From: Luka Perkov <uboot@lukaperkov.net>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v2] fix CFI flash driver for 8-bit bus support
Date: Mon, 13 Feb 2012 02:30:46 +0100 [thread overview]
Message-ID: <20120213013045.GA25085@w500.lan> (raw)
I'm not the author of version v1 of this patch but I need it to add
support for a new board. You can see patch v1 discussion here:
http://lists.denx.de/pipermail/u-boot/2011-April/089606.html
Changes from v1:
* fix whitespaces
* remove udelay(1); calls because they have been merged in a90b9575f3ff71de58672295504e9ebaa8f051b4
* remove reset call in flash_erase()
Originally it was signed of by Aaron.
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Tested-by: Luka Perkov <uboot@lukaperkov.net>
---
diff --git a/drivers/mtd/cfi_flash.c b/drivers/mtd/cfi_flash.c
index 722c3fc..55d866e 100644
--- a/drivers/mtd/cfi_flash.c
+++ b/drivers/mtd/cfi_flash.c
@@ -11,6 +11,9 @@
* Copyright (C) 2006
* Tolunay Orkun <listmember@orkun.us>
*
+ * Copyright (C) 2011 Cavium Networks, Inc.
+ * Aaron Williams <aaron.williams@caviumnetworks.com>
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
@@ -210,9 +213,11 @@ unsigned long flash_sector_size(flash_info_t *info, flash_sect_t sect)
static inline void *
flash_map (flash_info_t * info, flash_sect_t sect, uint offset)
{
- unsigned int byte_offset = offset * info->portwidth;
+ unsigned int byte_offset = offset * info->portwidth / info->chipwidth;
+ unsigned int addr = (info->start[sect] + byte_offset);
+ unsigned int mask = 0xffffffff << (info->portwidth - 1);
- return (void *)(info->start[sect] + byte_offset);
+ return (void *)(addr & mask);
}
static inline void flash_unmap(flash_info_t *info, flash_sect_t sect,
@@ -398,6 +403,8 @@ void flash_write_cmd (flash_info_t * info, flash_sect_t sect,
#endif
flash_write64(cword.ll, addr);
break;
+ default:
+ debug ("fwc: Unknown port width %d\n", info->portwidth);
}
/* Ensure all the instructions are fully finished */
@@ -585,7 +592,6 @@ static int flash_status_check (flash_info_t * info, flash_sect_t sector,
prompt, info->start[sector],
flash_read_long (info, sector, 0));
flash_write_cmd (info, sector, 0, info->cmd_reset);
- udelay(1);
return ERR_TIMOUT;
}
udelay (1); /* also triggers watchdog */
@@ -753,12 +759,8 @@ static void flash_add_byte (flash_info_t * info, cfiword_t * cword, uchar c)
static flash_sect_t find_sector (flash_info_t * info, ulong addr)
{
static flash_sect_t saved_sector = 0; /* previously found sector */
- static flash_info_t *saved_info = 0; /* previously used flash bank */
flash_sect_t sector = saved_sector;
- if ((info != saved_info) || (sector >= info->sector_count))
- sector = 0;
-
while ((info->start[sector] < addr)
&& (sector < info->sector_count - 1))
sector++;
@@ -770,7 +772,6 @@ static flash_sect_t find_sector (flash_info_t * info, ulong addr)
sector--;
saved_sector = sector;
- saved_info = info;
return sector;
}
@@ -834,12 +835,15 @@ static int flash_write_cfiword (flash_info_t * info, ulong dest,
switch (info->portwidth) {
case FLASH_CFI_8BIT:
+ debug("%s: 8-bit 0x%02x\n", __func__, cword.c);
flash_write8(cword.c, dstaddr);
break;
case FLASH_CFI_16BIT:
+ debug("%s: 16-bit 0x%04x\n", __func__, cword.w);
flash_write16(cword.w, dstaddr);
break;
case FLASH_CFI_32BIT:
+ debug("%s: 32-bit 0x%08lx\n", __func__, cword.l);
flash_write32(cword.l, dstaddr);
break;
case FLASH_CFI_64BIT:
@@ -1053,6 +1057,8 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
flash_sect_t sect;
int st;
+ debug("%s: erasing sectors %d to %d\n", __func__, s_first, s_last);
+
if (info->flash_id != FLASH_MAN_CFI) {
puts ("Can't erase unknown flash type - aborted\n");
return 1;
@@ -1130,6 +1136,8 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
rcode = 1;
else if (flash_verbose)
putc ('.');
+ } else {
