From: magnus.damm@gmail.com (Magnus Damm)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: Common GIC entry macro code
Date: Wed, 10 Nov 2010 16:00:43 +0900 [thread overview]
Message-ID: <20101110070043.18735.53764.sendpatchset@t400s> (raw)
From: Magnus Damm <damm@opensource.se>
This patch merges identical GIC demux implementations
in the file entry-macro-gic.S. The shared code in the
header file is based on the realview implementation.
Each GIC demux instance still has to setup the base address
of the controller using the get_irqnr_preamble macro. The
rest of the GIC specific code can be shared.
The omap code is excluded due to multi-omap complexity
and s5pv310 is excluded as well due to the special
"addne" instruction in the get_irqnr_and_base macro.
Signed-off-by: Magnus Damm <damm@opensource.se>
---
arch/arm/include/asm/hardware/entry-macro-gic.S | 68 +++++++++++++++++++++
arch/arm/mach-cns3xxx/include/mach/entry-macro.S | 61 ------------------
arch/arm/mach-msm/include/mach/entry-macro-qgic.S | 67 --------------------
arch/arm/mach-realview/include/mach/entry-macro.S | 60 ------------------
arch/arm/mach-tegra/include/mach/entry-macro.S | 64 -------------------
arch/arm/mach-ux500/include/mach/entry-macro.S | 67 --------------------
arch/arm/mach-vexpress/include/mach/entry-macro.S | 57 -----------------
7 files changed, 74 insertions(+), 370 deletions(-)
--- /dev/null
+++ work/arch/arm/include/asm/hardware/entry-macro-gic.S 2010-11-10 15:20:15.000000000 +0900
@@ -0,0 +1,68 @@
+/*
+ * arch/arm/include/asm/hardware/entry-macro-gic.S
+ *
+ * Low-level IRQ helper macros for GIC
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <asm/hardware/gic.h>
+
+/*
+ * The interrupt numbering scheme is defined in the
+ * interrupt controller spec. To wit:
+ *
+ * Interrupts 0-15 are IPI
+ * 16-28 are reserved
+ * 29-31 are local. We allow 30 to be used for the watchdog.
+ * 32-1020 are global
+ * 1021-1022 are reserved
+ * 1023 is "spurious" (no interrupt)
+ *
+ * For now, we ignore all local interrupts so only return an interrupt if it's
+ * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs.
+ *
+ * A simple read from the controller will tell us the number of the highest
+ * priority enabled interrupt. We then just need to check whether it is in the
+ * valid range for an IRQ (30-1020 inclusive).
+ */
+
+ .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+ ldr \irqstat, [\base, #GIC_CPU_INTACK]
+ /* bits 12-10 = src CPU, 9-0 = int # */
+
+ ldr \tmp, =1021
+ bic \irqnr, \irqstat, #0x1c00
+ cmp \irqnr, #29
+ cmpcc \irqnr, \irqnr
+ cmpne \irqnr, \tmp
+ cmpcs \irqnr, \irqnr
+ .endm
+
+/* We assume that irqstat (the raw value of the IRQ acknowledge
+ * register) is preserved from the macro above.
+ * If there is an IPI, we immediately signal end of interrupt on the
+ * controller, since this requires the original irqstat value which
+ * we won't easily be able to recreate later.
+ */
+
+ .macro test_for_ipi, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ cmp \irqnr, #16
+ strcc \irqstat, [\base, #GIC_CPU_EOI]
+ cmpcs \irqnr, \irqnr
+ .endm
+
+/* As above, this assumes that irqstat and base are preserved.. */
+
+ .macro test_for_ltirq, irqnr, irqstat, base, tmp
+ bic \irqnr, \irqstat, #0x1c00
+ mov \tmp, #0
+ cmp \irqnr, #29
+ moveq \tmp, #1
+ streq \irqstat, [\base, #GIC_CPU_EOI]
+ cmp \tmp, #0
+ .endm
--- 0001/arch/arm/mach-cns3xxx/include/mach/entry-macro.S
+++ work/arch/arm/mach-cns3xxx/include/mach/entry-macro.S 2010-11-10 15:24:56.000000000 +0900
@@ -9,7 +9,7 @@
*/
#include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
.macro disable_fiq
.endm
@@ -21,62 +21,3 @@
.macro arch_ret_to_user, tmp1, tmp2
.endm
-
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an interrupt if it's
- * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs.
