From: Ralf Hildebrandt <Ralf.Hildebrandt@charite.de>
To: linux-kernel@vger.kernel.org
Subject: oops during modprobe (3.2.0-rc6+)
Date: Sat, 17 Dec 2011 22:36:45 +0100 [thread overview]
Message-ID: <20111217213645.GQ12099@charite.de> (raw)
Todya I pulled 3.2.0-rc6+ from git and built it for my machine. After
booting I found this in dmesg:
...
[ 6.322632] bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.1.11 (July 20, 2011)
[ 6.324608] hpwdt 0000:01:04.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 6.324680] hpwdt: New timer passed in is 30 seconds.
[ 6.324725] kernel tried to execute NX-protected page - exploit attempt? (uid: 0)
[ 6.324798] BUG: unable to handle kernel paging request at c00f0000
[ 6.324917] IP: [<c00f0000>] 0xc00effff
[ 6.325002] *pdpt = 00000000013b1001 *pde = 00000000013de067 *pte = 80000000000f0163
[ 6.325002] Oops: 0011 [#1] SMP
[ 6.325002] Modules linked in: hpwdt(+) bnx2(+) container psmouse thermal button processor
[ 6.325002]
[ 6.325002] Pid: 668, comm: modprobe Not tainted 3.2.0-rc6+ #16 HP ProLiant DL360 G5
[ 6.325002] EIP: 0060:[<c00f0000>] EFLAGS: 00010286 CPU: 3
[ 6.325002] EIP is at 0xc00f0000
[ 6.325905] EAX: 55524324 EBX: 00000000 ECX: 00000000 EDX: 00000000
[ 6.325905] ESI: 00000000 EDI: 00000000 EBP: f00cddd8 ESP: f00cdda8
[ 6.325905] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 6.325905] Process modprobe (pid: 668, ti=f00cc000 task=f0028000 task.ti=f00cc000)
[ 6.325905] Stack:
[ 6.325905] f8432020 00000060 c00e007b 00000286 c00ffee0 ffffffed f00cddd8 f00cddd8
[ 6.325905] c00f0000 00000001 00000000 c00f0000 f2cdbc00 f8432558 f8434100 c00f0000
[ 6.325905] f2c30564 ffffffff f8434030 000f0000 000f0000 f2d777e0 c0100000 c00f0000
[ 6.325905] Call Trace:
[ 6.325905] [<f8432020>] ? asminline_call+0x20/0x46 [hpwdt]
[ 6.325905] [<f8432558>] ? hpwdt_init_one+0x1a7/0x3c0 [hpwdt]
[ 6.325905] [<c115dc36>] ? pci_device_probe+0x47/0x68
[ 6.325905] [<c11aa0a7>] ? driver_probe_device+0x4a/0x13a
[ 6.325905] [<c115db04>] ? pci_match_device+0xf/0x8a
[ 6.325905] [<c11aa1f9>] ? __driver_attach+0x62/0x64
[ 6.325905] [<c11aa197>] ? driver_probe_device+0x13a/0x13a
[ 6.325905] [<c11a9543>] ? bus_for_each_dev+0x3e/0x62
[ 6.325905] [<c115dba2>] ? pci_dev_put+0xd/0xd
[ 6.325905] [<c11a9e69>] ? driver_attach+0x19/0x1e
[ 6.325905] [<c11aa197>] ? driver_probe_device+0x13a/0x13a
[ 6.325905] [<c11a9beb>] ? bus_add_driver+0x17d/0x24d
[ 6.325905] [<c115dba2>] ? pci_dev_put+0xd/0xd
[ 6.325905] [<c11aa3d9>] ? driver_register+0x57/0xec
[ 6.325905] [<c115dfef>] ? __pci_register_driver+0x31/0x92
[ 6.325905] [<c1001027>] ? do_one_initcall+0x27/0x150
[ 6.325905] [<c101c97e>] ? set_memory_nx+0x57/0x5b
[ 6.325905] [<f8410000>] ? 0xf840ffff
[ 6.325905] [<c1054416>] ? sys_init_module+0xdff/0x1a14
[ 6.325905] [<c126f717>] ? sysenter_do_call+0x12/0x26
[ 6.325905] Code: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
[ 6.329004] 90 80 fc d8 75 0d e9 da 06 00 00 69 04 00 00 ad 04 00 00 9c
[ 6.329004] EIP: [<c00f0000>] 0xc00f0000 SS:ESP 0068:f00cdda8
[ 6.329004] CR2: 00000000c00f0000
[ 6.329004] ---[ end trace 239ff8fe19067483 ]---
[ 6.443034] bnx2 0000:03:00.0: BAR 0: set to [mem 0xf8000000-0xf9ffffff 64bit] (PCI address [0xf8000000-0xf9ffffff])
[ 6.443123] bnx2 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 6.773259] bnx2 0000:03:00.0: eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 18, node addr 00:1e:0b:5f:f9:36
--
Ralf Hildebrandt
Geschäftsbereich IT | Abteilung Netzwerk
Charité - Universitätsmedizin Berlin
Campus Benjamin Franklin
Hindenburgdamm 30 | D-12203 Berlin
Tel. +49 30 450 570 155 | Fax: +49 30 450 570 962
ralf.hildebrandt@charite.de | http://www.charite.de
next reply other threads:[~2011-12-17 21:36 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-12-17 21:36 Ralf Hildebrandt [this message]
2011-12-20 2:35 ` oops during modprobe (3.2.0-rc6+) Josh Cartwright
2011-12-20 7:49 ` Wim Van Sebroeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20111217213645.GQ12099@charite.de \
--to=ralf.hildebrandt@charite.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.