From: Alexis Berlemont <alexis.berlemont@domain.hid>
To: luxInteg <lux-integ@domain.hid>
Cc: xenomai@xenomai.org
Subject: Re: [Xenomai-help] analogy on 9812/9112 daq cards
Date: Mon, 16 May 2011 23:28:42 +0200 [thread overview]
Message-ID: <20110516212842.GA2805@domain.hid> (raw)
In-Reply-To: <201105011546.01925.lux-integ@domain.hid>
Hi,
Sorry for the late answer, your mail was not big enough to prevent me
from badly handling it :) If it happens again, do not hesitate to
insult me (privately or not).
luxInteg wrote:
> On Thursday 21 October 2010 07:24:04 Alexis Berlemont wrote:
> > Hi,
> >
> > On Wed, Oct 20, 2010 at 11:46 PM, luxInteg <lux-integ@domain.hid> wrote:
> > > Greetings,
> > >
> > > I had a cursory non-expert look at analogy and noticed the supported
> > > cards are all by NI. I want to dabble a little with with xenomai and
> > > as a starter with these two daq-cards:-
> > >
> > >
> > > http://www.adlinktech.com/PD/web/PD_detail.php?sg-daq&pid=29
> > >
> > > and
> > >
> > > http://www.adlinktech.com/PD/web/PD_detail.php?pid=566
> > >
> > > (both have the amcc5933 PCI intrface)
> > >
> > > is there a template with the needed subroutines ( or functions )
> > > necessary have a go at writing a driver for analogy
> > > for devices of the above types?
> >
> > A good start would be to have a look at the driver "analogy_fake"
> > which is just a test driver. Concerning the API for driver
> > development, it is described in the Doxygen doc (Modules -> Analogy
> > API -> Driver API -> *) at:
> > http://www.xenomai.org/documentation/xenomai-2.5/html/api/index.html
> >
>
> Thanks for your advice
>
> I have decided to take the plunge and ATTEMPT porting the comedi driver for
> pci-9118 over to analogy. ( I stress attempt ). The comedi driver is
> attached.
>
> I have scanned through the analogy api and the fake.c driver as suggested.
> But I am unsure how to work up functions that avoid the use of comedi header
> files uch as:-
>
> #include "comedi_fc.h"
> #include "comedi_pci.h"
> #include <linux/comedidev.h>
>
> I checked the the two files mite.c (for analogy) and mite.c ( for comedi) {
> both also attached }
> the former has none of the definitions above whilst the latter does.
> I would thus be grateful for some guidance of how calls to comedi_fc.h,
> comedi_pci.h, and linux/comedidev.h are 'written out' in a transfer of a
> driver such as pci-9118.c from comedi to analogy.
In the source code of an analogy driver, only one analogy related
header should be present:
#include <analogy/analogy_driver.h>
Even if the APIs look similar in many ways, analogy was rewritten
from scratch. So, it will be difficult for you to find similarities in
the headers or in the core sources.
So, if you want to find your way in the Analogy code, the Doxygen
documentation should be interesting. Did you have a look at it? If you
did not find it clear enough, do not hesitate to tell it and/or make
proposals to enrich it.
http://www.xenomai.org/documentation/xenomai-2.5/html/api/index.html
Go to "Modules -> Analogy API-> Driver API" and have a look at the
pages theres. The first pages to read should be "Driver management
services" and "Buffer management services"; this documentation + the
pattern of the fake driver should help you.
I did not understand what you want me to do with the
attachments. Did you change anything?
>
> Thanks in advance.
>
> sincerely
> luxInteg.
>
> ========
>
> ps sorry for the big attachments, I thought of using URLs to the said files
> but found them in git repositories and thus too
> too long and breakable.
> /**
> * @file
> * Hardware driver for NI Mite PCI interface chip
> *
> * Copyright (C) 1999 David A. Schleef <ds@domain.hid>
> *
> * This code is free software; you can redistribute it and/or modify
> * it under the terms of the GNU General Public License as published
> * by the Free Software Foundation; either version 2 of the License,
> * or (at your option) any later version.
> *
> * This code is distributed in the hope that it will be useful, but
> * WITHOUT ANY WARRANTY; without even the implied warranty of
> * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
> * General Public License for more details.
> *
> * You should have received a copy of the GNU General Public License
> * along with Xenomai; if not, write to the Free Software Foundation,
> * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
> *
> * The NI Mite driver was originally written by Tomasz Motylewski
> * <...>, and ported to comedi by ds.
> *
> * References for specifications:
> *
> * 321747b.pdf Register Level Programmer Manual (obsolete)
> * 321747c.pdf Register Level Programmer Manual (new)
> * DAQ-STC reference manual
> *
> * Other possibly relevant info:
> *
> * 320517c.pdf User manual (obsolete)
> * 320517f.pdf User manual (new)
> * 320889a.pdf delete
> * 320906c.pdf maximum signal ratings
> * 321066a.pdf about 16x
> * 321791a.pdf discontinuation of at-mio-16e-10 rev. c
> * 321808a.pdf about at-mio-16e-10 rev P
> * 321837a.pdf discontinuation of at-mio-16de-10 rev d
> * 321838a.pdf about at-mio-16de-10 rev N
> *
> * ISSUES:
> */
>
> #include <asm/system.h>
>
> #include "mite.h"
>
> #ifdef CONFIG_DEBUG_MITE
> #define MDPRINTK(fmt, args...) rtdm_printk(fmt, ##args)
> #else /* !CONFIG_DEBUG_MITE */
> #define MDPRINTK(fmt, args...)
> #endif /* CONFIG_DEBUG_MITE */
>
> static LIST_HEAD(mite_devices);
>
> static struct pci_device_id mite_id[] = {
> {PCI_DEVICE(PCI_VENDOR_ID_NATINST, PCI_ANY_ID), },
> {0, }
> };
>
> static int mite_probe(struct pci_dev *dev, const struct pci_device_id *id)
> {
> int i;
> struct mite_struct *mite;
>
> mite = kmalloc(sizeof(struct mite_struct), GFP_KERNEL);
> if(mite == NULL)
> return -ENOMEM;
>
> memset(mite, 0, sizeof(struct mite_struct));
>
> a4l_lock_init(&mite->lock);
> mite->pcidev = dev;
>
> for(i = 0; i < MAX_MITE_DMA_CHANNELS; i++) {
> mite->channels[i].mite = mite;
> mite->channels[i].channel = i;
> mite->channels[i].done = 1;
> }
>
> list_add(&mite->list, &mite_devices);
>
> return 0;
> }
>
> static void mite_remove(struct pci_dev *dev)
> {
> struct list_head *this;
>
> list_for_each(this, &mite_devices) {
> struct mite_struct *mite =
> list_entry(this, struct mite_struct, list);
>
> if(mite->pcidev == dev) {
> list_del(this);
> kfree(mite);
> break;
> }
> }
> }
>
> static struct pci_driver mite_driver = {
> .name = "mite",
> .id_table = mite_id,
> .probe = mite_probe,
> .remove = mite_remove,
> };
>
> int mite_setup(struct mite_struct *mite, int use_iodwbsr_1)
> {
> unsigned long length;
> resource_size_t addr;
> int i;
> u32 csigr_bits;
> unsigned unknown_dma_burst_bits;
>
> __a4l_dbg(1, drv_dbg, "mite: starting setup...\n");
>
> if(pci_enable_device(mite->pcidev)){
> __a4l_err("error enabling mite\n");
> return -EIO;
> }
>
> pci_set_master(mite->pcidev);
>
> if (pci_request_regions( mite->pcidev, "mite")) {
> __a4l_err("failed to request mite io regions\n");
> return -EIO;
> };
>
>
> /* The PCI BAR0 is the Mite */
> addr = pci_resource_start(mite->pcidev, 0);
> length = pci_resource_len(mite->pcidev, 0);
> mite->mite_phys_addr = addr;
> mite->mite_io_addr = ioremap(addr, length);
> if (!mite->mite_io_addr) {
> __a4l_err("failed to remap mite io memory address\n");
> return -ENOMEM;
> }
>
> __a4l_dbg(1, drv_dbg,
> "mite: bar0(mite) 0x%08llx mapped to %p\n",
> (unsigned long long)mite->mite_phys_addr,
> mite->mite_io_addr);
>
>
> /* The PCI BAR1 is the DAQ */
> addr = pci_resource_start(mite->pcidev, 1);
> length = pci_resource_len(mite->pcidev, 1);
> mite->daq_phys_addr = addr;
> mite->daq_io_addr = ioremap(mite->daq_phys_addr, length);
> if (!mite->daq_io_addr) {
> __a4l_err("failed to remap daq io memory address\n");
> return -ENOMEM;
> }
>
> __a4l_dbg(1, drv_dbg,
> "mite: bar0(daq) 0x%08llx mapped to %p\n",
> (unsigned long long)mite->daq_phys_addr,
> mite->daq_io_addr);
>
> if (use_iodwbsr_1) {
>
> __a4l_dbg(1, drv_dbg,
> "mite: using I/O Window Base Size register 1\n");
>
> writel(0, mite->mite_io_addr + MITE_IODWBSR);
> writel(mite->
> daq_phys_addr | WENAB |
> MITE_IODWBSR_1_WSIZE_bits(length),
> mite->mite_io_addr + MITE_IODWBSR_1);
> writel(0, mite->mite_io_addr + MITE_IODWCR_1);
> } else {
> writel(mite->daq_phys_addr | WENAB,
> mite->mite_io_addr + MITE_IODWBSR);
> }
>
> /* Make sure dma bursts work. I got this from running a bus analyzer
> on a pxi-6281 and a pxi-6713. 6713 powered up with register value
> of 0x61f and bursts worked. 6281 powered up with register value of
> 0x1f and bursts didn't work. The NI windows driver reads the register,
> then does a bitwise-or of 0x600 with it and writes it back.
> */
> unknown_dma_burst_bits =
> readl(mite->mite_io_addr + MITE_UNKNOWN_DMA_BURST_REG);
> unknown_dma_burst_bits |= UNKNOWN_DMA_BURST_ENABLE_BITS;
> writel(unknown_dma_burst_bits,
> mite->mite_io_addr + MITE_UNKNOWN_DMA_BURST_REG);
>
> csigr_bits = readl(mite->mite_io_addr + MITE_CSIGR);
> mite->num_channels = mite_csigr_dmac(csigr_bits);
> if (mite->num_channels > MAX_MITE_DMA_CHANNELS) {
> __a4l_err("MITE: bug? chip claims to have %i dma channels. "
> "Setting to %i.\n",
> mite->num_channels, MAX_MITE_DMA_CHANNELS);
> mite->num_channels = MAX_MITE_DMA_CHANNELS;
> }
>
> __a4l_dbg(1, drv_dbg,
> "mite: version = %i, type = %i, mite mode = %i, "
> "interface mode = %i\n",
> mite_csigr_version(csigr_bits),
> mite_csigr_type(csigr_bits),
> mite_csigr_mmode(csigr_bits),
> mite_csigr_imode(csigr_bits));
> __a4l_dbg(1, drv_dbg,
> "mite: num channels = %i, write post fifo depth = %i, "
> "wins = %i, iowins = %i\n",
> mite_csigr_dmac(csigr_bits),
> mite_csigr_wpdep(csigr_bits),
> mite_csigr_wins(csigr_bits),
> mite_csigr_iowins(csigr_bits));
>
> for (i = 0; i < mite->num_channels; i++) {
> /* Registers the channel as a free one */
> mite->channel_allocated[i] = 0;
> /* Reset the channel */
> writel(CHOR_DMARESET, mite->mite_io_addr + MITE_CHOR(i));
> /* Disable interrupts */
> writel(CHCR_CLR_DMA_IE | CHCR_CLR_LINKP_IE | CHCR_CLR_SAR_IE |
> CHCR_CLR_DONE_IE | CHCR_CLR_MRDY_IE | CHCR_CLR_DRDY_IE |
> CHCR_CLR_LC_IE | CHCR_CLR_CONT_RB_IE,
> mite->mite_io_addr + MITE_CHCR(i));
>
> __a4l_dbg(1, drv_dbg, "mite: channel[%d] initialized\n", i);
> }
>
> mite->used = 1;
>
> return 0;
> }
>
> void mite_unsetup(struct mite_struct *mite)
> {
> if (!mite)
> return;
>
> if (mite->mite_io_addr) {
> iounmap(mite->mite_io_addr);
> mite->mite_io_addr = NULL;
> }
>
> if (mite->daq_io_addr) {
> iounmap(mite->daq_io_addr);
> mite->daq_io_addr = NULL;
> }
>
> if(mite->used)
> pci_release_regions( mite->pcidev );
>
> mite->used = 0;
> }
>
> void mite_list_devices(void)
> {
> struct list_head *this;
>
> printk("Analogy: MITE: Available NI device IDs:");
> list_for_each(this, &mite_devices) {
> struct mite_struct *mite =
> list_entry(this, struct mite_struct, list);
>
> printk(" 0x%04x", mite_device_id(mite));
> if(mite->used)
> printk("(used)");
> }
>
> printk("\n");
> }
>
>
>
> struct mite_struct * mite_find_device(int bus, int slot, unsigned short device_id)
> {
> struct list_head *this;
>
> list_for_each(this, &mite_devices) {
> struct mite_struct *mite =
> list_entry(this, struct mite_struct, list);
>
> if(mite->pcidev->device != device_id)
> continue;
>
> if((bus <= 0 && slot <= 0) ||
> (bus == mite->pcidev->bus->number &&
> slot == PCI_SLOT(mite->pcidev->devfn)))
> return mite;
> }
>
> return NULL;
> }
> EXPORT_SYMBOL_GPL(mite_find_device);
>
> struct mite_channel *mite_request_channel_in_range(struct mite_struct *mite,
> struct mite_dma_descriptor_ring *ring,
> unsigned min_channel,
> unsigned max_channel)
> {
> int i;
> unsigned long flags;
> struct mite_channel *channel = NULL;
>
> __a4l_dbg(1, drv_dbg,
> "mite: mite_request_channel_in_range: "
> "min_channel = %u, max_channel = %u\n",
> min_channel, max_channel);
>
> /* spin lock so mite_release_channel can be called safely from interrupts */
> a4l_lock_irqsave(&mite->lock, flags);
> for (i = min_channel; i <= max_channel; ++i) {
>
> __a4l_dbg(1, drv_dbg,
> "mite: mite_request_channel_in_range: "
> "channel[%d] allocated = %d\n",
> i, mite->channel_allocated[i]);
>
> if (mite->channel_allocated[i] == 0) {
> mite->channel_allocated[i] = 1;
> channel = &mite->channels[i];
> channel->ring = ring;
> break;
> }
> }
> a4l_unlock_irqrestore(&mite->lock, flags);
> return channel;
> }
>
> void mite_release_channel(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> unsigned long flags;
>
> /* Spin lock to prevent races with mite_request_channel */
> a4l_lock_irqsave(&mite->lock, flags);
> if (mite->channel_allocated[mite_chan->channel]) {
> /* disable all channel's interrupts */
> writel(CHCR_CLR_DMA_IE | CHCR_CLR_LINKP_IE |
> CHCR_CLR_SAR_IE | CHCR_CLR_DONE_IE |
> CHCR_CLR_MRDY_IE | CHCR_CLR_DRDY_IE |
> CHCR_CLR_LC_IE | CHCR_CLR_CONT_RB_IE,
> mite->mite_io_addr + MITE_CHCR(mite_chan->channel));
> mite_dma_disarm(mite_chan);
> mite_dma_reset(mite_chan);
> mite->channel_allocated[mite_chan->channel] = 0;
> mite_chan->ring = NULL;
> mmiowb();
> }
> a4l_unlock_irqrestore(&mite->lock, flags);
> }
>
> void mite_dma_arm(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> int chor;
> unsigned long flags;
>
> MDPRINTK("mite_dma_arm ch%i\n", mite_chan->channel);
> /* Memory barrier is intended to insure any twiddling with the buffer
> is done before writing to the mite to arm dma transfer */
> smp_mb();
> /* arm */
> chor = CHOR_START;
> a4l_lock_irqsave(&mite->lock, flags);
> mite_chan->done = 0;
> writel(chor, mite->mite_io_addr + MITE_CHOR(mite_chan->channel));
> mmiowb();
> a4l_unlock_irqrestore(&mite->lock, flags);
> }
>
> void mite_dma_disarm(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> unsigned chor;
>
> /* disarm */
> chor = CHOR_ABORT;
> writel(chor, mite->mite_io_addr + MITE_CHOR(mite_chan->channel));
> }
>
> int mite_buf_change(struct mite_dma_descriptor_ring *ring, a4l_subd_t *subd)
> {
> a4l_buf_t *buf = subd->buf;
> unsigned int n_links;
> int i;
>
> if (ring->descriptors) {
> pci_free_consistent(ring->pcidev,
> ring->n_links * sizeof(struct mite_dma_descriptor),
> ring->descriptors, ring->descriptors_dma_addr);
> }
> ring->descriptors = NULL;
> ring->descriptors_dma_addr = 0;
> ring->n_links = 0;
>
> if (buf->size == 0) {
> return 0;
> }
> n_links = buf->size >> PAGE_SHIFT;
>
> MDPRINTK("ring->pcidev=%p, n_links=0x%04x\n", ring->pcidev, n_links);
>
> ring->descriptors =
> pci_alloc_consistent(ring->pcidev,
> n_links * sizeof(struct mite_dma_descriptor),
> &ring->descriptors_dma_addr);
> if (!ring->descriptors) {
> printk("MITE: ring buffer allocation failed\n");
> return -ENOMEM;
> }
> ring->n_links = n_links;
>
> for (i = 0; i < n_links; i++) {
> ring->descriptors[i].count = cpu_to_le32(PAGE_SIZE);
> ring->descriptors[i].addr = cpu_to_le32(buf->pg_list[i]);
> ring->descriptors[i].next =
> cpu_to_le32(ring->descriptors_dma_addr +
> (i + 1) * sizeof(struct mite_dma_descriptor));
> }
>
> ring->descriptors[n_links - 1].next =
> cpu_to_le32(ring->descriptors_dma_addr);
>
> /* Barrier is meant to insure that all the writes to the dma descriptors
> have completed before the dma controller is commanded to read them */
> smp_wmb();
>
> return 0;
> }
>
> void mite_prep_dma(struct mite_channel *mite_chan,
> unsigned int num_device_bits, unsigned int num_memory_bits)
> {
> unsigned int chor, chcr, mcr, dcr, lkcr;
> struct mite_struct *mite = mite_chan->mite;
>
> MDPRINTK("mite_prep_dma ch%i\n", mite_chan->channel);
>
> /* reset DMA and FIFO */
> chor = CHOR_DMARESET | CHOR_FRESET;
> writel(chor, mite->mite_io_addr + MITE_CHOR(mite_chan->channel));
>
> /* short link chaining mode */
> chcr = CHCR_SET_DMA_IE | CHCR_LINKSHORT | CHCR_SET_DONE_IE |
> CHCR_BURSTEN;
> /*
> * Link Complete Interrupt: interrupt every time a link
> * in MITE_RING is completed. This can generate a lot of
> * extra interrupts, but right now we update the values
> * of buf_int_ptr and buf_int_count at each interrupt. A
> * better method is to poll the MITE before each user
> * "read()" to calculate the number of bytes available.
