* s3c2440 / s3c2416 broken
@ 2011-11-09 22:12 Paul Schilling
2011-11-09 23:30 ` Paul Schilling
0 siblings, 1 reply; 14+ messages in thread
From: Paul Schilling @ 2011-11-09 22:12 UTC (permalink / raw)
To: linux-arm-kernel
Latest kernel 3.2.0-rc1 appears to break the following processors
s3c2440 and s3c2416
both appear to stall when init is executed on NFS. Also I lost HSMMC on
the s3c2416.
Thanks,
Paul
^ permalink raw reply [flat|nested] 14+ messages in thread
* s3c2440 / s3c2416 broken
2011-11-09 22:12 s3c2440 / s3c2416 broken Paul Schilling
@ 2011-11-09 23:30 ` Paul Schilling
2011-11-10 0:14 ` Thomas Abraham
0 siblings, 1 reply; 14+ messages in thread
From: Paul Schilling @ 2011-11-09 23:30 UTC (permalink / raw)
To: linux-arm-kernel
Boot past init slow - stalled when using jffs2 also.
On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
<paul.s.schilling@gmail.com> wrote:
> Latest kernel 3.2.0-rc1 appears to break the following processors
> s3c2440 and s3c2416
>
> both appear to stall when init is executed on NFS. ?Also I ?lost HSMMC on
> the s3c2416.
>
> Thanks,
> Paul
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: s3c2440 / s3c2416 broken
2011-11-09 23:30 ` Paul Schilling
@ 2011-11-10 0:14 ` Thomas Abraham
0 siblings, 0 replies; 14+ messages in thread
From: Thomas Abraham @ 2011-11-10 0:14 UTC (permalink / raw)
To: Paul Schilling
Cc: linux-arm-kernel, Kukjin Kim, Russell King, linux-samsung-soc
On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com> wrote:
> Boot past init slow - stalled when using jffs2 also.
>
> On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
> <paul.s.schilling@gmail.com> wrote:
>> Latest kernel 3.2.0-rc1 appears to break the following processors
>> s3c2440 and s3c2416
>>
>> both appear to stall when init is executed on NFS. Also I lost HSMMC on
>> the s3c2416.
Could you post a boot log of the kernel on the s3c2440 and s3c2416 boards?
Thanks,
Thomas.
>>
>> Thanks,
>> Paul
>>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* s3c2440 / s3c2416 broken
@ 2011-11-10 0:14 ` Thomas Abraham
0 siblings, 0 replies; 14+ messages in thread
From: Thomas Abraham @ 2011-11-10 0:14 UTC (permalink / raw)
To: linux-arm-kernel
On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com> wrote:
> Boot past init slow - stalled when using jffs2 also.
>
> On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
> <paul.s.schilling@gmail.com> wrote:
>> Latest kernel 3.2.0-rc1 appears to break the following processors
>> s3c2440 and s3c2416
>>
>> both appear to stall when init is executed on NFS. ?Also I ?lost HSMMC on
>> the s3c2416.
Could you post a boot log of the kernel on the s3c2440 and s3c2416 boards?
Thanks,
Thomas.
>>
>> Thanks,
>> Paul
>>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: s3c2440 / s3c2416 broken
2011-11-10 0:14 ` Thomas Abraham
@ 2011-11-10 7:59 ` Heiko Stübner
-1 siblings, 0 replies; 14+ messages in thread
From: Heiko Stübner @ 2011-11-10 7:59 UTC (permalink / raw)
To: linux-arm-kernel, Paul Schilling, linux-samsung-soc
Cc: Thomas Abraham, Kukjin Kim, Russell King
Hi Paul,
Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
wrote:
> > Boot past init slow - stalled when using jffs2 also.
> >
> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
> >
> > <paul.s.schilling@gmail.com> wrote:
> >> Latest kernel 3.2.0-rc1 appears to break the following processors
> >> s3c2440 and s3c2416
> >>
> >> both appear to stall when init is executed on NFS. Also I lost HSMMC
> >> on the s3c2416.
>
> Could you post a boot log of the kernel on the s3c2440 and s3c2416 boards?
Also, is your out-of-tree kernel code available somewhere? [1]
As my S3C2416 based platform didn't show any problems and has working hsmmc
with 3.2-rc1 it would be cool to be able to compare both and see if we differ
somehow.
Heiko
[1] Mine's at https://gitorious.org/oyo-hack/kernel/commits/topic/board/sg060
^ permalink raw reply [flat|nested] 14+ messages in thread
* s3c2440 / s3c2416 broken
@ 2011-11-10 7:59 ` Heiko Stübner
0 siblings, 0 replies; 14+ messages in thread
From: Heiko Stübner @ 2011-11-10 7:59 UTC (permalink / raw)
To: linux-arm-kernel
Hi Paul,
Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
wrote:
> > Boot past init slow - stalled when using jffs2 also.
> >
> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
> >
> > <paul.s.schilling@gmail.com> wrote:
> >> Latest kernel 3.2.0-rc1 appears to break the following processors
> >> s3c2440 and s3c2416
> >>
> >> both appear to stall when init is executed on NFS. Also I lost HSMMC
> >> on the s3c2416.
>
> Could you post a boot log of the kernel on the s3c2440 and s3c2416 boards?
Also, is your out-of-tree kernel code available somewhere? [1]
As my S3C2416 based platform didn't show any problems and has working hsmmc
with 3.2-rc1 it would be cool to be able to compare both and see if we differ
somehow.
Heiko
[1] Mine's at https://gitorious.org/oyo-hack/kernel/commits/topic/board/sg060
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: s3c2440 / s3c2416 broken
2011-11-10 7:59 ` Heiko Stübner
@ 2011-11-10 15:57 ` Paul Schilling
-1 siblings, 0 replies; 14+ messages in thread
From: Paul Schilling @ 2011-11-10 15:57 UTC (permalink / raw)
To: Heiko Stübner
Cc: linux-arm-kernel, linux-samsung-soc, Thomas Abraham, Kukjin Kim,
Russell King
Here is my boot log including some u-boot stuff. The trace in my boot
log is concerning a
still broken GPIO bank M access that appears broken.
Thanks,
Paul Schilling
dm9000 i/o: 0x20000300, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 12:23:34:88:99:00
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 10.5.16.68
TFTP from server 10.5.16.63; our IP address is 10.5.16.68
Filename 'schilpa/uImage-dev.bin'.
Load address: 0xc0008000
Loading: *\b#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##################################
done
Bytes transferred = 2501760 (0x262c80)
get_format
-------- 1 --------
## Booting kernel from Legacy Image at c0008000 ...
Image Name: Linux-3.2.0-rc1+
Created: 2011-11-09 23:23:05 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2501696 Bytes = 2.4 MB
Load Address: 30008000
Entry Point: 30008000
Verifying Checksum ... OK
get_format
-------- 1 --------
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.2.0-rc1+ (####) (gcc version 4.3.3 (GCC) ) #53 PREEMPT
Wed Nov 9 17:23:00 CST 2011
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: CONDOR2416
Memory policy: ECC disabled, Data cache writeback
CPU S3C2416/S3C2450 (id 0x32450003)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666 MHz
CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c050955c, node_mem_map c053e000
Normal zone: 384 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32384 pages, LIFO batch:7
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32384
Kernel command line: console=ttySAC0,115200 loglevel=8
s3cfb=dev:0,depth:16,xres:480,yres:272,vslen:60,hslen:17,left:41,right:68,upper:26,lower:6,pixclock:0
root=/dev/mtdblock4 rw rootfstype=jffs2 ethaddr=12:23:34:88:99:00
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB 64MB = 128MB total
Memory: 124544k/124544k available, 6528k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xcc800000 - 0xf6000000 ( 664 MB)
lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc04992b8 (4677 kB)
.init : 0xc049a000 - 0xc04dd000 ( 268 kB)
.data : 0xc04de000 - 0xc0509c00 ( 175 kB)
.bss : 0xc0509c24 - 0xc053d764 ( 207 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:99
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
timer tcon=00500000, tcnt 2b66, tcfg 00000200,00000000, usec 0000170a
Console: colour dummy device 80x30
Calibrating delay loop... 197.88 BogoMIPS (lpj=98944)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
------------[ cut here ]------------
WARNING: at arch/arm/mach-s3c2416/mach-condor2416.c:875
condor2416_machine_init+0xbc/0x700()
Modules linked in:
[<c000de08>] (unwind_backtrace+0x0/0xec) from [<c001f6e0>]
(warn_slowpath_common+0x48/0x60)
[<c001f6e0>] (warn_slowpath_common+0x48/0x60) from [<c001f714>]
(warn_slowpath_null+0x1c/0x24)
[<c001f714>] (warn_slowpath_null+0x1c/0x24) from [<c049ea9c>]
(condor2416_machine_init+0xbc/0x700)
[<c049ea9c>] (condor2416_machine_init+0xbc/0x700) from [<c049bd64>]
(customize_machine+0x20/0x30)
[<c049bd64>] (customize_machine+0x20/0x30) from [<c00087c0>]
(do_one_initcall+0xa4/0x16c)
[<c00087c0>] (do_one_initcall+0xa4/0x16c) from [<c049a21c>]
(kernel_init+0x7c/0x11c)
[<c049a21c>] (kernel_init+0x7c/0x11c) from [<c0009d94>]
(kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
s3c_fb_setup: option dev:0
s3c_fb_setup: option depth:16
s3c_fb_setup: option xres:480
s3c_fb_setup: option yres:272
s3c_fb_setup: option vslen:60
s3c_fb_setup: option hslen:17
s3c_fb_setup: option left:41
s3c_fb_setup: option right:68
s3c_fb_setup: option upper:26
s3c_fb_setup: option lower:6
s3c_fb_setup: option pixclock:0
Condor2416: Start Set DM9K
S3C Power Management, Copyright 2004 Simtec Electronics
S3C2416: Initializing architecture
S3C2416: IRQ Support
S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
DMA channel 0 at cc804000, irq 88
DMA channel 1 at cc804100, irq 89
DMA channel 2 at cc804200, irq 90
DMA channel 3 at cc804300, irq 91
DMA channel 4 at cc804400, irq 92
DMA channel 5 at cc804500, irq 93
s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333, tin=divclk, base 0
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2410-i2c: slave address 0x10
s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.24.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
s3c-adc s3c24xx-adc: attached adc driver
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 243
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
Console: switching to colour frame buffer device 60x34
s3c-fb s3c-fb: window 0: fb
s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
console [ttySAC0] enabled
s3c2440-uart s3c2440-uart.1: port TX GPIO (13)
s3c2440-uart s3c2440-uart.1: port TX GPIO (12)
s3c2440-uart s3c2440-uart.1: Enable Hi Res Timer
s3c2440-uart s3c2440-uart.1: Port (1) 485 Enabled
s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart s3c2440-uart.1: Initialize TX(1) GPIO
s3c2440-uart s3c2440-uart.1: Initialize RX(1) GPIO
s3c2440-uart s3c2440-uart.2: port TX GPIO (42)
s3c2440-uart s3c2440-uart.2: port TX GPIO (41)
s3c2440-uart s3c2440-uart.2: Enable Hi Res Timer
s3c2440-uart s3c2440-uart.2: Port (2) 485 Enabled
s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
s3c2440-uart s3c2440-uart.2: Initialize TX(2) GPIO
s3c2440-uart s3c2440-uart.2: Initialize RX(2) GPIO
s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
brd: module loaded
at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
mtdoops: mtd device (mtddev=name/number) must be supplied
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c24xx-nand s3c2412-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
s3c24xx-nand s3c2412-nand: System booted from NAND
s3c24xx-nand s3c2412-nand: NAND soft ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 0 at 0x000000000000
Bad eraseblock 1 at 0x000000020000
Bad eraseblock 864 at 0x000006c00000
Bad eraseblock 1304 at 0x00000a300000
Bad eraseblock 1336 at 0x00000a700000
Creating 5 MTD partitions on "NAND":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000060000 : "u-boot-env"
0x000000060000-0x000000560000 : "kernel"
0x000000560000-0x000000660000 : "log"
0x000000660000-0x000010000000 : "root"
dm9000 Ethernet Driver, V1.31
eth0: dm9000a at cc85e300,cc860308 IRQ 53 MAC: 12:23:34:88:99:00 (platform data)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver libusual
mousedev: PS/2 mouse device common for all mice
input: matrix-keypad as /devices/platform/matrix-keypad/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (96000000 Hz)
Registered led device: mmc0::
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
sdhci-pltfm: SDHCI platform and OF driver helper
Registered led device: led1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
samsung_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: uda134x-hifi <-> samsung-i2s.0 mapping ok
ALSA device list:
#0: SAMSUNG_UDA134X
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
s3c-rtc s3c2410-rtc: setting system clock to 2011-11-04 19:30:44 UTC
(1320435044)
usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing init memory: 268K
On Thu, Nov 10, 2011 at 1:59 AM, Heiko Stübner <heiko@sntech.de> wrote:
> Hi Paul,
>
> Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
>> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
> wrote:
>> > Boot past init slow - stalled when using jffs2 also.
>> >
>> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
>> >
>> > <paul.s.schilling@gmail.com> wrote:
>> >> Latest kernel 3.2.0-rc1 appears to break the following processors
>> >> s3c2440 and s3c2416
>> >>
>> >> both appear to stall when init is executed on NFS. Also I lost HSMMC
>> >> on the s3c2416.
>>
>> Could you post a boot log of the kernel on the s3c2440 and s3c2416 boards?
>
> Also, is your out-of-tree kernel code available somewhere? [1]
>
> As my S3C2416 based platform didn't show any problems and has working hsmmc
> with 3.2-rc1 it would be cool to be able to compare both and see if we differ
> somehow.
>
>
> Heiko
>
>
> [1] Mine's at https://gitorious.org/oyo-hack/kernel/commits/topic/board/sg060
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* s3c2440 / s3c2416 broken
@ 2011-11-10 15:57 ` Paul Schilling
0 siblings, 0 replies; 14+ messages in thread
From: Paul Schilling @ 2011-11-10 15:57 UTC (permalink / raw)
To: linux-arm-kernel
Here is my boot log including some u-boot stuff. The trace in my boot
log is concerning a
still broken GPIO bank M access that appears broken.
Thanks,
Paul Schilling
dm9000 i/o: 0x20000300, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 12:23:34:88:99:00
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 10.5.16.68
TFTP from server 10.5.16.63; our IP address is 10.5.16.68
Filename 'schilpa/uImage-dev.bin'.
