input_report_abs(data->in_dev, ABS_MT_POSITION_X,
> > + data->x_pos[i]);
> > + input_report_abs(data->in_dev, ABS_MT_POSITION_Y,
> > + data->y_pos[i]);
> > + input_mt_sync(data->in_dev);
> > + }
> > + }
> > + input_sync(data->in_dev);
> > + data->previous_press_reported = count;
> > +}
> > +/**
> > + * bu21013_report_pen_up() - reports the pen up event
> > + * @data:bu21013_ts_data structure pointer
> > + *
> > + * This function used to report the pen up interrupt
> > + * to input subsystem and returns none
> > + */
> > +static void bu21013_report_pen_up(struct bu21013_ts_data *data)
> > +{
> > + input_report_key(data->in_dev, BTN_TOUCH, 0);
> > + if (data->chip->multi_touch) {
> > + input_report_key(data->in_dev, BTN_2, 0);
>
> Remnants of old patch... please remove.
>
> > + input_mt_sync(data->in_dev);
> > + }
> > + input_sync(data->in_dev);
> > + data->previous_press_reported = 0;
>
> = false;
>
> > +}
> > +/**
> > + * bu21013_touch_calc() - calculates the co-ordinates delta
> > + * @data: bu21013_ts_data structure pointer
> > + * @x: x position
> > + * @y: y position
> > + * @count: touch count
> > + *
> > + * This function calculates the exact co-ordinates with respect to
> > + * display resolution and returns none
> > + */
> > +static void bu21013_touch_calc
> > + (struct bu21013_ts_data *data, int x, int y, int count)
> > +{
> > + data->x_pos[count] = x;
> > + data->y_pos[count] = y;
> > + if (data->chip->x_flip)
> > + data->x_pos[count] =
> > + data->chip->touch_x_max - data->x_pos[count];
> > + if (data->chip->y_flip)
> > + data->y_pos[count] =
> > + data->chip->touch_y_max - data->y_pos[count];
> > +}
> > +/**
> > + * bu21013_verify_delta() - verify the co-ordinates delta
> > + * @x1: x1 position
> > + * @y1: y1 position
> > + * @x2: x2 position
> > + * @y2: y2 position
> > + *
> > + * This function verifies the delta of the
> > + * co-ordinates and returns boolean.
> > + */
> > +static bool bu21013_verify_delta(int x1, int y1, int x2, int y2)
> > +{
> > + int delta_x, delta_y;
> > +
> > + if ((x1 != 0) && (y1 != 0)) {
> > + delta_x = x2 - x1;
> > + if (x1 > x2)
> > + delta_x = x1 - x2;
> > + delta_y = y2 - y1;
> > + if (y1 > y2)
> > + delta_y = y1 - y2;
> > + if ((delta_x < DELTA_MIN) || (delta_y < DELTA_MIN))
> > + return false;
> > + }
> > + return true;
>
> Hmm, I remember - the fuzz handling indeed will not work for MT A protocol.
> Still, I do not think it is correct. Don't you need to do
> "abs(delta_x) < DELTA_MIN"?
>
> > +}
> > +
> > +/**
> > + * bu21013_do_touch_report(): Get the touch co-ordinates
> > + * @data:bu21013_ts_data structure pointer
> > + *
> > + * Get the touch co-ordinates from touch sensor registers and writes
> > + * into device structure and returns integer.