- *
- * A simple read from the controller will tell us the number of the highest
- * priority enabled interrupt. We then just need to check whether it is in the
- * valid range for an IRQ (30-1020 inclusive).
- */
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
-
- ldr \tmp, =1021
-
- bic \irqnr, \irqstat, #0x1c00
-
- cmp \irqnr, #29
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
-
- .endm
-
- /* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt on the
- * controller, since this requires the original irqstat value which
- * we won't easily be able to recreate later.
- */
-
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base are preserved.. */
-
- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #29
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm
--- 0001/arch/arm/mach-msm/include/mach/entry-macro-qgic.S
+++ work/arch/arm/mach-msm/include/mach/entry-macro-qgic.S 2010-11-10 15:27:06.000000000 +0900
@@ -9,7 +9,7 @@
*/
#include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
.macro disable_fiq
.endm
@@ -21,68 +21,3 @@
.macro arch_ret_to_user, tmp1, tmp2
.endm
-
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Migrated the code from ARM MP port to be more consistant
- * with interrupt processing , the following still holds true
- * however, all interrupts are treated the same regardless of
- * if they are local IPI or PPI
- *
- * Interrupts 0-15 are IPI
- * 16-31 are PPI
- * (16-18 are the timers)
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * A simple read from the controller will tell us the number of the
- * highest priority enabled interrupt. We then just need to check
- * whether it is in the valid range for an IRQ (0-1020 inclusive).
- *
- * Base ARM code assumes that the local (private) peripheral interrupts
- * are not valid, we treat them differently, in that the privates are
- * handled like normal shared interrupts with the exception that only
- * one processor can register the interrupt and the handler must be
- * the same for all processors.
- */
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 =srcCPU,
- 9-0 =int # */
-
- bic \irqnr, \irqstat, #0x1c00 @mask src
- cmp \irqnr, #15
- ldr \tmp, =1021
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
-
- .endm
-
- /* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt on the
- * controller, since this requires the original irqstat value which
- * we won't easily be able to recreate later.
- */
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base are preserved.. */
-
- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #16
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm
--- 0001/arch/arm/mach-realview/include/mach/entry-macro.S
+++ work/arch/arm/mach-realview/include/mach/entry-macro.S 2010-11-10 15:14:41.000000000 +0900
@@ -8,7 +8,7 @@
* warranty of any kind, whether express or implied.
*/
#include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
.macro disable_fiq
.endm
@@ -21,61 +21,3 @@
.macro arch_ret_to_user, tmp1, tmp2
.endm
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an interrupt if it's
- * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs.
- *
- * A simple read from the controller will tell us the number of the highest
- * priority enabled interrupt. We then just need to check whether it is in the
- * valid range for an IRQ (30-1020 inclusive).
- */
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
-
- ldr \tmp, =1021
-
- bic \irqnr, \irqstat, #0x1c00
-
- cmp \irqnr, #29
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
-
- .endm
-
- /* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt on the
- * controller, since this requires the original irqstat value which
- * we won't easily be able to recreate later.