> */
> chcr |= CHCR_SET_LC_IE;
> if (num_memory_bits == 32 && num_device_bits == 16) {
> /* Doing a combined 32 and 16 bit byteswap gets the 16
> bit samples into the fifo in the right order.
> Tested doing 32 bit memory to 16 bit device
> transfers to the analog out of a pxi-6281, which
> has mite version = 1, type = 4. This also works
> for dma reads from the counters on e-series boards.
> */
> chcr |= CHCR_BYTE_SWAP_DEVICE | CHCR_BYTE_SWAP_MEMORY;
> }
>
> if (mite_chan->dir == A4L_INPUT) {
> chcr |= CHCR_DEV_TO_MEM;
> }
> writel(chcr, mite->mite_io_addr + MITE_CHCR(mite_chan->channel));
>
> /* to/from memory */
> mcr = CR_RL(64) | CR_ASEQUP;
> switch (num_memory_bits) {
> case 8:
> mcr |= CR_PSIZE8;
> break;
> case 16:
> mcr |= CR_PSIZE16;
> break;
> case 32:
> mcr |= CR_PSIZE32;
> break;
> default:
> __a4l_err("MITE: bug! "
> "invalid mem bit width for dma transfer\n");
> break;
> }
> writel(mcr, mite->mite_io_addr + MITE_MCR(mite_chan->channel));
>
> /* from/to device */
> dcr = CR_RL(64) | CR_ASEQUP;
> dcr |= CR_PORTIO | CR_AMDEVICE | CR_REQSDRQ(mite_chan->channel);
> switch (num_device_bits) {
> case 8:
> dcr |= CR_PSIZE8;
> break;
> case 16:
> dcr |= CR_PSIZE16;
> break;
> case 32:
> dcr |= CR_PSIZE32;
> break;
> default:
> __a4l_info("MITE: bug! "
> "invalid dev bit width for dma transfer\n");
> break;
> }
> writel(dcr, mite->mite_io_addr + MITE_DCR(mite_chan->channel));
>
> /* reset the DAR */
> writel(0, mite->mite_io_addr + MITE_DAR(mite_chan->channel));
>
> /* the link is 32bits */
> lkcr = CR_RL(64) | CR_ASEQUP | CR_PSIZE32;
> writel(lkcr, mite->mite_io_addr + MITE_LKCR(mite_chan->channel));
>
> /* starting address for link chaining */
> writel(mite_chan->ring->descriptors_dma_addr,
> mite->mite_io_addr + MITE_LKAR(mite_chan->channel));
>
> MDPRINTK("exit mite_prep_dma\n");
> }
>
> u32 mite_device_bytes_transferred(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> return readl(mite->mite_io_addr + MITE_DAR(mite_chan->channel));
> }
>
> u32 mite_bytes_in_transit(struct mite_channel * mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> return readl(mite->mite_io_addr +
> MITE_FCR(mite_chan->channel)) & 0x000000FF;
> }
>
> /* Returns lower bound for number of bytes transferred from device to memory */
> u32 mite_bytes_written_to_memory_lb(struct mite_channel * mite_chan)
> {
> u32 device_byte_count;
>
> device_byte_count = mite_device_bytes_transferred(mite_chan);
> return device_byte_count - mite_bytes_in_transit(mite_chan);
> }
>
> /* Returns upper bound for number of bytes transferred from device to memory */
> u32 mite_bytes_written_to_memory_ub(struct mite_channel * mite_chan)
> {
> u32 in_transit_count;
>
> in_transit_count = mite_bytes_in_transit(mite_chan);
> return mite_device_bytes_transferred(mite_chan) - in_transit_count;
> }
>
> /* Returns lower bound for number of bytes read from memory for transfer to device */
> u32 mite_bytes_read_from_memory_lb(struct mite_channel * mite_chan)
> {
> u32 device_byte_count;
>
> device_byte_count = mite_device_bytes_transferred(mite_chan);
> return device_byte_count + mite_bytes_in_transit(mite_chan);
> }
>
> /* Returns upper bound for number of bytes read from memory for transfer to device */
> u32 mite_bytes_read_from_memory_ub(struct mite_channel * mite_chan)
> {
> u32 in_transit_count;
>
> in_transit_count = mite_bytes_in_transit(mite_chan);
> return mite_device_bytes_transferred(mite_chan) + in_transit_count;
> }
>
> int mite_sync_input_dma(struct mite_channel *mite_chan, a4l_subd_t *subd)
> {
> unsigned int nbytes_lb, nbytes_ub;
>
> nbytes_lb = mite_bytes_written_to_memory_lb(mite_chan);
> nbytes_ub = mite_bytes_written_to_memory_ub(mite_chan);
>
> if(a4l_buf_prepare_absput(subd, nbytes_ub) != 0) {
> __a4l_err("MITE: DMA overwrite of free area\n");
> return -EPIPE;
> }
>
> return a4l_buf_commit_absput(subd, nbytes_lb);
> }
>
> int mite_sync_output_dma(struct mite_channel *mite_chan, a4l_subd_t *subd)
> {
> a4l_buf_t *buf = subd->buf;
> unsigned int nbytes_ub, nbytes_lb;
> int err;
>
> nbytes_lb = mite_bytes_read_from_memory_lb(mite_chan);
> nbytes_ub = mite_bytes_read_from_memory_ub(mite_chan);
>
> err = a4l_buf_prepare_absget(subd, nbytes_ub);
> if(err < 0) {
> __a4l_info("MITE: DMA underrun\n");
> return -EPIPE;
> }
>
> err = a4l_buf_commit_absget(subd, nbytes_lb);
>
> /* If the MITE has already transfered more than required, we
> can disable it */
> if (test_bit(A4L_BUF_EOA_NR, &buf->flags))
> writel(CHOR_STOP,
> mite_chan->mite->mite_io_addr +
> MITE_CHOR(mite_chan->channel));
>
> return err;
> }
>
> u32 mite_get_status(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> u32 status;
> unsigned long flags;
>
> a4l_lock_irqsave(&mite->lock, flags);
> status = readl(mite->mite_io_addr + MITE_CHSR(mite_chan->channel));
> if (status & CHSR_DONE) {
> mite_chan->done = 1;
> writel(CHOR_CLRDONE,
> mite->mite_io_addr + MITE_CHOR(mite_chan->channel));
> }
> mmiowb();
> a4l_unlock_irqrestore(&mite->lock, flags);
> return status;
> }
>
> int mite_done(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> unsigned long flags;
> int done;
>
> mite_get_status(mite_chan);
> a4l_lock_irqsave(&mite->lock, flags);
> done = mite_chan->done;
> a4l_unlock_irqrestore(&mite->lock, flags);
> return done;
> }
>
> #ifdef CONFIG_DEBUG_MITE
>
> static void mite_decode(const char *const bit_str[], unsigned int bits);
>
> /* names of bits in mite registers */
>
> static const char *const mite_CHOR_strings[] = {
> "start", "cont", "stop", "abort",
> "freset", "clrlc", "clrrb", "clrdone",
> "clr_lpause", "set_lpause", "clr_send_tc",
> "set_send_tc", "12", "13", "14",
> "15", "16", "17", "18",
> "19", "20", "21", "22",
> "23", "24", "25", "26",
> "27", "28", "29", "30",
> "dmareset",
> };
>
> static const char *const mite_CHCR_strings[] = {
> "continue", "ringbuff", "2", "3",
> "4", "5", "6", "7",
> "8", "9", "10", "11",
> "12", "13", "bursten", "fifodis",
> "clr_cont_rb_ie", "set_cont_rb_ie", "clr_lc_ie", "set_lc_ie",
> "clr_drdy_ie", "set_drdy_ie", "clr_mrdy_ie", "set_mrdy_ie",
> "clr_done_ie", "set_done_ie", "clr_sar_ie", "set_sar_ie",
> "clr_linkp_ie", "set_linkp_ie", "clr_dma_ie", "set_dma_ie",
> };
>
> static const char *const mite_MCR_strings[] = {
> "amdevice", "1", "2", "3",
> "4", "5", "portio", "portvxi",
> "psizebyte", "psizehalf (byte & half = word)", "aseqxp1", "11",
> "12", "13", "blocken", "berhand",
> "reqsintlim/reqs0", "reqs1", "reqs2", "rd32",
> "rd512", "rl1", "rl2", "rl8",
> "24", "25", "26", "27",
> "28", "29", "30", "stopen",
> };
>
> static const char *const mite_DCR_strings[] = {
> "amdevice", "1", "2", "3",
> "4", "5", "portio", "portvxi",
> "psizebyte", "psizehalf (byte & half = word)", "aseqxp1", "aseqxp2",
> "aseqxp8", "13", "blocken", "berhand",
> "reqsintlim", "reqs1", "reqs2", "rd32",
> "rd512", "rl1", "rl2", "rl8",
> "23", "24", "25", "27",
> "28", "wsdevc", "wsdevs", "rwdevpack",
> };
>
> static const char *const mite_LKCR_strings[] = {
> "amdevice", "1", "2", "3",
> "4", "5", "portio", "portvxi",
> "psizebyte", "psizehalf (byte & half = word)", "asequp", "aseqdown",
> "12", "13", "14", "berhand",
> "16", "17", "18", "rd32",
> "rd512", "rl1", "rl2", "rl8",
> "24", "25", "26", "27",
> "28", "29", "30", "chngend",
> };
>
> static const char *const mite_CHSR_strings[] = {
> "d.err0", "d.err1", "m.err0", "m.err1",
> "l.err0", "l.err1", "drq0", "drq1",
> "end", "xferr", "operr0", "operr1",
> "stops", "habort", "sabort", "error",
> "16", "conts_rb", "18", "linkc",
> "20", "drdy", "22", "mrdy",
> "24", "done", "26", "sars",
> "28", "lpauses", "30", "int",
> };
>
> void mite_dump_regs(struct mite_channel *mite_chan)
> {
> unsigned long mite_io_addr =
> (unsigned long)mite_chan->mite->mite_io_addr;
> unsigned long addr = 0;
> unsigned long temp = 0;
>
> printk("mite_dump_regs ch%i\n", mite_chan->channel);
> printk("mite address is =0x%08lx\n", mite_io_addr);
>
> addr = mite_io_addr + MITE_CHOR(mite_chan->channel);
> printk("mite status[CHOR]at 0x%08lx =0x%08lx\n", addr, temp =
> readl((void *)addr));
> mite_decode(mite_CHOR_strings, temp);
> addr = mite_io_addr + MITE_CHCR(mite_chan->channel);
> printk("mite status[CHCR]at 0x%08lx =0x%08lx\n", addr, temp =
> readl((void *)addr));
> mite_decode(mite_CHCR_strings, temp);
> addr = mite_io_addr + MITE_TCR(mite_chan->channel);
> printk("mite status[TCR] at 0x%08lx =0x%08x\n", addr,
> readl((void *)addr));
> addr = mite_io_addr + MITE_MCR(mite_chan->channel);
> printk("mite status[MCR] at 0x%08lx =0x%08lx\n", addr, temp =
> readl((void *)addr));
> mite_decode(mite_MCR_strings, temp);
>
> addr = mite_io_addr + MITE_MAR(mite_chan->channel);
> printk("mite status[MAR] at 0x%08lx =0x%08x\n", addr,
> readl((void *)addr));
> addr = mite_io_addr + MITE_DCR(mite_chan->channel);
> printk("mite status[DCR] at 0x%08lx =0x%08lx\n", addr, temp =
> readl((void *)addr));
> mite_decode(mite_DCR_strings, temp);
> addr = mite_io_addr + MITE_DAR(mite_chan->channel);
> printk("mite status[DAR] at 0x%08lx =0x%08x\n", addr,
> readl((void *)addr));
> addr = mite_io_addr + MITE_LKCR(mite_chan->channel);
> printk("mite status[LKCR]at 0x%08lx =0x%08lx\n", addr, temp =
> readl((void *)addr));
> mite_decode(mite_LKCR_strings, temp);
> addr = mite_io_addr + MITE_LKAR(mite_chan->channel);
> printk("mite status[LKAR]at 0x%08lx =0x%08x\n", addr,
> readl((void *)addr));
>
> addr = mite_io_addr + MITE_CHSR(mite_chan->channel);
> printk("mite status[CHSR]at 0x%08lx =0x%08lx\n", addr, temp =
> readl((void *)addr));
> mite_decode(mite_CHSR_strings, temp);
> addr = mite_io_addr + MITE_FCR(mite_chan->channel);
> printk("mite status[FCR] at 0x%08lx =0x%08x\n\n", addr,
> readl((void *)addr));
> }
>
>
> static void mite_decode(const char *const bit_str[], unsigned int bits)
> {
> int i;
>
> for (i = 31; i >= 0; i--) {
> if (bits & (1 << i)) {
> printk(" %s", bit_str[i]);
> }
> }
> printk("\n");
> }
>
> #endif /* CONFIG_DEBUG_MITE */
>
>
> static int __init mite_init(void)
> {
> int err;
>
> /* Register the mite's PCI driver */
> err = pci_register_driver(&mite_driver);
>
> if(err == 0)
> mite_list_devices();
>
> return err;
> }
>
> static void __exit mite_cleanup(void)
> {
>
> /* Unregister the PCI structure driver */
> pci_unregister_driver(&mite_driver);
>
> /* Just paranoia... */
> while(&mite_devices != mite_devices.next) {
> struct list_head *this = mite_devices.next;
> struct mite_struct *mite =
> list_entry(this, struct mite_struct, list);
>
> list_del(this);
> kfree(mite);
> }
> }
>
> MODULE_LICENSE("GPL");
> module_init(mite_init);
> module_exit(mite_cleanup);
>
> EXPORT_SYMBOL_GPL(mite_dma_arm);
> EXPORT_SYMBOL_GPL(mite_dma_disarm);
> EXPORT_SYMBOL_GPL(mite_sync_input_dma);
> EXPORT_SYMBOL_GPL(mite_sync_output_dma);
> EXPORT_SYMBOL_GPL(mite_setup);
> EXPORT_SYMBOL_GPL(mite_unsetup);
> EXPORT_SYMBOL_GPL(mite_list_devices);
> EXPORT_SYMBOL_GPL(mite_request_channel_in_range);
> EXPORT_SYMBOL_GPL(mite_release_channel);
> EXPORT_SYMBOL_GPL(mite_prep_dma);
> EXPORT_SYMBOL_GPL(mite_buf_change);
> EXPORT_SYMBOL_GPL(mite_bytes_written_to_memory_lb);
> EXPORT_SYMBOL_GPL(mite_bytes_written_to_memory_ub);
> EXPORT_SYMBOL_GPL(mite_bytes_read_from_memory_lb);
> EXPORT_SYMBOL_GPL(mite_bytes_read_from_memory_ub);
> EXPORT_SYMBOL_GPL(mite_bytes_in_transit);
> EXPORT_SYMBOL_GPL(mite_get_status);
> EXPORT_SYMBOL_GPL(mite_done);
> #ifdef CONFIG_DEBUG_MITE
> EXPORT_SYMBOL_GPL(mite_decode);
> EXPORT_SYMBOL_GPL(mite_dump_regs);
> #endif /* CONFIG_DEBUG_MITE */
> /*
> comedi/drivers/mite.c
> Hardware driver for NI Mite PCI interface chip
>
> COMEDI - Linux Control and Measurement Device Interface
> Copyright (C) 1997-2002 David A. Schleef <ds@domain.hid>
>
> This program is free software; you can redistribute it and/or modify
> it under the terms of the GNU General Public License as published by
> the Free Software Foundation; either version 2 of the License, or
> (at your option) any later version.
>
> This program is distributed in the hope that it will be useful,
> but WITHOUT ANY WARRANTY; without even the implied warranty of
> MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> GNU General Public License for more details.
>
> You should have received a copy of the GNU General Public License
> along with this program; if not, write to the Free Software
> Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
>
> */
>
> /*
> The PCI-MIO E series driver was originally written by
> Tomasz Motylewski <...>, and ported to comedi by ds.
>
> References for specifications:
>
> 321747b.pdf Register Level Programmer Manual (obsolete)
> 321747c.pdf Register Level Programmer Manual (new)
> DAQ-STC reference manual
>
> Other possibly relevant info:
>
> 320517c.pdf User manual (obsolete)
> 320517f.pdf User manual (new)
> 320889a.pdf delete
> 320906c.pdf maximum signal ratings
> 321066a.pdf about 16x
> 321791a.pdf discontinuation of at-mio-16e-10 rev. c
> 321808a.pdf about at-mio-16e-10 rev P
> 321837a.pdf discontinuation of at-mio-16de-10 rev d
> 321838a.pdf about at-mio-16de-10 rev N
>
> ISSUES:
>
> */
>
> //#define USE_KMALLOC
>
> #include "mite.h"
>
> #include "comedi_fc.h"
> #include "comedi_pci.h"
> #include <linux/comedidev.h>
>
> #include <asm/system.h>
>
> #define PCI_MITE_SIZE 4096
> #define PCI_DAQ_SIZE 4096
> #define PCI_DAQ_SIZE_660X 8192
>
> MODULE_LICENSE("GPL");
>
> struct mite_struct *mite_devices = NULL;
>
> #define TOP_OF_PAGE(x) ((x)|(~(PAGE_MASK)))
>
> void mite_init(void)
> {
> struct pci_dev *pcidev;
> struct mite_struct *mite;
>
> for (pcidev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, NULL);
> pcidev != NULL;
> pcidev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, pcidev)) {
> if (pcidev->vendor == PCI_VENDOR_ID_NATINST) {
> unsigned i;
>
> mite = kzalloc(sizeof(*mite), GFP_KERNEL);
> if (!mite) {
> printk("mite: allocation failed\n");
> pci_dev_put(pcidev);
> return;
> }
> spin_lock_init(&mite->lock);
> mite->pcidev = pci_dev_get(pcidev);
> for (i = 0; i < MAX_MITE_DMA_CHANNELS; ++i) {
> mite->channels[i].mite = mite;
> mite->channels[i].channel = i;
> mite->channels[i].done = 1;
> }
> mite->next = mite_devices;
> mite_devices = mite;
> }
> }
> }
>
> static void dump_chip_signature(u32 csigr_bits)
> {
> printk("mite: version = %i, type = %i, mite mode = %i, interface mode = %i\n", mite_csigr_version(csigr_bits), mite_csigr_type(csigr_bits), mite_csigr_mmode(csigr_bits), mite_csigr_imode(csigr_bits));
> printk("mite: num channels = %i, write post fifo depth = %i, wins = %i, iowins = %i\n", mite_csigr_dmac(csigr_bits), mite_csigr_wpdep(csigr_bits), mite_csigr_wins(csigr_bits), mite_csigr_iowins(csigr_bits));
> }
>
> unsigned mite_fifo_size(struct mite_struct * mite, unsigned channel)
> {
> unsigned fcr_bits = readl(mite->mite_io_addr +
> MITE_FCR(channel));
> unsigned empty_count = (fcr_bits >> 16) & 0xff;
> unsigned full_count = fcr_bits & 0xff;
> return empty_count + full_count;
> }
>
> int mite_setup2(struct mite_struct *mite, unsigned use_iodwbsr_1)
> {
> unsigned long length;
> resource_size_t addr;
> int i;
> u32 csigr_bits;
> unsigned unknown_dma_burst_bits;
>
> if (comedi_pci_enable(mite->pcidev, "mite")) {
> printk("error enabling mite and requesting io regions\n");
> return -EIO;
> }
> pci_set_master(mite->pcidev);
>
> addr = pci_resource_start(mite->pcidev, 0);
> mite->mite_phys_addr = addr;
> mite->mite_io_addr = ioremap(addr, PCI_MITE_SIZE);
> if (!mite->mite_io_addr) {
> printk("failed to remap mite io memory address\n");
> return -ENOMEM;
> }
> printk("MITE:0x%08llx mapped to %p ",
> (unsigned long long)mite->mite_phys_addr, mite->mite_io_addr);
>
> addr = pci_resource_start(mite->pcidev, 1);
> mite->daq_phys_addr = addr;
> length = pci_resource_len(mite->pcidev, 1);
> // In case of a 660x board, DAQ size is 8k instead of 4k (see as shown by lspci output)
> mite->daq_io_addr = ioremap(mite->daq_phys_addr, length);
> if (!mite->daq_io_addr) {
> printk("failed to remap daq io memory address\n");
> return -ENOMEM;
> }
> printk("DAQ:0x%08llx mapped to %p\n",
> (unsigned long long)mite->daq_phys_addr, mite->daq_io_addr);
>
> if (use_iodwbsr_1) {
> writel(0, mite->mite_io_addr + MITE_IODWBSR);
> printk("mite: using I/O Window Base Size register 1\n");
> writel(mite->
> daq_phys_addr | WENAB |
> MITE_IODWBSR_1_WSIZE_bits(length),
> mite->mite_io_addr + MITE_IODWBSR_1);
> writel(0, mite->mite_io_addr + MITE_IODWCR_1);
> } else {
> writel(mite->daq_phys_addr | WENAB,
> mite->mite_io_addr + MITE_IODWBSR);
> }
> /* make sure dma bursts work. I got this from running a bus analyzer
> on a pxi-6281 and a pxi-6713. 6713 powered up with register value
> of 0x61f and bursts worked. 6281 powered up with register value of
> 0x1f and bursts didn't work. The NI windows driver reads the register,
> then does a bitwise-or of 0x600 with it and writes it back.