> > + */
> > +static int bu21013_do_touch_report(struct bu21013_ts_data *data)
> > +{
> > + u8 buf[LENGTH_OF_BUFFER];
> > + int finger1_valid = 0;
> > + int finger2_valid = 0;
> > + unsigned int finger1_pos_x;
> > + unsigned int finger1_pos_y;
> > + unsigned int finger2_pos_x = 0;
> > + unsigned int finger2_pos_y = 0;
> > + int number_of_active_x_sensors;
> > + int number_of_active_y_sensors;
> > + int total_number_of_active_sensors;
> > + int finger_down_count = 0;
> > + int ret = 0;
> > +
> > + if (data == NULL)
> > + return -EINVAL;
> > +
> > + ret = i2c_smbus_read_i2c_block_data(data->client,
> > + BU21013_SENSORS_BTN_0_7_REG,
> > + LENGTH_OF_BUFFER, buf);
> > + if (ret < LENGTH_OF_BUFFER)
> > + return -EINVAL;
> > +
> > + number_of_active_x_sensors = hweight32(buf[0] &
> > + BU21013_SENSORS_EN_0_7);
> > + number_of_active_y_sensors = hweight32(
> > + ((buf[1] & BU21013_SENSORS_EN_8_15) |
> > + ((buf[2] & BU21013_SENSORS_EN_16_23) << SHIFT_8)) >> SHIFT_2);
> > + if (((number_of_active_x_sensors != 0) &&
> > + (number_of_active_y_sensors == 0)) ||
> > + ((number_of_active_x_sensors == 0) &&
> > + (number_of_active_y_sensors != 0)))
> > + return 0;
> > +
> > + total_number_of_active_sensors =
> > + number_of_active_x_sensors + number_of_active_y_sensors;
> > +
> > + finger1_pos_x = buf[3] << SHIFT_2 | (buf[4] & MASK_BITS);
> > + finger1_pos_y = buf[5] << SHIFT_2 | (buf[6] & MASK_BITS);
> > +
> > + if (data->chip->multi_touch) {
> > + finger2_pos_x = buf[7] << SHIFT_2 | (buf[8] & MASK_BITS);
> > + finger2_pos_y = buf[9] << SHIFT_2 | (buf[10] & MASK_BITS);
> > + }
> > +
> > + if (total_number_of_active_sensors) {
> > + if ((finger2_pos_x != 0) && (finger2_pos_y != 0)) {
> > + if ((finger1_pos_x == 0) || (finger1_pos_y == 0))
> > + return 0;
> > + ret = bu21013_verify_delta(finger1_pos_x,
> > + finger1_pos_y, finger2_pos_x, finger2_pos_y);
> > + if (!ret)
> > + total_number_of_active_sensors = 0;
> > + }
> > + }
> > +
> > + if (total_number_of_active_sensors) {
> > + finger1_valid = 1;
> > + if ((finger1_pos_x == 0) || (finger1_pos_y == 0) ||
> > + (finger1_pos_x >= data->chip->touch_x_max) ||
> > + (finger1_pos_y >= data->chip->touch_y_max))
> > + finger1_valid = 0;
> > + finger2_valid = 1;
> > + if ((finger2_pos_x == 0) || (finger2_pos_y == 0) ||
> > + (finger2_pos_x >= data->chip->touch_x_max) ||
> > + (finger2_pos_y >= data->chip->touch_y_max))
> > + finger2_valid = 0;
> > + if ((finger1_valid == 0) && (finger2_valid == 0))
> > + return 0;
> > + if (finger1_valid) {
> > + bu21013_touch_calc(data, finger1_pos_x,
> > + finger1_pos_y, finger_down_count);
> > + finger_down_count++;
> > + }
> > + if (finger2_valid) {
> > + bu21013_touch_calc(data, finger2_pos_x,
> > + finger2_pos_y, finger_down_count);
> > + finger_down_count++;
> > + }
> > + }
> > +
> > + if (finger_down_count > 0)
> > + bu21013_report_pen_down(data, finger_down_count);
> > + else {
> > + if (data->previous_press_reported)
> > + bu21013_report_pen_up(data);
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +/**
> > + * bu21013_gpio_irq() - gpio thread function for touch interrupt
> > + * @irq: irq value
> > + * @device_data:void pointer
> > + *
> > + * This gpio thread function for touch interrupt
> > + * and returns irqreturn_t.
> > + */
> > +static irqreturn_t bu21013_gpio_irq(int irq, void *device_data)
> > +{
> > + struct bu21013_ts_data *data = device_data;
> > + struct i2c_client *i2c = data->client;
> > + int retval;
> > +
> > + do {
> > + retval = bu21013_do_touch_report(data);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "bu21013_do_touch_report failed\n");
> > + return IRQ_NONE;
> > + }
> > +
> > + data->intr_pin = data->chip->irq_read_val();
> > + if (data->intr_pin == PEN_DOWN_INTR)
> > + wait_event_timeout(data->wait, data->touch_stopped,
> > + msecs_to_jiffies(10));
> > + } while (!data->intr_pin && !data->touch_stopped);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +/**
> > + * bu21013_init_chip() - power on sequence for the bu21013 controller
> > + * @data: device structure pointer
> > + *
> > + * This function is used to power on
> > + * the bu21013 controller and returns integer.
