From: Jesper Nilsson <jesper.nilsson@axis.com>
To: Paul Bolle <pebolle@tiscali.nl>
Cc: Mikael Starvik <starvik@axis.com>,
linux-cris-kernel <linux-cris-kernel@axis.com>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 21/21] cris: drop unused Kconfig symbols
Date: Fri, 14 Oct 2011 15:33:54 +0200 [thread overview]
Message-ID: <20111014133354.GE9412@axis.com> (raw)
In-Reply-To: <1318595467.6132.80.camel@x61.thuisdomein>
Hmmm... NAK on that. Lots of these configs are actually used, but in drivers
not upstream yet (serial port, ethernet and usb drivers for ARTPEC-3).
However, the following seem to truly be unused:
ETRAX_NANDFLASH_BUSWIDTH
ETRAX_PA_BUTTON_BITMASK
ETRAX_DDR
If you send a modified patch with just those configs I will be happy. :-)
Thanks,
/Jesper
On Fri, Oct 14, 2011 at 02:31:07PM +0200, Paul Bolle wrote:
> Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
> ---
> arch/cris/Kconfig | 49 -----
> arch/cris/arch-v10/drivers/Kconfig | 23 ---
> arch/cris/arch-v32/drivers/Kconfig | 380 ------------------------------------
> arch/cris/arch-v32/mach-a3/Kconfig | 4 -
> 4 files changed, 0 insertions(+), 456 deletions(-)
>
> diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig
> index 17addac..6a0dc11 100644
> --- a/arch/cris/Kconfig
> +++ b/arch/cris/Kconfig
> @@ -98,9 +98,6 @@ config ETRAX_KMALLOCED_MODULES
> help
> Enable module allocation with kmalloc instead of vmalloc.
>
> -config OOM_REBOOT
> - bool "Enable reboot at out of memory"
> -
> source "kernel/Kconfig.preempt"
>
> source mm/Kconfig
> @@ -177,12 +174,6 @@ config ETRAX_FLASH_BUSWIDTH
> help
> Width in bytes of the NOR Flash bus (1, 2 or 4). Is usually 2.
>
> -config ETRAX_NANDFLASH_BUSWIDTH
> - int "Buswidth of NAND flash in bytes"
> - default "1"
> - help
> - Width in bytes of the NAND flash (1 or 2).
> -
> config ETRAX_FLASH1_SIZE
> int "FLASH1 size (dec, in MB. 0 = Unknown)"
> default "0"
> @@ -581,26 +572,6 @@ config ETRAX_SERIAL_PORT3_DMA5_IN
> depends on ETRAX_ARCH_V10
> bool "DMA 5"
>
> -config ETRAX_SERIAL_PORT3_DMA9_IN
> - bool "Ser3 uses DMA9 for input"
> - depends on ETRAXFS
> - help
> - Enables the DMA9 input channel for ser3 (ttyS3).
> - If you do not enable DMA, an interrupt for each character will be
> - used when receiving data.
> - Normally you want to use DMA, unless you use the DMA channel for
> - something else.
> -
> -config ETRAX_SERIAL_PORT3_DMA3_IN
> - bool "Ser3 uses DMA3 for input"
> - depends on CRIS_MACH_ARTPEC3
> - help
> - Enables the DMA3 input channel for ser3 (ttyS3).
> - If you do not enable DMA, an interrupt for each character will be
> - used when receiving data.
> - Normally you want to use DMA, unless you use the DMA channel for
> - something else.
> -
> endchoice
>
> choice
> @@ -618,26 +589,6 @@ config ETRAX_SERIAL_PORT3_DMA4_OUT
> depends on ETRAX_ARCH_V10
> bool "DMA 4"
>
> -config ETRAX_SERIAL_PORT3_DMA8_OUT
> - bool "Ser3 uses DMA8 for output"
> - depends on ETRAXFS
> - help
> - Enables the DMA8 output channel for ser3 (ttyS3).
> - If you do not enable DMA, an interrupt for each character will be
> - used when transmitting data.