> */
> unknown_dma_burst_bits =
> readl(mite->mite_io_addr + MITE_UNKNOWN_DMA_BURST_REG);
> unknown_dma_burst_bits |= UNKNOWN_DMA_BURST_ENABLE_BITS;
> writel(unknown_dma_burst_bits,
> mite->mite_io_addr + MITE_UNKNOWN_DMA_BURST_REG);
>
> csigr_bits = readl(mite->mite_io_addr + MITE_CSIGR);
> mite->num_channels = mite_csigr_dmac(csigr_bits);
> if (mite->num_channels > MAX_MITE_DMA_CHANNELS) {
> printk("mite: bug? chip claims to have %i dma channels. Setting to %i.\n", mite->num_channels, MAX_MITE_DMA_CHANNELS);
> mite->num_channels = MAX_MITE_DMA_CHANNELS;
> }
> dump_chip_signature(csigr_bits);
> for (i = 0; i < mite->num_channels; i++) {
> writel(CHOR_DMARESET, mite->mite_io_addr + MITE_CHOR(i));
> /* disable interrupts */
> writel(CHCR_CLR_DMA_IE | CHCR_CLR_LINKP_IE | CHCR_CLR_SAR_IE |
> CHCR_CLR_DONE_IE | CHCR_CLR_MRDY_IE | CHCR_CLR_DRDY_IE |
> CHCR_CLR_LC_IE | CHCR_CLR_CONT_RB_IE,
> mite->mite_io_addr + MITE_CHCR(i));
> }
> mite->fifo_size = mite_fifo_size(mite, 0);
> printk("mite: fifo size is %i.\n", mite->fifo_size);
> mite->used = 1;
>
> return 0;
> }
>
> int mite_setup(struct mite_struct *mite)
> {
> return mite_setup2(mite, 0);
> }
>
> void mite_cleanup(void)
> {
> struct mite_struct *mite, *next;
>
> for (mite = mite_devices; mite; mite = next) {
> pci_dev_put(mite->pcidev);
> next = mite->next;
> kfree(mite);
> }
> }
>
> void mite_unsetup(struct mite_struct *mite)
> {
> //unsigned long offset, start, length;
>
> if (!mite)
> return;
>
> if (mite->mite_io_addr) {
> iounmap(mite->mite_io_addr);
> mite->mite_io_addr = NULL;
> }
> if (mite->daq_io_addr) {
> iounmap(mite->daq_io_addr);
> mite->daq_io_addr = NULL;
> }
> if (mite->mite_phys_addr) {
> comedi_pci_disable(mite->pcidev);
> mite->mite_phys_addr = 0;
> }
>
> mite->used = 0;
> }
>
> void mite_list_devices(void)
> {
> struct mite_struct *mite, *next;
>
> printk("Available NI device IDs:");
> if (mite_devices)
> for (mite = mite_devices; mite; mite = next) {
> next = mite->next;
> printk(" 0x%04x", mite_device_id(mite));
> if (mite->used)
> printk("(used)");
> }
> printk("\n");
>
> }
>
> struct mite_channel *mite_request_channel_in_range(struct mite_struct *mite,
> struct mite_dma_descriptor_ring *ring, unsigned min_channel,
> unsigned max_channel)
> {
> int i;
> unsigned long flags;
> struct mite_channel *channel = NULL;
>
> // spin lock so mite_release_channel can be called safely from interrupts
> comedi_spin_lock_irqsave(&mite->lock, flags);
> for (i = min_channel; i <= max_channel; ++i) {
> if (mite->channel_allocated[i] == 0) {
> mite->channel_allocated[i] = 1;
> channel = &mite->channels[i];
> channel->ring = ring;
> break;
> }
> }
> comedi_spin_unlock_irqrestore(&mite->lock, flags);
> return channel;
> }
>
> void mite_release_channel(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> unsigned long flags;
>
> // spin lock to prevent races with mite_request_channel
> comedi_spin_lock_irqsave(&mite->lock, flags);
> if (mite->channel_allocated[mite_chan->channel]) {
> mite_dma_disarm(mite_chan);
> mite_dma_reset(mite_chan);
> /* disable all channel's interrupts (do it after disarm/reset so
> MITE_CHCR reg isn't changed while dma is still active!) */
> writel(CHCR_CLR_DMA_IE | CHCR_CLR_LINKP_IE |
> CHCR_CLR_SAR_IE | CHCR_CLR_DONE_IE |
> CHCR_CLR_MRDY_IE | CHCR_CLR_DRDY_IE |
> CHCR_CLR_LC_IE | CHCR_CLR_CONT_RB_IE,
> mite->mite_io_addr + MITE_CHCR(mite_chan->channel));
> mite->channel_allocated[mite_chan->channel] = 0;
> mite_chan->ring = NULL;
> mmiowb();
> }
> comedi_spin_unlock_irqrestore(&mite->lock, flags);
> }
>
> void mite_dma_arm(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> int chor;
> unsigned long flags;
>
> MDPRINTK("mite_dma_arm ch%i\n", channel);
> /* memory barrier is intended to insure any twiddling with the buffer
> is done before writing to the mite to arm dma transfer */
> smp_mb();
> /* arm */
> chor = CHOR_START;
> comedi_spin_lock_irqsave(&mite->lock, flags);
> mite_chan->done = 0;
> writel(chor, mite->mite_io_addr + MITE_CHOR(mite_chan->channel));
> mmiowb();
> comedi_spin_unlock_irqrestore(&mite->lock, flags);
> // mite_dma_tcr(mite, channel);
> }
>
> /**************************************/
>
> int mite_buf_change(struct mite_dma_descriptor_ring *ring, comedi_async * async)
> {
> unsigned int n_links;
> int i;
>
> if (ring->descriptors) {
> dma_free_coherent(ring->hw_dev,
> ring->n_links * sizeof(struct mite_dma_descriptor),
> ring->descriptors, ring->descriptors_dma_addr);
> }
> ring->descriptors = NULL;
> ring->descriptors_dma_addr = 0;
> ring->n_links = 0;
>
> if (async->prealloc_bufsz == 0) {
> return 0;
> }
> n_links = async->prealloc_bufsz >> PAGE_SHIFT;
>
> MDPRINTK("ring->hw_dev=%p, n_links=0x%04x\n", ring->hw_dev, n_links);
>
> ring->descriptors =
> dma_alloc_coherent(ring->hw_dev,
> n_links * sizeof(struct mite_dma_descriptor),
> &ring->descriptors_dma_addr, GFP_KERNEL);
> if (!ring->descriptors) {
> printk("mite: ring buffer allocation failed\n");
> return -ENOMEM;
> }
> ring->n_links = n_links;
>
> for (i = 0; i < n_links; i++) {
> ring->descriptors[i].count = cpu_to_le32(PAGE_SIZE);
> ring->descriptors[i].addr =
> cpu_to_le32(async->buf_page_list[i].dma_addr);
> ring->descriptors[i].next =
> cpu_to_le32(ring->descriptors_dma_addr + (i +
> 1) * sizeof(struct mite_dma_descriptor));
> }
> ring->descriptors[n_links - 1].next =
> cpu_to_le32(ring->descriptors_dma_addr);
> /* barrier is meant to insure that all the writes to the dma descriptors
> have completed before the dma controller is commanded to read them */
> smp_wmb();
> return 0;
> }
>
> void mite_prep_dma(struct mite_channel *mite_chan,
> unsigned int num_device_bits, unsigned int num_memory_bits)
> {
> unsigned int chor, chcr, mcr, dcr, lkcr;
> struct mite_struct *mite = mite_chan->mite;
>
> MDPRINTK("mite_prep_dma ch%i\n", mite_chan->channel);
>
> /* reset DMA and FIFO */
> chor = CHOR_DMARESET | CHOR_FRESET;
> writel(chor, mite->mite_io_addr + MITE_CHOR(mite_chan->channel));
>
> /* short link chaining mode */
> chcr = CHCR_SET_DMA_IE | CHCR_LINKSHORT | CHCR_SET_DONE_IE |
> CHCR_BURSTEN;
> /*
> * Link Complete Interrupt: interrupt every time a link
> * in MITE_RING is completed. This can generate a lot of
> * extra interrupts, but right now we update the values
> * of buf_int_ptr and buf_int_count at each interrupt. A
> * better method is to poll the MITE before each user
> * "read()" to calculate the number of bytes available.
> */
> chcr |= CHCR_SET_LC_IE;
> if (num_memory_bits == 32 && num_device_bits == 16) {
> /* Doing a combined 32 and 16 bit byteswap gets the 16 bit samples into the fifo in the right order.
> Tested doing 32 bit memory to 16 bit device transfers to the analog out of a pxi-6281,
> which has mite version = 1, type = 4. This also works for dma reads from the counters
> on e-series boards. */
> chcr |= CHCR_BYTE_SWAP_DEVICE | CHCR_BYTE_SWAP_MEMORY;
> }
> if (mite_chan->dir == COMEDI_INPUT) {
> chcr |= CHCR_DEV_TO_MEM;
> }
> writel(chcr, mite->mite_io_addr + MITE_CHCR(mite_chan->channel));
>
> /* to/from memory */
> mcr = CR_RL(64) | CR_ASEQUP;
> switch (num_memory_bits) {
> case 8:
> mcr |= CR_PSIZE8;
> break;
> case 16:
> mcr |= CR_PSIZE16;
> break;
> case 32:
> mcr |= CR_PSIZE32;
> break;
> default:
> rt_printk
> ("mite: bug! invalid mem bit width for dma transfer\n");
> break;
> }
> writel(mcr, mite->mite_io_addr + MITE_MCR(mite_chan->channel));
>
> /* from/to device */
> dcr = CR_RL(64) | CR_ASEQUP;
> dcr |= CR_PORTIO | CR_AMDEVICE | CR_REQSDRQ(mite_chan->channel);
> switch (num_device_bits) {
> case 8:
> dcr |= CR_PSIZE8;
> break;
> case 16:
> dcr |= CR_PSIZE16;
> break;
> case 32:
> dcr |= CR_PSIZE32;
> break;
> default:
> rt_printk
> ("mite: bug! invalid dev bit width for dma transfer\n");
> break;
> }
> writel(dcr, mite->mite_io_addr + MITE_DCR(mite_chan->channel));
>
> /* reset the DAR */
> writel(0, mite->mite_io_addr + MITE_DAR(mite_chan->channel));
>
> /* the link is 32bits */
> lkcr = CR_RL(64) | CR_ASEQUP | CR_PSIZE32;
> writel(lkcr, mite->mite_io_addr + MITE_LKCR(mite_chan->channel));
>
> /* starting address for link chaining */
> writel(mite_chan->ring->descriptors_dma_addr,
> mite->mite_io_addr + MITE_LKAR(mite_chan->channel));
>
> MDPRINTK("exit mite_prep_dma\n");
> }
>
> u32 mite_device_bytes_transferred(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> return readl(mite->mite_io_addr + MITE_DAR(mite_chan->channel));
> }
>
> u32 mite_bytes_in_transit(struct mite_channel * mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> return readl(mite->mite_io_addr +
> MITE_FCR(mite_chan->channel)) & 0x000000FF;
> }
>
> // returns lower bound for number of bytes transferred from device to memory
> u32 mite_bytes_written_to_memory_lb(struct mite_channel * mite_chan)
> {
> u32 device_byte_count;
>
> device_byte_count = mite_device_bytes_transferred(mite_chan);
> return device_byte_count - mite_bytes_in_transit(mite_chan);
> }
>
> // returns upper bound for number of bytes transferred from device to memory
> u32 mite_bytes_written_to_memory_ub(struct mite_channel * mite_chan)
> {
> u32 in_transit_count;
>
> in_transit_count = mite_bytes_in_transit(mite_chan);
> return mite_device_bytes_transferred(mite_chan) - in_transit_count;
> }
>
> // returns lower bound for number of bytes read from memory for transfer to device
> u32 mite_bytes_read_from_memory_lb(struct mite_channel * mite_chan)
> {
> u32 device_byte_count;
>
> device_byte_count = mite_device_bytes_transferred(mite_chan);
> return device_byte_count + mite_bytes_in_transit(mite_chan);
> }
>
> // returns upper bound for number of bytes read from memory for transfer to device
> u32 mite_bytes_read_from_memory_ub(struct mite_channel * mite_chan)
> {
> u32 in_transit_count;
>
> in_transit_count = mite_bytes_in_transit(mite_chan);
> return mite_device_bytes_transferred(mite_chan) + in_transit_count;
> }
>
> unsigned mite_dma_tcr(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> int tcr;
> int lkar;
>
> lkar = readl(mite->mite_io_addr + MITE_LKAR(mite_chan->channel));
> tcr = readl(mite->mite_io_addr + MITE_TCR(mite_chan->channel));
> MDPRINTK("mite_dma_tcr ch%i, lkar=0x%08x tcr=%d\n", mite_chan->channel,
> lkar, tcr);
>
> return tcr;
> }
>
> void mite_dma_disarm(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> unsigned chor;
>
> /* disarm */
> chor = CHOR_ABORT;
> writel(chor, mite->mite_io_addr + MITE_CHOR(mite_chan->channel));
> }
>
> int mite_sync_input_dma(struct mite_channel *mite_chan, comedi_async * async)
> {
> int count;
> unsigned int nbytes, old_alloc_count;
> const unsigned bytes_per_scan = cfc_bytes_per_scan(async->subdevice);
>
> old_alloc_count = async->buf_write_alloc_count;
> // write alloc as much as we can
> comedi_buf_write_alloc(async, async->prealloc_bufsz);
>
> nbytes = mite_bytes_written_to_memory_lb(mite_chan);
> if ((int)(mite_bytes_written_to_memory_ub(mite_chan) -
> old_alloc_count) > 0) {
> rt_printk("mite: DMA overwrite of free area\n");
> async->events |= COMEDI_CB_OVERFLOW;
> return -1;
> }
>
> count = nbytes - async->buf_write_count;
> /* it's possible count will be negative due to
> * conservative value returned by mite_bytes_written_to_memory_lb */
> if (count <= 0) {
> return 0;
> }
> comedi_buf_write_free(async, count);
>
> async->scan_progress += count;
> if (async->scan_progress >= bytes_per_scan) {
> async->scan_progress %= bytes_per_scan;
> async->events |= COMEDI_CB_EOS;
> }
> async->events |= COMEDI_CB_BLOCK;
> return 0;
> }
>
> int mite_sync_output_dma(struct mite_channel *mite_chan, comedi_async * async)
> {
> int count;
> u32 nbytes_ub, nbytes_lb;
> unsigned int old_alloc_count;
> u32 stop_count =
> async->cmd.stop_arg * cfc_bytes_per_scan(async->subdevice);
>
> old_alloc_count = async->buf_read_alloc_count;
> // read alloc as much as we can
> comedi_buf_read_alloc(async, async->prealloc_bufsz);
> nbytes_lb = mite_bytes_read_from_memory_lb(mite_chan);
> if (async->cmd.stop_src == TRIG_COUNT &&
> (int)(nbytes_lb - stop_count) > 0)
> nbytes_lb = stop_count;
> nbytes_ub = mite_bytes_read_from_memory_ub(mite_chan);
> if (async->cmd.stop_src == TRIG_COUNT &&
> (int)(nbytes_ub - stop_count) > 0)
> nbytes_ub = stop_count;
> if ((int)(nbytes_ub - old_alloc_count) > 0) {
> rt_printk("mite: DMA underrun\n");
> async->events |= COMEDI_CB_OVERFLOW;
> return -1;
> }
> count = nbytes_lb - async->buf_read_count;
> if (count <= 0) {
> return 0;
> }
> if (count) {
> comedi_buf_read_free(async, count);
> async->events |= COMEDI_CB_BLOCK;
> }
> return 0;
> }
>
> unsigned mite_get_status(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> unsigned status;
> unsigned long flags;
>
> comedi_spin_lock_irqsave(&mite->lock, flags);
> status = readl(mite->mite_io_addr + MITE_CHSR(mite_chan->channel));
> if (status & CHSR_DONE) {
> mite_chan->done = 1;
> writel(CHOR_CLRDONE,
> mite->mite_io_addr + MITE_CHOR(mite_chan->channel));
> }
> mmiowb();
> comedi_spin_unlock_irqrestore(&mite->lock, flags);
> return status;
> }
>
> int mite_done(struct mite_channel *mite_chan)
> {
> struct mite_struct *mite = mite_chan->mite;
> unsigned long flags;
> int done;
>
> mite_get_status(mite_chan);
> comedi_spin_lock_irqsave(&mite->lock, flags);
> done = mite_chan->done;
> comedi_spin_unlock_irqrestore(&mite->lock, flags);
> return done;
> }
>
> #ifdef DEBUG_MITE
>
> static void mite_decode(char **bit_str, unsigned int bits);
>
> /* names of bits in mite registers */
>
> static const char *const mite_CHOR_strings[] = {
> "start", "cont", "stop", "abort",
> "freset", "clrlc", "clrrb", "clrdone",
> "clr_lpause", "set_lpause", "clr_send_tc",
> "set_send_tc", "12", "13", "14",
> "15", "16", "17", "18",
> "19", "20", "21", "22",
> "23", "24", "25", "26",
> "27", "28", "29", "30",
> "dmareset",
> };
>
> static const char *const mite_CHCR_strings[] = {
> "continue", "ringbuff", "2", "3",
> "4", "5", "6", "7",
> "8", "9", "10", "11",
> "12", "13", "bursten", "fifodis",
> "clr_cont_rb_ie", "set_cont_rb_ie", "clr_lc_ie", "set_lc_ie",
> "clr_drdy_ie", "set_drdy_ie", "clr_mrdy_ie", "set_mrdy_ie",
> "clr_done_ie", "set_done_ie", "clr_sar_ie", "set_sar_ie",
> "clr_linkp_ie", "set_linkp_ie", "clr_dma_ie", "set_dma_ie",
> };
>
> static const char *const mite_MCR_strings[] = {
> "amdevice", "1", "2", "3",
> "4", "5", "portio", "portvxi",
> "psizebyte", "psizehalf (byte & half = word)", "aseqxp1", "11",
> "12", "13", "blocken", "berhand",
> "reqsintlim/reqs0", "reqs1", "reqs2", "rd32",