> > + */
> > +static int bu21013_init_chip(struct bu21013_ts_data *data)
> > +{
> > + int retval;
> > + struct i2c_client *i2c = data->client;
> > +
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_RESET_REG,
> > + BU21013_RESET_ENABLE);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_RESET reg write failed\n");
> > + goto err;
> > + }
> > + msleep(RESET_DELAY);
> > +
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_0_7_REG,
> > + BU21013_SENSORS_EN_0_7);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_SENSOR_0_7 reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_8_15_REG,
> > + BU21013_SENSORS_EN_8_15);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_SENSOR_8_15 reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_16_23_REG,
> > + BU21013_SENSORS_EN_16_23);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_SENSOR_16_23 reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE1_REG,
> > + (BU21013_POS_MODE1_0 | BU21013_POS_MODE1_1));
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_POS_MODE1 reg write failed\n");
> > + goto err;
> > + }
> > + if (data->chip->multi_touch)
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE2_REG,
> > + (BU21013_POS_MODE2_ZERO | BU21013_POS_MODE2_AVG1 |
> > + BU21013_POS_MODE2_AVG2 | BU21013_POS_MODE2_EN_RAW |
> > + BU21013_POS_MODE2_MULTI));
> > + else
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE2_REG,
> > + (BU21013_POS_MODE2_ZERO | BU21013_POS_MODE2_AVG1 |
> > + BU21013_POS_MODE2_AVG2 | BU21013_POS_MODE2_EN_RAW));
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_POS_MODE2 reg write failed\n");
> > + goto err;
> > + }
> > + if (data->chip->ext_clk)
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_CLK_MODE_REG,
> > + (BU21013_CLK_MODE_EXT | BU21013_CLK_MODE_CALIB));
> > + else
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_CLK_MODE_REG,
> > + (BU21013_CLK_MODE_DIV | BU21013_CLK_MODE_CALIB));
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_CLK_MODE reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_IDLE_REG,
> > + (BU21013_IDLET_0 | BU21013_IDLE_INTERMIT_EN));
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_IDLE reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_INT_MODE_REG,
> > + BU21013_INT_MODE_LEVEL);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_INT_MODE reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_FILTER_REG,
> > + (BU21013_DELTA_0_6 |
> > + BU21013_FILTER_EN));
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_FILTER reg write failed\n");
> > + goto err;
> > + }
> > +
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_ON_REG,
> > + (BU21013_TH_ON_3 | BU21013_TH_ON_4));
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_TH_ON reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_OFF_REG,
> > + BU21013_TH_OFF_4);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_TH_OFF reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_GAIN_REG,
> > + (BU21013_GAIN_0 | BU21013_GAIN_1));
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_GAIN reg write failed\n");
> > + goto err;
> > + }
> > +
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_OFFSET_MODE_REG,
> > + BU21013_OFFSET_MODE_DEFAULT);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_OFFSET_MODE reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_XY_EDGE_REG,
> > + (BU21013_X_EDGE_0 | BU21013_X_EDGE_2 |
> > + BU21013_Y_EDGE_1 | BU21013_Y_EDGE_3));
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_XY_EDGE reg write failed\n");
> > + goto err;
> > + }
> > + retval = i2c_smbus_write_byte_data(i2c, BU21013_DONE_REG,
> > + BU21013_DONE);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "BU21013_REG_DONE reg write failed\n");
> > + goto err;
> > + }
> > +
> > + data->x_pos[0] = 0;
> > + data->x_pos[1] = 0;
> > + data->y_pos[0] = 0;
> > + data->y_pos[1] = 0;
> > + data->previous_press_reported = 0;
> > +
> > +err:
> > + return retval;
> > +}
> > +
> > +#ifdef CONFIG_PM
> > +/**
> > + * bu21013_suspend() - suspend the touch screen controller
> > + * @client: pointer to i2c client structure
> > + * @mesg: message from power manager
> > + *
> > + * This funtion is used to suspend the
> > + * touch panel controller and returns integer
> > + */
> > +static int bu21013_suspend(struct i2c_client *client, pm_message_t mesg)
> > +{
> > + struct bu21013_ts_data *bu21013_data = i2c_get_clientdata(client);
> > +
> > + bu21013_data->touch_stopped = true;
> > + wake_up(&bu21013_data->wait);
> > + if (device_may_wakeup(&client->dev))
> > + enable_irq_wake(bu21013_data->chip->irq);
> > + else
> > + disable_irq(bu21013_data->chip->irq);
> > +
> > + return 0;
> > +}
> > +
> > +/**
> > + * bu21013_resume() - resume the touch screen controller
> > + * @client: pointer to i2c client structure
> > + *
> > + * This funtion is used to resume the touch panel
> > + * controller and returns integer.
