From: Anton Blanchard <anton@samba.org>
To: leitao@linux.vnet.ibm.com
Cc: netdev@vger.kernel.org, michael@ellerman.id.au
Subject: [PATCH 8/14] ehea: Simplify ehea_xmit2 and ehea_xmit3
Date: Tue, 5 Apr 2011 21:39:09 +1000 [thread overview]
Message-ID: <20110405213909.31602f45@kryten> (raw)
In-Reply-To: <20110405212825.6eb85677@kryten>
Based on a patch from Michael Ellerman, clean up a significant
portion of the transmit path. There was a lot of duplication here.
Even worse, we were always checksumming tx packets and ignoring the
skb->ip_summed field.
Also remove NETIF_F_FRAGLIST from dev->features, I'm not sure why
it was enabled.
Signed-off-by: Anton Blanchard <anton@samba.org>
---
Index: linux-2.6/drivers/net/ehea/ehea_main.c
===================================================================
--- linux-2.6.orig/drivers/net/ehea/ehea_main.c 2011-04-05 20:36:34.437226735 +1000
+++ linux-2.6/drivers/net/ehea/ehea_main.c 2011-04-05 20:36:38.726736977 +1000
@@ -1681,37 +1681,6 @@ static int ehea_clean_portres(struct ehe
return ret;
}
-/*
- * The write_* functions store information in swqe which is used by
- * the hardware to calculate the ip/tcp/udp checksum
- */
-
-static inline void write_ip_start_end(struct ehea_swqe *swqe,
- const struct sk_buff *skb)
-{
- swqe->ip_start = skb_network_offset(skb);
- swqe->ip_end = (u8)(swqe->ip_start + ip_hdrlen(skb) - 1);
-}
-
-static inline void write_tcp_offset_end(struct ehea_swqe *swqe,
- const struct sk_buff *skb)
-{
- swqe->tcp_offset =
- (u8)(swqe->ip_end + 1 + offsetof(struct tcphdr, check));
-
- swqe->tcp_end = (u16)skb->len - 1;
-}
-
-static inline void write_udp_offset_end(struct ehea_swqe *swqe,
- const struct sk_buff *skb)
-{
- swqe->tcp_offset =
- (u8)(swqe->ip_end + 1 + offsetof(struct udphdr, check));
-
- swqe->tcp_end = (u16)skb->len - 1;
-}
-
-
static void write_swqe2_TSO(struct sk_buff *skb,
struct ehea_swqe *swqe, u32 lkey)
{
@@ -2113,41 +2082,46 @@ static int ehea_change_mtu(struct net_de
return 0;
}
-static void ehea_xmit2(struct sk_buff *skb, struct net_device *dev,
- struct ehea_swqe *swqe, u32 lkey)
+static void xmit_common(struct sk_buff *skb, struct ehea_swqe *swqe)
{
- if (skb->protocol == htons(ETH_P_IP)) {
- const struct iphdr *iph = ip_hdr(skb);
+ swqe->tx_control |= EHEA_SWQE_IMM_DATA_PRESENT | EHEA_SWQE_CRC;
- /* IPv4 */
- swqe->tx_control |= EHEA_SWQE_CRC
- | EHEA_SWQE_IP_CHECKSUM
- | EHEA_SWQE_TCP_CHECKSUM
- | EHEA_SWQE_IMM_DATA_PRESENT
- | EHEA_SWQE_DESCRIPTORS_PRESENT;
-
- write_ip_start_end(swqe, skb);
-
- if (iph->protocol == IPPROTO_UDP) {
- if ((iph->frag_off & IP_MF) ||
- (iph->frag_off & IP_OFFSET))
- /* IP fragment, so don't change cs */
- swqe->tx_control &= ~EHEA_SWQE_TCP_CHECKSUM;
- else
- write_udp_offset_end(swqe, skb);
- } else if (iph->protocol == IPPROTO_TCP) {
- write_tcp_offset_end(swqe, skb);
- }
+ if (skb->protocol != htons(ETH_P_IP))
+ return;
- /* icmp (big data) and ip segmentation packets (all other ip
- packets) do not require any special handling */
+ if (skb->ip_summed == CHECKSUM_PARTIAL)
+ swqe->tx_control |= EHEA_SWQE_IP_CHECKSUM;
- } else {
- /* Other Ethernet Protocol */
- swqe->tx_control |= EHEA_SWQE_CRC
- | EHEA_SWQE_IMM_DATA_PRESENT
- | EHEA_SWQE_DESCRIPTORS_PRESENT;
+ swqe->ip_start = skb_network_offset(skb);
+ swqe->ip_end = swqe->ip_start + ip_hdrlen(skb) - 1;
+
+ switch (ip_hdr(skb)->protocol) {
+ case IPPROTO_UDP:
+ if (skb->ip_summed == CHECKSUM_PARTIAL)
+ swqe->tx_control |= EHEA_SWQE_TCP_CHECKSUM;
+
+ swqe->tcp_offset = swqe->ip_end + 1 +
+ offsetof(struct udphdr, check);
+ swqe->tcp_end = skb->len - 1;
+ break;
+
+ case IPPROTO_TCP:
+ if (skb->ip_summed == CHECKSUM_PARTIAL)
+ swqe->tx_control |= EHEA_SWQE_TCP_CHECKSUM;
+
+ swqe->tcp_offset = swqe->ip_end + 1 +
+ offsetof(struct tcphdr, check);
+ swqe->tcp_end = skb->len - 1;
+ break;
}
+}
+