> "rd512", "rl1", "rl2", "rl8",
> "24", "25", "26", "27",
> "28", "29", "30", "stopen",
> };
>
> static const char *const mite_DCR_strings[] = {
> "amdevice", "1", "2", "3",
> "4", "5", "portio", "portvxi",
> "psizebyte", "psizehalf (byte & half = word)", "aseqxp1", "aseqxp2",
> "aseqxp8", "13", "blocken", "berhand",
> "reqsintlim", "reqs1", "reqs2", "rd32",
> "rd512", "rl1", "rl2", "rl8",
> "23", "24", "25", "27",
> "28", "wsdevc", "wsdevs", "rwdevpack",
> };
>
> static const char *const mite_LKCR_strings[] = {
> "amdevice", "1", "2", "3",
> "4", "5", "portio", "portvxi",
> "psizebyte", "psizehalf (byte & half = word)", "asequp", "aseqdown",
> "12", "13", "14", "berhand",
> "16", "17", "18", "rd32",
> "rd512", "rl1", "rl2", "rl8",
> "24", "25", "26", "27",
> "28", "29", "30", "chngend",
> };
>
> static const char *const mite_CHSR_strings[] = {
> "d.err0", "d.err1", "m.err0", "m.err1",
> "l.err0", "l.err1", "drq0", "drq1",
> "end", "xferr", "operr0", "operr1",
> "stops", "habort", "sabort", "error",
> "16", "conts_rb", "18", "linkc",
> "20", "drdy", "22", "mrdy",
> "24", "done", "26", "sars",
> "28", "lpauses", "30", "int",
> };
>
> void mite_dump_regs(struct mite_channel *mite_chan)
> {
> unsigned long mite_io_addr =
> (unsigned long)mite_chan->mite->mite_io_addr;
> unsigned long addr = 0;
> unsigned long temp = 0;
>
> printk("mite_dump_regs ch%i\n", mite_chan->channel);
> printk("mite address is =0x%08lx\n", mite_io_addr);
>
> addr = mite_io_addr + MITE_CHOR(channel);
> printk("mite status[CHOR]at 0x%08lx =0x%08lx\n", addr, temp =
> readl(addr));
> mite_decode(mite_CHOR_strings, temp);
> addr = mite_io_addr + MITE_CHCR(channel);
> printk("mite status[CHCR]at 0x%08lx =0x%08lx\n", addr, temp =
> readl(addr));
> mite_decode(mite_CHCR_strings, temp);
> addr = mite_io_addr + MITE_TCR(channel);
> printk("mite status[TCR] at 0x%08lx =0x%08x\n", addr, readl(addr));
> addr = mite_io_addr + MITE_MCR(channel);
> printk("mite status[MCR] at 0x%08lx =0x%08lx\n", addr, temp =
> readl(addr));
> mite_decode(mite_MCR_strings, temp);
>
> addr = mite_io_addr + MITE_MAR(channel);
> printk("mite status[MAR] at 0x%08lx =0x%08x\n", addr, readl(addr));
> addr = mite_io_addr + MITE_DCR(channel);
> printk("mite status[DCR] at 0x%08lx =0x%08lx\n", addr, temp =
> readl(addr));
> mite_decode(mite_DCR_strings, temp);
> addr = mite_io_addr + MITE_DAR(channel);
> printk("mite status[DAR] at 0x%08lx =0x%08x\n", addr, readl(addr));
> addr = mite_io_addr + MITE_LKCR(channel);
> printk("mite status[LKCR]at 0x%08lx =0x%08lx\n", addr, temp =
> readl(addr));
> mite_decode(mite_LKCR_strings, temp);
> addr = mite_io_addr + MITE_LKAR(channel);
> printk("mite status[LKAR]at 0x%08lx =0x%08x\n", addr, readl(addr));
>
> addr = mite_io_addr + MITE_CHSR(channel);
> printk("mite status[CHSR]at 0x%08lx =0x%08lx\n", addr, temp =
> readl(addr));
> mite_decode(mite_CHSR_strings, temp);
> addr = mite_io_addr + MITE_FCR(channel);
> printk("mite status[FCR] at 0x%08lx =0x%08x\n\n", addr, readl(addr));
> }
>
> static void mite_decode(char **bit_str, unsigned int bits)
> {
> int i;
>
> for (i = 31; i >= 0; i--) {
> if (bits & (1 << i)) {
> printk(" %s", bit_str[i]);
> }
> }
> printk("\n");
> }
> #endif
>
> #ifdef MODULE
> int __init init_module(void)
> {
> mite_init();
> mite_list_devices();
>
> return 0;
> }
>
> void __exit cleanup_module(void)
> {
> mite_cleanup();
> }
>
> EXPORT_SYMBOL(mite_dma_tcr);
> EXPORT_SYMBOL(mite_dma_arm);
> EXPORT_SYMBOL(mite_dma_disarm);
> EXPORT_SYMBOL(mite_sync_input_dma);
> EXPORT_SYMBOL(mite_sync_output_dma);
> EXPORT_SYMBOL(mite_setup);
> EXPORT_SYMBOL(mite_setup2);
> EXPORT_SYMBOL(mite_unsetup);
> #if 0
> EXPORT_SYMBOL(mite_kvmem_segment_load);
> EXPORT_SYMBOL(mite_ll_from_kvmem);
> EXPORT_SYMBOL(mite_setregs);
> #endif
> EXPORT_SYMBOL(mite_devices);
> EXPORT_SYMBOL(mite_list_devices);
> EXPORT_SYMBOL(mite_request_channel_in_range);
> EXPORT_SYMBOL(mite_release_channel);
> EXPORT_SYMBOL(mite_prep_dma);
> EXPORT_SYMBOL(mite_buf_change);
> EXPORT_SYMBOL(mite_bytes_written_to_memory_lb);
> EXPORT_SYMBOL(mite_bytes_written_to_memory_ub);
> EXPORT_SYMBOL(mite_bytes_read_from_memory_lb);
> EXPORT_SYMBOL(mite_bytes_read_from_memory_ub);
> EXPORT_SYMBOL(mite_bytes_in_transit);
> EXPORT_SYMBOL(mite_get_status);
> EXPORT_SYMBOL(mite_done);
> #ifdef DEBUG_MITE
> EXPORT_SYMBOL(mite_decode);
> EXPORT_SYMBOL(mite_dump_regs);
> #endif
>
> #endif
> /*
> * comedi/drivers/adl_pci9118.c
> *
> * hardware driver for ADLink cards:
> * card: PCI-9118DG, PCI-9118HG, PCI-9118HR
> * driver: pci9118dg, pci9118hg, pci9118hr
> *
> * Author: Michal Dobes <dobes@domain.hid>
> *
> */
> /*
> Driver: adl_pci9118
> Description: Adlink PCI-9118DG, PCI-9118HG, PCI-9118HR
> Author: Michal Dobes <dobes@domain.hid>
> Devices: [ADLink] PCI-9118DG (pci9118dg), PCI-9118HG (pci9118hg),
> PCI-9118HR (pci9118hr)
> Status: works
>
> This driver supports AI, AO, DI and DO subdevices.
> AI subdevice supports cmd and insn interface,
> other subdevices support only insn interface.
> For AI:
> - If cmd->scan_begin_src=TRIG_EXT then trigger input is TGIN (pin 46).
> - If cmd->convert_src=TRIG_EXT then trigger input is EXTTRG (pin 44).
> - If cmd->start_src/stop_src=TRIG_EXT then trigger input is TGIN (pin 46).
> - It is not neccessary to have cmd.scan_end_arg=cmd.chanlist_len but
> cmd.scan_end_arg modulo cmd.chanlist_len must by 0.
> - If return value of cmdtest is 5 then you've bad channel list
> (it isn't possible mixture S.E. and DIFF inputs or bipolar and unipolar
> ranges).
>
> There are some hardware limitations:
> a) You cann't use mixture of unipolar/bipoar ranges or differencial/single
> ended inputs.
> b) DMA transfers must have the length aligned to two samples (32 bit),
> so there is some problems if cmd->chanlist_len is odd. This driver tries
> bypass this with adding one sample to the end of the every scan and discard
> it on output but this cann't be used if cmd->scan_begin_src=TRIG_FOLLOW
> and is used flag TRIG_WAKE_EOS, then driver switch to interrupt driven mode
> with interrupt after every sample.
> c) If isn't used DMA then you can use only mode where
> cmd->scan_begin_src=TRIG_FOLLOW.
>
> Configuration options:
> [0] - PCI bus of device (optional)
> [1] - PCI slot of device (optional)
> If bus/slot is not specified, then first available PCI
> card will be used.
> [2] - 0= standard 8 DIFF/16 SE channels configuration
> n= external multiplexer connected, 1<=n<=256
> [3] - 0=autoselect DMA or EOC interrupts operation
> 1=disable DMA mode
> 3=disable DMA and INT, only insn interface will work
> [4] - sample&hold signal - card can generate signal for external S&H board
> 0=use SSHO (pin 45) signal is generated in onboard hardware S&H logic
> 0!=use ADCHN7 (pin 23) signal is generated from driver, number
> say how long delay is requested in ns and sign polarity of the hold
> (in this case external multiplexor can serve only 128 channels)
> [5] - 0=stop measure on all hardware errors
> 2|=ignore ADOR - A/D Overrun status
> 8|=ignore Bover - A/D Burst Mode Overrun status
> 256|=ignore nFull - A/D FIFO Full status
>
> */
> #include <linux/comedidev.h>
>
> #include <linux/delay.h>
>
> #include "amcc_s5933.h"
> #include "8253.h"
> #include "comedi_pci.h"
> #include "comedi_fc.h"
>
> /* paranoid checks are broken */
> #undef PCI9118_PARANOIDCHECK /* if defined, then is used code which control correct channel number on every 12 bit sample */
>
> #undef PCI9118_EXTDEBUG /* if defined then driver prints a lot of messages */
>
> #undef DPRINTK
> #ifdef PCI9118_EXTDEBUG
> #define DPRINTK(fmt, args...) rt_printk(fmt, ## args)
> #else
> #define DPRINTK(fmt, args...)
> #endif
>
> #define IORANGE_9118 64 /* I hope */
> #define PCI9118_CHANLEN 255 /* len of chanlist, some source say 256, but reality looks like 255 :-( */
>
> #define PCI9118_CNT0 0x00 /* R/W: 8254 couter 0 */
> #define PCI9118_CNT1 0x04 /* R/W: 8254 couter 0 */
> #define PCI9118_CNT2 0x08 /* R/W: 8254 couter 0 */
> #define PCI9118_CNTCTRL 0x0c /* W: 8254 counter control */
> #define PCI9118_AD_DATA 0x10 /* R: A/D data */
> #define PCI9118_DA1 0x10 /* W: D/A registers */
> #define PCI9118_DA2 0x14
> #define PCI9118_ADSTAT 0x18 /* R: A/D status register */
> #define PCI9118_ADCNTRL 0x18 /* W: A/D control register */
> #define PCI9118_DI 0x1c /* R: digi input register */
> #define PCI9118_DO 0x1c /* W: digi output register */
> #define PCI9118_SOFTTRG 0x20 /* W: soft trigger for A/D */
> #define PCI9118_GAIN 0x24 /* W: A/D gain/channel register */
> #define PCI9118_BURST 0x28 /* W: A/D burst number register */
> #define PCI9118_SCANMOD 0x2c /* W: A/D auto scan mode */
> #define PCI9118_ADFUNC 0x30 /* W: A/D function register */
> #define PCI9118_DELFIFO 0x34 /* W: A/D data FIFO reset */
> #define PCI9118_INTSRC 0x38 /* R: interrupt reason register */
> #define PCI9118_INTCTRL 0x38 /* W: interrupt control register */
>
> // bits from A/D control register (PCI9118_ADCNTRL)
> #define AdControl_UniP 0x80 /* 1=bipolar, 0=unipolar */
> #define AdControl_Diff 0x40 /* 1=differential, 0= single end inputs */
> #define AdControl_SoftG 0x20 /* 1=8254 counter works, 0=counter stops */
> #define AdControl_ExtG 0x10 /* 1=8254 countrol controlled by TGIN(pin 46), 0=controled by SoftG */
> #define AdControl_ExtM 0x08 /* 1=external hardware trigger (pin 44), 0=internal trigger */
> #define AdControl_TmrTr 0x04 /* 1=8254 is iternal trigger source, 0=software trigger is source (register PCI9118_SOFTTRG) */
> #define AdControl_Int 0x02 /* 1=enable INT, 0=disable */
> #define AdControl_Dma 0x01 /* 1=enable DMA, 0=disable */
>
> // bits from A/D function register (PCI9118_ADFUNC)
> #define AdFunction_PDTrg 0x80 /* 1=positive, 0=negative digital trigger (only positive is correct) */
> #define AdFunction_PETrg 0x40 /* 1=positive, 0=negative external trigger (only positive is correct) */
> #define AdFunction_BSSH 0x20 /* 1=with sample&hold, 0=without */
> #define AdFunction_BM 0x10 /* 1=burst mode, 0=normal mode */
> #define AdFunction_BS 0x08 /* 1=burst mode start, 0=burst mode stop */
> #define AdFunction_PM 0x04 /* 1=post trigger mode, 0=not post trigger */
> #define AdFunction_AM 0x02 /* 1=about trigger mode, 0=not about trigger */
> #define AdFunction_Start 0x01 /* 1=trigger start, 0=trigger stop */
>
> // bits from A/D status register (PCI9118_ADSTAT)
> #define AdStatus_nFull 0x100 /* 0=FIFO full (fatal), 1=not full */
> #define AdStatus_nHfull 0x080 /* 0=FIFO half full, 1=FIFO not half full */
> #define AdStatus_nEpty 0x040 /* 0=FIFO empty, 1=FIFO not empty */
> #define AdStatus_Acmp 0x020 /* */
> #define AdStatus_DTH 0x010 /* 1=external digital trigger */
> #define AdStatus_Bover 0x008 /* 1=burst mode overrun (fatal) */
> #define AdStatus_ADOS 0x004 /* 1=A/D over speed (warning) */
> #define AdStatus_ADOR 0x002 /* 1=A/D overrun (fatal) */
> #define AdStatus_ADrdy 0x001 /* 1=A/D already ready, 0=not ready */
>
> // bits for interrupt reason and control (PCI9118_INTSRC, PCI9118_INTCTRL)
> // 1=interrupt occur, enable source, 0=interrupt not occur, disable source
> #define Int_Timer 0x08 /* timer interrupt */
> #define Int_About 0x04 /* about trigger complete */
> #define Int_Hfull 0x02 /* A/D FIFO hlaf full */
> #define Int_DTrg 0x01 /* external digital trigger */
>
> #define START_AI_EXT 0x01 /* start measure on external trigger */
> #define STOP_AI_EXT 0x02 /* stop measure on external trigger */
> #define START_AI_INT 0x04 /* start measure on internal trigger */
> #define STOP_AI_INT 0x08 /* stop measure on internal trigger */
>
> #define EXTTRG_AI 0 /* ext trg is used by AI */
>
> static const comedi_lrange range_pci9118dg_hr = { 8, {
> BIP_RANGE(5),
> BIP_RANGE(2.5),
> BIP_RANGE(1.25),
> BIP_RANGE(0.625),
> UNI_RANGE(10),
> UNI_RANGE(5),
> UNI_RANGE(2.5),
> UNI_RANGE(1.25)
> }
> };
>
> static const comedi_lrange range_pci9118hg = { 8, {
> BIP_RANGE(5),
> BIP_RANGE(0.5),
> BIP_RANGE(0.05),
> BIP_RANGE(0.005),
> UNI_RANGE(10),
> UNI_RANGE(1),
> UNI_RANGE(0.1),
> UNI_RANGE(0.01)
> }
> };
>
> #define PCI9118_BIPOLAR_RANGES 4 /* used for test on mixture of BIP/UNI ranges */
>
> static int pci9118_attach(comedi_device * dev, comedi_devconfig * it);
> static int pci9118_detach(comedi_device * dev);
>
> typedef struct {
> const char *name; // board name
> int vendor_id; // PCI vendor a device ID of card
> int device_id;
> int iorange_amcc; // iorange for own S5933 region
> int iorange_9118; // pass thru card region size
> int n_aichan; // num of A/D chans
> int n_aichand; // num of A/D chans in diff mode
> int mux_aichan; // num of A/D chans with external multiplexor
> int n_aichanlist; // len of chanlist
> int n_aochan; // num of D/A chans
> int ai_maxdata; // resolution of A/D
> int ao_maxdata; // resolution of D/A
> const comedi_lrange *rangelist_ai; // rangelist for A/D
> const comedi_lrange *rangelist_ao; // rangelist for D/A
> unsigned int ai_ns_min; // max sample speed of card v ns
> unsigned int ai_pacer_min; // minimal pacer value (c1*c2 or c1 in burst)
> int half_fifo_size; // size of FIFO/2
>
> } boardtype;
>
> static DEFINE_PCI_DEVICE_TABLE(pci9118_pci_table) = {
> {PCI_VENDOR_ID_AMCC, 0x80d9, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
> {0}
> };
>
> MODULE_DEVICE_TABLE(pci, pci9118_pci_table);
>
> static const boardtype boardtypes[] = {
> {"pci9118dg", PCI_VENDOR_ID_AMCC, 0x80d9,
> AMCC_OP_REG_SIZE, IORANGE_9118,
> 16, 8, 256, PCI9118_CHANLEN, 2, 0x0fff, 0x0fff,
> &range_pci9118dg_hr, &range_bipolar10,
> 3000, 12, 512},
> {"pci9118hg", PCI_VENDOR_ID_AMCC, 0x80d9,
> AMCC_OP_REG_SIZE, IORANGE_9118,
> 16, 8, 256, PCI9118_CHANLEN, 2, 0x0fff, 0x0fff,
> &range_pci9118hg, &range_bipolar10,
> 3000, 12, 512},
> {"pci9118hr", PCI_VENDOR_ID_AMCC, 0x80d9,
> AMCC_OP_REG_SIZE, IORANGE_9118,
> 16, 8, 256, PCI9118_CHANLEN, 2, 0xffff, 0x0fff,
> &range_pci9118dg_hr, &range_bipolar10,
> 10000, 40, 512},
> };
>
> #define n_boardtypes (sizeof(boardtypes)/sizeof(boardtype))
>
> static comedi_driver driver_pci9118 = {
> driver_name:"adl_pci9118",
> module:THIS_MODULE,
> attach:pci9118_attach,
> detach:pci9118_detach,
> num_names:n_boardtypes,
> board_name:&boardtypes[0].name,
> offset:sizeof(boardtype),
> };
>
> COMEDI_PCI_INITCLEANUP(driver_pci9118, pci9118_pci_table);
>
> typedef struct {
> unsigned long iobase_a; // base+size for AMCC chip
> unsigned int master; // master capable
> struct pci_dev *pcidev; // ptr to actual pcidev
> unsigned int usemux; // we want to use external multiplexor!
