From: Christian Lamparter <chunkeey@googlemail.com>
To: linux-wireless@vger.kernel.org
Cc: "John W. Linville" <linville@tuxdriver.com>,
Johannes Berg <johannes@sipsolutions.net>
Subject: [PATCH] mac80211: fix rx monitor filter refcounters
Date: Fri, 1 Oct 2010 23:53:20 +0200 [thread overview]
Message-ID: <201010012353.21053.chunkeey@googlemail.com> (raw)
In-Reply-To: <1285790439.3756.35.camel@jlt3.sipsolutions.net>
This patch fixes a refcounter & commit bug when monitor
rx flags are changed by:
iw dev moni set monitor [new flags]
while interface is up.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
---
On Wednesday 29 September 2010 22:00:39 Johannes wrote:
> On Wed, 2010-09-29 at 21:57 +0200, Christian wrote:
> > It's about MONITOR_FLAG_COOK_FRAMES. This flag gives me
> > headaches. I wish we could make this flag "const" and
> > don't allow it be changed by iw dev wlanX set monitor.
>
> I'm fine with not allowing the cook flag to change,
> seems like a pretty special case anyway. Or, we can
> allow it to change, but only while the interface is
> down, right?
jup, works:
command failed: Function not implemented (-38), or should
we use a different error code like -EBUSY/-EOPNOTSUPP?
---
diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index c981604..554166b 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -68,8 +68,36 @@ static int ieee80211_change_iface(struct wiphy *wiphy,
params && params->use_4addr >= 0)
sdata->u.mgd.use_4addr = params->use_4addr;
- if (sdata->vif.type == NL80211_IFTYPE_MONITOR && flags)
- sdata->u.mntr_flags = *flags;
+ if (sdata->vif.type == NL80211_IFTYPE_MONITOR && flags) {
+ struct ieee80211_local *local = sdata->local;
+
+ if (test_bit(SDATA_STATE_RUNNING, &sdata->state)) {
+ /*
+ * Prohibit MONITOR_FLAG_COOK_FRAMES to be
+ * changed while the interface is up.
+ * Else we would need to add a lot of cruft
+ * to update everything:
+ * cooked_mntrs, monitor and all fif_* counters
+ * reconfigure hardware
+ */
+ if ((*flags & MONITOR_FLAG_COOK_FRAMES) !=
+ (sdata->u.mntr_flags & MONITOR_FLAG_COOK_FRAMES))
+ return -ENOSYS;
+
+ ieee80211_adjust_monitor_flags(sdata, -1);
+ sdata->u.mntr_flags = *flags;
+ ieee80211_adjust_monitor_flags(sdata, 1);
+
+ ieee80211_configure_filter(local);
+ } else {
+ /*
+ * Because the interface is down, ieee80211_do_stop
+ * and ieee80211_do_open take care of "everything"
+ * mentioned in the comment above.
+ */
+ sdata->u.mntr_flags = *flags;
+ }
+ }
return 0;
}
diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h
index 945fbf2..f6a6d78 100644
--- a/net/mac80211/ieee80211_i.h
+++ b/net/mac80211/ieee80211_i.h
@@ -1132,6 +1132,8 @@ void ieee80211_if_remove(struct ieee80211_sub_if_data *sdata);
void ieee80211_remove_interfaces(struct ieee80211_local *local);
u32 __ieee80211_recalc_idle(struct ieee80211_local *local);
void ieee80211_recalc_idle(struct ieee80211_local *local);
+void ieee80211_adjust_monitor_flags(struct ieee80211_sub_if_data *sdata,
+ const int offset);
static inline bool ieee80211_sdata_running(struct ieee80211_sub_if_data *sdata)
{
diff --git a/net/mac80211/iface.c b/net/mac80211/iface.c
index 6678573..1300e88 100644
--- a/net/mac80211/iface.c
+++ b/net/mac80211/iface.c
@@ -148,6 +148,26 @@ static int ieee80211_check_concurrent_iface(struct ieee80211_sub_if_data *sdata,
return 0;
}
+void ieee80211_adjust_monitor_flags(struct ieee80211_sub_if_data *sdata,
+ const int offset)
+{
+ struct ieee80211_local *local = sdata->local;
+ u32 flags = sdata->u.mntr_flags;
+
+#define ADJUST(_f, _s) do { \
+ if (flags & MONITOR_FLAG_##_f) \
+ local->fif_##_s += offset; \
+ } while (0)
+
+ ADJUST(FCSFAIL, fcsfail);
+ ADJUST(PLCPFAIL, plcpfail);
+ ADJUST(CONTROL, control);
+ ADJUST(CONTROL, pspoll);
+ ADJUST(OTHER_BSS, other_bss);
+
+#undef ADJUST
+}
+
/*
* NOTE: Be very careful when changing this function, it must NOT return
* an error on interface type changes that have been pre-checked, so most
@@ -240,17 +260,7 @@ static int ieee80211_do_open(struct net_device *dev, bool coming_up)
hw_reconf_flags |= IEEE80211_CONF_CHANGE_MONITOR;
}
- if (sdata->u.mntr_flags & MONITOR_FLAG_FCSFAIL)
- local->fif_fcsfail++;
- if (sdata->u.mntr_flags & MONITOR_FLAG_PLCPFAIL)
- local->fif_plcpfail++;
- if (sdata->u.mntr_flags & MONITOR_FLAG_CONTROL) {
- local->fif_control++;
- local->fif_pspoll++;
- }
- if (sdata->u.mntr_flags & MONITOR_FLAG_OTHER_BSS)
- local->fif_other_bss++;
-
+ ieee80211_adjust_monitor_flags(sdata, 1);
ieee80211_configure_filter(local);
netif_carrier_on(dev);
@@ -477,17 +487,7 @@ static void ieee80211_do_stop(struct ieee80211_sub_if_data *sdata,
hw_reconf_flags |= IEEE80211_CONF_CHANGE_MONITOR;
}
- if (sdata->u.mntr_flags & MONITOR_FLAG_FCSFAIL)
- local->fif_fcsfail--;
- if (sdata->u.mntr_flags & MONITOR_FLAG_PLCPFAIL)
- local->fif_plcpfail--;
- if (sdata->u.mntr_flags & MONITOR_FLAG_CONTROL) {
- local->fif_pspoll--;
- local->fif_control--;
- }
- if (sdata->u.mntr_flags & MONITOR_FLAG_OTHER_BSS)
- local->fif_other_bss--;
-
+ ieee80211_adjust_monitor_flags(sdata, -1);
ieee80211_configure_filter(local);
break;
case NL80211_IFTYPE_MESH_POINT:
next prev parent reply other threads:[~2010-10-01 21:53 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-09-28 16:36 [RFC] mac80211: fix rx monitor filter refcounters Christian Lamparter
2010-09-29 7:10 ` Johannes Berg
2010-09-29 19:57 ` [RFC v2] " Christian Lamparter
2010-09-29 20:00 ` Johannes Berg
2010-10-01 21:53 ` Christian Lamparter [this message]
2010-10-02 8:46 ` [PATCH] " Johannes Berg
2010-10-02 11:17 ` [PATCH v2] " Christian Lamparter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201010012353.21053.chunkeey@googlemail.com \
--to=chunkeey@googlemail.com \
--cc=johannes@sipsolutions.net \
--cc=linux-wireless@vger.kernel.org \
--cc=linville@tuxdriver.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.