From: Tony Lindgren <tony@atomide.com>
To: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Subject: Re: [PATCH 5/8] ARM: OMAP1: Move most of plat/io.h into local iomap.h
Date: Thu, 23 Feb 2012 15:44:47 -0800 [thread overview]
Message-ID: <20120223234447.GH18185@atomide.com> (raw)
In-Reply-To: <20120221234044.18709.32045.stgit@kaulin.local>
* Tony Lindgren <tony@atomide.com> [120221 15:09]:
> There's no need to have these in plat/io.h.
>
> While at it, clean up the includes to group them
> like they typically are grouped.
...
> diff --git a/arch/arm/mach-omap1/iomap.h b/arch/arm/mach-omap1/iomap.h
> new file mode 100644
> index 0000000..c2cdf71
> --- /dev/null
> +++ b/arch/arm/mach-omap1/iomap.h
> @@ -0,0 +1,18 @@
> +#ifdef __ASSEMBLER__
> +#define IOMEM(x) (x)
> +#else
> +#define IOMEM(x) ((void __force __iomem *)(x))
> +#endif
> +
> +#define OMAP1_IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */
> +#define OMAP1_IO_ADDRESS(pa) IOMEM((pa) - OMAP1_IO_OFFSET)
> +
> +/*
> + * ----------------------------------------------------------------------------
> + * Omap1 specific IO mapping
> + * ----------------------------------------------------------------------------
> + */
> +
> +#define OMAP1_IO_PHYS 0xFFFB0000
> +#define OMAP1_IO_SIZE 0x40000
> +#define OMAP1_IO_VIRT (OMAP1_IO_PHYS - OMAP1_IO_OFFSET)
Looks like the iomap.h is missing license, so updated patch below.
Regards,
Tony
From: Tony Lindgren <tony@atomide.com>
Date: Wed, 22 Feb 2012 14:52:39 -0800
Subject: [PATCH] ARM: OMAP1: Move most of plat/io.h into local iomap.h
There's no need to have these in plat/io.h.
While at it, clean up the includes to group them
like they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/ams-delta-fiq-handler.S b/arch/arm/mach-omap1/ams-delta-fiq-handler.S
index c1c5fb6..399c4c4 100644
--- a/arch/arm/mach-omap1/ams-delta-fiq-handler.S
+++ b/arch/arm/mach-omap1/ams-delta-fiq-handler.S
@@ -15,11 +15,12 @@
#include <linux/linkage.h>
-#include <plat/io.h>
#include <plat/board-ams-delta.h>
#include <mach/ams-delta-fiq.h>
+#include "iomap.h"
+
/*
* GPIO related definitions, copied from arch/arm/plat-omap/gpio.c.
* Unfortunately, those were not placed in a separate header file.
diff --git a/arch/arm/mach-omap1/ams-delta-fiq.c b/arch/arm/mach-omap1/ams-delta-fiq.c
index 152b32c..fcce7ff 100644
--- a/arch/arm/mach-omap1/ams-delta-fiq.c
+++ b/arch/arm/mach-omap1/ams-delta-fiq.c
@@ -22,6 +22,7 @@
#include <plat/board-ams-delta.h>
#include <asm/fiq.h>
+
#include <mach/ams-delta-fiq.h>
static struct fiq_handler fh = {
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 88909cc..ac65d7d 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -20,25 +20,27 @@
#include <linux/platform_device.h>
#include <linux/serial_8250.h>
#include <linux/export.h>
+#include <linux/io.h>
#include <media/soc_camera.h>
#include <asm/serial.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <plat/io.h>
#include <plat/board-ams-delta.h>
#include <plat/keypad.h>
#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
-#include "common.h"
-#include <mach/camera.h>
+#include <mach/hardware.h>
#include <mach/ams-delta-fiq.h>
+#include <mach/camera.h>
+
+#include "iomap.h"
+#include "common.h"
static u8 ams_delta_latch1_reg;
static u16 ams_delta_latch2_reg;
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 0b9464b..079292c 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -22,7 +22,6 @@
#include <linux/input.h>
#include <linux/smc91x.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -32,9 +31,13 @@
#include <plat/flash.h>
#include <plat/fpga.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/board.h>
+#include <mach/hardware.h>
+
+#include "iomap.h"
+#include "common.h"
+
/* fsample is pretty close to p2-sample */
#define fsample_cpld_read(reg) __raw_readb(reg)
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index 00ad6b2..03e0050 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -31,8 +31,6 @@
#include <linux/i2c/tps65010.h>
#include <linux/smc91x.h>
-#include <mach/hardware.h>
-
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -43,9 +41,11 @@
#include <plat/irda.h>
#include <plat/usb.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/flash.h>