> #ifdef PCI9118_PARANOIDCHECK
> unsigned short chanlist[PCI9118_CHANLEN + 1]; // list of scaned channel
> unsigned char chanlistlen; // number of scanlist
> #endif
> unsigned char AdControlReg; // A/D control register
> unsigned char IntControlReg; // Interrupt control register
> unsigned char AdFunctionReg; // A/D function register
> char valid; // driver is ok
> char ai_neverending; // we do unlimited AI
> unsigned int i8254_osc_base; // frequence of onboard oscilator
> unsigned int ai_do; // what do AI? 0=nothing, 1 to 4 mode
> unsigned int ai_act_scan; // how many scans we finished
> unsigned int ai_buf_ptr; // data buffer ptr in samples
> unsigned int ai_n_chan; // how many channels is measured
> unsigned int ai_n_scanlen; // len of actual scanlist
> unsigned int ai_n_realscanlen; // what we must transfer for one outgoing scan include front/back adds
> unsigned int ai_act_dmapos; // position in actual real stream
> unsigned int ai_add_front; // how many channels we must add before scan to satisfy S&H?
> unsigned int ai_add_back; // how many channels we must add before scan to satisfy DMA?
> unsigned int *ai_chanlist; // actaul chanlist
> unsigned int ai_timer1;
> unsigned int ai_timer2;
> unsigned int ai_flags;
> char ai12_startstop; // measure can start/stop on external trigger
> unsigned int ai_divisor1, ai_divisor2; // divisors for start of measure on external start
> unsigned int ai_data_len;
> sampl_t *ai_data;
> sampl_t ao_data[2]; // data output buffer
> unsigned int ai_scans; // number of scans to do
> char dma_doublebuf; // we can use double buffring
> unsigned int dma_actbuf; // which buffer is used now
> sampl_t *dmabuf_virt[2]; // pointers to begin of DMA buffer
> unsigned long dmabuf_hw[2]; // hw address of DMA buff
> unsigned int dmabuf_size[2]; // size of dma buffer in bytes
> unsigned int dmabuf_use_size[2]; // which size we may now used for transfer
> unsigned int dmabuf_used_size[2]; // which size was trully used
> unsigned int dmabuf_panic_size[2];
> unsigned int dmabuf_samples[2]; // size in samples
> int dmabuf_pages[2]; // number of pages in buffer
> unsigned char cnt0_users; // bit field of 8254 CNT0 users (0-unused, 1-AO, 2-DI, 3-DO)
> unsigned char exttrg_users; // bit field of external trigger users (0-AI, 1-AO, 2-DI, 3-DO)
> unsigned int cnt0_divisor; // actual CNT0 divisor
> void (*int_ai_func) (comedi_device *, comedi_subdevice *, unsigned short, unsigned int, unsigned short); // ptr to actual interrupt AI function
> unsigned char ai16bits; // =1 16 bit card
> unsigned char usedma; // =1 use DMA transfer and not INT
> unsigned char useeoshandle; // =1 change WAKE_EOS DMA transfer to fit on every second
> unsigned char usessh; // =1 turn on S&H support
> int softsshdelay; // >0 use software S&H, numer is requested delay in ns
> unsigned char softsshsample; // polarity of S&H signal in sample state
> unsigned char softsshhold; // polarity of S&H signal in hold state
> unsigned int ai_maskerr; // which warning was printed
> unsigned int ai_maskharderr; // on which error bits stops
> unsigned int ai_inttrig_start; // TRIG_INT for start
> } pci9118_private;
>
> #define devpriv ((pci9118_private *)dev->private)
> #define this_board ((boardtype *)dev->board_ptr)
>
> /*
> ==============================================================================
> */
>
> static int check_channel_list(comedi_device * dev, comedi_subdevice * s,
> int n_chan, unsigned int *chanlist, int frontadd, int backadd);
> static int setup_channel_list(comedi_device * dev, comedi_subdevice * s,
> int n_chan, unsigned int *chanlist, int rot, int frontadd, int backadd,
> int usedma, char eoshandle);
> static void start_pacer(comedi_device * dev, int mode, unsigned int divisor1,
> unsigned int divisor2);
> static int pci9118_reset(comedi_device * dev);
> static int pci9118_exttrg_add(comedi_device * dev, unsigned char source);
> static int pci9118_exttrg_del(comedi_device * dev, unsigned char source);
> static int pci9118_ai_cancel(comedi_device * dev, comedi_subdevice * s);
> static void pci9118_calc_divisors(char mode, comedi_device * dev,
> comedi_subdevice * s, unsigned int *tim1, unsigned int *tim2,
> unsigned int flags, int chans, unsigned int *div1, unsigned int *div2,
> char usessh, unsigned int chnsshfront);
>
> /*
> ==============================================================================
> */
> static int pci9118_insn_read_ai(comedi_device * dev, comedi_subdevice * s,
> comedi_insn * insn, lsampl_t * data)
> {
>
> int n, timeout;
>
> devpriv->AdControlReg = AdControl_Int & 0xff;
> devpriv->AdFunctionReg = AdFunction_PDTrg | AdFunction_PETrg;
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC); // positive triggers, no S&H, no burst, burst stop, no post trigger, no about trigger, trigger stop
>
> if (!setup_channel_list(dev, s, 1, &insn->chanspec, 0, 0, 0, 0, 0))
> return -EINVAL;
>
> outl(0, dev->iobase + PCI9118_DELFIFO); // flush FIFO
>
> for (n = 0; n < insn->n; n++) {
> outw(0, dev->iobase + PCI9118_SOFTTRG); /* start conversion */
> comedi_udelay(2);
> timeout = 100;
> while (timeout--) {
> if (inl(dev->iobase + PCI9118_ADSTAT) & AdStatus_ADrdy)
> goto conv_finish;
> comedi_udelay(1);
> }
>
> comedi_error(dev, "A/D insn timeout");
> data[n] = 0;
> outl(0, dev->iobase + PCI9118_DELFIFO); // flush FIFO
> return -ETIME;
>
> conv_finish:
> if (devpriv->ai16bits) {
> data[n] =
> (inl(dev->iobase +
> PCI9118_AD_DATA) & 0xffff) ^ 0x8000;
> } else {
> data[n] =
> (inw(dev->iobase +
> PCI9118_AD_DATA) >> 4) & 0xfff;
> }
> }
>
> outl(0, dev->iobase + PCI9118_DELFIFO); // flush FIFO
> return n;
>
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_insn_write_ao(comedi_device * dev, comedi_subdevice * s,
> comedi_insn * insn, lsampl_t * data)
> {
> int n, chanreg, ch;
>
> ch = CR_CHAN(insn->chanspec);
> if (ch) {
> chanreg = PCI9118_DA2;
> } else {
> chanreg = PCI9118_DA1;
> }
>
> for (n = 0; n < insn->n; n++) {
> outl(data[n], dev->iobase + chanreg);
> devpriv->ao_data[ch] = data[n];
> }
>
> return n;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_insn_read_ao(comedi_device * dev, comedi_subdevice * s,
> comedi_insn * insn, lsampl_t * data)
> {
> int n, chan;
>
> chan = CR_CHAN(insn->chanspec);
> for (n = 0; n < insn->n; n++)
> data[n] = devpriv->ao_data[chan];
>
> return n;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_insn_bits_di(comedi_device * dev, comedi_subdevice * s,
> comedi_insn * insn, lsampl_t * data)
> {
> data[1] = inl(dev->iobase + PCI9118_DI) & 0xf;
>
> return 2;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_insn_bits_do(comedi_device * dev, comedi_subdevice * s,
> comedi_insn * insn, lsampl_t * data)
> {
> if (data[0]) {
> s->state &= ~data[0];
> s->state |= (data[0] & data[1]);
> outl(s->state & 0x0f, dev->iobase + PCI9118_DO);
> }
> data[1] = s->state;
>
> return 2;
> }
>
> /*
> ==============================================================================
> */
> static void interrupt_pci9118_ai_mode4_switch(comedi_device * dev)
> {
> devpriv->AdFunctionReg =
> AdFunction_PDTrg | AdFunction_PETrg | AdFunction_AM;
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC);
> outl(0x30, dev->iobase + PCI9118_CNTCTRL);
> outl((devpriv->dmabuf_hw[1 - devpriv->dma_actbuf] >> 1) & 0xff,
> dev->iobase + PCI9118_CNT0);
> outl((devpriv->dmabuf_hw[1 - devpriv->dma_actbuf] >> 9) & 0xff,
> dev->iobase + PCI9118_CNT0);
> devpriv->AdFunctionReg |= AdFunction_Start;
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC);
> }
>
> static unsigned int defragment_dma_buffer(comedi_device * dev,
> comedi_subdevice * s, sampl_t * dma_buffer, unsigned int num_samples)
> {
> unsigned int i = 0, j = 0;
> unsigned int start_pos = devpriv->ai_add_front,
> stop_pos = devpriv->ai_add_front + devpriv->ai_n_chan;
> unsigned int raw_scanlen = devpriv->ai_add_front + devpriv->ai_n_chan +
> devpriv->ai_add_back;
>
> for (i = 0; i < num_samples; i++) {
> if (devpriv->ai_act_dmapos >= start_pos &&
> devpriv->ai_act_dmapos < stop_pos) {
> dma_buffer[j++] = dma_buffer[i];
> }
> devpriv->ai_act_dmapos++;
> devpriv->ai_act_dmapos %= raw_scanlen;
> }
>
> return j;
> }
>
> /*
> ==============================================================================
> */
> static unsigned int move_block_from_dma(comedi_device * dev,
> comedi_subdevice * s, sampl_t * dma_buffer, unsigned int num_samples)
> {
> unsigned int num_bytes;
>
> num_samples = defragment_dma_buffer(dev, s, dma_buffer, num_samples);
> devpriv->ai_act_scan +=
> (s->async->cur_chan + num_samples) / devpriv->ai_n_scanlen;
> s->async->cur_chan += num_samples;
> s->async->cur_chan %= devpriv->ai_n_scanlen;
> num_bytes =
> cfc_write_array_to_buffer(s, dma_buffer,
> num_samples * sizeof(sampl_t));
> if (num_bytes < num_samples * sizeof(sampl_t))
> return -1;
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static char pci9118_decode_error_status(comedi_device * dev,
> comedi_subdevice * s, unsigned char m)
> {
> if (m & 0x100) {
> comedi_error(dev, "A/D FIFO Full status (Fatal Error!)");
> devpriv->ai_maskerr &= ~0x100L;
> }
> if (m & 0x008) {
> comedi_error(dev,
> "A/D Burst Mode Overrun Status (Fatal Error!)");
> devpriv->ai_maskerr &= ~0x008L;
> }
> if (m & 0x004) {
> comedi_error(dev, "A/D Over Speed Status (Warning!)");
> devpriv->ai_maskerr &= ~0x004L;
> }
> if (m & 0x002) {
> comedi_error(dev, "A/D Overrun Status (Fatal Error!)");
> devpriv->ai_maskerr &= ~0x002L;
> }
> if (m & devpriv->ai_maskharderr) {
> s->async->events |= COMEDI_CB_ERROR | COMEDI_CB_EOA;
> pci9118_ai_cancel(dev, s);
> comedi_event(dev, s);
> return 1;
> }
>
> return 0;
> }
>
> static void pci9118_ai_munge(comedi_device * dev, comedi_subdevice * s,
> void *data, unsigned int num_bytes, unsigned int start_chan_index)
> {
> unsigned int i, num_samples = num_bytes / sizeof(sampl_t);
> sampl_t *array = data;
>
> for (i = 0; i < num_samples; i++) {
> if (devpriv->usedma)
> array[i] = be16_to_cpu(array[i]);
> if (devpriv->ai16bits) {
> array[i] ^= 0x8000;
> } else {
> array[i] = (array[i] >> 4) & 0x0fff;
> }
> }
> }
>
> /*
> ==============================================================================
> */
> static void interrupt_pci9118_ai_onesample(comedi_device * dev,
> comedi_subdevice * s, unsigned short int_adstat, unsigned int int_amcc,
> unsigned short int_daq)
> {
> register sampl_t sampl;
>
> s->async->events = 0;
>
> if (int_adstat & devpriv->ai_maskerr)
> if (pci9118_decode_error_status(dev, s, int_adstat))
> return;
>
> sampl = inw(dev->iobase + PCI9118_AD_DATA);
>
> #ifdef PCI9118_PARANOIDCHECK
> if (devpriv->ai16bits == 0) {
> if ((sampl & 0x000f) != devpriv->chanlist[s->async->cur_chan]) { // data dropout!
> rt_printk
> ("comedi: A/D SAMPL - data dropout: received channel %d, expected %d!\n",
> sampl & 0x000f,
> devpriv->chanlist[s->async->cur_chan]);
> s->async->events |= COMEDI_CB_ERROR | COMEDI_CB_EOA;
> pci9118_ai_cancel(dev, s);
> comedi_event(dev, s);
> return;
> }
> }
> #endif
> cfc_write_to_buffer(s, sampl);
> s->async->cur_chan++;
> if (s->async->cur_chan >= devpriv->ai_n_scanlen) { /* one scan done */
> s->async->cur_chan %= devpriv->ai_n_scanlen;
> devpriv->ai_act_scan++;
> if (!(devpriv->ai_neverending))
> if (devpriv->ai_act_scan >= devpriv->ai_scans) { /* all data sampled */
> pci9118_ai_cancel(dev, s);
> s->async->events |= COMEDI_CB_EOA;
> }
> }
>
> if (s->async->events)
> comedi_event(dev, s);
> }
>
> /*
> ==============================================================================
> */
> static void interrupt_pci9118_ai_dma(comedi_device * dev, comedi_subdevice * s,
> unsigned short int_adstat, unsigned int int_amcc,
> unsigned short int_daq)
> {
> unsigned int next_dma_buf, samplesinbuf, sampls, m;
>
> if (int_amcc & MASTER_ABORT_INT) {
> comedi_error(dev, "AMCC IRQ - MASTER DMA ABORT!");
> s->async->events |= COMEDI_CB_ERROR | COMEDI_CB_EOA;
> pci9118_ai_cancel(dev, s);
> comedi_event(dev, s);
> return;
> }
>
> if (int_amcc & TARGET_ABORT_INT) {
> comedi_error(dev, "AMCC IRQ - TARGET DMA ABORT!");
> s->async->events |= COMEDI_CB_ERROR | COMEDI_CB_EOA;
> pci9118_ai_cancel(dev, s);
> comedi_event(dev, s);
> return;
> }
>
> if (int_adstat & devpriv->ai_maskerr)
> // if (int_adstat & 0x106)
> if (pci9118_decode_error_status(dev, s, int_adstat))
> return;
>
> samplesinbuf = devpriv->dmabuf_use_size[devpriv->dma_actbuf] >> 1; // number of received real samples
> // DPRINTK("dma_actbuf=%d\n",devpriv->dma_actbuf);
>
> if (devpriv->dma_doublebuf) { // switch DMA buffers if is used double buffering
> next_dma_buf = 1 - devpriv->dma_actbuf;
> outl(devpriv->dmabuf_hw[next_dma_buf],
> devpriv->iobase_a + AMCC_OP_REG_MWAR);
> outl(devpriv->dmabuf_use_size[next_dma_buf],
> devpriv->iobase_a + AMCC_OP_REG_MWTC);
> devpriv->dmabuf_used_size[next_dma_buf] =
> devpriv->dmabuf_use_size[next_dma_buf];
> if (devpriv->ai_do == 4)
> interrupt_pci9118_ai_mode4_switch(dev);
> }
>
> if (samplesinbuf) {
> m = devpriv->ai_data_len >> 1; // how many samples is to end of buffer