> - Normally you want to use DMA, unless you use the DMA channel for
> - something else.
> -
> -config ETRAX_SERIAL_PORT3_DMA2_OUT
> - bool "Ser3 uses DMA2 for output"
> - depends on CRIS_MACH_ARTPEC3
> - help
> - Enables the DMA2 output channel for ser3 (ttyS3).
> - If you do not enable DMA, an interrupt for each character will be
> - used when transmitting data.
> - Normally you want to use DMA, unless you use the DMA channel for
> - something else.
> -
> endchoice
>
> endmenu
> diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
> index 0d72217..12f2f04 100644
> --- a/arch/cris/arch-v10/drivers/Kconfig
> +++ b/arch/cris/arch-v10/drivers/Kconfig
> @@ -418,16 +418,6 @@ config ETRAX_USB_HOST
> for CTRL and BULK traffic only, INTR traffic may work as well
> however (depending on the requirements of timeliness).
>
> -config ETRAX_USB_HOST_PORT1
> - bool "USB port 1 enabled"
> - depends on ETRAX_USB_HOST
> - default n
> -
> -config ETRAX_USB_HOST_PORT2
> - bool "USB port 2 enabled"
> - depends on ETRAX_USB_HOST
> - default n
> -
> config ETRAX_PTABLE_SECTOR
> int "Byte-offset of partition table sector"
> depends on ETRAX_AXISFLASHMAP
> @@ -528,19 +518,6 @@ config ETRAX_GPIO
> Remember that you need to setup the port directions appropriately in
> the General configuration.
>
> -config ETRAX_PA_BUTTON_BITMASK
> - hex "PA-buttons bitmask"
> - depends on ETRAX_GPIO
> - default "02"
> - help
> - This is a bitmask with information about what bits on PA that
> - are used for buttons.
> - Most products has a so called TEST button on PA1, if that's true
> - use 02 here.
> - Use 00 if there are no buttons on PA.
> - If the bitmask is <> 00 a button driver will be included in the gpio
> - driver. ETRAX general I/O support must be enabled.
> -
> config ETRAX_PA_CHANGEABLE_DIR
> hex "PA user changeable dir mask"
> depends on ETRAX_GPIO
> diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig
> index 41a2732..3488a79 100644
> --- a/arch/cris/arch-v32/drivers/Kconfig
> +++ b/arch/cris/arch-v32/drivers/Kconfig
> @@ -28,56 +28,6 @@ config ETRAX_ETHERNET_IFACE1
> depends on (ETRAX_ETHERNET && ETRAXFS)
> bool "Enable network interface 1 (uses DMA6 and DMA7)"
>
> -config ETRAX_ETHERNET_GBIT
> - depends on (ETRAX_ETHERNET && CRIS_MACH_ARTPEC3)
> - bool "Enable gigabit Ethernet support"
> -
> -choice
> - prompt "Eth0 led group"
> - depends on ETRAX_ETHERNET_IFACE0
> - default ETRAX_ETH0_USE_LEDGRP0
> -
> -config ETRAX_ETH0_USE_LEDGRP0
> - bool "Use LED grp 0"
> - depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
> - help
> - Use LED grp 0 for eth0
> -
> -config ETRAX_ETH0_USE_LEDGRP1
> - bool "Use LED grp 1"
> - depends on ETRAX_NBR_LED_GRP_TWO
> - help
> - Use LED grp 1 for eth0
> -
> -config ETRAX_ETH0_USE_LEDGRPNULL
> - bool "Use no LEDs for eth0"
> - help
> - Use no LEDs for eth0
> -endchoice
> -
> -choice
> - prompt "Eth1 led group"
> - depends on ETRAX_ETHERNET_IFACE1
> - default ETRAX_ETH1_USE_LEDGRP1
> -
> -config ETRAX_ETH1_USE_LEDGRP0
> - bool "Use LED grp 0"
> - depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
> - help
> - Use LED grp 0 for eth1
> -
> -config ETRAX_ETH1_USE_LEDGRP1
> - bool "Use LED grp 1"
> - depends on ETRAX_NBR_LED_GRP_TWO
> - help
> - Use LED grp 1 for eth1
> -
> -config ETRAX_ETH1_USE_LEDGRPNULL
> - bool "Use no LEDs for eth1"
> - help
> - Use no LEDs for eth1
> -endchoice
> -
> config ETRAXFS_SERIAL
> bool "Serial-port support"
> depends on ETRAX_ARCH_V32
> @@ -109,261 +59,30 @@ config ETRAX_SERIAL_PORT0
> if you do not need DMA to something else.
