Re: [alsa-devel] [PATCH] hda - fail ELD reading early

[Wu Fengguang <fengguang.wu@intel.com>]

On Tue, Nov 22, 2011 at 06:39:53PM +0800, Takashi Iwai wrote:
> At Tue, 22 Nov 2011 16:46:23 +0800,
> Wu Fengguang wrote:
> > 
> > With the ELD repoll mechanism, we can (and should) fail the ELD reading
> > immediately when find something obviously wrong and let the caller retry
> > after some delay.
> > 
> > Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
> > ---
> >  sound/pci/hda/hda_eld.c |   28 +++++++++++++++++++---------
> >  1 file changed, 19 insertions(+), 9 deletions(-)
> > 
> > --- linux.orig/sound/pci/hda/hda_eld.c	2011-11-22 16:02:58.000000000 +0800
> > +++ linux/sound/pci/hda/hda_eld.c	2011-11-22 16:36:10.000000000 +0800
> > @@ -347,18 +347,28 @@ int snd_hdmi_get_eld(struct hdmi_eld *el
> >  
> >  	for (i = 0; i < size; i++) {
> >  		unsigned int val = hdmi_get_eld_data(codec, nid, i);
> > +		/*
> > +		 * Graphics driver might be writing to ELD buffer right now.
> > +		 * Just abort. The caller will repoll after a while.
> > +		 */
> >  		if (!(val & AC_ELDD_ELD_VALID)) {
> > -			if (!i) {
> > -				snd_printd(KERN_INFO
> > -					   "HDMI: invalid ELD data\n");
> > -				ret = -EINVAL;
> > -				goto error;
> > -			}
> >  			snd_printd(KERN_INFO
> >  				  "HDMI: invalid ELD data byte %d\n", i);
> > -			val = 0;
> > -		} else
> > -			val &= AC_ELDD_ELD_DATA;
> > +			ret = -EINVAL;
> > +			goto error;
> > +		}
> > +		val &= AC_ELDD_ELD_DATA;
> > +		/*
> > +		 * The first byte cannot be zero. This can happen on some DVI
> > +		 * connections. Some Intel chips may also need some 250ms delay
> > +		 * to return non-zero ELD data, even when the graphics driver
> > +		 * correctly writes ELD content before setting ELD_valid bit.
> > +		 */
> > +		if (!val && !i) {
> > +			snd_printdd(KERN_INFO "HDMI: 0 ELD data\n");
> > +			ret = -EINVAL;
> > +			goto error;
> > +		}
> 
> Shouldn't this zero-check be before the valid-bit check?
> Otherwise it'll never reach there.

It does reach there:

        [ 1191.016746] HDMI hot plug event: Codec=3 Pin=6 Presence_Detect=1 ELD_Valid=1
        [ 1191.019309] HDMI status: Codec=3 Pin=6 Presence_Detect=1 ELD_Valid=1
==>     [ 1191.021803] ALSA hda_eld.c:368 HDMI: 0 ELD data
        [ 1191.324661] HDMI status: Codec=3 Pin=6 Presence_Detect=1 ELD_Valid=1
        [ 1191.333236] HDMI: detected monitor SONY TV at connection type HDMI
        [ 1191.335020] HDMI: available speakers: FL/FR
        [ 1191.335996] HDMI: supports coding type LPCM: channels = 2, rates = 32000 44100 48000, bits = 16 20 24

The funny thing is, it's reporting (invalid) 0 ELD data that has
the AC_ELDD_ELD_VALID bit set.

Thanks,
Fengguang