+#include <mach/hardware.h>
+
+#include "common.h"
#include "board-h2.h"
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 4a7f251..f304fe2 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -33,21 +33,21 @@
#include <asm/setup.h>
#include <asm/page.h>
-#include <mach/hardware.h>
-
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/irqs.h>
#include <plat/mux.h>
#include <plat/tc.h>
#include <plat/usb.h>
#include <plat/keypad.h>
#include <plat/dma.h>
-#include "common.h"
#include <plat/flash.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+
+#include "common.h"
#include "board-h3.h"
/* In OMAP1710 H3 the Ethernet is directly connected to CS1 */
diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c
index 731cc3d..fa52d14 100644
--- a/arch/arm/mach-omap1/board-htcherald.c
+++ b/arch/arm/mach-omap1/board-htcherald.c
@@ -27,7 +27,7 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/input.h>
-#include <linux/io.h>
+#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/i2c.h>
@@ -41,7 +41,6 @@
#include <asm/mach/arch.h>
#include <plat/omap7xx.h>
-#include "common.h"
#include <plat/board.h>
#include <plat/keypad.h>
#include <plat/usb.h>
@@ -49,7 +48,7 @@
#include <mach/irqs.h>
-#include <linux/delay.h>
+#include "common.h"
/* LCD register definition */
#define OMAP_LCDC_CONTROL (0xfffec000 + 0x00)
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index 309369e..289a6b8 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -26,7 +26,6 @@
#include <linux/input.h>
#include <linux/smc91x.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -37,9 +36,13 @@
#include <plat/tc.h>
#include <plat/usb.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/mmc.h>
+#include <mach/hardware.h>
+
+#include "iomap.h"
+#include "common.h"
+
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
#define INNOVATOR1610_ETHR_START 0x04000300
diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index f9efc03..abdbdb0 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -21,7 +21,6 @@
#include <linux/workqueue.h>
#include <linux/delay.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -30,12 +29,15 @@
#include <plat/usb.h>
#include <plat/board.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/hwa742.h>
#include <plat/lcd_mipid.h>
#include <plat/mmc.h>
#include <plat/clock.h>
+#include <mach/hardware.h>
+
+#include "common.h"
+
#define ADS7846_PENDOWN_GPIO 15
static const unsigned int nokia770_keymap[] = {
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index 675de06..e2d7ae4 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -34,15 +34,11 @@
#include <linux/i2c.h>
#include <linux/leds.h>
#include <linux/smc91x.h>
-
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
-
#include <linux/i2c/tps65010.h>
-#include <mach/hardware.h>
-
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -51,6 +47,9 @@
#include <plat/usb.h>
#include <plat/mux.h>
#include <plat/tc.h>
+
+#include <mach/hardware.h>
+
#include "common.h"
/* At OMAP5912 OSK the Ethernet is directly connected to CS1 */
diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index 81fa27f..04efa7e 100644
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -28,7 +28,6 @@
#include <linux/interrupt.h>
#include <linux/apm-emulation.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -41,6 +40,9 @@
#include <plat/board.h>
#include <plat/irda.h>
#include <plat/keypad.h>
+
+#include <mach/hardware.h>
+
#include "common.h"
#define PALMTE_USBDETECT_GPIO 0
diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c
index 81cb821..acd1f36 100644
--- a/arch/arm/mach-omap1/board-palmtt.c
+++ b/arch/arm/mach-omap1/board-palmtt.c
@@ -24,8 +24,9 @@
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -39,10 +40,10 @@
#include <plat/board.h>
#include <plat/irda.h>
#include <plat/keypad.h>
-#include "common.h"
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
+#include <mach/hardware.h>
+
+#include "common.h"
#define PALMTT_USBDETECT_GPIO 0
#define PALMTT_CABLE_GPIO 1
diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c
index e881945..c1cd0f2 100644
--- a/arch/arm/mach-omap1/board-palmz71.c
+++ b/arch/arm/mach-omap1/board-palmz71.c