Load address: 0xc0008000
Loading: *\b#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##################################
done
Bytes transferred = 2501760 (0x262c80)
get_format
-------- 1 --------
## Booting kernel from Legacy Image at c0008000 ...
Image Name: Linux-3.2.0-rc1+
Created: 2011-11-09 23:23:05 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2501696 Bytes = 2.4 MB
Load Address: 30008000
Entry Point: 30008000
Verifying Checksum ... OK
get_format
-------- 1 --------
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.2.0-rc1+ (####) (gcc version 4.3.3 (GCC) ) #53 PREEMPT
Wed Nov 9 17:23:00 CST 2011
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: CONDOR2416
Memory policy: ECC disabled, Data cache writeback
CPU S3C2416/S3C2450 (id 0x32450003)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666 MHz
CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c050955c, node_mem_map c053e000
Normal zone: 384 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32384 pages, LIFO batch:7
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32384
Kernel command line: console=ttySAC0,115200 loglevel=8
s3cfb=dev:0,depth:16,xres:480,yres:272,vslen:60,hslen:17,left:41,right:68,upper:26,lower:6,pixclock:0
root=/dev/mtdblock4 rw rootfstype=jffs2 ethaddr=12:23:34:88:99:00
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB 64MB = 128MB total
Memory: 124544k/124544k available, 6528k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xcc800000 - 0xf6000000 ( 664 MB)
lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc04992b8 (4677 kB)
.init : 0xc049a000 - 0xc04dd000 ( 268 kB)
.data : 0xc04de000 - 0xc0509c00 ( 175 kB)
.bss : 0xc0509c24 - 0xc053d764 ( 207 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:99
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
timer tcon=00500000, tcnt 2b66, tcfg 00000200,00000000, usec 0000170a
Console: colour dummy device 80x30
Calibrating delay loop... 197.88 BogoMIPS (lpj=98944)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
------------[ cut here ]------------
WARNING: at arch/arm/mach-s3c2416/mach-condor2416.c:875
condor2416_machine_init+0xbc/0x700()
Modules linked in:
[<c000de08>] (unwind_backtrace+0x0/0xec) from [<c001f6e0>]
(warn_slowpath_common+0x48/0x60)
[<c001f6e0>] (warn_slowpath_common+0x48/0x60) from [<c001f714>]
(warn_slowpath_null+0x1c/0x24)
[<c001f714>] (warn_slowpath_null+0x1c/0x24) from [<c049ea9c>]
(condor2416_machine_init+0xbc/0x700)
[<c049ea9c>] (condor2416_machine_init+0xbc/0x700) from [<c049bd64>]
(customize_machine+0x20/0x30)
[<c049bd64>] (customize_machine+0x20/0x30) from [<c00087c0>]
(do_one_initcall+0xa4/0x16c)
[<c00087c0>] (do_one_initcall+0xa4/0x16c) from [<c049a21c>]
(kernel_init+0x7c/0x11c)
[<c049a21c>] (kernel_init+0x7c/0x11c) from [<c0009d94>]
(kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
s3c_fb_setup: option dev:0
s3c_fb_setup: option depth:16
s3c_fb_setup: option xres:480
s3c_fb_setup: option yres:272
s3c_fb_setup: option vslen:60
s3c_fb_setup: option hslen:17
s3c_fb_setup: option left:41
s3c_fb_setup: option right:68
s3c_fb_setup: option upper:26
s3c_fb_setup: option lower:6
s3c_fb_setup: option pixclock:0
Condor2416: Start Set DM9K
S3C Power Management, Copyright 2004 Simtec Electronics
S3C2416: Initializing architecture
S3C2416: IRQ Support
S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
DMA channel 0 at cc804000, irq 88
DMA channel 1 at cc804100, irq 89
DMA channel 2 at cc804200, irq 90
DMA channel 3 at cc804300, irq 91
DMA channel 4 at cc804400, irq 92
DMA channel 5 at cc804500, irq 93
s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333, tin=divclk, base 0
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2410-i2c: slave address 0x10
s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.24.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
s3c-adc s3c24xx-adc: attached adc driver
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) (SUMMARY) ? 2001-2006 Red Hat, Inc.
msgmni has been set to 243
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
Console: switching to colour frame buffer device 60x34
s3c-fb s3c-fb: window 0: fb
s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
console [ttySAC0] enabled
s3c2440-uart s3c2440-uart.1: port TX GPIO (13)
s3c2440-uart s3c2440-uart.1: port TX GPIO (12)
s3c2440-uart s3c2440-uart.1: Enable Hi Res Timer
s3c2440-uart s3c2440-uart.1: Port (1) 485 Enabled
s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart s3c2440-uart.1: Initialize TX(1) GPIO
s3c2440-uart s3c2440-uart.1: Initialize RX(1) GPIO
s3c2440-uart s3c2440-uart.2: port TX GPIO (42)
s3c2440-uart s3c2440-uart.2: port TX GPIO (41)
s3c2440-uart s3c2440-uart.2: Enable Hi Res Timer
s3c2440-uart s3c2440-uart.2: Port (2) 485 Enabled
s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
s3c2440-uart s3c2440-uart.2: Initialize TX(2) GPIO
s3c2440-uart s3c2440-uart.2: Initialize RX(2) GPIO
s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
brd: module loaded
at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
mtdoops: mtd device (mtddev=name/number) must be supplied
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c24xx-nand s3c2412-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
s3c24xx-nand s3c2412-nand: System booted from NAND
s3c24xx-nand s3c2412-nand: NAND soft ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 0 at 0x000000000000
Bad eraseblock 1 at 0x000000020000
Bad eraseblock 864 at 0x000006c00000
Bad eraseblock 1304 at 0x00000a300000
Bad eraseblock 1336 at 0x00000a700000
Creating 5 MTD partitions on "NAND":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000060000 : "u-boot-env"
0x000000060000-0x000000560000 : "kernel"
0x000000560000-0x000000660000 : "log"
0x000000660000-0x000010000000 : "root"
dm9000 Ethernet Driver, V1.31
eth0: dm9000a at cc85e300,cc860308 IRQ 53 MAC: 12:23:34:88:99:00 (platform data)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver libusual
mousedev: PS/2 mouse device common for all mice
input: matrix-keypad as /devices/platform/matrix-keypad/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (96000000 Hz)
Registered led device: mmc0::
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
sdhci-pltfm: SDHCI platform and OF driver helper
Registered led device: led1
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
samsung_UDA134X SoC Audio driver
UDA134X SoC Audio Codec
asoc: uda134x-hifi <-> samsung-i2s.0 mapping ok
ALSA device list:
#0: SAMSUNG_UDA134X
TCP cubic registered
NET: Registered protocol family 17
Registering the dns_resolver key type
s3c-rtc s3c2410-rtc: setting system clock to 2011-11-04 19:30:44 UTC
(1320435044)
usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
VFS: Mounted root (jffs2 filesystem) on device 31:4.
Freeing init memory: 268K
On Thu, Nov 10, 2011 at 1:59 AM, Heiko St?bner <heiko@sntech.de> wrote:
> Hi Paul,
>
> Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
>> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
> wrote:
>> > Boot past init slow - stalled when using jffs2 also.
>> >
>> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
>> >
>> > <paul.s.schilling@gmail.com> wrote:
>> >> Latest kernel 3.2.0-rc1 appears to break the following processors
>> >> s3c2440 and s3c2416
>> >>
>> >> both appear to stall when init is executed on NFS. ?Also I ?lost HSMMC
>> >> on the s3c2416.
>>
>> Could you post a boot log of the kernel on the s3c2440 and s3c2416 boards?
>
> Also, is your out-of-tree kernel code available somewhere? [1]
>
> As my S3C2416 based platform didn't show any problems and has working hsmmc
> with 3.2-rc1 it would be cool to be able to compare both and see if we differ
> somehow.
>
>
> Heiko
>
>
> [1] Mine's at https://gitorious.org/oyo-hack/kernel/commits/topic/board/sg060
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: s3c2440 / s3c2416 broken
2011-11-10 15:57 ` Paul Schilling
@ 2011-11-10 16:24 ` Thomas Abraham
-1 siblings, 0 replies; 14+ messages in thread
From: Thomas Abraham @ 2011-11-10 16:24 UTC (permalink / raw)
To: Paul Schilling
Cc: Heiko Stübner, linux-arm-kernel, linux-samsung-soc,
Kukjin Kim, Russell King
Hi Paul,
On 10 November 2011 21:27, Paul Schilling <paul.s.schilling@gmail.com> wrote:
> Here is my boot log including some u-boot stuff. The trace in my boot
> log is concerning a
> still broken GPIO bank M access that appears broken.
Thanks for the log. But I could find out the cause of this issue. I
will check again tomorrow with linux-3.2.0-rc1 on smdk2416. Any luck
when using ramdisk or any clue with git bisect?
Thanks,
Thomas.
>
> Thanks,
> Paul Schilling
>
> dm9000 i/o: 0x20000300, id: 0x90000a46
>
> DM9000: running in 16 bit mode
>
> MAC: 12:23:34:88:99:00
>
> BOOTP broadcast 1
>
> BOOTP broadcast 2
>
> BOOTP broadcast 3
>
> DHCP client bound to address 10.5.16.68
>
> TFTP from server 10.5.16.63; our IP address is 10.5.16.68
>
> Filename 'schilpa/uImage-dev.bin'.
>
> Load address: 0xc0008000
>
> Loading: * #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> ##################################
>
> done
>
> Bytes transferred = 2501760 (0x262c80)
>
> get_format
>
> -------- 1 --------
>
> ## Booting kernel from Legacy Image at c0008000 ...
>
> Image Name: Linux-3.2.0-rc1+
>
> Created: 2011-11-09 23:23:05 UTC
>
> Image Type: ARM Linux Kernel Image (uncompressed)
>
> Data Size: 2501696 Bytes = 2.4 MB
>
> Load Address: 30008000
>
> Entry Point: 30008000
>
> Verifying Checksum ... OK
>
> get_format
>
> -------- 1 --------
>
> Loading Kernel Image ... OK
>
> OK
>
>
>
> Starting kernel ...
>
>
>
> Uncompressing Linux... done, booting the kernel.
>
> Linux version 3.2.0-rc1+ (####) (gcc version 4.3.3 (GCC) ) #53 PREEMPT
> Wed Nov 9 17:23:00 CST 2011
>
> CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
>
> CPU: VIVT data cache, VIVT instruction cache
>
> Machine: CONDOR2416
>
> Memory policy: ECC disabled, Data cache writeback
>
> CPU S3C2416/S3C2450 (id 0x32450003)
>
> S3C24XX Clocks, Copyright 2004 Simtec Electronics
>
> CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666 MHz
>
> CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
>
> On node 0 totalpages: 32768
>
> free_area_init_node: node 0, pgdat c050955c, node_mem_map c053e000
>
> Normal zone: 384 pages used for memmap
>
> Normal zone: 0 pages reserved
>
> Normal zone: 32384 pages, LIFO batch:7
>
> pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
>
> pcpu-alloc: [0] 0
>
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32384
>
> Kernel command line: console=ttySAC0,115200 loglevel=8
> s3cfb=dev:0,depth:16,xres:480,yres:272,vslen:60,hslen:17,left:41,right:68,upper:26,lower:6,pixclock:0
> root=/dev/mtdblock4 rw rootfstype=jffs2 ethaddr=12:23:34:88:99:00
>
> PID hash table entries: 512 (order: -1, 2048 bytes)
>
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
>
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
>
> Memory: 64MB 64MB = 128MB total
>
> Memory: 124544k/124544k available, 6528k reserved, 0K highmem
>
> Virtual kernel memory layout:
>
> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
>
> fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
>
> vmalloc : 0xcc800000 - 0xf6000000 ( 664 MB)
>
> lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
>
> modules : 0xbf000000 - 0xc0000000 ( 16 MB)
>
> .text : 0xc0008000 - 0xc04992b8 (4677 kB)
>
> .init : 0xc049a000 - 0xc04dd000 ( 268 kB)
>
> .data : 0xc04de000 - 0xc0509c00 ( 175 kB)
>
> .bss : 0xc0509c24 - 0xc053d764 ( 207 kB)
>
> SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>
> NR_IRQS:99
>
> irq: clearing subpending status 00000003
>
> irq: clearing subpending status 00000002
>
> timer tcon=00500000, tcnt 2b66, tcfg 00000200,00000000, usec 0000170a
>
> Console: colour dummy device 80x30
>
> Calibrating delay loop... 197.88 BogoMIPS (lpj=98944)
>
> pid_max: default: 32768 minimum: 301
>
> Mount-cache hash table entries: 512
>
> CPU: Testing write buffer coherency: ok
>
> pinctrl core: initialized pinctrl subsystem
>
> NET: Registered protocol family 16
>
> ------------[ cut here ]------------
>
> WARNING: at arch/arm/mach-s3c2416/mach-condor2416.c:875
> condor2416_machine_init+0xbc/0x700()
>
> Modules linked in:
>
> [<c000de08>] (unwind_backtrace+0x0/0xec) from [<c001f6e0>]
> (warn_slowpath_common+0x48/0x60)
>
> [<c001f6e0>] (warn_slowpath_common+0x48/0x60) from [<c001f714>]
> (warn_slowpath_null+0x1c/0x24)
>
> [<c001f714>] (warn_slowpath_null+0x1c/0x24) from [<c049ea9c>]
> (condor2416_machine_init+0xbc/0x700)
>
> [<c049ea9c>] (condor2416_machine_init+0xbc/0x700) from [<c049bd64>]
> (customize_machine+0x20/0x30)
>
> [<c049bd64>] (customize_machine+0x20/0x30) from [<c00087c0>]
> (do_one_initcall+0xa4/0x16c)
>
> [<c00087c0>] (do_one_initcall+0xa4/0x16c) from [<c049a21c>]
> (kernel_init+0x7c/0x11c)
>
> [<c049a21c>] (kernel_init+0x7c/0x11c) from [<c0009d94>]
> (kernel_thread_exit+0x0/0x8)
>
> ---[ end trace 1b75b31a2719ed1c ]---
>
> s3c_fb_setup: option dev:0
>
> s3c_fb_setup: option depth:16
>
> s3c_fb_setup: option xres:480
>
> s3c_fb_setup: option yres:272
>
> s3c_fb_setup: option vslen:60
>
> s3c_fb_setup: option hslen:17
>
> s3c_fb_setup: option left:41
>
> s3c_fb_setup: option right:68
>
> s3c_fb_setup: option upper:26
>
> s3c_fb_setup: option lower:6
>
> s3c_fb_setup: option pixclock:0
>
> Condor2416: Start Set DM9K
>
> S3C Power Management, Copyright 2004 Simtec Electronics
>
> S3C2416: Initializing architecture
>
> S3C2416: IRQ Support
>
> S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
>
> DMA channel 0 at cc804000, irq 88
>
> DMA channel 1 at cc804100, irq 89
>
> DMA channel 2 at cc804200, irq 90
>
> DMA channel 3 at cc804300, irq 91
>
> DMA channel 4 at cc804400, irq 92
>
> DMA channel 5 at cc804500, irq 93
>
> s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333, tin=divclk, base 0
>
> bio: create slab <bio-0> at 0
>
> usbcore: registered new interface driver usbfs
>
> usbcore: registered new interface driver hub
>
> usbcore: registered new device driver usb
>
> s3c-i2c s3c2410-i2c: slave address 0x10
>
> s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
>
> s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
>
> Advanced Linux Sound Architecture Driver Version 1.0.24.
