From: NeilBrown <neilb@suse.de>
To: linux-raid@vger.kernel.org
Subject: [md PATCH 08/16] md/raid5: remove redundant bio initialisations.
Date: Wed, 26 Oct 2011 12:43:01 +1100 [thread overview]
Message-ID: <20111026014301.21110.69146.stgit@notabene.brown> (raw)
In-Reply-To: <20111026014240.21110.28487.stgit@notabene.brown>
We current initialise some fields of a bio when preparing a
stripe_head, and again just before submitting the request.
Remove the duplication by only setting the fields that lower level
devices don't touch in raid5_build_block, and only set the changeable
fields in ops_run_io.
Signed-off-by: NeilBrown <neilb@suse.de>
---
drivers/md/raid5.c | 9 +--------
1 files changed, 1 insertions(+), 8 deletions(-)
diff --git a/drivers/md/raid5.c b/drivers/md/raid5.c
index e6d10df..12e54c0 100644
--- a/drivers/md/raid5.c
+++ b/drivers/md/raid5.c
@@ -562,10 +562,7 @@ static void ops_run_io(struct stripe_head *sh, struct stripe_head_state *s)
atomic_inc(&sh->count);
bi->bi_sector = sh->sector + rdev->data_offset;
bi->bi_flags = 1 << BIO_UPTODATE;
- bi->bi_vcnt = 1;
- bi->bi_max_vecs = 1;
bi->bi_idx = 0;
- bi->bi_io_vec = &sh->dev[i].vec;
bi->bi_io_vec[0].bv_len = STRIPE_SIZE;
bi->bi_io_vec[0].bv_offset = 0;
bi->bi_size = STRIPE_SIZE;
@@ -1708,12 +1705,8 @@ static void raid5_build_block(struct stripe_head *sh, int i, int previous)
dev->req.bi_io_vec = &dev->vec;
dev->req.bi_vcnt++;
dev->req.bi_max_vecs++;
- dev->vec.bv_page = dev->page;
- dev->vec.bv_len = STRIPE_SIZE;
- dev->vec.bv_offset = 0;
-
- dev->req.bi_sector = sh->sector;
dev->req.bi_private = sh;
+ dev->vec.bv_page = dev->page;
dev->flags = 0;
dev->sector = compute_blocknr(sh, i, previous);
next prev parent reply other threads:[~2011-10-26 1:43 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-10-26 1:43 [md PATCH 00/16] hot-replace support for RAID4/5/6 NeilBrown
2011-10-26 1:43 ` [md PATCH 03/16] md: remove test for duplicate device when setting slot number NeilBrown
2011-10-26 1:43 ` [md PATCH 01/16] md: refine interpretation of "hold_active == UNTIL_IOCTL" NeilBrown
2011-10-26 1:43 ` [md PATCH 02/16] md: take after reference to mddev during sysfs access NeilBrown
2011-10-26 1:43 ` [md PATCH 04/16] md: change hot_remove_disk to take an rdev rather than a number NeilBrown
2011-10-26 1:43 ` [md PATCH 10/16] md/raid5: allow removal for failed replacement devices NeilBrown
2011-10-26 1:43 ` [md PATCH 12/16] md/raid5: detect and handle replacements during recovery NeilBrown
2011-10-26 1:43 ` [md PATCH 09/16] md/raid5: preferentially read from replacement device if possible NeilBrown
2011-10-26 1:43 ` [md PATCH 05/16] md: create externally visible flags for supporting hot-replace NeilBrown
2011-10-26 1:43 ` [md PATCH 14/16] md/raid5: recognise replacements when assembling array NeilBrown
2011-10-26 1:43 ` [md PATCH 13/16] md/raid5: handle activation of replacement device when recovery completes NeilBrown
2011-10-26 1:43 ` NeilBrown [this message]
2011-10-26 1:43 ` [md PATCH 06/16] md/raid5: allow each slot to have an extra replacement device NeilBrown
2011-10-26 1:43 ` [md PATCH 11/16] md/raid5: writes should get directed to replacement as well as original NeilBrown
2011-10-26 1:43 ` [md PATCH 07/16] md/raid5: raid5.h cleanup NeilBrown
2011-10-26 1:43 ` [md PATCH 16/16] md/raid5: Mark device replaceable when we see a write error NeilBrown
2011-10-26 1:43 ` [md PATCH 15/16] md/raid5: If there is a spare and a replaceable device, start replacement NeilBrown
2011-10-26 6:38 ` [md PATCH 00/16] hot-replace support for RAID4/5/6 David Brown
2011-10-26 7:42 ` NeilBrown
2011-10-26 9:01 ` John Robinson
2011-10-26 13:57 ` Peter W. Morreale
2011-10-26 17:27 ` Piergiorgio Sartor
2011-10-27 17:10 ` Peter W. Morreale
2011-10-27 20:44 ` NeilBrown
2011-10-27 20:53 ` Peter W. Morreale
2011-12-14 22:18 ` Dan Williams
2011-12-15 6:18 ` NeilBrown
2011-12-15 7:14 ` Williams, Dan J
2011-12-20 5:18 ` NeilBrown
2011-12-22 20:54 ` Alexander Kühn
2011-12-22 21:14 ` NeilBrown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20111026014301.21110.69146.stgit@notabene.brown \
--to=neilb@suse.de \
--cc=linux-raid@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.