> ser0 can use dma4 or dma6 for output and dma5 or dma7 for input.
>
> -choice
> - prompt "Ser0 default port type "
> - depends on ETRAX_SERIAL_PORT0
> - default ETRAX_SERIAL_PORT0_TYPE_232
> - help
> - Type of serial port.
> -
> -config ETRAX_SERIAL_PORT0_TYPE_232
> - bool "Ser0 is a RS-232 port"
> - help
> - Configure serial port 0 to be a RS-232 port.
> -
> -config ETRAX_SERIAL_PORT0_TYPE_485HD
> - bool "Ser0 is a half duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 0 to be a half duplex (two wires) RS-485 port.
> -
> -config ETRAX_SERIAL_PORT0_TYPE_485FD
> - bool "Ser0 is a full duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 0 to be a full duplex (four wires) RS-485 port.
> -endchoice
> -
> -config ETRAX_SER0_DTR_BIT
> - string "Ser 0 DTR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT0
> -
> -config ETRAX_SER0_RI_BIT
> - string "Ser 0 RI bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT0
> -
> -config ETRAX_SER0_DSR_BIT
> - string "Ser 0 DSR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT0
> -
> -config ETRAX_SER0_CD_BIT
> - string "Ser 0 CD bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT0
> -
> config ETRAX_SERIAL_PORT1
> bool "Serial port 1 enabled"
> depends on ETRAXFS_SERIAL
> help
> Enables the ETRAX FS serial driver for ser1 (ttyS1).
>
> -choice
> - prompt "Ser1 default port type"
> - depends on ETRAX_SERIAL_PORT1
> - default ETRAX_SERIAL_PORT1_TYPE_232
> - help
> - Type of serial port.
> -
> -config ETRAX_SERIAL_PORT1_TYPE_232
> - bool "Ser1 is a RS-232 port"
> - help
> - Configure serial port 1 to be a RS-232 port.
> -
> -config ETRAX_SERIAL_PORT1_TYPE_485HD
> - bool "Ser1 is a half duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 1 to be a half duplex (two wires) RS-485 port.
> -
> -config ETRAX_SERIAL_PORT1_TYPE_485FD
> - bool "Ser1 is a full duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 1 to be a full duplex (four wires) RS-485 port.
> -endchoice
> -
> -config ETRAX_SER1_DTR_BIT
> - string "Ser 1 DTR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT1
> -
> -config ETRAX_SER1_RI_BIT
> - string "Ser 1 RI bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT1
> -
> -config ETRAX_SER1_DSR_BIT
> - string "Ser 1 DSR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT1
> -
> -config ETRAX_SER1_CD_BIT
> - string "Ser 1 CD bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT1
> -
> config ETRAX_SERIAL_PORT2
> bool "Serial port 2 enabled"
> depends on ETRAXFS_SERIAL
> help
> Enables the ETRAX FS serial driver for ser2 (ttyS2).
>
> -choice
> - prompt "Ser2 default port type"
> - depends on ETRAX_SERIAL_PORT2
> - default ETRAX_SERIAL_PORT2_TYPE_232
> - help
> - What DMA channel to use for ser2
> -
> -config ETRAX_SERIAL_PORT2_TYPE_232
> - bool "Ser2 is a RS-232 port"
> - help
> - Configure serial port 2 to be a RS-232 port.