@@ -27,8 +27,9 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -41,10 +42,10 @@
#include <plat/board.h>
#include <plat/irda.h>
#include <plat/keypad.h>
-#include "common.h"
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
+#include <mach/hardware.h>
+
+#include "common.h"
#define PALMZ71_USBDETECT_GPIO 0
#define PALMZ71_PENIRQ_GPIO 6
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index c000bed..83f5b76 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -22,7 +22,6 @@
#include <linux/input.h>
#include <linux/smc91x.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -32,9 +31,13 @@
#include <plat/fpga.h>
#include <plat/flash.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/board.h>
+#include <mach/hardware.h>
+
+#include "iomap.h"
+#include "common.h"
+
static const unsigned int p2_keymap[] = {
KEY(0, 0, KEY_UP),
KEY(1, 0, KEY_RIGHT),
diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c
index 7bcd82a..fed4435 100644
--- a/arch/arm/mach-omap1/board-sx1.c
+++ b/arch/arm/mach-omap1/board-sx1.c
@@ -28,7 +28,6 @@
#include <linux/errno.h>
#include <linux/export.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -40,10 +39,13 @@
#include <plat/usb.h>
#include <plat/tc.h>
#include <plat/board.h>
-#include "common.h"
#include <plat/keypad.h>
#include <plat/board-sx1.h>
+#include <mach/hardware.h>
+
+#include "common.h"
+
/* Write to I2C device */
int sx1_i2c_write_byte(u8 devaddr, u8 regoffset, u8 value)
{
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index f83a502..659d0f7 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -27,18 +27,20 @@
#include <linux/smc91x.h>
#include <linux/export.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <plat/board-voiceblue.h>
-#include "common.h"
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/tc.h>
#include <plat/usb.h>
+#include <mach/hardware.h>
+
+#include "common.h"
+
static struct plat_serial8250_port voiceblue_ports[] = {
{
.mapbase = (unsigned long)(OMAP_CS1_PHYS + 0x40000),
diff --git a/arch/arm/mach-omap1/clock.c b/arch/arm/mach-omap1/clock.c
index 0c50df0..0e8c176 100644
--- a/arch/arm/mach-omap1/clock.c
+++ b/arch/arm/mach-omap1/clock.c
@@ -16,7 +16,6 @@
#include <linux/errno.h>
#include <linux/err.h>
#include <linux/clk.h>
-#include <linux/io.h>
#include <linux/clkdev.h>
#include <asm/mach-types.h>
@@ -27,6 +26,7 @@
#include <plat/sram.h>
#include <plat/clkdev_omap.h>
+#include "iomap.h"
#include "clock.h"
#include "opp.h"
diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c
index 94699a8..10b7451 100644
--- a/arch/arm/mach-omap1/clock_data.c
+++ b/arch/arm/mach-omap1/clock_data.c
@@ -18,7 +18,6 @@
#include <linux/clk.h>
#include <linux/cpufreq.h>
#include <linux/delay.h>
-#include <linux/io.h>
#include <asm/mach-types.h> /* for machine_is_* */
@@ -28,6 +27,7 @@
#include <plat/sram.h> /* for omap_sram_reprogram_clock() */
#include <plat/usb.h> /* for OTG_BASE */
+#include "iomap.h"
#include "clock.h"
/* Some ARM_IDLECT1 bit shifts - used in struct arm_idlect1_clk */
diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c
index 1d76a63..d06c714 100644
--- a/arch/arm/mach-omap1/devices.c
+++ b/arch/arm/mach-omap1/devices.c
@@ -15,14 +15,10 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/io.h>
#include <linux/spi/spi.h>
-#include <mach/camera.h>
-#include <mach/hardware.h>
#include <asm/mach/map.h>
-#include "common.h"
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/mux.h>
@@ -30,6 +26,10 @@
#include <plat/omap7xx.h>
#include <plat/mcbsp.h>
+#include <mach/camera.h>
+#include <mach/hardware.h>
+
+#include "common.h"
#include "clock.h"
/*-------------------------------------------------------------------------*/
diff --git a/arch/arm/mach-omap1/dma.c b/arch/arm/mach-omap1/dma.c
index f5a5220..3ef7d52 100644
--- a/arch/arm/mach-omap1/dma.c
+++ b/arch/arm/mach-omap1/dma.c
@@ -19,11 +19,11 @@
*/
#include <linux/err.h>
-#include <linux/io.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/io.h>
#include <plat/dma.h>
#include <plat/tc.h>
diff --git a/arch/arm/mach-omap1/flash.c b/arch/arm/mach-omap1/flash.c
index 1749cb3..98d29a0 100644
--- a/arch/arm/mach-omap1/flash.c
+++ b/arch/arm/mach-omap1/flash.c
@@ -6,10 +6,10 @@
* published by the Free Software Foundation.