>
> NET: Registered protocol family 2
>
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
>
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
>
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
>
> TCP: Hash tables configured (established 4096 bind 4096)
>
> TCP reno registered
>
> UDP hash table entries: 256 (order: 0, 4096 bytes)
>
> UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
>
> NET: Registered protocol family 1
>
> RPC: Registered named UNIX socket transport module.
>
> RPC: Registered udp transport module.
>
> RPC: Registered tcp transport module.
>
> RPC: Registered tcp NFSv4.1 backchannel transport module.
>
> s3c-adc s3c24xx-adc: attached adc driver
>
> VFS: Disk quotas dquot_6.5.2
>
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>
> JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
>
> msgmni has been set to 243
>
> io scheduler noop registered
>
> io scheduler deadline registered (default)
>
> io scheduler cfq registered
>
> Console: switching to colour frame buffer device 60x34
>
> s3c-fb s3c-fb: window 0: fb
>
> s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
>
> s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
>
> s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
>
> console [ttySAC0] enabled
>
> s3c2440-uart s3c2440-uart.1: port TX GPIO (13)
>
> s3c2440-uart s3c2440-uart.1: port TX GPIO (12)
>
> s3c2440-uart s3c2440-uart.1: Enable Hi Res Timer
>
> s3c2440-uart s3c2440-uart.1: Port (1) 485 Enabled
>
> s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
>
> s3c2440-uart s3c2440-uart.1: Initialize TX(1) GPIO
>
> s3c2440-uart s3c2440-uart.1: Initialize RX(1) GPIO
>
> s3c2440-uart s3c2440-uart.2: port TX GPIO (42)
>
> s3c2440-uart s3c2440-uart.2: port TX GPIO (41)
>
> s3c2440-uart s3c2440-uart.2: Enable Hi Res Timer
>
> s3c2440-uart s3c2440-uart.2: Port (2) 485 Enabled
>
> s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
>
> s3c2440-uart s3c2440-uart.2: Initialize TX(2) GPIO
>
> s3c2440-uart s3c2440-uart.2: Initialize RX(2) GPIO
>
> s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
>
> s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
>
> s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
>
> brd: module loaded
>
> at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
>
> mtdoops: mtd device (mtddev=name/number) must be supplied
>
> S3C24XX NAND Driver, (c) 2004 Simtec Electronics
>
> s3c24xx-nand s3c2412-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
>
> s3c24xx-nand s3c2412-nand: System booted from NAND
>
> s3c24xx-nand s3c2412-nand: NAND soft ECC
>
> NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
> 3,3V 8-bit)
>
> Scanning device for bad blocks
>
> Bad eraseblock 0 at 0x000000000000
>
> Bad eraseblock 1 at 0x000000020000
>
> Bad eraseblock 864 at 0x000006c00000
>
> Bad eraseblock 1304 at 0x00000a300000
>
> Bad eraseblock 1336 at 0x00000a700000
>
> Creating 5 MTD partitions on "NAND":
>
> 0x000000000000-0x000000040000 : "u-boot"
>
> 0x000000040000-0x000000060000 : "u-boot-env"
>
> 0x000000060000-0x000000560000 : "kernel"
>
> 0x000000560000-0x000000660000 : "log"
>
> 0x000000660000-0x000010000000 : "root"
>
> dm9000 Ethernet Driver, V1.31
>
> eth0: dm9000a at cc85e300,cc860308 IRQ 53 MAC: 12:23:34:88:99:00 (platform data)
>
> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>
> s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
>
> s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
>
> s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
>
> hub 1-0:1.0: USB hub found
>
> hub 1-0:1.0: 2 ports detected
>
> usbcore: registered new interface driver libusual
>
> mousedev: PS/2 mouse device common for all mice
>
> input: matrix-keypad as /devices/platform/matrix-keypad/input/input0
>
> S3C24XX RTC, (c) 2004,2006 Simtec Electronics
>
> s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
>
> s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
>
> i2c /dev entries driver
>
> S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
>
> s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
>
> cpuidle: using governor ladder
>
> sdhci: Secure Digital Host Controller Interface driver
>
> sdhci: Copyright(c) Pierre Ossman
>
> s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
>
> s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
>
> s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (96000000 Hz)
>
> Registered led device: mmc0::
>
> mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
>
> sdhci-pltfm: SDHCI platform and OF driver helper
>
> Registered led device: led1
>
> usbcore: registered new interface driver usbhid
>
> usbhid: USB HID core driver
>
> samsung_UDA134X SoC Audio driver
>
> UDA134X SoC Audio Codec
>
> asoc: uda134x-hifi <-> samsung-i2s.0 mapping ok
>
> ALSA device list:
>
> #0: SAMSUNG_UDA134X
>
> TCP cubic registered
>
> NET: Registered protocol family 17
>
> Registering the dns_resolver key type
>
> s3c-rtc s3c2410-rtc: setting system clock to 2011-11-04 19:30:44 UTC
> (1320435044)
>
> usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
>
> VFS: Mounted root (jffs2 filesystem) on device 31:4.
>
> Freeing init memory: 268K
>
> On Thu, Nov 10, 2011 at 1:59 AM, Heiko Stübner <heiko@sntech.de> wrote:
>> Hi Paul,
>>
>> Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
>>> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
>> wrote:
>>> > Boot past init slow - stalled when using jffs2 also.
>>> >
>>> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
>>> >
>>> > <paul.s.schilling@gmail.com> wrote:
>>> >> Latest kernel 3.2.0-rc1 appears to break the following processors
>>> >> s3c2440 and s3c2416
>>> >>
>>> >> both appear to stall when init is executed on NFS. Also I lost HSMMC
>>> >> on the s3c2416.
>>>
>>> Could you post a boot log of the kernel on the s3c2440 and s3c2416 boards?
>>
>> Also, is your out-of-tree kernel code available somewhere? [1]
>>
>> As my S3C2416 based platform didn't show any problems and has working hsmmc
>> with 3.2-rc1 it would be cool to be able to compare both and see if we differ
>> somehow.
>>
>>
>> Heiko
>>
>>
>> [1] Mine's at https://gitorious.org/oyo-hack/kernel/commits/topic/board/sg060
>>
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* s3c2440 / s3c2416 broken
@ 2011-11-10 16:24 ` Thomas Abraham
0 siblings, 0 replies; 14+ messages in thread
From: Thomas Abraham @ 2011-11-10 16:24 UTC (permalink / raw)
To: linux-arm-kernel
Hi Paul,
On 10 November 2011 21:27, Paul Schilling <paul.s.schilling@gmail.com> wrote:
> Here is my boot log including some u-boot stuff. ?The trace in my boot
> log is concerning a
> still broken GPIO bank M access that appears broken.
Thanks for the log. But I could find out the cause of this issue. I
will check again tomorrow with linux-3.2.0-rc1 on smdk2416. Any luck
when using ramdisk or any clue with git bisect?
Thanks,
Thomas.
>
> Thanks,
> Paul Schilling
>
> dm9000 i/o: 0x20000300, id: 0x90000a46
>
> DM9000: running in 16 bit mode
>
> MAC: 12:23:34:88:99:00
>
> BOOTP broadcast 1
>
> BOOTP broadcast 2
>
> BOOTP broadcast 3
>
> DHCP client bound to address 10.5.16.68
>
> TFTP from server 10.5.16.63; our IP address is 10.5.16.68
>
> Filename 'schilpa/uImage-dev.bin'.
>
> Load address: 0xc0008000
>
> Loading: * #################################################################
>
> ? ? ? ? #################################################################
>
> ? ? ? ? #################################################################
>
> ? ? ? ? #################################################################
>
> ? ? ? ? #################################################################
>
> ? ? ? ? #################################################################
>
> ? ? ? ? #################################################################
>
> ? ? ? ? ##################################
>
> done
>
> Bytes transferred = 2501760 (0x262c80)
>
> get_format
>
> -------- 1 --------
>
> ## Booting kernel from Legacy Image at c0008000 ...
>
> ? Image Name: ? Linux-3.2.0-rc1+
>
> ? Created: ? ? ?2011-11-09 ?23:23:05 UTC
>
> ? Image Type: ? ARM Linux Kernel Image (uncompressed)
>
> ? Data Size: ? ?2501696 Bytes = ?2.4 MB
>
> ? Load Address: 30008000
>
> ? Entry Point: ?30008000
>
> ? Verifying Checksum ... OK
>
> get_format
>
> -------- 1 --------
>
> ? Loading Kernel Image ... OK
>
> OK
>
>
>
> Starting kernel ...
>
>
>
> Uncompressing Linux... done, booting the kernel.
>
> Linux version 3.2.0-rc1+ (####) (gcc version 4.3.3 (GCC) ) #53 PREEMPT
> Wed Nov 9 17:23:00 CST 2011
>
> CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
>
> CPU: VIVT data cache, VIVT instruction cache
>
> Machine: CONDOR2416
>
> Memory policy: ECC disabled, Data cache writeback
>
> CPU S3C2416/S3C2450 (id 0x32450003)
>
> S3C24XX Clocks, Copyright 2004 Simtec Electronics
>
> CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666 MHz
>
> CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
>
> On node 0 totalpages: 32768
>
> free_area_init_node: node 0, pgdat c050955c, node_mem_map c053e000
>
> ?Normal zone: 384 pages used for memmap
>
> ?Normal zone: 0 pages reserved
>
> ?Normal zone: 32384 pages, LIFO batch:7
>
> pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
>
> pcpu-alloc: [0] 0
>
> Built 1 zonelists in Zone order, mobility grouping on. ?Total pages: 32384
>
> Kernel command line: console=ttySAC0,115200 loglevel=8
> s3cfb=dev:0,depth:16,xres:480,yres:272,vslen:60,hslen:17,left:41,right:68,upper:26,lower:6,pixclock:0
> root=/dev/mtdblock4 rw rootfstype=jffs2 ethaddr=12:23:34:88:99:00
>
> PID hash table entries: 512 (order: -1, 2048 bytes)
>
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
>
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
>
> Memory: 64MB 64MB = 128MB total
>
> Memory: 124544k/124544k available, 6528k reserved, 0K highmem
>
> Virtual kernel memory layout:
>
> ? ?vector ?: 0xffff0000 - 0xffff1000 ? ( ? 4 kB)
>
> ? ?fixmap ?: 0xfff00000 - 0xfffe0000 ? ( 896 kB)
>
> ? ?vmalloc : 0xcc800000 - 0xf6000000 ? ( 664 MB)
>
> ? ?lowmem ?: 0xc0000000 - 0xcc000000 ? ( 192 MB)
>
> ? ?modules : 0xbf000000 - 0xc0000000 ? ( ?16 MB)
>
> ? ? ?.text : 0xc0008000 - 0xc04992b8 ? (4677 kB)
>
> ? ? ?.init : 0xc049a000 - 0xc04dd000 ? ( 268 kB)
>
> ? ? ?.data : 0xc04de000 - 0xc0509c00 ? ( 175 kB)
>
> ? ? ? .bss : 0xc0509c24 - 0xc053d764 ? ( 207 kB)
>
> SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
>
> NR_IRQS:99
>
> irq: clearing subpending status 00000003
>
> irq: clearing subpending status 00000002
>
> timer tcon=00500000, tcnt 2b66, tcfg 00000200,00000000, usec 0000170a
>
> Console: colour dummy device 80x30
>
> Calibrating delay loop... 197.88 BogoMIPS (lpj=98944)
>
> pid_max: default: 32768 minimum: 301
>
> Mount-cache hash table entries: 512
>
> CPU: Testing write buffer coherency: ok
>
> pinctrl core: initialized pinctrl subsystem
>
> NET: Registered protocol family 16
>
> ------------[ cut here ]------------
>
> WARNING: at arch/arm/mach-s3c2416/mach-condor2416.c:875
> condor2416_machine_init+0xbc/0x700()
>
> Modules linked in:
>
> [<c000de08>] (unwind_backtrace+0x0/0xec) from [<c001f6e0>]
> (warn_slowpath_common+0x48/0x60)
>
> [<c001f6e0>] (warn_slowpath_common+0x48/0x60) from [<c001f714>]
> (warn_slowpath_null+0x1c/0x24)
>
> [<c001f714>] (warn_slowpath_null+0x1c/0x24) from [<c049ea9c>]
> (condor2416_machine_init+0xbc/0x700)
>
> [<c049ea9c>] (condor2416_machine_init+0xbc/0x700) from [<c049bd64>]
> (customize_machine+0x20/0x30)
>
> [<c049bd64>] (customize_machine+0x20/0x30) from [<c00087c0>]
> (do_one_initcall+0xa4/0x16c)
>
> [<c00087c0>] (do_one_initcall+0xa4/0x16c) from [<c049a21c>]
> (kernel_init+0x7c/0x11c)
>
> [<c049a21c>] (kernel_init+0x7c/0x11c) from [<c0009d94>]
> (kernel_thread_exit+0x0/0x8)
>
> ---[ end trace 1b75b31a2719ed1c ]---
>
> s3c_fb_setup: option dev:0
>
> s3c_fb_setup: option depth:16
>
> s3c_fb_setup: option xres:480
>
> s3c_fb_setup: option yres:272
>
> s3c_fb_setup: option vslen:60
>
> s3c_fb_setup: option hslen:17
>
> s3c_fb_setup: option left:41
>
> s3c_fb_setup: option right:68
>
> s3c_fb_setup: option upper:26
>
> s3c_fb_setup: option lower:6
>
> s3c_fb_setup: option pixclock:0
>
> Condor2416: ?Start Set DM9K
>
> S3C Power Management, Copyright 2004 Simtec Electronics
>
> S3C2416: Initializing architecture
>
> S3C2416: IRQ Support
>
> S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
>
> DMA channel 0 at cc804000, irq 88
>
> DMA channel 1 at cc804100, irq 89
>
> DMA channel 2 at cc804200, irq 90
>
> DMA channel 3 at cc804300, irq 91
>
> DMA channel 4 at cc804400, irq 92
>
> DMA channel 5 at cc804500, irq 93
>
> s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333, tin=divclk, base 0
>
> bio: create slab <bio-0> at 0
>
> usbcore: registered new interface driver usbfs
>
> usbcore: registered new interface driver hub
>
> usbcore: registered new device driver usb
>
> s3c-i2c s3c2410-i2c: slave address 0x10
>
> s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
>
> s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
>
> Advanced Linux Sound Architecture Driver Version 1.0.24.
>
> NET: Registered protocol family 2
>
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
>
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
>
> TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
>
> TCP: Hash tables configured (established 4096 bind 4096)
>
> TCP reno registered
>
> UDP hash table entries: 256 (order: 0, 4096 bytes)
>
> UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
>
> NET: Registered protocol family 1
>
> RPC: Registered named UNIX socket transport module.