> -
> -config ETRAX_SERIAL_PORT2_TYPE_485HD
> - bool "Ser2 is a half duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 2 to be a half duplex (two wires) RS-485 port.
> -
> -config ETRAX_SERIAL_PORT2_TYPE_485FD
> - bool "Ser2 is a full duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 2 to be a full duplex (four wires) RS-485 port.
> -endchoice
> -
> -
> -config ETRAX_SER2_DTR_BIT
> - string "Ser 2 DTR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT2
> -
> -config ETRAX_SER2_RI_BIT
> - string "Ser 2 RI bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT2
> -
> -config ETRAX_SER2_DSR_BIT
> - string "Ser 2 DSR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT2
> -
> -config ETRAX_SER2_CD_BIT
> - string "Ser 2 CD bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT2
> -
> config ETRAX_SERIAL_PORT3
> bool "Serial port 3 enabled"
> depends on ETRAXFS_SERIAL
> help
> Enables the ETRAX FS serial driver for ser3 (ttyS3).
>
> -choice
> - prompt "Ser3 default port type"
> - depends on ETRAX_SERIAL_PORT3
> - default ETRAX_SERIAL_PORT3_TYPE_232
> - help
> - What DMA channel to use for ser3.
> -
> -config ETRAX_SERIAL_PORT3_TYPE_232
> - bool "Ser3 is a RS-232 port"
> - help
> - Configure serial port 3 to be a RS-232 port.
> -
> -config ETRAX_SERIAL_PORT3_TYPE_485HD
> - bool "Ser3 is a half duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 3 to be a half duplex (two wires) RS-485 port.
> -
> -config ETRAX_SERIAL_PORT3_TYPE_485FD
> - bool "Ser3 is a full duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 3 to be a full duplex (four wires) RS-485 port.
> -endchoice
> -
> -config ETRAX_SER3_DTR_BIT
> - string "Ser 3 DTR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT3
> -
> -config ETRAX_SER3_RI_BIT
> - string "Ser 3 RI bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT3
> -
> -config ETRAX_SER3_DSR_BIT
> - string "Ser 3 DSR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT3
> -
> -config ETRAX_SER3_CD_BIT
> - string "Ser 3 CD bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT3
> -
> config ETRAX_SERIAL_PORT4
> bool "Serial port 4 enabled"
> depends on ETRAXFS_SERIAL && CRIS_MACH_ARTPEC3
> help
> Enables the ETRAX FS serial driver for ser4 (ttyS4).
>
> -choice
> - prompt "Ser4 default port type"
> - depends on ETRAX_SERIAL_PORT4
> - default ETRAX_SERIAL_PORT4_TYPE_232
> - help
> - What DMA channel to use for ser4.
> -
> -config ETRAX_SERIAL_PORT4_TYPE_232
> - bool "Ser4 is a RS-232 port"
> - help
> - Configure serial port 4 to be a RS-232 port.
> -
> -config ETRAX_SERIAL_PORT4_TYPE_485HD
> - bool "Ser4 is a half duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 4 to be a half duplex (two wires) RS-485 port.
> -
> -config ETRAX_SERIAL_PORT4_TYPE_485FD
> - bool "Ser4 is a full duplex RS-485 port"
> - depends on ETRAX_RS485
> - help
> - Configure serial port 4 to be a full duplex (four wires) RS-485 port.
> -endchoice
> -
> -choice
> - prompt "Ser4 DMA in channel "
> - depends on ETRAX_SERIAL_PORT4
> - default ETRAX_SERIAL_PORT4_NO_DMA_IN
> - help
> - What DMA channel to use for ser4.
> -
> -
> -config ETRAX_SERIAL_PORT4_NO_DMA_IN
> - bool "Ser4 uses no DMA for input"
> - help
> - Do not use DMA for ser4 input.
> -
> -config ETRAX_SERIAL_PORT4_DMA9_IN
> - bool "Ser4 uses DMA9 for input"
> - depends on ETRAX_SERIAL_PORT4
> - help
> - Enables the DMA9 input channel for ser4 (ttyS4).