> // DPRINTK("samps=%d m=%d %d %d\n",samplesinbuf,m,s->async->buf_int_count,s->async->buf_int_ptr);
> sampls = m;
> move_block_from_dma(dev, s,
> devpriv->dmabuf_virt[devpriv->dma_actbuf],
> samplesinbuf);
> m = m - sampls; // m= how many samples was transfered
> }
> // DPRINTK("YYY\n");
>
> if (!devpriv->ai_neverending)
> if (devpriv->ai_act_scan >= devpriv->ai_scans) { /* all data sampled */
> pci9118_ai_cancel(dev, s);
> s->async->events |= COMEDI_CB_EOA;
> }
>
> if (devpriv->dma_doublebuf) { // switch dma buffers
> devpriv->dma_actbuf = 1 - devpriv->dma_actbuf;
> } else { // restart DMA if is not used double buffering
> outl(devpriv->dmabuf_hw[0],
> devpriv->iobase_a + AMCC_OP_REG_MWAR);
> outl(devpriv->dmabuf_use_size[0],
> devpriv->iobase_a + AMCC_OP_REG_MWTC);
> if (devpriv->ai_do == 4)
> interrupt_pci9118_ai_mode4_switch(dev);
> }
>
> comedi_event(dev, s);
> }
>
> /*
> ==============================================================================
> */
> static irqreturn_t interrupt_pci9118(int irq, void *d PT_REGS_ARG)
> {
> comedi_device *dev = d;
> unsigned int int_daq = 0, int_amcc, int_adstat;
>
> if (!dev->attached)
> return IRQ_NONE; // not fully initialized
>
> int_daq = inl(dev->iobase + PCI9118_INTSRC) & 0xf; // get IRQ reasons from card
> int_amcc = inl(devpriv->iobase_a + AMCC_OP_REG_INTCSR); // get INT register from AMCC chip
>
> // DPRINTK("INT daq=0x%01x amcc=0x%08x MWAR=0x%08x MWTC=0x%08x ADSTAT=0x%02x ai_do=%d\n", int_daq, int_amcc, inl(devpriv->iobase_a+AMCC_OP_REG_MWAR), inl(devpriv->iobase_a+AMCC_OP_REG_MWTC), inw(dev->iobase+PCI9118_ADSTAT)&0x1ff,devpriv->ai_do);
>
> if ((!int_daq) && (!(int_amcc & ANY_S593X_INT)))
> return IRQ_NONE; // interrupt from other source
>
> outl(int_amcc | 0x00ff0000, devpriv->iobase_a + AMCC_OP_REG_INTCSR); // shutdown IRQ reasons in AMCC
>
> int_adstat = inw(dev->iobase + PCI9118_ADSTAT) & 0x1ff; // get STATUS register
>
> if (devpriv->ai_do) {
> if (devpriv->ai12_startstop)
> if ((int_adstat & AdStatus_DTH) && (int_daq & Int_DTrg)) { // start stop of measure
> if (devpriv->ai12_startstop & START_AI_EXT) {
> devpriv->ai12_startstop &=
> ~START_AI_EXT;
> if (!(devpriv->ai12_startstop &
> STOP_AI_EXT))
> pci9118_exttrg_del(dev, EXTTRG_AI); // deactivate EXT trigger
> start_pacer(dev, devpriv->ai_do, devpriv->ai_divisor1, devpriv->ai_divisor2); // start pacer
> outl(devpriv->AdControlReg,
> dev->iobase + PCI9118_ADCNTRL);
> } else {
> if (devpriv->
> ai12_startstop & STOP_AI_EXT) {
> devpriv->ai12_startstop &=
> ~STOP_AI_EXT;
> pci9118_exttrg_del(dev, EXTTRG_AI); // deactivate EXT trigger
> devpriv->ai_neverending = 0; //well, on next interrupt from DMA/EOC measure will stop
> }
> }
> }
>
> (devpriv->int_ai_func) (dev, dev->subdevices + 0, int_adstat,
> int_amcc, int_daq);
>
> }
> return IRQ_HANDLED;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_ai_inttrig(comedi_device * dev, comedi_subdevice * s,
> unsigned int trignum)
> {
> if (trignum != devpriv->ai_inttrig_start)
> return -EINVAL;
>
> devpriv->ai12_startstop &= ~START_AI_INT;
> s->async->inttrig = NULL;
>
> outl(devpriv->IntControlReg, dev->iobase + PCI9118_INTCTRL);
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC);
> if (devpriv->ai_do != 3) {
> start_pacer(dev, devpriv->ai_do, devpriv->ai_divisor1,
> devpriv->ai_divisor2);
> devpriv->AdControlReg |= AdControl_SoftG;
> }
> outl(devpriv->AdControlReg, dev->iobase + PCI9118_ADCNTRL);
>
> return 1;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_ai_cmdtest(comedi_device * dev, comedi_subdevice * s,
> comedi_cmd * cmd)
> {
> int err = 0;
> int tmp, divisor1 = 0, divisor2 = 0;
>
> /* step 1: make sure trigger sources are trivially valid */
>
> tmp = cmd->start_src;
> cmd->start_src &= TRIG_NOW | TRIG_EXT | TRIG_INT;
> if (!cmd->start_src || tmp != cmd->start_src)
> err++;
>
> tmp = cmd->scan_begin_src;
> if (devpriv->master) {
> cmd->scan_begin_src &= TRIG_TIMER | TRIG_EXT | TRIG_FOLLOW;
> } else {
> cmd->scan_begin_src &= TRIG_FOLLOW;
> }
> if (!cmd->scan_begin_src || tmp != cmd->scan_begin_src)
> err++;
>
> tmp = cmd->convert_src;
> if (devpriv->master) {
> cmd->convert_src &= TRIG_TIMER | TRIG_EXT | TRIG_NOW;
> } else {
> cmd->convert_src &= TRIG_TIMER | TRIG_EXT;
> }
> if (!cmd->convert_src || tmp != cmd->convert_src)
> err++;
>
> tmp = cmd->scan_end_src;
> cmd->scan_end_src &= TRIG_COUNT;
> if (!cmd->scan_end_src || tmp != cmd->scan_end_src)
> err++;
>
> tmp = cmd->stop_src;
> cmd->stop_src &= TRIG_COUNT | TRIG_NONE | TRIG_EXT;
> if (!cmd->stop_src || tmp != cmd->stop_src)
> err++;
>
> if (err)
> return 1;
>
> /* step 2: make sure trigger sources are unique and mutually compatible */
>
> if (cmd->start_src != TRIG_NOW &&
> cmd->start_src != TRIG_INT && cmd->start_src != TRIG_EXT) {
> cmd->start_src = TRIG_NOW;
> err++;
> }
>
> if (cmd->scan_begin_src != TRIG_TIMER &&
> cmd->scan_begin_src != TRIG_EXT &&
> cmd->scan_begin_src != TRIG_INT &&
> cmd->scan_begin_src != TRIG_FOLLOW) {
> cmd->scan_begin_src = TRIG_FOLLOW;
> err++;
> }
>
> if (cmd->convert_src != TRIG_TIMER &&
> cmd->convert_src != TRIG_EXT && cmd->convert_src != TRIG_NOW) {
> cmd->convert_src = TRIG_TIMER;
> err++;
> }
>
> if (cmd->scan_end_src != TRIG_COUNT) {
> cmd->scan_end_src = TRIG_COUNT;
> err++;
> }
>
> if (cmd->stop_src != TRIG_NONE &&
> cmd->stop_src != TRIG_COUNT &&
> cmd->stop_src != TRIG_INT && cmd->stop_src != TRIG_EXT) {
> cmd->stop_src = TRIG_COUNT;
> err++;
> }
>
> if (cmd->start_src == TRIG_EXT && cmd->scan_begin_src == TRIG_EXT) {
> cmd->start_src = TRIG_NOW;
> err++;
> }
>
> if (cmd->start_src == TRIG_INT && cmd->scan_begin_src == TRIG_INT) {
> cmd->start_src = TRIG_NOW;
> err++;
> }
>
> if ((cmd->scan_begin_src & (TRIG_TIMER | TRIG_EXT)) &&
> (!(cmd->convert_src & (TRIG_TIMER | TRIG_NOW)))) {
> cmd->convert_src = TRIG_TIMER;
> err++;
> }
>
> if ((cmd->scan_begin_src == TRIG_FOLLOW) &&
> (!(cmd->convert_src & (TRIG_TIMER | TRIG_EXT)))) {
> cmd->convert_src = TRIG_TIMER;
> err++;
> }
>
> if (cmd->stop_src == TRIG_EXT && cmd->scan_begin_src == TRIG_EXT) {
> cmd->stop_src = TRIG_COUNT;
> err++;
> }
>
> if (err)
> return 2;
>
> /* step 3: make sure arguments are trivially compatible */
>
> if (cmd->start_src & (TRIG_NOW | TRIG_EXT))
> if (cmd->start_arg != 0) {
> cmd->start_arg = 0;
> err++;
> }
>
> if (cmd->scan_begin_src & (TRIG_FOLLOW | TRIG_EXT))
> if (cmd->scan_begin_arg != 0) {
> cmd->scan_begin_arg = 0;
> err++;
> }
>
> if ((cmd->scan_begin_src == TRIG_TIMER) &&
> (cmd->convert_src == TRIG_TIMER) && (cmd->scan_end_arg == 1)) {
> cmd->scan_begin_src = TRIG_FOLLOW;
> cmd->convert_arg = cmd->scan_begin_arg;
> cmd->scan_begin_arg = 0;
> }
>
> if (cmd->scan_begin_src == TRIG_TIMER)
> if (cmd->scan_begin_arg < this_board->ai_ns_min) {
> cmd->scan_begin_arg = this_board->ai_ns_min;
> err++;
> }
>
> if (cmd->scan_begin_src == TRIG_EXT)
> if (cmd->scan_begin_arg) {
> cmd->scan_begin_arg = 0;
> err++;
> if (cmd->scan_end_arg > 65535) {
> cmd->scan_end_arg = 65535;
> err++;
> }
> }
>
> if (cmd->convert_src & (TRIG_TIMER | TRIG_NOW))
> if (cmd->convert_arg < this_board->ai_ns_min) {
> cmd->convert_arg = this_board->ai_ns_min;
> err++;
> }
>
> if (cmd->convert_src == TRIG_EXT)
> if (cmd->convert_arg) {
> cmd->convert_arg = 0;
> err++;
> }
>
> if (cmd->stop_src == TRIG_COUNT) {
> if (!cmd->stop_arg) {
> cmd->stop_arg = 1;
> err++;
> }
> } else { /* TRIG_NONE */
> if (cmd->stop_arg != 0) {
> cmd->stop_arg = 0;
> err++;
> }
> }
>
> if (!cmd->chanlist_len) {
> cmd->chanlist_len = 1;
> err++;
> }
>
> if (cmd->chanlist_len > this_board->n_aichanlist) {
> cmd->chanlist_len = this_board->n_aichanlist;
> err++;
> }
>
> if (cmd->scan_end_arg < cmd->chanlist_len) {
> cmd->scan_end_arg = cmd->chanlist_len;
> err++;
> }
>
> if ((cmd->scan_end_arg % cmd->chanlist_len)) {
> cmd->scan_end_arg =
> cmd->chanlist_len * (cmd->scan_end_arg /
> cmd->chanlist_len);
> err++;
> }
>
> if (err)
> return 3;
>
> /* step 4: fix up any arguments */
>
> if (cmd->scan_begin_src == TRIG_TIMER) {
> tmp = cmd->scan_begin_arg;
> // rt_printk("S1 timer1=%u timer2=%u\n",cmd->scan_begin_arg,cmd->convert_arg);
> i8253_cascade_ns_to_timer(devpriv->i8254_osc_base, &divisor1,
> &divisor2, &cmd->scan_begin_arg,
> cmd->flags & TRIG_ROUND_MASK);
> // rt_printk("S2 timer1=%u timer2=%u\n",cmd->scan_begin_arg,cmd->convert_arg);
> if (cmd->scan_begin_arg < this_board->ai_ns_min)
> cmd->scan_begin_arg = this_board->ai_ns_min;
> if (tmp != cmd->scan_begin_arg)
> err++;
> }
>
> if (cmd->convert_src & (TRIG_TIMER | TRIG_NOW)) {
> tmp = cmd->convert_arg;
> i8253_cascade_ns_to_timer(devpriv->i8254_osc_base, &divisor1,
> &divisor2, &cmd->convert_arg,
> cmd->flags & TRIG_ROUND_MASK);
> // rt_printk("s1 timer1=%u timer2=%u\n",cmd->scan_begin_arg,cmd->convert_arg);
> if (cmd->convert_arg < this_board->ai_ns_min)
> cmd->convert_arg = this_board->ai_ns_min;
> if (tmp != cmd->convert_arg)
> err++;
> if (cmd->scan_begin_src == TRIG_TIMER
> && cmd->convert_src == TRIG_NOW) {
> if (cmd->convert_arg == 0) {
> if (cmd->scan_begin_arg <
> this_board->ai_ns_min *
> (cmd->scan_end_arg + 2)) {
> cmd->scan_begin_arg =
> this_board->ai_ns_min *
> (cmd->scan_end_arg + 2);
> // rt_printk("s2 timer1=%u timer2=%u\n",cmd->scan_begin_arg,cmd->convert_arg);
> err++;
> }
> } else {
> if (cmd->scan_begin_arg <
> cmd->convert_arg * cmd->chanlist_len) {
> cmd->scan_begin_arg =
> cmd->convert_arg *
> cmd->chanlist_len;
> // rt_printk("s3 timer1=%u timer2=%u\n",cmd->scan_begin_arg,cmd->convert_arg);
> err++;
> }
> }
> }
> }
>
> if (err)
> return 4;
>
> if (cmd->chanlist)
> if (!check_channel_list(dev, s, cmd->chanlist_len,
> cmd->chanlist, 0, 0))
> return 5; // incorrect channels list
>
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int Compute_and_setup_dma(comedi_device * dev)
> {
> unsigned int dmalen0, dmalen1, i;
>
> DPRINTK("adl_pci9118 EDBG: BGN: Compute_and_setup_dma()\n");
> dmalen0 = devpriv->dmabuf_size[0];
> dmalen1 = devpriv->dmabuf_size[1];
> DPRINTK("1 dmalen0=%d dmalen1=%d ai_data_len=%d\n", dmalen0, dmalen1,
> devpriv->ai_data_len);
> // isn't output buff smaller that our DMA buff?
> if (dmalen0 > (devpriv->ai_data_len)) {
> dmalen0 = devpriv->ai_data_len & ~3L; // allign to 32bit down
> }
> if (dmalen1 > (devpriv->ai_data_len)) {
> dmalen1 = devpriv->ai_data_len & ~3L; // allign to 32bit down
> }
> DPRINTK("2 dmalen0=%d dmalen1=%d \n", dmalen0, dmalen1);
>
> // we want wake up every scan?
> if (devpriv->ai_flags & TRIG_WAKE_EOS) {
> if (dmalen0 < (devpriv->ai_n_realscanlen << 1)) {
> // uff, too short DMA buffer, disable EOS support!
> devpriv->ai_flags &= (~TRIG_WAKE_EOS);
> rt_printk
> ("comedi%d: WAR: DMA0 buf too short, cann't support TRIG_WAKE_EOS (%d<%d)\n",
> dev->minor, dmalen0,
> devpriv->ai_n_realscanlen << 1);
> } else {
> // short first DMA buffer to one scan
> dmalen0 = devpriv->ai_n_realscanlen << 1;
> DPRINTK("21 dmalen0=%d ai_n_realscanlen=%d useeoshandle=%d\n", dmalen0, devpriv->ai_n_realscanlen, devpriv->useeoshandle);
> if (devpriv->useeoshandle)
> dmalen0 += 2;
> if (dmalen0 < 4) {
> rt_printk
> ("comedi%d: ERR: DMA0 buf len bug? (%d<4)\n",
> dev->minor, dmalen0);
> dmalen0 = 4;
> }
> }
> }
> if (devpriv->ai_flags & TRIG_WAKE_EOS) {
> if (dmalen1 < (devpriv->ai_n_realscanlen << 1)) {
> // uff, too short DMA buffer, disable EOS support!
> devpriv->ai_flags &= (~TRIG_WAKE_EOS);
> rt_printk
> ("comedi%d: WAR: DMA1 buf too short, cann't support TRIG_WAKE_EOS (%d<%d)\n",
> dev->minor, dmalen1,
> devpriv->ai_n_realscanlen << 1);
> } else {
> // short second DMA buffer to one scan
> dmalen1 = devpriv->ai_n_realscanlen << 1;
> DPRINTK("22 dmalen1=%d ai_n_realscanlen=%d useeoshandle=%d\n", dmalen1, devpriv->ai_n_realscanlen, devpriv->useeoshandle);
> if (devpriv->useeoshandle)
> dmalen1 -= 2;
> if (dmalen1 < 4) {
> rt_printk
> ("comedi%d: ERR: DMA1 buf len bug? (%d<4)\n",
> dev->minor, dmalen1);
> dmalen1 = 4;
> }
> }
> }
>
> DPRINTK("3 dmalen0=%d dmalen1=%d \n", dmalen0, dmalen1);
> // transfer without TRIG_WAKE_EOS
> if (!(devpriv->ai_flags & TRIG_WAKE_EOS)) {
> // if it's possible then allign DMA buffers to length of scan
> i = dmalen0;
> dmalen0 =
> (dmalen0 / (devpriv->ai_n_realscanlen << 1)) *
> (devpriv->ai_n_realscanlen << 1);
> dmalen0 &= ~3L;
> if (!dmalen0)
> dmalen0 = i; // uff. very long scan?
> i = dmalen1;
> dmalen1 =
> (dmalen1 / (devpriv->ai_n_realscanlen << 1)) *
> (devpriv->ai_n_realscanlen << 1);
> dmalen1 &= ~3L;
> if (!dmalen1)
> dmalen1 = i; // uff. very long scan?
> // if measure isn't neverending then test, if it whole fits into one or two DMA buffers
> if (!devpriv->ai_neverending) {
> // fits whole measure into one DMA buffer?
> if (dmalen0 >
> ((devpriv->ai_n_realscanlen << 1) *
> devpriv->ai_scans)) {
> DPRINTK("3.0 ai_n_realscanlen=%d ai_scans=%d \n", devpriv->ai_n_realscanlen, devpriv->ai_scans);
> dmalen0 =
> (devpriv->ai_n_realscanlen << 1) *
> devpriv->ai_scans;
> DPRINTK("3.1 dmalen0=%d dmalen1=%d \n", dmalen0,
> dmalen1);
> dmalen0 &= ~3L;
> } else { // fits whole measure into two DMA buffer?