>
> RPC: Registered udp transport module.
>
> RPC: Registered tcp transport module.
>
> RPC: Registered tcp NFSv4.1 backchannel transport module.
>
> s3c-adc s3c24xx-adc: attached adc driver
>
> VFS: Disk quotas dquot_6.5.2
>
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
>
> JFFS2 version 2.2. (NAND) (SUMMARY) ?? 2001-2006 Red Hat, Inc.
>
> msgmni has been set to 243
>
> io scheduler noop registered
>
> io scheduler deadline registered (default)
>
> io scheduler cfq registered
>
> Console: switching to colour frame buffer device 60x34
>
> s3c-fb s3c-fb: window 0: fb
>
> s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
>
> s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
>
> s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
>
> console [ttySAC0] enabled
>
> s3c2440-uart s3c2440-uart.1: port TX GPIO (13)
>
> s3c2440-uart s3c2440-uart.1: port TX GPIO (12)
>
> s3c2440-uart s3c2440-uart.1: Enable Hi Res Timer
>
> s3c2440-uart s3c2440-uart.1: Port (1) 485 Enabled
>
> s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
>
> s3c2440-uart s3c2440-uart.1: Initialize TX(1) GPIO
>
> s3c2440-uart s3c2440-uart.1: Initialize RX(1) GPIO
>
> s3c2440-uart s3c2440-uart.2: port TX GPIO (42)
>
> s3c2440-uart s3c2440-uart.2: port TX GPIO (41)
>
> s3c2440-uart s3c2440-uart.2: Enable Hi Res Timer
>
> s3c2440-uart s3c2440-uart.2: Port (2) 485 Enabled
>
> s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
>
> s3c2440-uart s3c2440-uart.2: Initialize TX(2) GPIO
>
> s3c2440-uart s3c2440-uart.2: Initialize RX(2) GPIO
>
> s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
>
> s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
>
> s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
>
> brd: module loaded
>
> at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
>
> mtdoops: mtd device (mtddev=name/number) must be supplied
>
> S3C24XX NAND Driver, (c) 2004 Simtec Electronics
>
> s3c24xx-nand s3c2412-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
>
> s3c24xx-nand s3c2412-nand: System booted from NAND
>
> s3c24xx-nand s3c2412-nand: NAND soft ECC
>
> NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
> 3,3V 8-bit)
>
> Scanning device for bad blocks
>
> Bad eraseblock 0 at 0x000000000000
>
> Bad eraseblock 1 at 0x000000020000
>
> Bad eraseblock 864 at 0x000006c00000
>
> Bad eraseblock 1304 at 0x00000a300000
>
> Bad eraseblock 1336 at 0x00000a700000
>
> Creating 5 MTD partitions on "NAND":
>
> 0x000000000000-0x000000040000 : "u-boot"
>
> 0x000000040000-0x000000060000 : "u-boot-env"
>
> 0x000000060000-0x000000560000 : "kernel"
>
> 0x000000560000-0x000000660000 : "log"
>
> 0x000000660000-0x000010000000 : "root"
>
> dm9000 Ethernet Driver, V1.31
>
> eth0: dm9000a at cc85e300,cc860308 IRQ 53 MAC: 12:23:34:88:99:00 (platform data)
>
> ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>
> s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
>
> s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
>
> s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
>
> hub 1-0:1.0: USB hub found
>
> hub 1-0:1.0: 2 ports detected
>
> usbcore: registered new interface driver libusual
>
> mousedev: PS/2 mouse device common for all mice
>
> input: matrix-keypad as /devices/platform/matrix-keypad/input/input0
>
> S3C24XX RTC, (c) 2004,2006 Simtec Electronics
>
> s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
>
> s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
>
> i2c /dev entries driver
>
> S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
>
> s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
>
> cpuidle: using governor ladder
>
> sdhci: Secure Digital Host Controller Interface driver
>
> sdhci: Copyright(c) Pierre Ossman
>
> s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
>
> s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
>
> s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (96000000 Hz)
>
> Registered led device: mmc0::
>
> mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
>
> sdhci-pltfm: SDHCI platform and OF driver helper
>
> Registered led device: led1
>
> usbcore: registered new interface driver usbhid
>
> usbhid: USB HID core driver
>
> samsung_UDA134X SoC Audio driver
>
> UDA134X SoC Audio Codec
>
> asoc: uda134x-hifi <-> samsung-i2s.0 mapping ok
>
> ALSA device list:
>
> ?#0: SAMSUNG_UDA134X
>
> TCP cubic registered
>
> NET: Registered protocol family 17
>
> Registering the dns_resolver key type
>
> s3c-rtc s3c2410-rtc: setting system clock to 2011-11-04 19:30:44 UTC
> (1320435044)
>
> usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
>
> VFS: Mounted root (jffs2 filesystem) on device 31:4.
>
> Freeing init memory: 268K
>
> On Thu, Nov 10, 2011 at 1:59 AM, Heiko St?bner <heiko@sntech.de> wrote:
>> Hi Paul,
>>
>> Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
>>> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
>> wrote:
>>> > Boot past init slow - stalled when using jffs2 also.
>>> >
>>> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
>>> >
>>> > <paul.s.schilling@gmail.com> wrote:
>>> >> Latest kernel 3.2.0-rc1 appears to break the following processors
>>> >> s3c2440 and s3c2416
>>> >>
>>> >> both appear to stall when init is executed on NFS. ?Also I ?lost HSMMC
>>> >> on the s3c2416.
>>>
>>> Could you post a boot log of the kernel on the s3c2440 and s3c2416 boards?
>>
>> Also, is your out-of-tree kernel code available somewhere? [1]
>>
>> As my S3C2416 based platform didn't show any problems and has working hsmmc
>> with 3.2-rc1 it would be cool to be able to compare both and see if we differ
>> somehow.
>>
>>
>> Heiko
>>
>>
>> [1] Mine's at https://gitorious.org/oyo-hack/kernel/commits/topic/board/sg060
>>
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: s3c2440 / s3c2416 broken
2011-11-10 16:24 ` Thomas Abraham
@ 2011-12-01 7:30 ` Kukjin Kim
-1 siblings, 0 replies; 14+ messages in thread
From: Kukjin Kim @ 2011-12-01 7:30 UTC (permalink / raw)
To: 'Thomas Abraham', 'Paul Schilling'
Cc: 'Heiko Stübner', linux-arm-kernel,
'linux-samsung-soc', 'Russell King'
Thomas Abraham wrote:
>
> Hi Paul,
>
> On 10 November 2011 21:27, Paul Schilling <paul.s.schilling@gmail.com>
> wrote:
> > Here is my boot log including some u-boot stuff. The trace in my boot
> > log is concerning a
> > still broken GPIO bank M access that appears broken.
>
> Thanks for the log. But I could find out the cause of this issue. I
> will check again tomorrow with linux-3.2.0-rc1 on smdk2416. Any luck
> when using ramdisk or any clue with git bisect?
>
Hi Paul,
The problem still happens on your board now?
Thanks.
Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.
> >
> > Thanks,
> > Paul Schilling
> >
> > dm9000 i/o: 0x20000300, id: 0x90000a46
> >
> > DM9000: running in 16 bit mode
> >
> > MAC: 12:23:34:88:99:00
> >
> > BOOTP broadcast 1
> >
> > BOOTP broadcast 2
> >
> > BOOTP broadcast 3
> >
> > DHCP client bound to address 10.5.16.68
> >
> > TFTP from server 10.5.16.63; our IP address is 10.5.16.68
> >
> > Filename 'schilpa/uImage-dev.bin'.
> >
> > Load address: 0xc0008000
> >
> > Loading: *
> #################################################################
> >
> >
#################################################################
> >
> >
#################################################################
> >
> >
#################################################################
> >
> >
#################################################################
> >
> >
#################################################################
> >
> >
#################################################################
> >
> > ##################################
> >
> > done
> >
> > Bytes transferred = 2501760 (0x262c80)
> >
> > get_format
> >
> > -------- 1 --------
> >
> > ## Booting kernel from Legacy Image at c0008000 ...
> >
> > Image Name: Linux-3.2.0-rc1+
> >
> > Created: 2011-11-09 23:23:05 UTC
> >
> > Image Type: ARM Linux Kernel Image (uncompressed)
> >
> > Data Size: 2501696 Bytes = 2.4 MB
> >
> > Load Address: 30008000
> >
> > Entry Point: 30008000
> >
> > Verifying Checksum ... OK
> >
> > get_format
> >
> > -------- 1 --------
> >
> > Loading Kernel Image ... OK
> >
> > OK
> >
> >
> >
> > Starting kernel ...
> >
> >
> >
> > Uncompressing Linux... done, booting the kernel.
> >
> > Linux version 3.2.0-rc1+ (####) (gcc version 4.3.3 (GCC) ) #53 PREEMPT
> > Wed Nov 9 17:23:00 CST 2011
> >
> > CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
> >
> > CPU: VIVT data cache, VIVT instruction cache
> >
> > Machine: CONDOR2416
> >
> > Memory policy: ECC disabled, Data cache writeback
> >
> > CPU S3C2416/S3C2450 (id 0x32450003)
> >
> > S3C24XX Clocks, Copyright 2004 Simtec Electronics
> >
> > CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666
> MHz
> >
> > CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
> >
> > On node 0 totalpages: 32768
> >
> > free_area_init_node: node 0, pgdat c050955c, node_mem_map c053e000
> >
> > Normal zone: 384 pages used for memmap
> >
> > Normal zone: 0 pages reserved
> >
> > Normal zone: 32384 pages, LIFO batch:7
> >
> > pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> >
> > pcpu-alloc: [0] 0
> >
> > Built 1 zonelists in Zone order, mobility grouping on. Total pages:
> 32384
> >
> > Kernel command line: console=ttySAC0,115200 loglevel=8
> >
> s3cfb=dev:0,depth:16,xres:480,yres:272,vslen:60,hslen:17,left:41,right:68,
> upper:26,lower:6,pixclock:0
> > root=/dev/mtdblock4 rw rootfstype=jffs2 ethaddr=12:23:34:88:99:00
> >
> > PID hash table entries: 512 (order: -1, 2048 bytes)
> >
> > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> >
> > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> >
> > Memory: 64MB 64MB = 128MB total
> >
> > Memory: 124544k/124544k available, 6528k reserved, 0K highmem
> >
> > Virtual kernel memory layout:
> >
> > vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> >
> > fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
> >
> > vmalloc : 0xcc800000 - 0xf6000000 ( 664 MB)
> >
> > lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
> >
> > modules : 0xbf000000 - 0xc0000000 ( 16 MB)
> >
> > .text : 0xc0008000 - 0xc04992b8 (4677 kB)
> >
> > .init : 0xc049a000 - 0xc04dd000 ( 268 kB)
> >
> > .data : 0xc04de000 - 0xc0509c00 ( 175 kB)
> >
> > .bss : 0xc0509c24 - 0xc053d764 ( 207 kB)
> >
> > SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> >
> > NR_IRQS:99
> >
> > irq: clearing subpending status 00000003
> >
> > irq: clearing subpending status 00000002
> >
> > timer tcon=00500000, tcnt 2b66, tcfg 00000200,00000000, usec 0000170a
> >
> > Console: colour dummy device 80x30
> >
> > Calibrating delay loop... 197.88 BogoMIPS (lpj=98944)
> >
> > pid_max: default: 32768 minimum: 301
> >
> > Mount-cache hash table entries: 512
> >
> > CPU: Testing write buffer coherency: ok
> >
> > pinctrl core: initialized pinctrl subsystem
> >
> > NET: Registered protocol family 16
> >
> > ------------[ cut here ]------------
> >
> > WARNING: at arch/arm/mach-s3c2416/mach-condor2416.c:875
> > condor2416_machine_init+0xbc/0x700()
> >
> > Modules linked in:
> >
> > [<c000de08>] (unwind_backtrace+0x0/0xec) from [<c001f6e0>]
> > (warn_slowpath_common+0x48/0x60)
> >
> > [<c001f6e0>] (warn_slowpath_common+0x48/0x60) from [<c001f714>]
> > (warn_slowpath_null+0x1c/0x24)
> >
> > [<c001f714>] (warn_slowpath_null+0x1c/0x24) from [<c049ea9c>]
> > (condor2416_machine_init+0xbc/0x700)
> >
> > [<c049ea9c>] (condor2416_machine_init+0xbc/0x700) from [<c049bd64>]
> > (customize_machine+0x20/0x30)
> >
> > [<c049bd64>] (customize_machine+0x20/0x30) from [<c00087c0>]
> > (do_one_initcall+0xa4/0x16c)
> >
> > [<c00087c0>] (do_one_initcall+0xa4/0x16c) from [<c049a21c>]
> > (kernel_init+0x7c/0x11c)
> >
> > [<c049a21c>] (kernel_init+0x7c/0x11c) from [<c0009d94>]
> > (kernel_thread_exit+0x0/0x8)
> >
> > ---[ end trace 1b75b31a2719ed1c ]---
> >
> > s3c_fb_setup: option dev:0
> >
> > s3c_fb_setup: option depth:16
> >
> > s3c_fb_setup: option xres:480
> >
> > s3c_fb_setup: option yres:272
> >
> > s3c_fb_setup: option vslen:60
> >
> > s3c_fb_setup: option hslen:17
> >
> > s3c_fb_setup: option left:41
> >
> > s3c_fb_setup: option right:68
> >
> > s3c_fb_setup: option upper:26
> >
> > s3c_fb_setup: option lower:6
> >
> > s3c_fb_setup: option pixclock:0
> >
> > Condor2416: Start Set DM9K
> >
> > S3C Power Management, Copyright 2004 Simtec Electronics
> >
> > S3C2416: Initializing architecture
> >
> > S3C2416: IRQ Support
> >
> > S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
> >
> > DMA channel 0 at cc804000, irq 88
> >
> > DMA channel 1 at cc804100, irq 89
> >
> > DMA channel 2 at cc804200, irq 90
> >
> > DMA channel 3 at cc804300, irq 91
> >
> > DMA channel 4 at cc804400, irq 92
> >
> > DMA channel 5 at cc804500, irq 93
> >
> > s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333,
tin=divclk,
> base 0
> >
> > bio: create slab <bio-0> at 0
> >
> > usbcore: registered new interface driver usbfs
> >
> > usbcore: registered new interface driver hub
> >
> > usbcore: registered new device driver usb
> >
> > s3c-i2c s3c2410-i2c: slave address 0x10
> >
> > s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
> >
> > s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
> >
> > Advanced Linux Sound Architecture Driver Version 1.0.24.
> >
> > NET: Registered protocol family 2
> >
> > IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> >
> > TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> >
> > TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> >
> > TCP: Hash tables configured (established 4096 bind 4096)
> >
> > TCP reno registered
> >
> > UDP hash table entries: 256 (order: 0, 4096 bytes)
> >
> > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> >
> > NET: Registered protocol family 1
> >
> > RPC: Registered named UNIX socket transport module.