> - If you do not enable DMA, an interrupt for each character will be
> - used when receiving data.
> - Normally you want to use DMA, unless you use the DMA channel for
> - something else.
> -
> -endchoice
> -
> -config ETRAX_SER4_DTR_BIT
> - string "Ser 4 DTR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT4
> -
> -config ETRAX_SER4_RI_BIT
> - string "Ser 4 RI bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT4
> -
> -config ETRAX_SER4_DSR_BIT
> - string "Ser 4 DSR bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT4
> -
> -config ETRAX_SER4_CD_BIT
> - string "Ser 4 CD bit (empty = not used)"
> - depends on ETRAX_SERIAL_PORT4
> -
> config ETRAX_SYNCHRONOUS_SERIAL
> bool "Synchronous serial-port support"
> depends on ETRAX_ARCH_V32
> @@ -708,32 +427,6 @@ config ETRAX_SPI_SSER0
> want to build it as a module, which will be named spi_crisv32_sser.
> (You need to select MMC separately.)
>
> -config ETRAX_SPI_SSER0_DMA
> - bool "DMA for SPI on sser0 enabled"
> - depends on ETRAX_SPI_SSER0
> - depends on !ETRAX_SERIAL_PORT1_DMA4_OUT && !ETRAX_SERIAL_PORT1_DMA5_IN
> - default y
> - help
> - Say Y if using DMA (dma4/dma5) for SPI on synchronous serial port 0.
> -
> -config ETRAX_SPI_MMC_CD_SSER0_PIN
> - string "MMC/SD card detect pin for SPI on sser0"
> - depends on ETRAX_SPI_SSER0 && MMC_SPI
> - default "pd11"
> - help
> - The pin to use for SD/MMC card detect. This pin should be pulled up
> - and grounded when a card is present. If defined as " " (space), no
> - pin is selected. A card must then always be inserted for proper
> - action.
> -
> -config ETRAX_SPI_MMC_WP_SSER0_PIN
> - string "MMC/SD card write-protect pin for SPI on sser0"
> - depends on ETRAX_SPI_SSER0 && MMC_SPI
> - default "pd10"
> - help
> - The pin to use for the SD/MMC write-protect signal for a memory
> - card. If defined as " " (space), the card is considered writable.
> -
> config ETRAX_SPI_SSER1
> tristate "SPI using synchronous serial port 1 (sser1)"
> depends on ETRAX_SPI_MMC
> @@ -747,32 +440,6 @@ config ETRAX_SPI_SSER1
> want to build it as a module, which will be named spi_crisv32_sser.
> (You need to select MMC separately.)
>
> -config ETRAX_SPI_SSER1_DMA
> - bool "DMA for SPI on sser1 enabled"
> - depends on ETRAX_SPI_SSER1 && !ETRAX_ETHERNET_IFACE1
> - depends on !ETRAX_SERIAL_PORT0_DMA6_OUT && !ETRAX_SERIAL_PORT0_DMA7_IN
> - default y
> - help
> - Say Y if using DMA (dma6/dma7) for SPI on synchronous serial port 1.
> -
> -config ETRAX_SPI_MMC_CD_SSER1_PIN
> - string "MMC/SD card detect pin for SPI on sser1"
> - depends on ETRAX_SPI_SSER1 && MMC_SPI
> - default "pd12"
> - help
> - The pin to use for SD/MMC card detect. This pin should be pulled up
> - and grounded when a card is present. If defined as " " (space), no
> - pin is selected. A card must then always be inserted for proper
> - action.
> -
> -config ETRAX_SPI_MMC_WP_SSER1_PIN
> - string "MMC/SD card write-protect pin for SPI on sser1"
> - depends on ETRAX_SPI_SSER1 && MMC_SPI
> - default "pd9"
> - help
> - The pin to use for the SD/MMC write-protect signal for a memory
> - card. If defined as " " (space), the card is considered writable.