> if (dmalen1 >
> ((devpriv->ai_n_realscanlen << 1) *
> devpriv->ai_scans - dmalen0))
> dmalen1 =
> (devpriv->
> ai_n_realscanlen << 1) *
> devpriv->ai_scans - dmalen0;
> DPRINTK("3.2 dmalen0=%d dmalen1=%d \n", dmalen0,
> dmalen1);
> dmalen1 &= ~3L;
> }
> }
> }
>
> DPRINTK("4 dmalen0=%d dmalen1=%d \n", dmalen0, dmalen1);
>
> // these DMA buffer size we'll be used
> devpriv->dma_actbuf = 0;
> devpriv->dmabuf_use_size[0] = dmalen0;
> devpriv->dmabuf_use_size[1] = dmalen1;
>
> DPRINTK("5 dmalen0=%d dmalen1=%d \n", dmalen0, dmalen1);
> #if 0
> if (devpriv->ai_n_scanlen < this_board->half_fifo_size) {
> devpriv->dmabuf_panic_size[0] =
> (this_board->half_fifo_size / devpriv->ai_n_scanlen +
> 1) * devpriv->ai_n_scanlen * sizeof(sampl_t);
> devpriv->dmabuf_panic_size[1] =
> (this_board->half_fifo_size / devpriv->ai_n_scanlen +
> 1) * devpriv->ai_n_scanlen * sizeof(sampl_t);
> } else {
> devpriv->dmabuf_panic_size[0] =
> (devpriv->ai_n_scanlen << 1) % devpriv->dmabuf_size[0];
> devpriv->dmabuf_panic_size[1] =
> (devpriv->ai_n_scanlen << 1) % devpriv->dmabuf_size[1];
> }
> #endif
>
> outl(inl(devpriv->iobase_a + AMCC_OP_REG_MCSR) & (~EN_A2P_TRANSFERS), devpriv->iobase_a + AMCC_OP_REG_MCSR); // stop DMA
> outl(devpriv->dmabuf_hw[0], devpriv->iobase_a + AMCC_OP_REG_MWAR);
> outl(devpriv->dmabuf_use_size[0], devpriv->iobase_a + AMCC_OP_REG_MWTC);
> // init DMA transfer
> outl(0x00000000 | AINT_WRITE_COMPL,
> devpriv->iobase_a + AMCC_OP_REG_INTCSR);
> // outl(0x02000000|AINT_WRITE_COMPL, devpriv->iobase_a+AMCC_OP_REG_INTCSR);
>
> outl(inl(devpriv->iobase_a +
> AMCC_OP_REG_MCSR) | RESET_A2P_FLAGS | A2P_HI_PRIORITY |
> EN_A2P_TRANSFERS, devpriv->iobase_a + AMCC_OP_REG_MCSR);
> outl(inl(devpriv->iobase_a + AMCC_OP_REG_INTCSR) | EN_A2P_TRANSFERS, devpriv->iobase_a + AMCC_OP_REG_INTCSR); // allow bus mastering
>
> DPRINTK("adl_pci9118 EDBG: END: Compute_and_setup_dma()\n");
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_ai_docmd_sampl(comedi_device * dev, comedi_subdevice * s)
> {
> DPRINTK("adl_pci9118 EDBG: BGN: pci9118_ai_docmd_sampl(%d,) [%d]\n",
> dev->minor, devpriv->ai_do);
> switch (devpriv->ai_do) {
> case 1:
> devpriv->AdControlReg |= AdControl_TmrTr;
> break;
> case 2:
> comedi_error(dev, "pci9118_ai_docmd_sampl() mode 2 bug!\n");
> return -EIO;
> case 3:
> devpriv->AdControlReg |= AdControl_ExtM;
> break;
> case 4:
> comedi_error(dev, "pci9118_ai_docmd_sampl() mode 4 bug!\n");
> return -EIO;
> default:
> comedi_error(dev,
> "pci9118_ai_docmd_sampl() mode number bug!\n");
> return -EIO;
> };
>
> devpriv->int_ai_func = interrupt_pci9118_ai_onesample; //transfer function
>
> if (devpriv->ai12_startstop)
> pci9118_exttrg_add(dev, EXTTRG_AI); // activate EXT trigger
>
> if ((devpriv->ai_do == 1) || (devpriv->ai_do == 2))
> devpriv->IntControlReg |= Int_Timer;
>
> devpriv->AdControlReg |= AdControl_Int;
>
> outl(inl(devpriv->iobase_a + AMCC_OP_REG_INTCSR) | 0x1f00, devpriv->iobase_a + AMCC_OP_REG_INTCSR); // allow INT in AMCC
>
> if (!(devpriv->ai12_startstop & (START_AI_EXT | START_AI_INT))) {
> outl(devpriv->IntControlReg, dev->iobase + PCI9118_INTCTRL);
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC);
> if (devpriv->ai_do != 3) {
> start_pacer(dev, devpriv->ai_do, devpriv->ai_divisor1,
> devpriv->ai_divisor2);
> devpriv->AdControlReg |= AdControl_SoftG;
> }
> outl(devpriv->IntControlReg, dev->iobase + PCI9118_INTCTRL);
> }
>
> DPRINTK("adl_pci9118 EDBG: END: pci9118_ai_docmd_sampl()\n");
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_ai_docmd_dma(comedi_device * dev, comedi_subdevice * s)
> {
> DPRINTK("adl_pci9118 EDBG: BGN: pci9118_ai_docmd_dma(%d,) [%d,%d]\n",
> dev->minor, devpriv->ai_do, devpriv->usedma);
> Compute_and_setup_dma(dev);
>
> switch (devpriv->ai_do) {
> case 1:
> devpriv->AdControlReg |=
> ((AdControl_TmrTr | AdControl_Dma) & 0xff);
> break;
> case 2:
> devpriv->AdControlReg |=
> ((AdControl_TmrTr | AdControl_Dma) & 0xff);
> devpriv->AdFunctionReg =
> AdFunction_PDTrg | AdFunction_PETrg | AdFunction_BM |
> AdFunction_BS;
> if (devpriv->usessh && (!devpriv->softsshdelay))
> devpriv->AdFunctionReg |= AdFunction_BSSH;
> outl(devpriv->ai_n_realscanlen, dev->iobase + PCI9118_BURST);
> break;
> case 3:
> devpriv->AdControlReg |=
> ((AdControl_ExtM | AdControl_Dma) & 0xff);
> devpriv->AdFunctionReg = AdFunction_PDTrg | AdFunction_PETrg;
> break;
> case 4:
> devpriv->AdControlReg |=
> ((AdControl_TmrTr | AdControl_Dma) & 0xff);
> devpriv->AdFunctionReg =
> AdFunction_PDTrg | AdFunction_PETrg | AdFunction_AM;
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC);
> outl(0x30, dev->iobase + PCI9118_CNTCTRL);
> outl((devpriv->dmabuf_hw[0] >> 1) & 0xff,
> dev->iobase + PCI9118_CNT0);
> outl((devpriv->dmabuf_hw[0] >> 9) & 0xff,
> dev->iobase + PCI9118_CNT0);
> devpriv->AdFunctionReg |= AdFunction_Start;
> break;
> default:
> comedi_error(dev, "pci9118_ai_docmd_dma() mode number bug!\n");
> return -EIO;
> };
>
> if (devpriv->ai12_startstop) {
> pci9118_exttrg_add(dev, EXTTRG_AI); // activate EXT trigger
> }
>
> devpriv->int_ai_func = interrupt_pci9118_ai_dma; //transfer function
>
> outl(0x02000000 | AINT_WRITE_COMPL,
> devpriv->iobase_a + AMCC_OP_REG_INTCSR);
>
> if (!(devpriv->ai12_startstop & (START_AI_EXT | START_AI_INT))) {
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC);
> outl(devpriv->IntControlReg, dev->iobase + PCI9118_INTCTRL);
> if (devpriv->ai_do != 3) {
> start_pacer(dev, devpriv->ai_do, devpriv->ai_divisor1,
> devpriv->ai_divisor2);
> devpriv->AdControlReg |= AdControl_SoftG;
> }
> outl(devpriv->AdControlReg, dev->iobase + PCI9118_ADCNTRL);
> }
>
> DPRINTK("adl_pci9118 EDBG: BGN: pci9118_ai_docmd_dma()\n");
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_ai_cmd(comedi_device * dev, comedi_subdevice * s)
> {
> comedi_cmd *cmd = &s->async->cmd;
> unsigned int addchans = 0;
> int ret = 0;
>
> DPRINTK("adl_pci9118 EDBG: BGN: pci9118_ai_cmd(%d,)\n", dev->minor);
> devpriv->ai12_startstop = 0;
> devpriv->ai_flags = cmd->flags;
> devpriv->ai_n_chan = cmd->chanlist_len;
> devpriv->ai_n_scanlen = cmd->scan_end_arg;
> devpriv->ai_chanlist = cmd->chanlist;
> devpriv->ai_data = s->async->prealloc_buf;
> devpriv->ai_data_len = s->async->prealloc_bufsz;
> devpriv->ai_timer1 = 0;
> devpriv->ai_timer2 = 0;
> devpriv->ai_add_front = 0;
> devpriv->ai_add_back = 0;
> devpriv->ai_maskerr = 0x10e;
>
> // prepare for start/stop conditions
> if (cmd->start_src == TRIG_EXT)
> devpriv->ai12_startstop |= START_AI_EXT;
> if (cmd->stop_src == TRIG_EXT) {
> devpriv->ai_neverending = 1;
> devpriv->ai12_startstop |= STOP_AI_EXT;
> }
> if (cmd->start_src == TRIG_INT) {
> devpriv->ai12_startstop |= START_AI_INT;
> devpriv->ai_inttrig_start = cmd->start_arg;
> s->async->inttrig = pci9118_ai_inttrig;
> }
> #if 0
> if (cmd->stop_src == TRIG_INT) {
> devpriv->ai_neverending = 1;
> devpriv->ai12_startstop |= STOP_AI_INT;
> }
> #endif
> if (cmd->stop_src == TRIG_NONE)
> devpriv->ai_neverending = 1;
> if (cmd->stop_src == TRIG_COUNT) {
> devpriv->ai_scans = cmd->stop_arg;
> devpriv->ai_neverending = 0;
> } else {
> devpriv->ai_scans = 0;
> }
>
> // use sample&hold signal?
> if (cmd->convert_src == TRIG_NOW) {
> devpriv->usessh = 1;
> } // yes
> else {
> devpriv->usessh = 0;
> } // no
>
> DPRINTK("1 neverending=%d scans=%u usessh=%d ai_startstop=0x%2x\n",
> devpriv->ai_neverending, devpriv->ai_scans, devpriv->usessh,
> devpriv->ai12_startstop);
>
> // use additional sample at end of every scan to satisty DMA 32 bit transfer?
> devpriv->ai_add_front = 0;
> devpriv->ai_add_back = 0;
> devpriv->useeoshandle = 0;
> if (devpriv->master) {
> devpriv->usedma = 1;
> if ((cmd->flags & TRIG_WAKE_EOS) &&
> (devpriv->ai_n_scanlen == 1)) {
> if (cmd->convert_src == TRIG_NOW) {
> devpriv->ai_add_back = 1;
> }
> if (cmd->convert_src == TRIG_TIMER) {
> devpriv->usedma = 0; // use INT transfer if scanlist have only one channel
> }
> }
> if ((cmd->flags & TRIG_WAKE_EOS) &&
> (devpriv->ai_n_scanlen & 1) &&
> (devpriv->ai_n_scanlen > 1)) {
> if (cmd->scan_begin_src == TRIG_FOLLOW) {
> //vpriv->useeoshandle=1; // change DMA transfer block to fit EOS on every second call
> devpriv->usedma = 0; // XXX maybe can be corrected to use 16 bit DMA
> } else { // well, we must insert one sample to end of EOS to meet 32 bit transfer
> devpriv->ai_add_back = 1;
> }
> }
> } else { // interrupt transfer don't need any correction
> devpriv->usedma = 0;
> }
>
> // we need software S&H signal? It add two samples before every scan as minimum
> if (devpriv->usessh && devpriv->softsshdelay) {
> devpriv->ai_add_front = 2;
> if ((devpriv->usedma == 1) && (devpriv->ai_add_back == 1)) { // move it to front
> devpriv->ai_add_front++;
> devpriv->ai_add_back = 0;
> }
> if (cmd->convert_arg < this_board->ai_ns_min)
> cmd->convert_arg = this_board->ai_ns_min;
> addchans = devpriv->softsshdelay / cmd->convert_arg;
> if (devpriv->softsshdelay % cmd->convert_arg)
> addchans++;
> if (addchans > (devpriv->ai_add_front - 1)) { // uff, still short :-(
> devpriv->ai_add_front = addchans + 1;
> if (devpriv->usedma == 1)
> if ((devpriv->ai_add_front +
> devpriv->ai_n_chan +
> devpriv->ai_add_back) & 1)
> devpriv->ai_add_front++; // round up to 32 bit
> }
> } // well, we now know what must be all added
>
> devpriv->ai_n_realscanlen = // what we must take from card in real to have ai_n_scanlen on output?
> (devpriv->ai_add_front + devpriv->ai_n_chan +
> devpriv->ai_add_back) * (devpriv->ai_n_scanlen /
> devpriv->ai_n_chan);
>
> DPRINTK("2 usedma=%d realscan=%d af=%u n_chan=%d ab=%d n_scanlen=%d\n",
> devpriv->usedma,
> devpriv->ai_n_realscanlen, devpriv->ai_add_front,
> devpriv->ai_n_chan, devpriv->ai_add_back,
> devpriv->ai_n_scanlen);
>
> // check and setup channel list
> if (!check_channel_list(dev, s, devpriv->ai_n_chan,
> devpriv->ai_chanlist, devpriv->ai_add_front,
> devpriv->ai_add_back))
> return -EINVAL;
> if (!setup_channel_list(dev, s, devpriv->ai_n_chan,
> devpriv->ai_chanlist, 0, devpriv->ai_add_front,
> devpriv->ai_add_back, devpriv->usedma,
> devpriv->useeoshandle))
> return -EINVAL;
>
> // compute timers settings
> // simplest way, fr=4Mhz/(tim1*tim2), channel manipulation without timers effect
> if (((cmd->scan_begin_src == TRIG_FOLLOW) || (cmd->scan_begin_src == TRIG_EXT) || (cmd->scan_begin_src == TRIG_INT)) && (cmd->convert_src == TRIG_TIMER)) { // both timer is used for one time
> if (cmd->scan_begin_src == TRIG_EXT) {
> devpriv->ai_do = 4;
> } else {
> devpriv->ai_do = 1;
> }
> pci9118_calc_divisors(devpriv->ai_do, dev, s,
> &cmd->scan_begin_arg, &cmd->convert_arg,
> devpriv->ai_flags, devpriv->ai_n_realscanlen,
> &devpriv->ai_divisor1, &devpriv->ai_divisor2,
> devpriv->usessh, devpriv->ai_add_front);
> devpriv->ai_timer2 = cmd->convert_arg;
> }
>
> if ((cmd->scan_begin_src == TRIG_TIMER) && ((cmd->convert_src == TRIG_TIMER) || (cmd->convert_src == TRIG_NOW))) { // double timed action
> if (!devpriv->usedma) {
> comedi_error(dev,
> "cmd->scan_begin_src=TRIG_TIMER works only with bus mastering!");
> return -EIO;
> }
>
> devpriv->ai_do = 2;
> pci9118_calc_divisors(devpriv->ai_do, dev, s,
> &cmd->scan_begin_arg, &cmd->convert_arg,
> devpriv->ai_flags, devpriv->ai_n_realscanlen,
> &devpriv->ai_divisor1, &devpriv->ai_divisor2,
> devpriv->usessh, devpriv->ai_add_front);
> devpriv->ai_timer1 = cmd->scan_begin_arg;
> devpriv->ai_timer2 = cmd->convert_arg;
> }
>
> if ((cmd->scan_begin_src == TRIG_FOLLOW)
> && (cmd->convert_src == TRIG_EXT)) {
> devpriv->ai_do = 3;
> }
>
> start_pacer(dev, -1, 0, 0); // stop pacer
>
> devpriv->AdControlReg = 0; // bipolar, S.E., use 8254, stop 8354, internal trigger, soft trigger, disable DMA
> outl(devpriv->AdControlReg, dev->iobase + PCI9118_ADCNTRL);
> devpriv->AdFunctionReg = AdFunction_PDTrg | AdFunction_PETrg; // positive triggers, no S&H, no burst, burst stop, no post trigger, no about trigger, trigger stop
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC);
> comedi_udelay(1);
> outl(0, dev->iobase + PCI9118_DELFIFO); // flush FIFO
> inl(dev->iobase + PCI9118_ADSTAT); // flush A/D and INT status register
> inl(dev->iobase + PCI9118_INTSRC);
>
> devpriv->ai_act_scan = 0;
> devpriv->ai_act_dmapos = 0;
> s->async->cur_chan = 0;
> devpriv->ai_buf_ptr = 0;
>
> if (devpriv->usedma) {
> ret = pci9118_ai_docmd_dma(dev, s);
> } else {
> ret = pci9118_ai_docmd_sampl(dev, s);
> }
>
> DPRINTK("adl_pci9118 EDBG: END: pci9118_ai_cmd()\n");
> return ret;
> }
>
> /*
> ==============================================================================
> */
> static int check_channel_list(comedi_device * dev, comedi_subdevice * s,
> int n_chan, unsigned int *chanlist, int frontadd, int backadd)
> {
> unsigned int i, differencial = 0, bipolar = 0;
>
> /* correct channel and range number check itself comedi/range.c */
> if (n_chan < 1) {
> comedi_error(dev, "range/channel list is empty!");
> return 0;
> }
> if ((frontadd + n_chan + backadd) > s->len_chanlist) {
> rt_printk
> ("comedi%d: range/channel list is too long for actual configuration (%d>%d)!",
> dev->minor, n_chan,
> s->len_chanlist - frontadd - backadd);
> return 0;
> }
>
> if (CR_AREF(chanlist[0]) == AREF_DIFF)
> differencial = 1; // all input must be diff
> if (CR_RANGE(chanlist[0]) < PCI9118_BIPOLAR_RANGES)
> bipolar = 1; // all input must be bipolar
> if (n_chan > 1)
> for (i = 1; i < n_chan; i++) { // check S.E/diff
> if ((CR_AREF(chanlist[i]) == AREF_DIFF) !=
> (differencial)) {
> comedi_error(dev,
> "Differencial and single ended inputs cann't be mixtured!");
> return 0;
> }
> if ((CR_RANGE(chanlist[i]) < PCI9118_BIPOLAR_RANGES) !=
> (bipolar)) {
> comedi_error(dev,
> "Bipolar and unipolar ranges cann't be mixtured!");
> return 0;
> }
> if ((!devpriv->usemux) & (differencial) &
> (CR_CHAN(chanlist[i]) >=
> this_board->n_aichand)) {
> comedi_error(dev,
> "If AREF_DIFF is used then is available only first 8 channels!");
> return 0;
> }
> }
>
> return 1;
> }
>
> /*
> ==============================================================================
> */
> static int setup_channel_list(comedi_device * dev, comedi_subdevice * s,
> int n_chan, unsigned int *chanlist, int rot, int frontadd, int backadd,
> int usedma, char useeos)
> {
> unsigned int i, differencial = 0, bipolar = 0;
> unsigned int scanquad, gain, ssh = 0x00;
>
> DPRINTK("adl_pci9118 EDBG: BGN: setup_channel_list(%d,.,%d,.,%d,%d,%d,%d)\n", dev->minor, n_chan, rot, frontadd, backadd, usedma);
>
> if (usedma == 1) {
> rot = 8;
> usedma = 0;
> }
>
> if (CR_AREF(chanlist[0]) == AREF_DIFF)
> differencial = 1; // all input must be diff
> if (CR_RANGE(chanlist[0]) < PCI9118_BIPOLAR_RANGES)
> bipolar = 1; // all input must be bipolar
>
> // All is ok, so we can setup channel/range list
>
> if (!bipolar) {
> devpriv->AdControlReg |= AdControl_UniP; // set unibipolar
> } else {
> devpriv->AdControlReg &= ((~AdControl_UniP) & 0xff); // enable bipolar
> }
>
> if (differencial) {
> devpriv->AdControlReg |= AdControl_Diff; // enable diff inputs
> } else {
> devpriv->AdControlReg &= ((~AdControl_Diff) & 0xff); // set single ended inputs
> }
>
> outl(devpriv->AdControlReg, dev->iobase + PCI9118_ADCNTRL); // setup mode
>
> outl(2, dev->iobase + PCI9118_SCANMOD); // gods know why this sequence!