> > + */
> > +static int bu21013_resume(struct i2c_client *client)
> > +{
> > + int retval;
> > + struct bu21013_ts_data *bu21013_data = i2c_get_clientdata(client);
> > +
> > + retval = bu21013_init_chip(bu21013_data);
> > + if (retval < 0) {
> > + dev_err(&client->dev, "tsc config failed\n");
> > + return retval;
> > + }
> > +
> > + bu21013_data->touch_stopped = false;
> > + if (device_may_wakeup(&client->dev))
> > + disable_irq_wake(bu21013_data->chip->irq);
> > + else
> > + enable_irq(bu21013_data->chip->irq);
> > +
> > + return 0;
> > +}
> > +#endif
> > +
> > +/**
> > + * bu21013_probe() - initialzes the i2c-client touchscreen driver
> > + * @i2c: i2c client structure pointer
> > + * @id:i2c device id pointer
> > + *
> > + * This function used to initializes the i2c-client touchscreen
> > + * driver and returns integer.
> > + */
> > +static int __devinit bu21013_probe(struct i2c_client *i2c,
> > + const struct i2c_device_id *id)
> > +{
> > + int retval;
> > + struct bu21013_ts_data *bu21013_data;
> > + struct input_dev *in_dev;
> > + short x_max;
> > + short y_max;
> > + struct bu21013_platform_device *pdata = i2c->dev.platform_data;
> > +
> > + if (!i2c) {
> > + dev_err(&i2c->dev, "i2c client not defined\n");
> > + retval = -EINVAL;
> > + return retval;
> > + }
> > +
> > + if (!pdata) {
> > + dev_err(&i2c->dev, "platform data not defined\n");
> > + retval = -EINVAL;
> > + return retval;
> > + }
> > +
> > + bu21013_data = kzalloc(sizeof(struct bu21013_ts_data), GFP_KERNEL);
> > + if (!bu21013_data) {
> > + dev_err(&i2c->dev, "device memory alloc failed\n");
> > + retval = -ENOMEM;
> > + return retval;
> > + }
> > +
> > + /* allocate input device */
> > + in_dev = input_allocate_device();
> > + if (!in_dev) {
> > + dev_err(&i2c->dev, "input device memory alloc failed\n");
> > + retval = -ENOMEM;
> > + goto err_alloc;
> > + }
> > + bu21013_data->in_dev = in_dev;
> > +
> > + bu21013_data->chip = pdata;
> > + bu21013_data->client = i2c;
> > + bu21013_data->touch_stopped = false;
> > +
> > + x_max = pdata->x_max_res;
> > + y_max = pdata->y_max_res;
> > +
> > + init_waitqueue_head(&bu21013_data->wait);
> > +
> > + i2c_set_clientdata(i2c, bu21013_data);
> > +
> > + /* configure the gpio pins */
> > + if (pdata->cs_en) {
> > + retval = pdata->cs_en(pdata->cs_pin);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "chip init failed\n");
> > + goto err_init_cs;
> > + }
> > + }
> > +
> > + /* configure the touch panel controller */
> > + retval = bu21013_init_chip(bu21013_data);
> > + if (retval < 0) {
> > + dev_err(&i2c->dev, "error in bu21013 config\n");
> > + goto err_init_config;
> > + }
> > +
> > + /* register the device to input subsystem */
> > + in_dev->name = DRIVER_TP;
> > + in_dev->id.bustype = BUS_I2C;
> > + in_dev->dev.parent = &i2c->dev;
> > + __set_bit(EV_SYN, in_dev->evbit);
> > + __set_bit(EV_KEY, in_dev->evbit);
> > + __set_bit(EV_ABS, in_dev->evbit);