+static void ehea_xmit2(struct sk_buff *skb, struct net_device *dev,
+ struct ehea_swqe *swqe, u32 lkey)
+{
+ swqe->tx_control |= EHEA_SWQE_DESCRIPTORS_PRESENT;
+
+ xmit_common(skb, swqe);
write_swqe2_data(skb, dev, swqe, lkey);
}
@@ -2160,51 +2134,11 @@ static void ehea_xmit3(struct sk_buff *s
skb_frag_t *frag;
int i;
- if (skb->protocol == htons(ETH_P_IP)) {
- const struct iphdr *iph = ip_hdr(skb);
-
- /* IPv4 */
- write_ip_start_end(swqe, skb);
+ xmit_common(skb, swqe);
- if (iph->protocol == IPPROTO_TCP) {
- swqe->tx_control |= EHEA_SWQE_CRC
- | EHEA_SWQE_IP_CHECKSUM
- | EHEA_SWQE_TCP_CHECKSUM
- | EHEA_SWQE_IMM_DATA_PRESENT;
-
- write_tcp_offset_end(swqe, skb);
-
- } else if (iph->protocol == IPPROTO_UDP) {
- if ((iph->frag_off & IP_MF) ||
- (iph->frag_off & IP_OFFSET))
- /* IP fragment, so don't change cs */
- swqe->tx_control |= EHEA_SWQE_CRC
- | EHEA_SWQE_IMM_DATA_PRESENT;
- else {
- swqe->tx_control |= EHEA_SWQE_CRC
- | EHEA_SWQE_IP_CHECKSUM
- | EHEA_SWQE_TCP_CHECKSUM
- | EHEA_SWQE_IMM_DATA_PRESENT;
-
- write_udp_offset_end(swqe, skb);
- }
- } else {
- /* icmp (big data) and
- ip segmentation packets (all other ip packets) */
- swqe->tx_control |= EHEA_SWQE_CRC
- | EHEA_SWQE_IP_CHECKSUM
- | EHEA_SWQE_IMM_DATA_PRESENT;
- }
- } else {
- /* Other Ethernet Protocol */
- swqe->tx_control |= EHEA_SWQE_CRC | EHEA_SWQE_IMM_DATA_PRESENT;
- }
- /* copy (immediate) data */
if (nfrags == 0) {
- /* data is in a single piece */
skb_copy_from_linear_data(skb, imm_data, skb->len);
} else {
- /* first copy data from the skb->data buffer ... */
skb_copy_from_linear_data(skb, imm_data,
skb_headlen(skb));
imm_data += skb_headlen(skb);
@@ -2218,6 +2152,7 @@ static void ehea_xmit3(struct sk_buff *s
imm_data += frag->size;
}
}
+
swqe->immediate_data_length = skb->len;
dev_kfree_skb(skb);
}
@@ -3221,7 +3156,7 @@ struct ehea_port *ehea_setup_single_port
dev->netdev_ops = &ehea_netdev_ops;
ehea_set_ethtool_ops(dev);
- dev->features = NETIF_F_SG | NETIF_F_FRAGLIST | NETIF_F_TSO
+ dev->features = NETIF_F_SG | NETIF_F_TSO
| NETIF_F_HIGHDMA | NETIF_F_IP_CSUM | NETIF_F_HW_VLAN_TX
| NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER;
dev->vlan_features = NETIF_F_SG | NETIF_F_TSO | NETIF_F_HIGHDMA |
next prev parent reply other threads:[~2011-04-05 11:39 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-04-05 11:28 [PATCH 1/14] ehea: Remove NETIF_F_LLTX Anton Blanchard
2011-04-05 11:29 ` [PATCH 2/14] ehea: Update multiqueue support Anton Blanchard
2011-04-11 1:13 ` Michael Ellerman
2011-04-05 11:30 ` [PATCH 3/14] ehea: Remove force_irq logic in napi poll routine Anton Blanchard
2011-04-05 11:32 ` [PATCH 4/14] ehea: Remove num_tx_qps module option Anton Blanchard
2011-04-05 11:33 ` [PATCH 5/14] ehea: Don't check NETIF_F_TSO in TX path Anton Blanchard
2011-04-05 11:35 ` [PATCH 6/14] ehea: Add vlan_features Anton Blanchard
2011-04-05 11:36 ` [PATCH 7/14] ehea: Allocate large enough skbs to avoid partial cacheline DMA writes Anton Blanchard
2011-04-05 11:39 ` Anton Blanchard [this message]
2011-04-05 11:40 ` [PATCH 9/14] ehea: Merge swqe2 TSO and non TSO paths Anton Blanchard
2011-04-05 11:41 ` [PATCH 10/14] ehea: Simplify type 3 transmit routine Anton Blanchard
2011-04-05 11:41 ` [PATCH 11/14] ehea: Remove some unused definitions Anton Blanchard
2011-04-05 11:42 ` [PATCH 12/14] ehea: Add some more ethtool operations and 64bit stats Anton Blanchard
2011-04-05 13:07 ` Ben Hutchings
2011-04-05 21:35 ` Anton Blanchard
2011-04-05 11:43 ` [PATCH 13/14] ehea: Remove LRO support Anton Blanchard
2011-04-05 11:45 ` [PATCH 14/14] ehea: Add GRO support Anton Blanchard
2011-04-05 21:29 ` Jesse Gross
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110405213909.31602f45@kryten \
--to=anton@samba.org \
--cc=leitao@linux.vnet.ibm.com \
--cc=michael@ellerman.id.au \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.