+ debug("\nSector %d is protected.\n", sect);
}
}
@@ -1586,8 +1594,7 @@ static void cmdset_amd_read_jedec_ids(flash_info_t *info)
flash_unlock_seq(info, 0);
flash_write_cmd(info, 0, info->addr_unlock1, FLASH_CMD_READ_ID);
udelay(1000); /* some flash are slow to respond */
-
- manuId = flash_read_uchar (info, FLASH_OFFSET_MANUFACTURER_ID);
+ manuId = flash_read_uchar(info, FLASH_OFFSET_MANUFACTURER_ID);
/* JEDEC JEP106Z specifies ID codes up to bank 7 */
while (manuId == FLASH_CONTINUATION_CODE && bankId < 0x800) {
bankId += 0x100;
@@ -1741,7 +1748,7 @@ static void flash_read_cfi (flash_info_t *info, void *buf,
unsigned int i;
for (i = 0; i < len; i++)
- p[i] = flash_read_uchar(info, start + i);
+ p[i] = flash_read_uchar(info, start + (i * 2));
}
void __flash_cmd_reset(flash_info_t *info)
@@ -1762,21 +1769,38 @@ static int __flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry)
{
int cfi_offset;
- /* Issue FLASH reset command */
- flash_cmd_reset(info);
-
for (cfi_offset=0;
cfi_offset < sizeof(flash_offset_cfi) / sizeof(uint);
cfi_offset++) {
+ /* Issue FLASH reset command */
+ flash_cmd_reset(info);
flash_write_cmd (info, 0, flash_offset_cfi[cfi_offset],
FLASH_CMD_CFI);
if (flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP, 'Q')
- && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R')
- && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y')) {
+ && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 2, 'R')
+ && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 4, 'Y')) {
flash_read_cfi(info, qry, FLASH_OFFSET_CFI_RESP,
sizeof(struct cfi_qry));
+#ifdef CONFIG_SYS_FLASH_INTERFACE_WIDTH
+ info->interface = CONFIG_SYS_FLASH_INTERFACE_WIDTH;
+#else
info->interface = le16_to_cpu(qry->interface_desc);
-
+ /* Some flash chips can support multiple bus widths.
+ * In this case, override the interface width and
+ * limit it to the port width.
+ */
+ if ((info->interface == FLASH_CFI_X8X16) &&
+ (info->portwidth == FLASH_CFI_8BIT)) {
+ debug("Overriding 16-bit interface width to "
+ " 8-bit port width.\n");
+ info->interface = FLASH_CFI_X8;
+ } else if ((info->interface == FLASH_CFI_X16X32) &&
+ (info->portwidth == FLASH_CFI_16BIT)) {
+ debug("Overriding 16-bit interface width to "
+ " 16-bit port width.\n");
+ info->interface = FLASH_CFI_X16;
+ }
+#endif
info->cfi_offset = flash_offset_cfi[cfi_offset];
debug ("device interface is %d\n",
info->interface);
@@ -1787,8 +1811,8 @@ static int __flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry)
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
/* calculate command offsets as in the Linux driver */
- info->addr_unlock1 = 0x555;
- info->addr_unlock2 = 0x2aa;
+ info->addr_unlock1 = 0xaaa;
+ info->addr_unlock2 = 0x555;
/*
* modify the unlock address if we are
@@ -1822,8 +1846,11 @@ static int flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry)
for (info->chipwidth = FLASH_CFI_BY8;
info->chipwidth <= info->portwidth;
info->chipwidth <<= 1)
- if (__flash_detect_cfi(info, qry))
+ if (__flash_detect_cfi(info, qry)) {
+ debug("Found CFI flash, portwidth %d, chipwidth %d\n",
+ info->portwidth, info->chipwidth);
return 1;
+ }
}
debug ("not found\n");
return 0;
@@ -1842,7 +1869,7 @@ static void flash_fixup_amd(flash_info_t *info, struct cfi_qry *qry)
/* CFI < 1.1, try to guess from device id */
if ((info->device_id & 0x80) != 0)
cfi_reverse_geometry(qry);
- } else if (flash_read_uchar(info, info->ext_addr + 0xf) == 3) {
+ } else if (flash_read_uchar(info, info->ext_addr + 0x1e) == 3) {
/* CFI >= 1.1, deduct from top/bottom flag */
/* note: ext_addr is valid since cfi_version > 0 */
cfi_reverse_geometry(qry);
@@ -1919,14 +1946,15 @@ ulong flash_get_size (phys_addr_t base, int banknum)
if (flash_detect_cfi (info, &qry)) {
info->vendor = le16_to_cpu(qry.p_id);
