From mboxrd@z Thu Jan 1 00:00:00 1970 From: Guenter Roeck Date: Fri, 10 Dec 2010 15:23:13 +0000 Subject: Re: [lm-sensors] weird lectures Message-Id: <20101210152313.GC11777@ericsson.com> List-Id: References: In-Reply-To: MIME-Version: 1.0 Content-Type: text/plain; charset="iso-8859-1" Content-Transfer-Encoding: quoted-printable To: lm-sensors@vger.kernel.org On Fri, Dec 10, 2010 at 09:32:47AM -0500, Jose M. Caballero wrote: > El jue, 09-12-2010 a las 08:20 -0800, Guenter Roeck escribi=F3: > > On Thu, Dec 09, 2010 at 11:09:34AM -0500, Jos=E9 M. Caballero wrote: > > [ ... ] > > >=20 > > > Thanks a lot. Finally it works. > > > But it is very worrying lectures: > > >=20 > > >=20 > > > w83667hg-isa-0290 > > > Adapter: ISA adapter > > > in0: +0.89 V (min =3D +0.00 V, max =3D +1.74 V) =20 > > > in1: +1.86 V (min =3D +0.73 V, max =3D +1.97 V) =20 > > > in2: +3.42 V (min =3D +0.45 V, max =3D +3.82 V) =20 > > > in3: +3.42 V (min =3D +1.18 V, max =3D +0.27 V) ALARM > > > in4: +0.05 V (min =3D +0.50 V, max =3D +0.11 V) ALARM > > > in5: +1.74 V (min =3D +1.39 V, max =3D +0.91 V) ALARM > > > in7: +3.44 V (min =3D +0.90 V, max =3D +3.07 V) ALARM > > > in8: +3.30 V (min =3D +1.31 V, max =3D +1.76 V) ALARM > > > fan1: 0 RPM (min =3D 340 RPM, div =3D 128) ALARM > > > fan2: 2008 RPM (min =3D 448 RPM, div =3D 32) > > > fan3: 0 RPM (min =3D 405 RPM, div =3D 128) ALARM > > > temp1: +30.0=B0C (high =3D -10.0=B0C, hyst =3D -5.0=B0C) ALA= RM sensor > > > thermistor > > > temp2: +32.0=B0C (high =3D +80.0=B0C, hyst =3D +75.0=B0C) sen= sor > > > thermistor > > > temp3: +127.5=B0C (high =3D +80.0=B0C, hyst =3D +75.0=B0C) ALA= RM sensor > > > thermistor > > > cpu0_vid: +2.500 V > > >=20 > > > I hope the sensor doesn't work properly... > > >=20 > > temp3 is probably not connected, as is fan1 and fan3. The temp1 high li= mit seems to be=20 > > unset. The voltage limits look odd, with max being lower than min in so= me cases. > > Since ALARM is set for those voltages, I suspect that the limits are no= t set correctly. > > You can test that by setting more reasonable limits for one of the volt= ages (and temp1) > > and verify if that resets the ALARM bit. > >=20 > > Guenter > >=20 >=20 > After installing (successfully) lm-sensors and the standalone patch for > Nuvoton w83627hg-b (w83627ehf driver), I have not a /etc/sensors.conf > file just a sensors3.conf file with next relevant data: > =20 > chip "w83627ehf-*" "w83627dhg-*" > =20 > label in0 "Vcore" > label in2 "AVCC" > label in3 "VCC" > label in7 "3VSB" > label in8 "Vbat" > =20 > set in2_min 3.3 * 0.90 > set in2_max 3.3 * 1.10 > set in3_min 3.3 * 0.90 > set in3_max 3.3 * 1.10 > set in7_min 3.3 * 0.90 > set in7_max 3.3 * 1.10 > set in8_min 3.0 * 0.90 > set in8_max 3.0 * 1.10 > =20 > (The same data as the sensors.conf.default from the > lm_sensors-3.2.0.tar.bz2) > =20 > Could be due to that some of my amazing readings of 'sensors'? How to > fix it? >=20 Might well be. I would suggest to remove the set lines (or comment them out= ) and=20 restart your system. Guenter _______________________________________________ lm-sensors mailing list lm-sensors@lm-sensors.org http://lists.lm-sensors.org/mailman/listinfo/lm-sensors