> >
> > RPC: Registered udp transport module.
> >
> > RPC: Registered tcp transport module.
> >
> > RPC: Registered tcp NFSv4.1 backchannel transport module.
> >
> > s3c-adc s3c24xx-adc: attached adc driver
> >
> > VFS: Disk quotas dquot_6.5.2
> >
> > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> >
> > JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
> >
> > msgmni has been set to 243
> >
> > io scheduler noop registered
> >
> > io scheduler deadline registered (default)
> >
> > io scheduler cfq registered
> >
> > Console: switching to colour frame buffer device 60x34
> >
> > s3c-fb s3c-fb: window 0: fb
> >
> > s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
> >
> > s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
> >
> > s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
> >
> > console [ttySAC0] enabled
> >
> > s3c2440-uart s3c2440-uart.1: port TX GPIO (13)
> >
> > s3c2440-uart s3c2440-uart.1: port TX GPIO (12)
> >
> > s3c2440-uart s3c2440-uart.1: Enable Hi Res Timer
> >
> > s3c2440-uart s3c2440-uart.1: Port (1) 485 Enabled
> >
> > s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
> >
> > s3c2440-uart s3c2440-uart.1: Initialize TX(1) GPIO
> >
> > s3c2440-uart s3c2440-uart.1: Initialize RX(1) GPIO
> >
> > s3c2440-uart s3c2440-uart.2: port TX GPIO (42)
> >
> > s3c2440-uart s3c2440-uart.2: port TX GPIO (41)
> >
> > s3c2440-uart s3c2440-uart.2: Enable Hi Res Timer
> >
> > s3c2440-uart s3c2440-uart.2: Port (2) 485 Enabled
> >
> > s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
> >
> > s3c2440-uart s3c2440-uart.2: Initialize TX(2) GPIO
> >
> > s3c2440-uart s3c2440-uart.2: Initialize RX(2) GPIO
> >
> > s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
> >
> > s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
> >
> > s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
> >
> > brd: module loaded
> >
> > at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
> >
> > mtdoops: mtd device (mtddev=name/number) must be supplied
> >
> > S3C24XX NAND Driver, (c) 2004 Simtec Electronics
> >
> > s3c24xx-nand s3c2412-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
> >
> > s3c24xx-nand s3c2412-nand: System booted from NAND
> >
> > s3c24xx-nand s3c2412-nand: NAND soft ECC
> >
> > NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
> > 3,3V 8-bit)
> >
> > Scanning device for bad blocks
> >
> > Bad eraseblock 0 at 0x000000000000
> >
> > Bad eraseblock 1 at 0x000000020000
> >
> > Bad eraseblock 864 at 0x000006c00000
> >
> > Bad eraseblock 1304 at 0x00000a300000
> >
> > Bad eraseblock 1336 at 0x00000a700000
> >
> > Creating 5 MTD partitions on "NAND":
> >
> > 0x000000000000-0x000000040000 : "u-boot"
> >
> > 0x000000040000-0x000000060000 : "u-boot-env"
> >
> > 0x000000060000-0x000000560000 : "kernel"
> >
> > 0x000000560000-0x000000660000 : "log"
> >
> > 0x000000660000-0x000010000000 : "root"
> >
> > dm9000 Ethernet Driver, V1.31
> >
> > eth0: dm9000a at cc85e300,cc860308 IRQ 53 MAC: 12:23:34:88:99:00
> (platform data)
> >
> > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> >
> > s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
> >
> > s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
> >
> > s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
> >
> > hub 1-0:1.0: USB hub found
> >
> > hub 1-0:1.0: 2 ports detected
> >
> > usbcore: registered new interface driver libusual
> >
> > mousedev: PS/2 mouse device common for all mice
> >
> > input: matrix-keypad as /devices/platform/matrix-keypad/input/input0
> >
> > S3C24XX RTC, (c) 2004,2006 Simtec Electronics
> >
> > s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
> >
> > s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
> >
> > i2c /dev entries driver
> >
> > S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
> >
> > s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
> >
> > cpuidle: using governor ladder
> >
> > sdhci: Secure Digital Host Controller Interface driver
> >
> > sdhci: Copyright(c) Pierre Ossman
> >
> > s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
> >
> > s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
> >
> > s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (96000000 Hz)
> >
> > Registered led device: mmc0::
> >
> > mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
> >
> > sdhci-pltfm: SDHCI platform and OF driver helper
> >
> > Registered led device: led1
> >
> > usbcore: registered new interface driver usbhid
> >
> > usbhid: USB HID core driver
> >
> > samsung_UDA134X SoC Audio driver
> >
> > UDA134X SoC Audio Codec
> >
> > asoc: uda134x-hifi <-> samsung-i2s.0 mapping ok
> >
> > ALSA device list:
> >
> > #0: SAMSUNG_UDA134X
> >
> > TCP cubic registered
> >
> > NET: Registered protocol family 17
> >
> > Registering the dns_resolver key type
> >
> > s3c-rtc s3c2410-rtc: setting system clock to 2011-11-04 19:30:44 UTC
> > (1320435044)
> >
> > usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
> >
> > VFS: Mounted root (jffs2 filesystem) on device 31:4.
> >
> > Freeing init memory: 268K
> >
> > On Thu, Nov 10, 2011 at 1:59 AM, Heiko Stübner <heiko@sntech.de> wrote:
> >> Hi Paul,
> >>
> >> Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
> >>> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
> >> wrote:
> >>> > Boot past init slow - stalled when using jffs2 also.
> >>> >
> >>> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
> >>> >
> >>> > <paul.s.schilling@gmail.com> wrote:
> >>> >> Latest kernel 3.2.0-rc1 appears to break the following processors
> >>> >> s3c2440 and s3c2416
> >>> >>
> >>> >> both appear to stall when init is executed on NFS. Also I lost
> HSMMC
> >>> >> on the s3c2416.
> >>>
> >>> Could you post a boot log of the kernel on the s3c2440 and s3c2416
> boards?
> >>
> >> Also, is your out-of-tree kernel code available somewhere? [1]
> >>
> >> As my S3C2416 based platform didn't show any problems and has working
> hsmmc
> >> with 3.2-rc1 it would be cool to be able to compare both and see if we
> differ
> >> somehow.
> >>
> >>
> >> Heiko
> >>
> >>
> >> [1] Mine's at https://gitorious.org/oyo-
> hack/kernel/commits/topic/board/sg060
> >>
> >
^ permalink raw reply [flat|nested] 14+ messages in thread
* s3c2440 / s3c2416 broken
@ 2011-12-01 7:30 ` Kukjin Kim
0 siblings, 0 replies; 14+ messages in thread
From: Kukjin Kim @ 2011-12-01 7:30 UTC (permalink / raw)
To: linux-arm-kernel
Thomas Abraham wrote:
>
> Hi Paul,
>
> On 10 November 2011 21:27, Paul Schilling <paul.s.schilling@gmail.com>
> wrote:
> > Here is my boot log including some u-boot stuff. ?The trace in my boot
> > log is concerning a
> > still broken GPIO bank M access that appears broken.
>
> Thanks for the log. But I could find out the cause of this issue. I
> will check again tomorrow with linux-3.2.0-rc1 on smdk2416. Any luck
> when using ramdisk or any clue with git bisect?
>
Hi Paul,
The problem still happens on your board now?
Thanks.
Best regards,
Kgene.
--
Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
SW Solution Development Team, Samsung Electronics Co., Ltd.
> >
> > Thanks,
> > Paul Schilling
> >
> > dm9000 i/o: 0x20000300, id: 0x90000a46
> >
> > DM9000: running in 16 bit mode
> >
> > MAC: 12:23:34:88:99:00
> >
> > BOOTP broadcast 1
> >
> > BOOTP broadcast 2
> >
> > BOOTP broadcast 3
> >
> > DHCP client bound to address 10.5.16.68
> >
> > TFTP from server 10.5.16.63; our IP address is 10.5.16.68
> >
> > Filename 'schilpa/uImage-dev.bin'.
> >
> > Load address: 0xc0008000
> >
> > Loading: *
> #################################################################
> >
> > ? ? ? ?
#################################################################
> >
> > ? ? ? ?
#################################################################
> >
> > ? ? ? ?
#################################################################
> >
> > ? ? ? ?
#################################################################
> >
> > ? ? ? ?
#################################################################
> >
> > ? ? ? ?
#################################################################
> >
> > ? ? ? ? ##################################
> >
> > done
> >
> > Bytes transferred = 2501760 (0x262c80)
> >
> > get_format
> >
> > -------- 1 --------
> >
> > ## Booting kernel from Legacy Image at c0008000 ...
> >
> > ? Image Name: ? Linux-3.2.0-rc1+
> >
> > ? Created: ? ? ?2011-11-09 ?23:23:05 UTC
> >
> > ? Image Type: ? ARM Linux Kernel Image (uncompressed)
> >
> > ? Data Size: ? ?2501696 Bytes = ?2.4 MB
> >
> > ? Load Address: 30008000
> >
> > ? Entry Point: ?30008000
> >
> > ? Verifying Checksum ... OK
> >
> > get_format
> >
> > -------- 1 --------
> >
> > ? Loading Kernel Image ... OK
> >
> > OK
> >
> >
> >
> > Starting kernel ...
> >
> >
> >
> > Uncompressing Linux... done, booting the kernel.
> >
> > Linux version 3.2.0-rc1+ (####) (gcc version 4.3.3 (GCC) ) #53 PREEMPT
> > Wed Nov 9 17:23:00 CST 2011
> >
> > CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
> >
> > CPU: VIVT data cache, VIVT instruction cache
> >
> > Machine: CONDOR2416
> >
> > Memory policy: ECC disabled, Data cache writeback
> >
> > CPU S3C2416/S3C2450 (id 0x32450003)
> >
> > S3C24XX Clocks, Copyright 2004 Simtec Electronics
> >
> > CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666
> MHz
> >
> > CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
> >
> > On node 0 totalpages: 32768
> >
> > free_area_init_node: node 0, pgdat c050955c, node_mem_map c053e000
> >
> > ?Normal zone: 384 pages used for memmap
> >
> > ?Normal zone: 0 pages reserved
> >
> > ?Normal zone: 32384 pages, LIFO batch:7
> >
> > pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> >
> > pcpu-alloc: [0] 0
> >
> > Built 1 zonelists in Zone order, mobility grouping on. ?Total pages:
> 32384
> >
> > Kernel command line: console=ttySAC0,115200 loglevel=8
> >
> s3cfb=dev:0,depth:16,xres:480,yres:272,vslen:60,hslen:17,left:41,right:68,
> upper:26,lower:6,pixclock:0
> > root=/dev/mtdblock4 rw rootfstype=jffs2 ethaddr=12:23:34:88:99:00
> >
> > PID hash table entries: 512 (order: -1, 2048 bytes)
> >
> > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> >
> > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> >
> > Memory: 64MB 64MB = 128MB total
> >
> > Memory: 124544k/124544k available, 6528k reserved, 0K highmem
> >
> > Virtual kernel memory layout:
> >
> > ? ?vector ?: 0xffff0000 - 0xffff1000 ? ( ? 4 kB)
> >
> > ? ?fixmap ?: 0xfff00000 - 0xfffe0000 ? ( 896 kB)
> >
> > ? ?vmalloc : 0xcc800000 - 0xf6000000 ? ( 664 MB)
> >
> > ? ?lowmem ?: 0xc0000000 - 0xcc000000 ? ( 192 MB)
> >
> > ? ?modules : 0xbf000000 - 0xc0000000 ? ( ?16 MB)
> >
> > ? ? ?.text : 0xc0008000 - 0xc04992b8 ? (4677 kB)
> >
> > ? ? ?.init : 0xc049a000 - 0xc04dd000 ? ( 268 kB)
> >
> > ? ? ?.data : 0xc04de000 - 0xc0509c00 ? ( 175 kB)
> >
> > ? ? ? .bss : 0xc0509c24 - 0xc053d764 ? ( 207 kB)
> >
> > SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> >
> > NR_IRQS:99
> >
> > irq: clearing subpending status 00000003
> >
> > irq: clearing subpending status 00000002
> >
> > timer tcon=00500000, tcnt 2b66, tcfg 00000200,00000000, usec 0000170a
> >
> > Console: colour dummy device 80x30
> >
> > Calibrating delay loop... 197.88 BogoMIPS (lpj=98944)
> >
> > pid_max: default: 32768 minimum: 301
> >
> > Mount-cache hash table entries: 512
> >
> > CPU: Testing write buffer coherency: ok
> >
> > pinctrl core: initialized pinctrl subsystem
> >
> > NET: Registered protocol family 16
> >
> > ------------[ cut here ]------------
> >
> > WARNING: at arch/arm/mach-s3c2416/mach-condor2416.c:875
> > condor2416_machine_init+0xbc/0x700()
> >
> > Modules linked in:
> >
> > [<c000de08>] (unwind_backtrace+0x0/0xec) from [<c001f6e0>]
> > (warn_slowpath_common+0x48/0x60)
> >
> > [<c001f6e0>] (warn_slowpath_common+0x48/0x60) from [<c001f714>]
> > (warn_slowpath_null+0x1c/0x24)
> >
> > [<c001f714>] (warn_slowpath_null+0x1c/0x24) from [<c049ea9c>]
> > (condor2416_machine_init+0xbc/0x700)
> >
> > [<c049ea9c>] (condor2416_machine_init+0xbc/0x700) from [<c049bd64>]
> > (customize_machine+0x20/0x30)
> >
> > [<c049bd64>] (customize_machine+0x20/0x30) from [<c00087c0>]
> > (do_one_initcall+0xa4/0x16c)
> >
> > [<c00087c0>] (do_one_initcall+0xa4/0x16c) from [<c049a21c>]
> > (kernel_init+0x7c/0x11c)
> >
> > [<c049a21c>] (kernel_init+0x7c/0x11c) from [<c0009d94>]
> > (kernel_thread_exit+0x0/0x8)
> >
> > ---[ end trace 1b75b31a2719ed1c ]---
> >
> > s3c_fb_setup: option dev:0
> >
> > s3c_fb_setup: option depth:16
> >
> > s3c_fb_setup: option xres:480
> >
> > s3c_fb_setup: option yres:272
> >
> > s3c_fb_setup: option vslen:60
> >
> > s3c_fb_setup: option hslen:17
> >
> > s3c_fb_setup: option left:41
> >
> > s3c_fb_setup: option right:68
> >
> > s3c_fb_setup: option upper:26
> >
> > s3c_fb_setup: option lower:6
> >
> > s3c_fb_setup: option pixclock:0
> >
> > Condor2416: ?Start Set DM9K
> >
> > S3C Power Management, Copyright 2004 Simtec Electronics
> >
> > S3C2416: Initializing architecture
> >
> > S3C2416: IRQ Support
> >
> > S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
> >
> > DMA channel 0 at cc804000, irq 88
> >
> > DMA channel 1 at cc804100, irq 89
> >
> > DMA channel 2 at cc804200, irq 90
> >
> > DMA channel 3 at cc804300, irq 91
> >
> > DMA channel 4 at cc804400, irq 92
> >
> > DMA channel 5 at cc804500, irq 93
> >
> > s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333,
tin=divclk,
> base 0
> >
> > bio: create slab <bio-0> at 0
> >
> > usbcore: registered new interface driver usbfs
> >
> > usbcore: registered new interface driver hub
> >
> > usbcore: registered new device driver usb
> >
> > s3c-i2c s3c2410-i2c: slave address 0x10
> >
> > s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
> >
> > s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
> >
> > Advanced Linux Sound Architecture Driver Version 1.0.24.