> outl(0, dev->iobase + PCI9118_SCANMOD);
> outl(1, dev->iobase + PCI9118_SCANMOD);
>
> #ifdef PCI9118_PARANOIDCHECK
> devpriv->chanlistlen = n_chan;
> for (i = 0; i < (PCI9118_CHANLEN + 1); i++)
> devpriv->chanlist[i] = 0x55aa;
> #endif
>
> if (frontadd) { // insert channels for S&H
> ssh = devpriv->softsshsample;
> DPRINTK("FA: %04x: ", ssh);
> for (i = 0; i < frontadd; i++) { // store range list to card
> scanquad = CR_CHAN(chanlist[0]); // get channel number;
> gain = CR_RANGE(chanlist[0]); // get gain number
> scanquad |= ((gain & 0x03) << 8);
> outl(scanquad | ssh, dev->iobase + PCI9118_GAIN);
> DPRINTK("%02x ", scanquad | ssh);
> ssh = devpriv->softsshhold;
> }
> DPRINTK("\n ");
> }
>
> DPRINTK("SL: ", ssh);
> for (i = 0; i < n_chan; i++) { // store range list to card
> scanquad = CR_CHAN(chanlist[i]); // get channel number;
> #ifdef PCI9118_PARANOIDCHECK
> devpriv->chanlist[i ^ usedma] = (scanquad & 0xf) << rot;
> #endif
> gain = CR_RANGE(chanlist[i]); // get gain number
> scanquad |= ((gain & 0x03) << 8);
> outl(scanquad | ssh, dev->iobase + PCI9118_GAIN);
> DPRINTK("%02x ", scanquad | ssh);
> }
> DPRINTK("\n ");
>
> if (backadd) { // insert channels for fit onto 32bit DMA
> DPRINTK("BA: %04x: ", ssh);
> for (i = 0; i < backadd; i++) { // store range list to card
> scanquad = CR_CHAN(chanlist[0]); // get channel number;
> gain = CR_RANGE(chanlist[0]); // get gain number
> scanquad |= ((gain & 0x03) << 8);
> outl(scanquad | ssh, dev->iobase + PCI9118_GAIN);
> DPRINTK("%02x ", scanquad | ssh);
> }
> DPRINTK("\n ");
> }
> #ifdef PCI9118_PARANOIDCHECK
> devpriv->chanlist[n_chan ^ usedma] = devpriv->chanlist[0 ^ usedma]; // for 32bit oerations
> if (useeos) {
> for (i = 1; i < n_chan; i++) { // store range list to card
> devpriv->chanlist[(n_chan + i) ^ usedma] =
> (CR_CHAN(chanlist[i]) & 0xf) << rot;
> }
> devpriv->chanlist[(2 * n_chan) ^ usedma] = devpriv->chanlist[0 ^ usedma]; // for 32bit oerations
> useeos = 2;
> } else {
> useeos = 1;
> }
> #ifdef PCI9118_EXTDEBUG
> DPRINTK("CHL: ");
> for (i = 0; i <= (useeos * n_chan); i++) {
> DPRINTK("%04x ", devpriv->chanlist[i]);
> }
> DPRINTK("\n ");
> #endif
> #endif
> outl(0, dev->iobase + PCI9118_SCANMOD); // close scan queue
> // comedi_udelay(100); // important delay, or first sample will be cripled
>
> DPRINTK("adl_pci9118 EDBG: END: setup_channel_list()\n");
> return 1; // we can serve this with scan logic
> }
>
> /*
> ==============================================================================
> calculate 8254 divisors if they are used for dual timing
> */
> static void pci9118_calc_divisors(char mode, comedi_device * dev,
> comedi_subdevice * s, unsigned int *tim1, unsigned int *tim2,
> unsigned int flags, int chans, unsigned int *div1, unsigned int *div2,
> char usessh, unsigned int chnsshfront)
> {
> DPRINTK("adl_pci9118 EDBG: BGN: pci9118_calc_divisors(%d,%d,.,%u,%u,%u,%d,.,.,,%u,%u)\n", mode, dev->minor, *tim1, *tim2, flags, chans, usessh, chnsshfront);
> switch (mode) {
> case 1:
> case 4:
> if (*tim2 < this_board->ai_ns_min)
> *tim2 = this_board->ai_ns_min;
> i8253_cascade_ns_to_timer(devpriv->i8254_osc_base, div1, div2,
> tim2, flags & TRIG_ROUND_NEAREST);
> DPRINTK("OSC base=%u div1=%u div2=%u timer1=%u\n",
> devpriv->i8254_osc_base, *div1, *div2, *tim1);
> break;
> case 2:
> if (*tim2 < this_board->ai_ns_min)
> *tim2 = this_board->ai_ns_min;
> DPRINTK("1 div1=%u div2=%u timer1=%u timer2=%u\n", *div1, *div2,
> *tim1, *tim2);
> *div1 = *tim2 / devpriv->i8254_osc_base; // convert timer (burst)
> DPRINTK("2 div1=%u div2=%u timer1=%u timer2=%u\n", *div1, *div2,
> *tim1, *tim2);
> if (*div1 < this_board->ai_pacer_min)
> *div1 = this_board->ai_pacer_min;
> DPRINTK("3 div1=%u div2=%u timer1=%u timer2=%u\n", *div1, *div2,
> *tim1, *tim2);
> *div2 = *tim1 / devpriv->i8254_osc_base; // scan timer
> DPRINTK("4 div1=%u div2=%u timer1=%u timer2=%u\n", *div1, *div2,
> *tim1, *tim2);
> *div2 = *div2 / *div1; // major timer is c1*c2
> DPRINTK("5 div1=%u div2=%u timer1=%u timer2=%u\n", *div1, *div2,
> *tim1, *tim2);
> if (*div2 < chans)
> *div2 = chans;
> DPRINTK("6 div1=%u div2=%u timer1=%u timer2=%u\n", *div1, *div2,
> *tim1, *tim2);
>
> *tim2 = *div1 * devpriv->i8254_osc_base; // real convert timer
>
> if (usessh & (chnsshfront == 0)) // use BSSH signal
> if (*div2 < (chans + 2))
> *div2 = chans + 2;
>
> DPRINTK("7 div1=%u div2=%u timer1=%u timer2=%u\n", *div1, *div2,
> *tim1, *tim2);
> *tim1 = *div1 * *div2 * devpriv->i8254_osc_base;
> DPRINTK("OSC base=%u div1=%u div2=%u timer1=%u timer2=%u\n",
> devpriv->i8254_osc_base, *div1, *div2, *tim1, *tim2);
> break;
> }
> DPRINTK("adl_pci9118 EDBG: END: pci9118_calc_divisors(%u,%u)\n",
> *div1, *div2);
> }
>
> /*
> ==============================================================================
> */
> static void start_pacer(comedi_device * dev, int mode, unsigned int divisor1,
> unsigned int divisor2)
> {
> outl(0x74, dev->iobase + PCI9118_CNTCTRL);
> outl(0xb4, dev->iobase + PCI9118_CNTCTRL);
> // outl(0x30, dev->iobase + PCI9118_CNTCTRL);
> comedi_udelay(1);
>
> if ((mode == 1) || (mode == 2) || (mode == 4)) {
> outl(divisor2 & 0xff, dev->iobase + PCI9118_CNT2);
> outl((divisor2 >> 8) & 0xff, dev->iobase + PCI9118_CNT2);
> outl(divisor1 & 0xff, dev->iobase + PCI9118_CNT1);
> outl((divisor1 >> 8) & 0xff, dev->iobase + PCI9118_CNT1);
> }
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_exttrg_add(comedi_device * dev, unsigned char source)
> {
> if (source > 3)
> return -1; // incorrect source
> devpriv->exttrg_users |= (1 << source);
> devpriv->IntControlReg |= Int_DTrg;
> outl(devpriv->IntControlReg, dev->iobase + PCI9118_INTCTRL);
> outl(inl(devpriv->iobase_a + AMCC_OP_REG_INTCSR) | 0x1f00, devpriv->iobase_a + AMCC_OP_REG_INTCSR); // allow INT in AMCC
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_exttrg_del(comedi_device * dev, unsigned char source)
> {
> if (source > 3)
> return -1; // incorrect source
> devpriv->exttrg_users &= ~(1 << source);
> if (!devpriv->exttrg_users) { // shutdown ext trg intterrupts
> devpriv->IntControlReg &= ~Int_DTrg;
> if (!devpriv->IntControlReg) // all IRQ disabled
> outl(inl(devpriv->iobase_a + AMCC_OP_REG_INTCSR) & (~0x00001f00), devpriv->iobase_a + AMCC_OP_REG_INTCSR); // disable int in AMCC
> outl(devpriv->IntControlReg, dev->iobase + PCI9118_INTCTRL);
> }
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_ai_cancel(comedi_device * dev, comedi_subdevice * s)
> {
> if (devpriv->usedma)
> outl(inl(devpriv->iobase_a + AMCC_OP_REG_MCSR) & (~EN_A2P_TRANSFERS), devpriv->iobase_a + AMCC_OP_REG_MCSR); // stop DMA
> pci9118_exttrg_del(dev, EXTTRG_AI);
> start_pacer(dev, 0, 0, 0); // stop 8254 counters
> devpriv->AdFunctionReg = AdFunction_PDTrg | AdFunction_PETrg;
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC); // positive triggers, no S&H, no burst, burst stop, no post trigger, no about trigger, trigger stop
> devpriv->AdControlReg = 0x00;
> outl(devpriv->AdControlReg, dev->iobase + PCI9118_ADCNTRL); // bipolar, S.E., use 8254, stop 8354, internal trigger, soft trigger, disable INT and DMA
> outl(0, dev->iobase + PCI9118_BURST);
> outl(1, dev->iobase + PCI9118_SCANMOD);
> outl(2, dev->iobase + PCI9118_SCANMOD); // reset scan queue
> outl(0, dev->iobase + PCI9118_DELFIFO); // flush FIFO
>
> devpriv->ai_do = 0;
> devpriv->usedma = 0;
>
> devpriv->ai_act_scan = 0;
> devpriv->ai_act_dmapos = 0;
> s->async->cur_chan = 0;
> s->async->inttrig = NULL;
> devpriv->ai_buf_ptr = 0;
> devpriv->ai_neverending = 0;
> devpriv->dma_actbuf = 0;
>
> if (!devpriv->IntControlReg)
> outl(inl(devpriv->iobase_a + AMCC_OP_REG_INTCSR) | 0x1f00, devpriv->iobase_a + AMCC_OP_REG_INTCSR); // allow INT in AMCC
>
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_reset(comedi_device * dev)
> {
> devpriv->IntControlReg = 0;
> devpriv->exttrg_users = 0;
> inl(dev->iobase + PCI9118_INTCTRL);
> outl(devpriv->IntControlReg, dev->iobase + PCI9118_INTCTRL); // disable interrupts source
> outl(0x30, dev->iobase + PCI9118_CNTCTRL);
> // outl(0xb4, dev->iobase + PCI9118_CNTCTRL);
> start_pacer(dev, 0, 0, 0); // stop 8254 counters
> devpriv->AdControlReg = 0;
> outl(devpriv->AdControlReg, dev->iobase + PCI9118_ADCNTRL); // bipolar, S.E., use 8254, stop 8354, internal trigger, soft trigger, disable INT and DMA
> outl(0, dev->iobase + PCI9118_BURST);
> outl(1, dev->iobase + PCI9118_SCANMOD);
> outl(2, dev->iobase + PCI9118_SCANMOD); // reset scan queue
> devpriv->AdFunctionReg = AdFunction_PDTrg | AdFunction_PETrg;
> outl(devpriv->AdFunctionReg, dev->iobase + PCI9118_ADFUNC); // positive triggers, no S&H, no burst, burst stop, no post trigger, no about trigger, trigger stop
>
> devpriv->ao_data[0] = 2047;
> devpriv->ao_data[1] = 2047;
> outl(devpriv->ao_data[0], dev->iobase + PCI9118_DA1); // reset A/D outs to 0V
> outl(devpriv->ao_data[1], dev->iobase + PCI9118_DA2);
> outl(0, dev->iobase + PCI9118_DO); // reset digi outs to L
> comedi_udelay(10);
> inl(dev->iobase + PCI9118_AD_DATA);
> outl(0, dev->iobase + PCI9118_DELFIFO); // flush FIFO
> outl(0, dev->iobase + PCI9118_INTSRC); // remove INT requests
> inl(dev->iobase + PCI9118_ADSTAT); // flush A/D status register
> inl(dev->iobase + PCI9118_INTSRC); // flush INT requests
> devpriv->AdControlReg = 0;
> outl(devpriv->AdControlReg, dev->iobase + PCI9118_ADCNTRL); // bipolar, S.E., use 8254, stop 8354, internal trigger, soft trigger, disable INT and DMA
>
> devpriv->cnt0_users = 0;
> devpriv->exttrg_users = 0;
>
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_attach(comedi_device * dev, comedi_devconfig * it)
> {
> comedi_subdevice *s;
> int ret, pages, i;
> unsigned short master;
> unsigned int irq;
> unsigned long iobase_a, iobase_9;
> struct pci_dev *pcidev;
> int opt_bus, opt_slot;
> const char *errstr;
> unsigned char pci_bus, pci_slot, pci_func;
> u16 u16w;
>
> rt_printk("comedi%d: adl_pci9118: board=%s", dev->minor,
> this_board->name);
>
> opt_bus = it->options[0];
> opt_slot = it->options[1];
> if (it->options[3] & 1) {
> master = 0; // user don't want use bus master
> } else {
> master = 1;
> }
>
> if ((ret = alloc_private(dev, sizeof(pci9118_private))) < 0) {
> rt_printk(" - Allocation failed!\n");
> return -ENOMEM;
> }
>
> /* Look for matching PCI device */
> errstr = "not found!";
> pcidev = NULL;
> while (NULL != (pcidev = pci_get_device(PCI_VENDOR_ID_AMCC,
> this_board->device_id, pcidev))) {
> /* Found matching vendor/device. */
> if (opt_bus || opt_slot) {
> /* Check bus/slot. */
> if (opt_bus != pcidev->bus->number
> || opt_slot != PCI_SLOT(pcidev->devfn))
> continue; /* no match */
> }
> /*
> * Look for device that isn't in use.
> * Enable PCI device and request regions.
> */
> if (comedi_pci_enable(pcidev, "adl_pci9118")) {
> errstr = "failed to enable PCI device and request regions!";
> continue;
> }
> break;
> }
>
> if (!pcidev) {
> if (opt_bus || opt_slot) {
> rt_printk(" - Card at b:s %d:%d %s\n",
> opt_bus, opt_slot, errstr);
> } else {
> rt_printk(" - Card %s\n", errstr);
> }
> return -EIO;
> }
>
> if (master) {
> pci_set_master(pcidev);
> }
>
> pci_bus = pcidev->bus->number;
> pci_slot = PCI_SLOT(pcidev->devfn);
> pci_func = PCI_FUNC(pcidev->devfn);
> irq = pcidev->irq;
> iobase_a = pci_resource_start(pcidev, 0);
> iobase_9 = pci_resource_start(pcidev, 2);
>
> rt_printk(", b:s:f=%d:%d:%d, io=0x%4lx, 0x%4lx", pci_bus, pci_slot,
> pci_func, iobase_9, iobase_a);
>
> dev->iobase = iobase_9;
> dev->board_name = this_board->name;
>
> devpriv->pcidev = pcidev;
> devpriv->iobase_a = iobase_a;
>
> pci9118_reset(dev);
>
> if (it->options[3] & 2)
> irq = 0; // user don't want use IRQ
> if (irq > 0) {
> if (comedi_request_irq(irq, interrupt_pci9118, IRQF_SHARED,
> "ADLink PCI-9118", dev)) {
> rt_printk(", unable to allocate IRQ %d, DISABLING IT",
> irq);
> irq = 0; /* Can't use IRQ */
> } else {
> rt_printk(", irq=%u", irq);
> }
> } else {
> rt_printk(", IRQ disabled");
> }
>
> dev->irq = irq;
>
> if (master) { // alloc DMA buffers
> devpriv->dma_doublebuf = 0;
> for (i = 0; i < 2; i++) {
> for (pages = 4; pages >= 0; pages--)
> if ((devpriv->dmabuf_virt[i] = (sampl_t *)
> __get_free_pages(GFP_KERNEL,
> pages)))
> break;
> if (devpriv->dmabuf_virt[i]) {
> devpriv->dmabuf_pages[i] = pages;
> devpriv->dmabuf_size[i] = PAGE_SIZE * pages;
> devpriv->dmabuf_samples[i] =
> devpriv->dmabuf_size[i] >> 1;
> devpriv->dmabuf_hw[i] =
> virt_to_bus((void *)devpriv->
> dmabuf_virt[i]);
> }
> }
> if (!devpriv->dmabuf_virt[0]) {
> rt_printk(", Can't allocate DMA buffer, DMA disabled!");
> master = 0;
> }
>
> if (devpriv->dmabuf_virt[1])
> devpriv->dma_doublebuf = 1;
>
> }
>
> if ((devpriv->master = master)) {
> rt_printk(", bus master");
> } else {
> rt_printk(", no bus master");
> }
>
> devpriv->usemux = 0;
> if (it->options[2] > 0) {
> devpriv->usemux = it->options[2];
> if (devpriv->usemux > 256)
> devpriv->usemux = 256; // max 256 channels!
> if (it->options[4] > 0)
> if (devpriv->usemux > 128) {
> devpriv->usemux = 128; // max 128 channels with softare S&H!
> }
> rt_printk(", ext. mux %d channels", devpriv->usemux);
> }
>
> devpriv->softsshdelay = it->options[4];
> if (devpriv->softsshdelay < 0) { // select sample&hold signal polarity
> devpriv->softsshdelay = -devpriv->softsshdelay;
> devpriv->softsshsample = 0x80;
> devpriv->softsshhold = 0x00;
> } else {
> devpriv->softsshsample = 0x00;
> devpriv->softsshhold = 0x80;
> }
>
> rt_printk(".\n");
>
> pci_read_config_word(devpriv->pcidev, PCI_COMMAND, &u16w);
> pci_write_config_word(devpriv->pcidev, PCI_COMMAND, u16w | 64); // Enable parity check for parity error
>
> if ((ret = alloc_subdevices(dev, 4)) < 0)
> return ret;
>
> s = dev->subdevices + 0;
> dev->read_subdev = s;
> s->type = COMEDI_SUBD_AI;
> s->subdev_flags = SDF_READABLE | SDF_COMMON | SDF_GROUND | SDF_DIFF;
> if (devpriv->usemux) {
> s->n_chan = devpriv->usemux;
> } else {
> s->n_chan = this_board->n_aichan;
> }
> s->maxdata = this_board->ai_maxdata;
> s->len_chanlist = this_board->n_aichanlist;
> s->range_table = this_board->rangelist_ai;
> s->cancel = pci9118_ai_cancel;
> s->insn_read = pci9118_insn_read_ai;
> if (dev->irq) {
> s->subdev_flags |= SDF_CMD_READ;
> s->do_cmdtest = pci9118_ai_cmdtest;
> s->do_cmd = pci9118_ai_cmd;
> s->munge = pci9118_ai_munge;
> }
>
> s = dev->subdevices + 1;
> s->type = COMEDI_SUBD_AO;
> s->subdev_flags = SDF_WRITABLE | SDF_GROUND | SDF_COMMON;
> s->n_chan = this_board->n_aochan;
> s->maxdata = this_board->ao_maxdata;
> s->len_chanlist = this_board->n_aochan;
> s->range_table = this_board->rangelist_ao;
> s->insn_write = pci9118_insn_write_ao;
> s->insn_read = pci9118_insn_read_ao;
>
> s = dev->subdevices + 2;
> s->type = COMEDI_SUBD_DI;
> s->subdev_flags = SDF_READABLE | SDF_GROUND | SDF_COMMON;
> s->n_chan = 4;
> s->maxdata = 1;
> s->len_chanlist = 4;
> s->range_table = &range_digital;
> s->io_bits = 0; /* all bits input */
> s->insn_bits = pci9118_insn_bits_di;
>
> s = dev->subdevices + 3;
> s->type = COMEDI_SUBD_DO;
> s->subdev_flags = SDF_WRITABLE | SDF_GROUND | SDF_COMMON;
> s->n_chan = 4;
> s->maxdata = 1;
> s->len_chanlist = 4;
> s->range_table = &range_digital;
> s->io_bits = 0xf; /* all bits output */
> s->insn_bits = pci9118_insn_bits_do;
>
> devpriv->valid = 1;
> devpriv->i8254_osc_base = 250; // 250ns=4MHz
> devpriv->ai_maskharderr = 0x10a; // default measure crash condition
> if (it->options[5]) // disable some requested
> devpriv->ai_maskharderr &= ~it->options[5];
>
> switch (this_board->ai_maxdata) {
> case 0xffff:
> devpriv->ai16bits = 1;
> break;
> default:
> devpriv->ai16bits = 0;
> break;
> }
> return 0;
> }
>
> /*
> ==============================================================================
> */
> static int pci9118_detach(comedi_device * dev)
> {
> if (dev->private) {
> if (devpriv->valid)
> pci9118_reset(dev);
> if (dev->irq)
> comedi_free_irq(dev->irq, dev);
> if (devpriv->pcidev) {
> if (dev->iobase) {
> comedi_pci_disable(devpriv->pcidev);
> }
> pci_dev_put(devpriv->pcidev);
> }
> if (devpriv->dmabuf_virt[0])
> free_pages((unsigned long)devpriv->dmabuf_virt[0],
> devpriv->dmabuf_pages[0]);
> if (devpriv->dmabuf_virt[1])
> free_pages((unsigned long)devpriv->dmabuf_virt[1],
> devpriv->dmabuf_pages[1]);
> }
>
> return 0;
> }
>
> /*
> ==============================================================================
> */
--
Alexis.
prev parent reply other threads:[~2011-05-16 21:28 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-10-20 21:46 [Xenomai-help] analogy on 9812/9112 daq cards luxInteg
2010-10-21 6:24 ` Alexis Berlemont
2011-05-01 14:46 ` luxInteg
2011-05-16 21:28 ` Alexis Berlemont [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20110516212842.GA2805@domain.hid \
--to=alexis.berlemont@domain.hid \
--cc=lux-integ@domain.hid \
--cc=xenomai@xenomai.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.