- info->ext_addr = le16_to_cpu(qry.p_adr);
+ info->ext_addr = le16_to_cpu(qry.p_adr) * 2;
+ debug("extended address is 0x%x\n", info->ext_addr);
num_erase_regions = qry.num_erase_regions;
if (info->ext_addr) {
info->cfi_version = (ushort) flash_read_uchar (info,
- info->ext_addr + 3) << 8;
+ info->ext_addr + 6) << 8;
info->cfi_version |= (ushort) flash_read_uchar (info,
- info->ext_addr + 4);
+ info->ext_addr + 8);
}
#ifdef DEBUG
@@ -1974,13 +2002,9 @@ ulong flash_get_size (phys_addr_t base, int banknum)
debug ("device id is 0x%x\n", info->device_id);
debug ("device id2 is 0x%x\n", info->device_id2);
debug ("cfi version is 0x%04x\n", info->cfi_version);
-
+ debug ("port width: %d, chipwidth: %d, interface: %d\n",
+ info->portwidth, info->chipwidth, info->interface);
size_ratio = info->portwidth / info->chipwidth;
- /* if the chip is x8/x16 reduce the ratio by half */
- if ((info->interface == FLASH_CFI_X8X16)
- && (info->chipwidth == FLASH_CFI_BY8)) {
- size_ratio >>= 1;
- }
debug ("size_ratio %d port %d bits chip %d bits\n",
size_ratio, info->portwidth << CFI_FLASH_SHIFT_WIDTH,
info->chipwidth << CFI_FLASH_SHIFT_WIDTH);
@@ -2052,6 +2076,8 @@ ulong flash_get_size (phys_addr_t base, int banknum)
sect_cnt++;
}
}
+ debug ("port width: %d, chipwidth: %d, interface: %d\n",
+ info->portwidth, info->chipwidth, info->interface);
info->sector_count = sect_cnt;
info->buffer_size = 1 << le16_to_cpu(qry.max_buf_write_size);
diff --git a/include/mtd/cfi_flash.h b/include/mtd/cfi_flash.h
index 3245b44..edcf9be 100644
--- a/include/mtd/cfi_flash.h
+++ b/include/mtd/cfi_flash.h
@@ -71,29 +71,29 @@
#define FLASH_CONTINUATION_CODE 0x7F
#define FLASH_OFFSET_MANUFACTURER_ID 0x00
-#define FLASH_OFFSET_DEVICE_ID 0x01
-#define FLASH_OFFSET_DEVICE_ID2 0x0E
-#define FLASH_OFFSET_DEVICE_ID3 0x0F
-#define FLASH_OFFSET_CFI 0x55
+#define FLASH_OFFSET_DEVICE_ID 0x02
+#define FLASH_OFFSET_DEVICE_ID2 0x1C
+#define FLASH_OFFSET_DEVICE_ID3 0x1E
+#define FLASH_OFFSET_CFI 0xAA
#define FLASH_OFFSET_CFI_ALT 0x555
-#define FLASH_OFFSET_CFI_RESP 0x10
-#define FLASH_OFFSET_PRIMARY_VENDOR 0x13
+#define FLASH_OFFSET_CFI_RESP 0x20
+#define FLASH_OFFSET_PRIMARY_VENDOR 0x26
/* extended query table primary address */
-#define FLASH_OFFSET_EXT_QUERY_T_P_ADDR 0x15
+#define FLASH_OFFSET_EXT_QUERY_T_P_ADDR 0x2A
#define FLASH_OFFSET_WTOUT 0x1F
-#define FLASH_OFFSET_WBTOUT 0x20
-#define FLASH_OFFSET_ETOUT 0x21
-#define FLASH_OFFSET_CETOUT 0x22
-#define FLASH_OFFSET_WMAX_TOUT 0x23
-#define FLASH_OFFSET_WBMAX_TOUT 0x24
-#define FLASH_OFFSET_EMAX_TOUT 0x25
-#define FLASH_OFFSET_CEMAX_TOUT 0x26
-#define FLASH_OFFSET_SIZE 0x27
-#define FLASH_OFFSET_INTERFACE 0x28
-#define FLASH_OFFSET_BUFFER_SIZE 0x2A
-#define FLASH_OFFSET_NUM_ERASE_REGIONS 0x2C
-#define FLASH_OFFSET_ERASE_REGIONS 0x2D
-#define FLASH_OFFSET_PROTECT 0x02
+#define FLASH_OFFSET_WBTOUT 0x40
+#define FLASH_OFFSET_ETOUT 0x4A
+#define FLASH_OFFSET_CETOUT 0x44
+#define FLASH_OFFSET_WMAX_TOUT 0x46
+#define FLASH_OFFSET_WBMAX_TOUT 0x48
+#define FLASH_OFFSET_EMAX_TOUT 0x4A
+#define FLASH_OFFSET_CEMAX_TOUT 0x4C
+#define FLASH_OFFSET_SIZE 0x4E
+#define FLASH_OFFSET_INTERFACE 0x50
+#define FLASH_OFFSET_BUFFER_SIZE 0x54
+#define FLASH_OFFSET_NUM_ERASE_REGIONS 0x58
+#define FLASH_OFFSET_ERASE_REGIONS 0x5A
+#define FLASH_OFFSET_PROTECT 0x04
#define FLASH_OFFSET_USER_PROTECTION 0x85
#define FLASH_OFFSET_INTEL_PROTECTION 0x81
next reply other threads:[~2012-02-13 1:30 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-02-13 1:30 Luka Perkov [this message]
2012-02-13 10:32 ` [U-Boot] [PATCH v2] fix CFI flash driver for 8-bit bus support Wolfgang Denk
2012-02-14 0:51 ` Luka Perkov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120213013045.GA25085@w500.lan \
--to=uboot@lukaperkov.net \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.