> >
> > NET: Registered protocol family 2
> >
> > IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> >
> > TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> >
> > TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> >
> > TCP: Hash tables configured (established 4096 bind 4096)
> >
> > TCP reno registered
> >
> > UDP hash table entries: 256 (order: 0, 4096 bytes)
> >
> > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> >
> > NET: Registered protocol family 1
> >
> > RPC: Registered named UNIX socket transport module.
> >
> > RPC: Registered udp transport module.
> >
> > RPC: Registered tcp transport module.
> >
> > RPC: Registered tcp NFSv4.1 backchannel transport module.
> >
> > s3c-adc s3c24xx-adc: attached adc driver
> >
> > VFS: Disk quotas dquot_6.5.2
> >
> > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> >
> > JFFS2 version 2.2. (NAND) (SUMMARY) ?? 2001-2006 Red Hat, Inc.
> >
> > msgmni has been set to 243
> >
> > io scheduler noop registered
> >
> > io scheduler deadline registered (default)
> >
> > io scheduler cfq registered
> >
> > Console: switching to colour frame buffer device 60x34
> >
> > s3c-fb s3c-fb: window 0: fb
> >
> > s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
> >
> > s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
> >
> > s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
> >
> > console [ttySAC0] enabled
> >
> > s3c2440-uart s3c2440-uart.1: port TX GPIO (13)
> >
> > s3c2440-uart s3c2440-uart.1: port TX GPIO (12)
> >
> > s3c2440-uart s3c2440-uart.1: Enable Hi Res Timer
> >
> > s3c2440-uart s3c2440-uart.1: Port (1) 485 Enabled
> >
> > s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
> >
> > s3c2440-uart s3c2440-uart.1: Initialize TX(1) GPIO
> >
> > s3c2440-uart s3c2440-uart.1: Initialize RX(1) GPIO
> >
> > s3c2440-uart s3c2440-uart.2: port TX GPIO (42)
> >
> > s3c2440-uart s3c2440-uart.2: port TX GPIO (41)
> >
> > s3c2440-uart s3c2440-uart.2: Enable Hi Res Timer
> >
> > s3c2440-uart s3c2440-uart.2: Port (2) 485 Enabled
> >
> > s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
> >
> > s3c2440-uart s3c2440-uart.2: Initialize TX(2) GPIO
> >
> > s3c2440-uart s3c2440-uart.2: Initialize RX(2) GPIO
> >
> > s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
> >
> > s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
> >
> > s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
> >
> > brd: module loaded
> >
> > at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
> >
> > mtdoops: mtd device (mtddev=name/number) must be supplied
> >
> > S3C24XX NAND Driver, (c) 2004 Simtec Electronics
> >
> > s3c24xx-nand s3c2412-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
> >
> > s3c24xx-nand s3c2412-nand: System booted from NAND
> >
> > s3c24xx-nand s3c2412-nand: NAND soft ECC
> >
> > NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
> > 3,3V 8-bit)
> >
> > Scanning device for bad blocks
> >
> > Bad eraseblock 0 at 0x000000000000
> >
> > Bad eraseblock 1 at 0x000000020000
> >
> > Bad eraseblock 864 at 0x000006c00000
> >
> > Bad eraseblock 1304 at 0x00000a300000
> >
> > Bad eraseblock 1336 at 0x00000a700000
> >
> > Creating 5 MTD partitions on "NAND":
> >
> > 0x000000000000-0x000000040000 : "u-boot"
> >
> > 0x000000040000-0x000000060000 : "u-boot-env"
> >
> > 0x000000060000-0x000000560000 : "kernel"
> >
> > 0x000000560000-0x000000660000 : "log"
> >
> > 0x000000660000-0x000010000000 : "root"
> >
> > dm9000 Ethernet Driver, V1.31
> >
> > eth0: dm9000a at cc85e300,cc860308 IRQ 53 MAC: 12:23:34:88:99:00
> (platform data)
> >
> > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> >
> > s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
> >
> > s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
> >
> > s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
> >
> > hub 1-0:1.0: USB hub found
> >
> > hub 1-0:1.0: 2 ports detected
> >
> > usbcore: registered new interface driver libusual
> >
> > mousedev: PS/2 mouse device common for all mice
> >
> > input: matrix-keypad as /devices/platform/matrix-keypad/input/input0
> >
> > S3C24XX RTC, (c) 2004,2006 Simtec Electronics
> >
> > s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
> >
> > s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
> >
> > i2c /dev entries driver
> >
> > S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
> >
> > s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
> >
> > cpuidle: using governor ladder
> >
> > sdhci: Secure Digital Host Controller Interface driver
> >
> > sdhci: Copyright(c) Pierre Ossman
> >
> > s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
> >
> > s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
> >
> > s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (96000000 Hz)
> >
> > Registered led device: mmc0::
> >
> > mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
> >
> > sdhci-pltfm: SDHCI platform and OF driver helper
> >
> > Registered led device: led1
> >
> > usbcore: registered new interface driver usbhid
> >
> > usbhid: USB HID core driver
> >
> > samsung_UDA134X SoC Audio driver
> >
> > UDA134X SoC Audio Codec
> >
> > asoc: uda134x-hifi <-> samsung-i2s.0 mapping ok
> >
> > ALSA device list:
> >
> > ?#0: SAMSUNG_UDA134X
> >
> > TCP cubic registered
> >
> > NET: Registered protocol family 17
> >
> > Registering the dns_resolver key type
> >
> > s3c-rtc s3c2410-rtc: setting system clock to 2011-11-04 19:30:44 UTC
> > (1320435044)
> >
> > usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
> >
> > VFS: Mounted root (jffs2 filesystem) on device 31:4.
> >
> > Freeing init memory: 268K
> >
> > On Thu, Nov 10, 2011 at 1:59 AM, Heiko St?bner <heiko@sntech.de> wrote:
> >> Hi Paul,
> >>
> >> Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
> >>> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
> >> wrote:
> >>> > Boot past init slow - stalled when using jffs2 also.
> >>> >
> >>> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
> >>> >
> >>> > <paul.s.schilling@gmail.com> wrote:
> >>> >> Latest kernel 3.2.0-rc1 appears to break the following processors
> >>> >> s3c2440 and s3c2416
> >>> >>
> >>> >> both appear to stall when init is executed on NFS. ?Also I ?lost
> HSMMC
> >>> >> on the s3c2416.
> >>>
> >>> Could you post a boot log of the kernel on the s3c2440 and s3c2416
> boards?
> >>
> >> Also, is your out-of-tree kernel code available somewhere? [1]
> >>
> >> As my S3C2416 based platform didn't show any problems and has working
> hsmmc
> >> with 3.2-rc1 it would be cool to be able to compare both and see if we
> differ
> >> somehow.
> >>
> >>
> >> Heiko
> >>
> >>
> >> [1] Mine's at https://gitorious.org/oyo-
> hack/kernel/commits/topic/board/sg060
> >>
> >
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: s3c2440 / s3c2416 broken
2011-12-01 7:30 ` Kukjin Kim
@ 2011-12-01 14:09 ` Paul Schilling
-1 siblings, 0 replies; 14+ messages in thread
From: Paul Schilling @ 2011-12-01 14:09 UTC (permalink / raw)
To: Kukjin Kim
Cc: Thomas Abraham, Heiko Stübner, linux-arm-kernel,
linux-samsung-soc, Russell King
I found the problem it was a merging error when I rebased my patch for
my RS485 addition to the UART driver.
I am however still having issues with the frame buffer displaying
horizontal doted lines that shift the next pixels down by a number of
pixels when certain colors are displayed.
Thanks,
Paul
On Thu, Dec 1, 2011 at 1:30 AM, Kukjin Kim <kgene.kim@samsung.com> wrote:
>
> Thomas Abraham wrote:
> >
> > Hi Paul,
> >
> > On 10 November 2011 21:27, Paul Schilling <paul.s.schilling@gmail.com>
> > wrote:
> > > Here is my boot log including some u-boot stuff. The trace in my boot
> > > log is concerning a
> > > still broken GPIO bank M access that appears broken.
> >
> > Thanks for the log. But I could find out the cause of this issue. I
> > will check again tomorrow with linux-3.2.0-rc1 on smdk2416. Any luck
> > when using ramdisk or any clue with git bisect?
> >
>
> Hi Paul,
>
> The problem still happens on your board now?
>
> Thanks.
>
> Best regards,
> Kgene.
> --
> Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
> SW Solution Development Team, Samsung Electronics Co., Ltd.
>
> > >
> > > Thanks,
> > > Paul Schilling
> > >
> > > dm9000 i/o: 0x20000300, id: 0x90000a46
> > >
> > > DM9000: running in 16 bit mode
> > >
> > > MAC: 12:23:34:88:99:00
> > >
> > > BOOTP broadcast 1
> > >
> > > BOOTP broadcast 2
> > >
> > > BOOTP broadcast 3
> > >
> > > DHCP client bound to address 10.5.16.68
> > >
> > > TFTP from server 10.5.16.63; our IP address is 10.5.16.68
> > >
> > > Filename 'schilpa/uImage-dev.bin'.
> > >
> > > Load address: 0xc0008000
> > >
> > > Loading: *
> > #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > > ##################################
> > >
> > > done
> > >
> > > Bytes transferred = 2501760 (0x262c80)
> > >
> > > get_format
> > >
> > > -------- 1 --------
> > >
> > > ## Booting kernel from Legacy Image at c0008000 ...
> > >
> > > Image Name: Linux-3.2.0-rc1+
> > >
> > > Created: 2011-11-09 23:23:05 UTC
> > >
> > > Image Type: ARM Linux Kernel Image (uncompressed)
> > >
> > > Data Size: 2501696 Bytes = 2.4 MB
> > >
> > > Load Address: 30008000
> > >
> > > Entry Point: 30008000
> > >
> > > Verifying Checksum ... OK
> > >
> > > get_format
> > >
> > > -------- 1 --------
> > >
> > > Loading Kernel Image ... OK
> > >
> > > OK
> > >
> > >
> > >
> > > Starting kernel ...
> > >
> > >
> > >
> > > Uncompressing Linux... done, booting the kernel.
> > >
> > > Linux version 3.2.0-rc1+ (####) (gcc version 4.3.3 (GCC) ) #53 PREEMPT
> > > Wed Nov 9 17:23:00 CST 2011
> > >
> > > CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
> > >
> > > CPU: VIVT data cache, VIVT instruction cache
> > >
> > > Machine: CONDOR2416
> > >
> > > Memory policy: ECC disabled, Data cache writeback
> > >
> > > CPU S3C2416/S3C2450 (id 0x32450003)
> > >
> > > S3C24XX Clocks, Copyright 2004 Simtec Electronics
> > >
> > > CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666
> > MHz
> > >
> > > CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
> > >
> > > On node 0 totalpages: 32768
> > >
> > > free_area_init_node: node 0, pgdat c050955c, node_mem_map c053e000
> > >
> > > Normal zone: 384 pages used for memmap
> > >
> > > Normal zone: 0 pages reserved
> > >
> > > Normal zone: 32384 pages, LIFO batch:7
> > >
> > > pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> > >
> > > pcpu-alloc: [0] 0
> > >
> > > Built 1 zonelists in Zone order, mobility grouping on. Total pages:
> > 32384
> > >
> > > Kernel command line: console=ttySAC0,115200 loglevel=8
> > >
> > s3cfb=dev:0,depth:16,xres:480,yres:272,vslen:60,hslen:17,left:41,right:68,
> > upper:26,lower:6,pixclock:0
> > > root=/dev/mtdblock4 rw rootfstype=jffs2 ethaddr=12:23:34:88:99:00
> > >
> > > PID hash table entries: 512 (order: -1, 2048 bytes)
> > >
> > > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> > >
> > > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> > >
> > > Memory: 64MB 64MB = 128MB total
> > >
> > > Memory: 124544k/124544k available, 6528k reserved, 0K highmem
> > >
> > > Virtual kernel memory layout:
> > >
> > > vector : 0xffff0000 - 0xffff1000 ( 4 kB)
> > >
> > > fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
> > >
> > > vmalloc : 0xcc800000 - 0xf6000000 ( 664 MB)
> > >
> > > lowmem : 0xc0000000 - 0xcc000000 ( 192 MB)
> > >
> > > modules : 0xbf000000 - 0xc0000000 ( 16 MB)
> > >
> > > .text : 0xc0008000 - 0xc04992b8 (4677 kB)
> > >
> > > .init : 0xc049a000 - 0xc04dd000 ( 268 kB)
> > >
> > > .data : 0xc04de000 - 0xc0509c00 ( 175 kB)
> > >
> > > .bss : 0xc0509c24 - 0xc053d764 ( 207 kB)
> > >
> > > SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> > >
> > > NR_IRQS:99
> > >
> > > irq: clearing subpending status 00000003
> > >
> > > irq: clearing subpending status 00000002
> > >
> > > timer tcon=00500000, tcnt 2b66, tcfg 00000200,00000000, usec 0000170a
> > >
> > > Console: colour dummy device 80x30
> > >
> > > Calibrating delay loop... 197.88 BogoMIPS (lpj=98944)
> > >
> > > pid_max: default: 32768 minimum: 301
> > >
> > > Mount-cache hash table entries: 512
> > >
> > > CPU: Testing write buffer coherency: ok
> > >
> > > pinctrl core: initialized pinctrl subsystem
> > >
> > > NET: Registered protocol family 16
> > >
> > > ------------[ cut here ]------------
> > >
> > > WARNING: at arch/arm/mach-s3c2416/mach-condor2416.c:875
> > > condor2416_machine_init+0xbc/0x700()
> > >
> > > Modules linked in:
> > >
> > > [<c000de08>] (unwind_backtrace+0x0/0xec) from [<c001f6e0>]
> > > (warn_slowpath_common+0x48/0x60)
> > >
> > > [<c001f6e0>] (warn_slowpath_common+0x48/0x60) from [<c001f714>]
> > > (warn_slowpath_null+0x1c/0x24)
> > >
> > > [<c001f714>] (warn_slowpath_null+0x1c/0x24) from [<c049ea9c>]
> > > (condor2416_machine_init+0xbc/0x700)
> > >
> > > [<c049ea9c>] (condor2416_machine_init+0xbc/0x700) from [<c049bd64>]
> > > (customize_machine+0x20/0x30)
> > >
> > > [<c049bd64>] (customize_machine+0x20/0x30) from [<c00087c0>]
> > > (do_one_initcall+0xa4/0x16c)
> > >
> > > [<c00087c0>] (do_one_initcall+0xa4/0x16c) from [<c049a21c>]
> > > (kernel_init+0x7c/0x11c)
> > >
> > > [<c049a21c>] (kernel_init+0x7c/0x11c) from [<c0009d94>]
> > > (kernel_thread_exit+0x0/0x8)
> > >
> > > ---[ end trace 1b75b31a2719ed1c ]---
> > >
> > > s3c_fb_setup: option dev:0
> > >
> > > s3c_fb_setup: option depth:16
> > >
> > > s3c_fb_setup: option xres:480
> > >
> > > s3c_fb_setup: option yres:272
> > >
> > > s3c_fb_setup: option vslen:60
> > >
> > > s3c_fb_setup: option hslen:17
> > >
> > > s3c_fb_setup: option left:41
> > >
> > > s3c_fb_setup: option right:68
> > >
> > > s3c_fb_setup: option upper:26
> > >
> > > s3c_fb_setup: option lower:6
> > >
> > > s3c_fb_setup: option pixclock:0
> > >
> > > Condor2416: Start Set DM9K
> > >
> > > S3C Power Management, Copyright 2004 Simtec Electronics
> > >
> > > S3C2416: Initializing architecture
> > >
> > > S3C2416: IRQ Support
> > >
> > > S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
> > >
> > > DMA channel 0 at cc804000, irq 88
> > >
> > > DMA channel 1 at cc804100, irq 89
> > >
> > > DMA channel 2 at cc804200, irq 90
> > >
> > > DMA channel 3 at cc804300, irq 91
> > >
> > > DMA channel 4 at cc804400, irq 92
> > >
> > > DMA channel 5 at cc804500, irq 93
> > >
> > > s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333,
> tin=divclk,
> > base 0
> > >
> > > bio: create slab <bio-0> at 0
> > >
> > > usbcore: registered new interface driver usbfs
> > >
> > > usbcore: registered new interface driver hub
> > >
> > > usbcore: registered new device driver usb
> > >
> > > s3c-i2c s3c2410-i2c: slave address 0x10
> > >
> > > s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
> > >
> > > s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
> > >
> > > Advanced Linux Sound Architecture Driver Version 1.0.24.