> -
> config ETRAX_SPI_GPIO
> tristate "Bitbanged SPI using gpio pins"
> depends on ETRAX_SPI_MMC
> @@ -787,53 +454,6 @@ config ETRAX_SPI_GPIO
> Say m to build it as a module, which will be called spi_crisv32_gpio.
> (You need to select MMC separately.)
>
> -# The default match that of sser0, only because that's how it was tested.
> -config ETRAX_SPI_CS_PIN
> - string "SPI chip select pin"
> - depends on ETRAX_SPI_GPIO
> - default "pc3"
> - help
> - The pin to use for SPI chip select.
> -
> -config ETRAX_SPI_CLK_PIN
> - string "SPI clock pin"
> - depends on ETRAX_SPI_GPIO
> - default "pc1"
> - help
> - The pin to use for the SPI clock.
> -
> -config ETRAX_SPI_DATAIN_PIN
> - string "SPI MISO (data in) pin"
> - depends on ETRAX_SPI_GPIO
> - default "pc16"
> - help
> - The pin to use for SPI data in from the device.
> -
> -config ETRAX_SPI_DATAOUT_PIN
> - string "SPI MOSI (data out) pin"
> - depends on ETRAX_SPI_GPIO
> - default "pc0"
> - help
> - The pin to use for SPI data out to the device.
> -
> -config ETRAX_SPI_MMC_CD_GPIO_PIN
> - string "MMC/SD card detect pin for SPI using gpio (space for none)"
> - depends on ETRAX_SPI_GPIO && MMC_SPI
> - default "pd11"
> - help
> - The pin to use for SD/MMC card detect. This pin should be pulled up
> - and grounded when a card is present. If defined as " " (space), no
> - pin is selected. A card must then always be inserted for proper
> - action.
> -
> -config ETRAX_SPI_MMC_WP_GPIO_PIN
> - string "MMC/SD card write-protect pin for SPI using gpio (space for none)"
> - depends on ETRAX_SPI_GPIO && MMC_SPI
> - default "pd10"
> - help
> - The pin to use for the SD/MMC write-protect signal for a memory
> - card. If defined as " " (space), the card is considered writable.
> -
> # Avoid choices causing non-working configs by conditionalizing the inclusion.
> if ETRAX_SPI_MMC
> source drivers/spi/Kconfig
> diff --git a/arch/cris/arch-v32/mach-a3/Kconfig b/arch/cris/arch-v32/mach-a3/Kconfig
> index 7796aaf..8754727 100644
> --- a/arch/cris/arch-v32/mach-a3/Kconfig
> +++ b/arch/cris/arch-v32/mach-a3/Kconfig
> @@ -15,10 +15,6 @@ config ETRAX_SERIAL_PORTS
> int
> default 5
>
> -config ETRAX_DDR
> - bool
> - default y
> -
> config ETRAX_DDR2_MRS
> hex "DDR2 MRS"
> default "0"
> --
> 1.7.4.4
>
>
>
/^JN - Jesper Nilsson
--
Jesper Nilsson -- jesper.nilsson@axis.com
next prev parent reply other threads:[~2011-10-14 13:33 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-10-14 12:31 [PATCH 21/21] cris: drop unused Kconfig symbols Paul Bolle
2011-10-14 13:33 ` Jesper Nilsson [this message]
2011-10-14 14:05 ` Paul Bolle
2011-10-14 19:11 ` Valdis.Kletnieks
2011-10-31 10:59 ` Jesper Nilsson
2013-03-23 13:14 ` Paul Bolle
2013-04-15 15:11 ` Jesper Nilsson
2013-04-16 8:34 ` [PATCH v2] " Paul Bolle
2013-04-16 13:46 ` Jesper Nilsson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20111014133354.GE9412@axis.com \
--to=jesper.nilsson@axis.com \
--cc=linux-cris-kernel@axis.com \
--cc=linux-kernel@vger.kernel.org \
--cc=pebolle@tiscali.nl \
--cc=starvik@axis.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.