- */
-
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base are preserved.. */
-
- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #29
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm
--- 0001/arch/arm/mach-tegra/include/mach/entry-macro.S
+++ work/arch/arm/mach-tegra/include/mach/entry-macro.S 2010-11-10 15:28:39.000000000 +0900
@@ -17,7 +17,7 @@
#if defined(CONFIG_ARM_GIC)
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
/* Uses the GIC interrupt controller built into the cpu */
#define ICTRL_BASE (IO_CPU_VIRT + 0x100)
@@ -32,68 +32,6 @@
.macro arch_ret_to_user, tmp1, tmp2
.endm
-
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an interrupt
- * if it's between 30 and 1020. The test_for_ipi routine below will
- * pick up on IPIs.
- *
- * A simple read from the controller will tell us the number of the
- * highest priority enabled interrupt. We then just need to check
- * whether it is in the valid range for an IRQ (30-1020 inclusive).
- */
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- /* bits 12-10 = src CPU, 9-0 = int # */
- ldr \irqstat, [\base, #GIC_CPU_INTACK]
-
- ldr \tmp, =1021
-
- bic \irqnr, \irqstat, #0x1c00
-
- cmp \irqnr, #29
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
-
- .endm
-
- /* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt on the
- * controller, since this requires the original irqstat value which
- * we won't easily be able to recreate later.
- */
-
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base are preserved.. */
-
- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #29
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm
-
#else
/* legacy interrupt controller for AP16 */
.macro disable_fiq
--- 0001/arch/arm/mach-ux500/include/mach/entry-macro.S
+++ work/arch/arm/mach-ux500/include/mach/entry-macro.S 2010-11-10 15:23:50.000000000 +0900
@@ -11,7 +11,7 @@
* warranty of any kind, whether express or implied.
*/
#include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
.macro disable_fiq
.endm
@@ -22,68 +22,3 @@
.macro arch_ret_to_user, tmp1, tmp2
.endm
-
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an
- * interrupt if it's between 30 and 1020. The test_for_ipi
- * routine below will pick up on IPIs.
- *
- * A simple read from the controller will tell us the number
- * of the highest priority enabled interrupt. We then just
- * need to check whether it is in the valid range for an
- * IRQ (30-1020 inclusive).
- */
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- /* bits 12-10 = src CPU, 9-0 = int # */
- ldr \irqstat, [\base, #GIC_CPU_INTACK]
-
- ldr \tmp, =1021
-
- bic \irqnr, \irqstat, #0x1c00
-
- cmp \irqnr, #29
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
-
- .endm
-
- /* We assume that irqstat (the raw value of the IRQ
- * acknowledge register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of
- * interrupt on the controller, since this requires the
- * original irqstat value which we won't easily be able
- * to recreate later.
- */
-
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base
- * are preserved..
- */
-
- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #29
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm
--- 0001/arch/arm/mach-vexpress/include/mach/entry-macro.S
+++ work/arch/arm/mach-vexpress/include/mach/entry-macro.S 2010-11-10 15:22:09.000000000 +0900
@@ -1,4 +1,4 @@
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>
.macro disable_fiq
.endm
@@ -10,58 +10,3 @@
.macro arch_ret_to_user, tmp1, tmp2
.endm
-
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an interrupt if it's
- * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs.
- *
- * A simple read from the controller will tell us the number of the highest
- * priority enabled interrupt. We then just need to check whether it is in the
- * valid range for an IRQ (30-1020 inclusive).
- */
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */
- ldr \tmp, =1021
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #29
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
- .endm
-
- /* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt on the
- * controller, since this requires the original irqstat value which
- * we won't easily be able to recreate later.
- */
-
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base are preserved.. */
-
- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #29
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm
-
next reply other threads:[~2010-11-10 7:00 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-11-10 7:00 Magnus Damm [this message]
2010-11-10 7:16 ` [PATCH] ARM: Common GIC entry macro code Shilimkar, Santosh
2010-11-10 7:35 ` Magnus Damm
2010-11-10 7:47 ` Srinidhi Kasagar
2010-11-10 20:28 ` Abhijeet Dharmapurikar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20101110070043.18735.53764.sendpatchset@t400s \
--to=magnus.damm@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.