> > + __set_bit(BTN_TOUCH, in_dev->keybit);
> > +
> > + input_set_abs_params(in_dev, ABS_X, 0, x_max, 0, 0);
> > + input_set_abs_params(in_dev, ABS_Y, 0, y_max, 0, 0);
> > + input_set_abs_params(in_dev, ABS_PRESSURE, 0, MAX_PRESSURE, 0, 0);
> > + input_set_abs_params(in_dev, ABS_TOOL_WIDTH, 0, MAX_TOOL_WIDTH, 0, 0);
> > +
> > + if (pdata->multi_touch) {
> > + input_set_abs_params(in_dev, ABS_MT_POSITION_X, 0, x_max,
> > + 0, 0);
> > + input_set_abs_params(in_dev, ABS_MT_POSITION_Y, 0, y_max,
> > + 0, 0);
> > + input_set_abs_params(in_dev, ABS_MT_TOUCH_MAJOR, 0,
> > + MAX_TOUCH_MAJOR, 0, 0);
> > + input_set_abs_params(in_dev, ABS_MT_TOUCH_MINOR, 0,
> > + MAX_TOUCH_MINOR, 0, 0);
> > + input_set_abs_params(in_dev, ABS_MT_ORIENTATION, 0, 1, 0, 0);
> > + input_set_abs_params(in_dev, ABS_MT_WIDTH_MAJOR, 0,
> > + MAX_TOOL_WIDTH, 0, 0);
>
> If we are not sending events we should not declare capabilities either.
>
> > + }
> > + retval = input_register_device(in_dev);
> > + if (retval)
> > + goto err_input_register;
> > +
> > + retval = request_threaded_irq(pdata->irq, NULL, bu21013_gpio_irq,
> > + (IRQF_TRIGGER_FALLING | IRQF_SHARED),
> > + DRIVER_TP, bu21013_data);
> > + if (retval) {
> > + dev_err(&i2c->dev, "request irq %d failed\n", pdata->irq);
> > + goto err_init_irq;
> > + }
> > +
> > + return retval;
> > +
> > +err_init_irq:
> > + input_unregister_device(bu21013_data->in_dev);
> > + bu21013_data->in_dev = NULL;
> > +err_input_register:
> > +err_init_config:
> > + pdata->cs_dis(pdata->cs_pin);
> > +err_init_cs:
> > + input_free_device(bu21013_data->in_dev);
> > +err_alloc:
> > + kfree(bu21013_data);
> > +
> > + return retval;
> > +}
> > +/**
> > + * bu21013_remove() - removes the i2c-client touchscreen driver
> > + * @client: i2c client structure pointer
> > + *
> > + * This function uses to remove the i2c-client
> > + * touchscreen driver and returns integer.
> > + */
> > +static int __devexit bu21013_remove(struct i2c_client *client)
> > +{
> > + struct bu21013_ts_data *data = i2c_get_clientdata(client);
> > +
> > + data->touch_stopped = true;
> > + free_irq(data->chip->irq, data);
> > + data->chip->cs_dis(data->chip->cs_pin);
> > + input_unregister_device(data->in_dev);
> > + kfree(data);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct i2c_device_id bu21013_id[] = {
> > + { DRIVER_TP, 0 },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(i2c, bu21013_id);
> > +
> > +static struct i2c_driver bu21013_driver = {
> > + .driver = {
> > + .name = DRIVER_TP,
> > + .owner = THIS_MODULE,
> > + },
> > + .probe = bu21013_probe,
> > +#ifdef CONFIG_PM
> > + .suspend = bu21013_suspend,
> > + .resume = bu21013_resume,
> > +#endif
> > + .remove = __devexit_p(bu21013_remove),
> > + .id_table = bu21013_id,
> > +};
> > +
> > +/**
> > + * bu21013_init() - initializes the bu21013 touchscreen driver
> > + *
> > + * This function used to initializes the bu21013
> > + * touchscreen driver and returns integer.