> > >
> > > NET: Registered protocol family 2
> > >
> > > IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> > >
> > > TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> > >
> > > TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> > >
> > > TCP: Hash tables configured (established 4096 bind 4096)
> > >
> > > TCP reno registered
> > >
> > > UDP hash table entries: 256 (order: 0, 4096 bytes)
> > >
> > > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> > >
> > > NET: Registered protocol family 1
> > >
> > > RPC: Registered named UNIX socket transport module.
> > >
> > > RPC: Registered udp transport module.
> > >
> > > RPC: Registered tcp transport module.
> > >
> > > RPC: Registered tcp NFSv4.1 backchannel transport module.
> > >
> > > s3c-adc s3c24xx-adc: attached adc driver
> > >
> > > VFS: Disk quotas dquot_6.5.2
> > >
> > > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> > >
> > > JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
> > >
> > > msgmni has been set to 243
> > >
> > > io scheduler noop registered
> > >
> > > io scheduler deadline registered (default)
> > >
> > > io scheduler cfq registered
> > >
> > > Console: switching to colour frame buffer device 60x34
> > >
> > > s3c-fb s3c-fb: window 0: fb
> > >
> > > s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
> > >
> > > s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
> > >
> > > s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
> > >
> > > console [ttySAC0] enabled
> > >
> > > s3c2440-uart s3c2440-uart.1: port TX GPIO (13)
> > >
> > > s3c2440-uart s3c2440-uart.1: port TX GPIO (12)
> > >
> > > s3c2440-uart s3c2440-uart.1: Enable Hi Res Timer
> > >
> > > s3c2440-uart s3c2440-uart.1: Port (1) 485 Enabled
> > >
> > > s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
> > >
> > > s3c2440-uart s3c2440-uart.1: Initialize TX(1) GPIO
> > >
> > > s3c2440-uart s3c2440-uart.1: Initialize RX(1) GPIO
> > >
> > > s3c2440-uart s3c2440-uart.2: port TX GPIO (42)
> > >
> > > s3c2440-uart s3c2440-uart.2: port TX GPIO (41)
> > >
> > > s3c2440-uart s3c2440-uart.2: Enable Hi Res Timer
> > >
> > > s3c2440-uart s3c2440-uart.2: Port (2) 485 Enabled
> > >
> > > s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
> > >
> > > s3c2440-uart s3c2440-uart.2: Initialize TX(2) GPIO
> > >
> > > s3c2440-uart s3c2440-uart.2: Initialize RX(2) GPIO
> > >
> > > s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
> > >
> > > s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
> > >
> > > s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
> > >
> > > brd: module loaded
> > >
> > > at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
> > >
> > > mtdoops: mtd device (mtddev=name/number) must be supplied
> > >
> > > S3C24XX NAND Driver, (c) 2004 Simtec Electronics
> > >
> > > s3c24xx-nand s3c2412-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
> > >
> > > s3c24xx-nand s3c2412-nand: System booted from NAND
> > >
> > > s3c24xx-nand s3c2412-nand: NAND soft ECC
> > >
> > > NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
> > > 3,3V 8-bit)
> > >
> > > Scanning device for bad blocks
> > >
> > > Bad eraseblock 0 at 0x000000000000
> > >
> > > Bad eraseblock 1 at 0x000000020000
> > >
> > > Bad eraseblock 864 at 0x000006c00000
> > >
> > > Bad eraseblock 1304 at 0x00000a300000
> > >
> > > Bad eraseblock 1336 at 0x00000a700000
> > >
> > > Creating 5 MTD partitions on "NAND":
> > >
> > > 0x000000000000-0x000000040000 : "u-boot"
> > >
> > > 0x000000040000-0x000000060000 : "u-boot-env"
> > >
> > > 0x000000060000-0x000000560000 : "kernel"
> > >
> > > 0x000000560000-0x000000660000 : "log"
> > >
> > > 0x000000660000-0x000010000000 : "root"
> > >
> > > dm9000 Ethernet Driver, V1.31
> > >
> > > eth0: dm9000a at cc85e300,cc860308 IRQ 53 MAC: 12:23:34:88:99:00
> > (platform data)
> > >
> > > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> > >
> > > s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
> > >
> > > s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
> > >
> > > s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
> > >
> > > hub 1-0:1.0: USB hub found
> > >
> > > hub 1-0:1.0: 2 ports detected
> > >
> > > usbcore: registered new interface driver libusual
> > >
> > > mousedev: PS/2 mouse device common for all mice
> > >
> > > input: matrix-keypad as /devices/platform/matrix-keypad/input/input0
> > >
> > > S3C24XX RTC, (c) 2004,2006 Simtec Electronics
> > >
> > > s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
> > >
> > > s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
> > >
> > > i2c /dev entries driver
> > >
> > > S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
> > >
> > > s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
> > >
> > > cpuidle: using governor ladder
> > >
> > > sdhci: Secure Digital Host Controller Interface driver
> > >
> > > sdhci: Copyright(c) Pierre Ossman
> > >
> > > s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
> > >
> > > s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
> > >
> > > s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (96000000 Hz)
> > >
> > > Registered led device: mmc0::
> > >
> > > mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
> > >
> > > sdhci-pltfm: SDHCI platform and OF driver helper
> > >
> > > Registered led device: led1
> > >
> > > usbcore: registered new interface driver usbhid
> > >
> > > usbhid: USB HID core driver
> > >
> > > samsung_UDA134X SoC Audio driver
> > >
> > > UDA134X SoC Audio Codec
> > >
> > > asoc: uda134x-hifi <-> samsung-i2s.0 mapping ok
> > >
> > > ALSA device list:
> > >
> > > #0: SAMSUNG_UDA134X
> > >
> > > TCP cubic registered
> > >
> > > NET: Registered protocol family 17
> > >
> > > Registering the dns_resolver key type
> > >
> > > s3c-rtc s3c2410-rtc: setting system clock to 2011-11-04 19:30:44 UTC
> > > (1320435044)
> > >
> > > usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
> > >
> > > VFS: Mounted root (jffs2 filesystem) on device 31:4.
> > >
> > > Freeing init memory: 268K
> > >
> > > On Thu, Nov 10, 2011 at 1:59 AM, Heiko Stübner <heiko@sntech.de> wrote:
> > >> Hi Paul,
> > >>
> > >> Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
> > >>> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
> > >> wrote:
> > >>> > Boot past init slow - stalled when using jffs2 also.
> > >>> >
> > >>> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
> > >>> >
> > >>> > <paul.s.schilling@gmail.com> wrote:
> > >>> >> Latest kernel 3.2.0-rc1 appears to break the following processors
> > >>> >> s3c2440 and s3c2416
> > >>> >>
> > >>> >> both appear to stall when init is executed on NFS. Also I lost
> > HSMMC
> > >>> >> on the s3c2416.
> > >>>
> > >>> Could you post a boot log of the kernel on the s3c2440 and s3c2416
> > boards?
> > >>
> > >> Also, is your out-of-tree kernel code available somewhere? [1]
> > >>
> > >> As my S3C2416 based platform didn't show any problems and has working
> > hsmmc
> > >> with 3.2-rc1 it would be cool to be able to compare both and see if we
> > differ
> > >> somehow.
> > >>
> > >>
> > >> Heiko
> > >>
> > >>
> > >> [1] Mine's at https://gitorious.org/oyo-
> > hack/kernel/commits/topic/board/sg060
> > >>
> > >
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* s3c2440 / s3c2416 broken
@ 2011-12-01 14:09 ` Paul Schilling
0 siblings, 0 replies; 14+ messages in thread
From: Paul Schilling @ 2011-12-01 14:09 UTC (permalink / raw)
To: linux-arm-kernel
I found the problem it was a merging error when I rebased my patch for
my RS485 addition to the UART driver.
I am however still having issues with the frame buffer displaying
horizontal doted lines that shift the next pixels?down by a number of
pixels when certain colors are displayed.
Thanks,
Paul
On Thu, Dec 1, 2011 at 1:30 AM, Kukjin Kim <kgene.kim@samsung.com> wrote:
>
> Thomas Abraham wrote:
> >
> > Hi Paul,
> >
> > On 10 November 2011 21:27, Paul Schilling <paul.s.schilling@gmail.com>
> > wrote:
> > > Here is my boot log including some u-boot stuff. ?The trace in my boot
> > > log is concerning a
> > > still broken GPIO bank M access that appears broken.
> >
> > Thanks for the log. But I could find out the cause of this issue. I
> > will check again tomorrow with linux-3.2.0-rc1 on smdk2416. Any luck
> > when using ramdisk or any clue with git bisect?
> >
>
> Hi Paul,
>
> The problem still happens on your board now?
>
> Thanks.
>
> Best regards,
> Kgene.
> --
> Kukjin Kim <kgene.kim@samsung.com>, Senior Engineer,
> SW Solution Development Team, Samsung Electronics Co., Ltd.
>
> > >
> > > Thanks,
> > > Paul Schilling
> > >
> > > dm9000 i/o: 0x20000300, id: 0x90000a46
> > >
> > > DM9000: running in 16 bit mode
> > >
> > > MAC: 12:23:34:88:99:00
> > >
> > > BOOTP broadcast 1
> > >
> > > BOOTP broadcast 2
> > >
> > > BOOTP broadcast 3
> > >
> > > DHCP client bound to address 10.5.16.68
> > >
> > > TFTP from server 10.5.16.63; our IP address is 10.5.16.68
> > >
> > > Filename 'schilpa/uImage-dev.bin'.
> > >
> > > Load address: 0xc0008000
> > >
> > > Loading: *
> > #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > >
> #################################################################
> > >
> > > ? ? ? ? ##################################
> > >
> > > done
> > >
> > > Bytes transferred = 2501760 (0x262c80)
> > >
> > > get_format
> > >
> > > -------- 1 --------
> > >
> > > ## Booting kernel from Legacy Image at c0008000 ...
> > >
> > > ? Image Name: ? Linux-3.2.0-rc1+
> > >
> > > ? Created: ? ? ?2011-11-09 ?23:23:05 UTC
> > >
> > > ? Image Type: ? ARM Linux Kernel Image (uncompressed)
> > >
> > > ? Data Size: ? ?2501696 Bytes = ?2.4 MB
> > >
> > > ? Load Address: 30008000
> > >
> > > ? Entry Point: ?30008000
> > >
> > > ? Verifying Checksum ... OK
> > >
> > > get_format
> > >
> > > -------- 1 --------
> > >
> > > ? Loading Kernel Image ... OK
> > >
> > > OK
> > >
> > >
> > >
> > > Starting kernel ...
> > >
> > >
> > >
> > > Uncompressing Linux... done, booting the kernel.