> > + */
> > +static int __init bu21013_init(void)
> > +{
> > + return i2c_add_driver(&bu21013_driver);
> > +}
> > +
> > +/**
> > + * bu21013_exit() - de-initializes the bu21013 touchscreen driver
> > + *
> > + * This function uses to de-initializes the bu21013
> > + * touchscreen driver and returns none.
> > + */
> > +static void __exit bu21013_exit(void)
> > +{
> > + i2c_del_driver(&bu21013_driver);
> > +}
> > +
> > +module_init(bu21013_init);
> > +module_exit(bu21013_exit);
> > +
> > +MODULE_LICENSE("GPL v2");
> > +MODULE_AUTHOR("NAVEEN KUMAR G<naveen.gaddipati@stericsson.com");
> > +MODULE_DESCRIPTION("bu21013 touch screen controller driver");
> > diff --git a/include/linux/input/bu21013.h b/include/linux/input/bu21013.h
> > new file mode 100644
> > index 0000000..6c64bda
> > --- /dev/null
> > +++ b/include/linux/input/bu21013.h
> > @@ -0,0 +1,44 @@
> > +/*
> > + * Copyright (C) ST-Ericsson SA 2010
> > + * Author: Naveen Kumar G <naveen.gaddipati@stericsson.com> for ST-Ericsson
> > + * License terms:GNU General Public License (GPL) version 2
> > + */
> > +
> > +#ifndef _BU21013_H
> > +#define _BU21013_H
> > +
> > +/**
> > + * struct bu21013_platform_device - Handle the platform data
> > + * @cs_en: pointer to the cs enable function
> > + * @cs_dis: pointer to the cs disable function
> > + * @irq_read_val: pointer to read the pen irq value function
> > + * @x_max_res: xmax resolution
> > + * @y_max_res: ymax resolution
> > + * @touch_x_max: touch x max
> > + * @touch_y_max: touch y max
> > + * @cs_pin: chip select pin
> > + * @irq: irq pin
> > + * @ext_clk: external clock flag
> > + * @x_flip: x flip flag
> > + * @y_flip: y flip flag
> > + * @multi_touch: multi_touch flag
> > + *
> > + * This is used to handle the platform data
> > + */
> > +struct bu21013_platform_device {
> > + int (*cs_en)(int reset_pin);
> > + int (*cs_dis)(int reset_pin);
> > + int (*irq_read_val)(void);
> > + int x_max_res;
> > + int y_max_res;
> > + int touch_x_max;
> > + int touch_y_max;
> > + unsigned int cs_pin;
> > + unsigned int irq;
> > + bool ext_clk;
> > + bool x_flip;
> > + bool y_flip;
> > + bool multi_touch;
> > +};
> > +
> > +#endif
> > --
> > 1.7.2.dirty
> >
> > Thanks & Regards,
> > Naveen
>
> --
> Dmitry
--
Dmitry
next prev parent reply other threads:[~2010-09-09 16:01 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-09-09 11:36 [Patch v2] input:rohm based bu21013 touch panel controller driver support Naveen Kumar GADDIPATI
2010-09-09 12:10 ` Trilok Soni
2010-09-09 13:20 ` Naveen Kumar GADDIPATI
2010-09-09 13:46 ` Trilok Soni
2010-09-09 15:39 ` Dmitry Torokhov
2010-09-09 18:44 ` Trilok Soni
2010-09-09 15:59 ` Dmitry Torokhov
2010-09-09 16:01 ` Dmitry Torokhov [this message]
2010-09-09 18:26 ` Henrik Rydberg
2010-09-13 10:12 ` Naveen Kumar GADDIPATI
2010-09-13 14:36 ` Henrik Rydberg
-- strict thread matches above, loose matches on Subject: below --
2010-09-09 12:12 Naveen Kumar GADDIPATI
2010-09-09 12:13 ` Trilok Soni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20100909160140.GC19937@core.coreip.homeip.net \
--to=dmitry.torokhov@gmail.com \
--cc=STEricsson_nomadik_linux@list.st.com \
--cc=linux-input@vger.kernel.org \
--cc=naveen.gaddipati@stericsson.com \
--cc=rydberg@euromail.se \
--cc=tsoni@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.