> > >
> > > Linux version 3.2.0-rc1+ (####) (gcc version 4.3.3 (GCC) ) #53 PREEMPT
> > > Wed Nov 9 17:23:00 CST 2011
> > >
> > > CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
> > >
> > > CPU: VIVT data cache, VIVT instruction cache
> > >
> > > Machine: CONDOR2416
> > >
> > > Memory policy: ECC disabled, Data cache writeback
> > >
> > > CPU S3C2416/S3C2450 (id 0x32450003)
> > >
> > > S3C24XX Clocks, Copyright 2004 Simtec Electronics
> > >
> > > CPU: MPLL on 800.000 MHz, cpu 400.000 MHz, mem 133.333 MHz, pclk 66.666
> > MHz
> > >
> > > CPU: EPLL on 96.000 MHz, usb-bus 48.000 MHz
> > >
> > > On node 0 totalpages: 32768
> > >
> > > free_area_init_node: node 0, pgdat c050955c, node_mem_map c053e000
> > >
> > > ?Normal zone: 384 pages used for memmap
> > >
> > > ?Normal zone: 0 pages reserved
> > >
> > > ?Normal zone: 32384 pages, LIFO batch:7
> > >
> > > pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> > >
> > > pcpu-alloc: [0] 0
> > >
> > > Built 1 zonelists in Zone order, mobility grouping on. ?Total pages:
> > 32384
> > >
> > > Kernel command line: console=ttySAC0,115200 loglevel=8
> > >
> > s3cfb=dev:0,depth:16,xres:480,yres:272,vslen:60,hslen:17,left:41,right:68,
> > upper:26,lower:6,pixclock:0
> > > root=/dev/mtdblock4 rw rootfstype=jffs2 ethaddr=12:23:34:88:99:00
> > >
> > > PID hash table entries: 512 (order: -1, 2048 bytes)
> > >
> > > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> > >
> > > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> > >
> > > Memory: 64MB 64MB = 128MB total
> > >
> > > Memory: 124544k/124544k available, 6528k reserved, 0K highmem
> > >
> > > Virtual kernel memory layout:
> > >
> > > ? ?vector ?: 0xffff0000 - 0xffff1000 ? ( ? 4 kB)
> > >
> > > ? ?fixmap ?: 0xfff00000 - 0xfffe0000 ? ( 896 kB)
> > >
> > > ? ?vmalloc : 0xcc800000 - 0xf6000000 ? ( 664 MB)
> > >
> > > ? ?lowmem ?: 0xc0000000 - 0xcc000000 ? ( 192 MB)
> > >
> > > ? ?modules : 0xbf000000 - 0xc0000000 ? ( ?16 MB)
> > >
> > > ? ? ?.text : 0xc0008000 - 0xc04992b8 ? (4677 kB)
> > >
> > > ? ? ?.init : 0xc049a000 - 0xc04dd000 ? ( 268 kB)
> > >
> > > ? ? ?.data : 0xc04de000 - 0xc0509c00 ? ( 175 kB)
> > >
> > > ? ? ? .bss : 0xc0509c24 - 0xc053d764 ? ( 207 kB)
> > >
> > > SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
> > >
> > > NR_IRQS:99
> > >
> > > irq: clearing subpending status 00000003
> > >
> > > irq: clearing subpending status 00000002
> > >
> > > timer tcon=00500000, tcnt 2b66, tcfg 00000200,00000000, usec 0000170a
> > >
> > > Console: colour dummy device 80x30
> > >
> > > Calibrating delay loop... 197.88 BogoMIPS (lpj=98944)
> > >
> > > pid_max: default: 32768 minimum: 301
> > >
> > > Mount-cache hash table entries: 512
> > >
> > > CPU: Testing write buffer coherency: ok
> > >
> > > pinctrl core: initialized pinctrl subsystem
> > >
> > > NET: Registered protocol family 16
> > >
> > > ------------[ cut here ]------------
> > >
> > > WARNING: at arch/arm/mach-s3c2416/mach-condor2416.c:875
> > > condor2416_machine_init+0xbc/0x700()
> > >
> > > Modules linked in:
> > >
> > > [<c000de08>] (unwind_backtrace+0x0/0xec) from [<c001f6e0>]
> > > (warn_slowpath_common+0x48/0x60)
> > >
> > > [<c001f6e0>] (warn_slowpath_common+0x48/0x60) from [<c001f714>]
> > > (warn_slowpath_null+0x1c/0x24)
> > >
> > > [<c001f714>] (warn_slowpath_null+0x1c/0x24) from [<c049ea9c>]
> > > (condor2416_machine_init+0xbc/0x700)
> > >
> > > [<c049ea9c>] (condor2416_machine_init+0xbc/0x700) from [<c049bd64>]
> > > (customize_machine+0x20/0x30)
> > >
> > > [<c049bd64>] (customize_machine+0x20/0x30) from [<c00087c0>]
> > > (do_one_initcall+0xa4/0x16c)
> > >
> > > [<c00087c0>] (do_one_initcall+0xa4/0x16c) from [<c049a21c>]
> > > (kernel_init+0x7c/0x11c)
> > >
> > > [<c049a21c>] (kernel_init+0x7c/0x11c) from [<c0009d94>]
> > > (kernel_thread_exit+0x0/0x8)
> > >
> > > ---[ end trace 1b75b31a2719ed1c ]---
> > >
> > > s3c_fb_setup: option dev:0
> > >
> > > s3c_fb_setup: option depth:16
> > >
> > > s3c_fb_setup: option xres:480
> > >
> > > s3c_fb_setup: option yres:272
> > >
> > > s3c_fb_setup: option vslen:60
> > >
> > > s3c_fb_setup: option hslen:17
> > >
> > > s3c_fb_setup: option left:41
> > >
> > > s3c_fb_setup: option right:68
> > >
> > > s3c_fb_setup: option upper:26
> > >
> > > s3c_fb_setup: option lower:6
> > >
> > > s3c_fb_setup: option pixclock:0
> > >
> > > Condor2416: ?Start Set DM9K
> > >
> > > S3C Power Management, Copyright 2004 Simtec Electronics
> > >
> > > S3C2416: Initializing architecture
> > >
> > > S3C2416: IRQ Support
> > >
> > > S3C24XX DMA Driver, Copyright 2003-2006 Simtec Electronics
> > >
> > > DMA channel 0 at cc804000, irq 88
> > >
> > > DMA channel 1 at cc804100, irq 89
> > >
> > > DMA channel 2 at cc804200, irq 90
> > >
> > > DMA channel 3 at cc804300, irq 91
> > >
> > > DMA channel 4 at cc804400, irq 92
> > >
> > > DMA channel 5 at cc804500, irq 93
> > >
> > > s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333,
> tin=divclk,
> > base 0
> > >
> > > bio: create slab <bio-0> at 0
> > >
> > > usbcore: registered new interface driver usbfs
> > >
> > > usbcore: registered new interface driver hub
> > >
> > > usbcore: registered new device driver usb
> > >
> > > s3c-i2c s3c2410-i2c: slave address 0x10
> > >
> > > s3c-i2c s3c2410-i2c: bus frequency set to 65 KHz
> > >
> > > s3c-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
> > >
> > > Advanced Linux Sound Architecture Driver Version 1.0.24.
> > >
> > > NET: Registered protocol family 2
> > >
> > > IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> > >
> > > TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> > >
> > > TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
> > >
> > > TCP: Hash tables configured (established 4096 bind 4096)
> > >
> > > TCP reno registered
> > >
> > > UDP hash table entries: 256 (order: 0, 4096 bytes)
> > >
> > > UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
> > >
> > > NET: Registered protocol family 1
> > >
> > > RPC: Registered named UNIX socket transport module.
> > >
> > > RPC: Registered udp transport module.
> > >
> > > RPC: Registered tcp transport module.
> > >
> > > RPC: Registered tcp NFSv4.1 backchannel transport module.
> > >
> > > s3c-adc s3c24xx-adc: attached adc driver
> > >
> > > VFS: Disk quotas dquot_6.5.2
> > >
> > > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> > >
> > > JFFS2 version 2.2. (NAND) (SUMMARY) ?? 2001-2006 Red Hat, Inc.
> > >
> > > msgmni has been set to 243
> > >
> > > io scheduler noop registered
> > >
> > > io scheduler deadline registered (default)
> > >
> > > io scheduler cfq registered
> > >
> > > Console: switching to colour frame buffer device 60x34
> > >
> > > s3c-fb s3c-fb: window 0: fb
> > >
> > > s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
> > >
> > > s3c2440-uart s3c2440-uart.0: port TX GPIO (-1)
> > >
> > > s3c2440-uart.0: ttySAC0 at MMIO 0x50000000 (irq = 70) is a S3C2440
> > >
> > > console [ttySAC0] enabled
> > >
> > > s3c2440-uart s3c2440-uart.1: port TX GPIO (13)
> > >
> > > s3c2440-uart s3c2440-uart.1: port TX GPIO (12)
> > >
> > > s3c2440-uart s3c2440-uart.1: Enable Hi Res Timer
> > >
> > > s3c2440-uart s3c2440-uart.1: Port (1) 485 Enabled
> > >
> > > s3c2440-uart.1: ttySAC1 at MMIO 0x50004000 (irq = 73) is a S3C2440
> > >
> > > s3c2440-uart s3c2440-uart.1: Initialize TX(1) GPIO
> > >
> > > s3c2440-uart s3c2440-uart.1: Initialize RX(1) GPIO
> > >
> > > s3c2440-uart s3c2440-uart.2: port TX GPIO (42)
> > >
> > > s3c2440-uart s3c2440-uart.2: port TX GPIO (41)
> > >
> > > s3c2440-uart s3c2440-uart.2: Enable Hi Res Timer
> > >
> > > s3c2440-uart s3c2440-uart.2: Port (2) 485 Enabled
> > >
> > > s3c2440-uart.2: ttySAC2 at MMIO 0x50008000 (irq = 76) is a S3C2440
> > >
> > > s3c2440-uart s3c2440-uart.2: Initialize TX(2) GPIO
> > >
> > > s3c2440-uart s3c2440-uart.2: Initialize RX(2) GPIO
> > >
> > > s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
> > >
> > > s3c2440-uart s3c2440-uart.3: port TX GPIO (-1)
> > >
> > > s3c2440-uart.3: ttySAC3 at MMIO 0x5000c000 (irq = 94) is a S3C2440
> > >
> > > brd: module loaded
> > >
> > > at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
> > >
> > > mtdoops: mtd device (mtddev=name/number) must be supplied
> > >
> > > S3C24XX NAND Driver, (c) 2004 Simtec Electronics
> > >
> > > s3c24xx-nand s3c2412-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
> > >
> > > s3c24xx-nand s3c2412-nand: System booted from NAND
> > >
> > > s3c24xx-nand s3c2412-nand: NAND soft ECC
> > >
> > > NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB
> > > 3,3V 8-bit)
> > >
> > > Scanning device for bad blocks
> > >
> > > Bad eraseblock 0 at 0x000000000000
> > >
> > > Bad eraseblock 1 at 0x000000020000
> > >
> > > Bad eraseblock 864 at 0x000006c00000
> > >
> > > Bad eraseblock 1304 at 0x00000a300000
> > >
> > > Bad eraseblock 1336 at 0x00000a700000
> > >
> > > Creating 5 MTD partitions on "NAND":
> > >
> > > 0x000000000000-0x000000040000 : "u-boot"
> > >
> > > 0x000000040000-0x000000060000 : "u-boot-env"
> > >
> > > 0x000000060000-0x000000560000 : "kernel"
> > >
> > > 0x000000560000-0x000000660000 : "log"
> > >
> > > 0x000000660000-0x000010000000 : "root"
> > >
> > > dm9000 Ethernet Driver, V1.31
> > >
> > > eth0: dm9000a at cc85e300,cc860308 IRQ 53 MAC: 12:23:34:88:99:00
> > (platform data)
> > >
> > > ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
> > >
> > > s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
> > >
> > > s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
> > >
> > > s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
> > >
> > > hub 1-0:1.0: USB hub found
> > >
> > > hub 1-0:1.0: 2 ports detected
> > >
> > > usbcore: registered new interface driver libusual
> > >
> > > mousedev: PS/2 mouse device common for all mice
> > >
> > > input: matrix-keypad as /devices/platform/matrix-keypad/input/input0
> > >
> > > S3C24XX RTC, (c) 2004,2006 Simtec Electronics
> > >
> > > s3c-rtc s3c2410-rtc: rtc disabled, re-enabling
> > >
> > > s3c-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
> > >
> > > i2c /dev entries driver
> > >
> > > S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
> > >
> > > s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
> > >
> > > cpuidle: using governor ladder
> > >
> > > sdhci: Secure Digital Host Controller Interface driver
> > >
> > > sdhci: Copyright(c) Pierre Ossman
> > >
> > > s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133333333 Hz)
> > >
> > > s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133333333 Hz)
> > >
> > > s3c-sdhci s3c-sdhci.1: clock source 2: hsmmc-if (96000000 Hz)
> > >
> > > Registered led device: mmc0::
> > >
> > > mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
> > >
> > > sdhci-pltfm: SDHCI platform and OF driver helper
> > >
> > > Registered led device: led1
> > >
> > > usbcore: registered new interface driver usbhid
> > >
> > > usbhid: USB HID core driver
> > >
> > > samsung_UDA134X SoC Audio driver
> > >
> > > UDA134X SoC Audio Codec
> > >
> > > asoc: uda134x-hifi <-> samsung-i2s.0 mapping ok
> > >
> > > ALSA device list:
> > >
> > > ?#0: SAMSUNG_UDA134X
> > >
> > > TCP cubic registered
> > >
> > > NET: Registered protocol family 17
> > >
> > > Registering the dns_resolver key type
> > >
> > > s3c-rtc s3c2410-rtc: setting system clock to 2011-11-04 19:30:44 UTC
> > > (1320435044)
> > >
> > > usb 1-1: new full-speed USB device number 2 using s3c2410-ohci
> > >
> > > VFS: Mounted root (jffs2 filesystem) on device 31:4.
> > >
> > > Freeing init memory: 268K
> > >
> > > On Thu, Nov 10, 2011 at 1:59 AM, Heiko St?bner <heiko@sntech.de> wrote:
> > >> Hi Paul,
> > >>
> > >> Am Donnerstag, 10. November 2011, 01:14:59 schrieb Thomas Abraham:
> > >>> On 10 November 2011 05:00, Paul Schilling <paul.s.schilling@gmail.com>
> > >> wrote:
> > >>> > Boot past init slow - stalled when using jffs2 also.
> > >>> >
> > >>> > On Wed, Nov 9, 2011 at 4:12 PM, Paul Schilling
> > >>> >
> > >>> > <paul.s.schilling@gmail.com> wrote:
> > >>> >> Latest kernel 3.2.0-rc1 appears to break the following processors
> > >>> >> s3c2440 and s3c2416
> > >>> >>
> > >>> >> both appear to stall when init is executed on NFS. ?Also I ?lost
> > HSMMC
> > >>> >> on the s3c2416.
> > >>>
> > >>> Could you post a boot log of the kernel on the s3c2440 and s3c2416
> > boards?
> > >>
> > >> Also, is your out-of-tree kernel code available somewhere? [1]
> > >>
> > >> As my S3C2416 based platform didn't show any problems and has working
> > hsmmc
> > >> with 3.2-rc1 it would be cool to be able to compare both and see if we
> > differ
> > >> somehow.
> > >>
> > >>
> > >> Heiko
> > >>
> > >>
> > >> [1] Mine's at https://gitorious.org/oyo-
> > hack/kernel/commits/topic/board/sg060
> > >>
> > >
>
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2011-12-01 14:09 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-11-09 22:12 s3c2440 / s3c2416 broken Paul Schilling
2011-11-09 23:30 ` Paul Schilling
2011-11-10 0:14 ` Thomas Abraham
2011-11-10 0:14 ` Thomas Abraham
2011-11-10 7:59 ` Heiko Stübner
2011-11-10 7:59 ` Heiko Stübner
2011-11-10 15:57 ` Paul Schilling
2011-11-10 15:57 ` Paul Schilling
2011-11-10 16:24 ` Thomas Abraham
2011-11-10 16:24 ` Thomas Abraham
2011-12-01 7:30 ` Kukjin Kim
2011-12-01 7:30 ` Kukjin Kim
2011-12-01 14:09 ` Paul Schilling
2011-12-01 14:09 ` Paul Schilling
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.