*/
+#include <linux/io.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/map.h>
-#include <plat/io.h>
#include <plat/tc.h>
#include <plat/flash.h>
diff --git a/arch/arm/mach-omap1/fpga.c b/arch/arm/mach-omap1/fpga.c
index 0a17a1a..76c67b3 100644
--- a/arch/arm/mach-omap1/fpga.c
+++ b/arch/arm/mach-omap1/fpga.c
@@ -24,12 +24,15 @@
#include <linux/errno.h>
#include <linux/io.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <plat/fpga.h>
+#include <mach/hardware.h>
+
+#include "iomap.h"
+
static void fpga_mask_irq(struct irq_data *d)
{
unsigned int irq = d->irq - OMAP_FPGA_IRQ_BASE;
diff --git a/arch/arm/mach-omap1/id.c b/arch/arm/mach-omap1/id.c
index a0e3560..7483db2 100644
--- a/arch/arm/mach-omap1/id.c
+++ b/arch/arm/mach-omap1/id.c
@@ -15,6 +15,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
+
#include <plat/cpu.h>
#define OMAP_DIE_ID_0 0xfffe1800
diff --git a/arch/arm/mach-omap1/include/mach/entry-macro.S b/arch/arm/mach-omap1/include/mach/entry-macro.S
index bfb4fb1..68d2679 100644
--- a/arch/arm/mach-omap1/include/mach/entry-macro.S
+++ b/arch/arm/mach-omap1/include/mach/entry-macro.S
@@ -9,10 +9,12 @@
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
+
#include <mach/hardware.h>
#include <mach/io.h>
#include <mach/irqs.h>
-#include <asm/hardware/gic.h>
+
+#include "../../iomap.h"
.macro disable_fiq
.endm
diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c
index 8e55b6f..56fb444 100644
--- a/arch/arm/mach-omap1/io.c
+++ b/arch/arm/mach-omap1/io.c
@@ -15,9 +15,12 @@
#include <asm/tlb.h>
#include <asm/mach/map.h>
+
#include <plat/mux.h>
#include <plat/tc.h>
+#include "iomap.h"
+#include "common.h"
#include "clock.h"
extern void omap_check_revision(void);
diff --git a/arch/arm/mach-omap1/iomap.h b/arch/arm/mach-omap1/iomap.h
new file mode 100644
index 0000000..d681757
--- /dev/null
+++ b/arch/arm/mach-omap1/iomap.h
@@ -0,0 +1,42 @@
+/*
+ * IO mappings for OMAP1
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifdef __ASSEMBLER__
+#define IOMEM(x) (x)
+#else
+#define IOMEM(x) ((void __force __iomem *)(x))
+#endif
+
+#define OMAP1_IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */
+#define OMAP1_IO_ADDRESS(pa) IOMEM((pa) - OMAP1_IO_OFFSET)
+
+/*
+ * ----------------------------------------------------------------------------
+ * Omap1 specific IO mapping
+ * ----------------------------------------------------------------------------
+ */
+
+#define OMAP1_IO_PHYS 0xFFFB0000
+#define OMAP1_IO_SIZE 0x40000
+#define OMAP1_IO_VIRT (OMAP1_IO_PHYS - OMAP1_IO_OFFSET)
diff --git a/arch/arm/mach-omap1/irq.c b/arch/arm/mach-omap1/irq.c
index e5b104b..4448114 100644
--- a/arch/arm/mach-omap1/irq.c
+++ b/arch/arm/mach-omap1/irq.c
@@ -42,11 +42,13 @@
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
+
#include <plat/cpu.h>
+#include <mach/hardware.h>
+
#define IRQ_BANK(irq) ((irq) >> 5)
#define IRQ_BIT(irq) ((irq) & 0x1f)
diff --git a/arch/arm/mach-omap1/lcd_dma.c b/arch/arm/mach-omap1/lcd_dma.c
index 4538093..123a0df 100644
--- a/arch/arm/mach-omap1/lcd_dma.c
+++ b/arch/arm/mach-omap1/lcd_dma.c
@@ -27,9 +27,10 @@
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <plat/dma.h>
+
#include <mach/hardware.h>
#include <mach/lcdc.h>
-#include <plat/dma.h>
int omap_lcd_dma_running(void)
{
diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c
index 91f9abb..3082d60 100644
--- a/arch/arm/mach-omap1/mcbsp.c
+++ b/arch/arm/mach-omap1/mcbsp.c
@@ -19,12 +19,15 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
-#include <mach/irqs.h>
#include <plat/dma.h>
#include <plat/mux.h>
#include <plat/cpu.h>
#include <plat/mcbsp.h>
+#include <mach/irqs.h>
+
+#include "iomap.h"
+
#define DPS_RSTCT2_PER_EN (1 << 0)
#define DSP_RSTCT2_WD_PER_EN (1 << 1)
diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c
index 89ea20c..c06bb40 100644
--- a/arch/arm/mach-omap1/pm.c
+++ b/arch/arm/mach-omap1/pm.c
@@ -42,14 +42,13 @@
#include <linux/sysfs.h>
#include <linux/module.h>
#include <linux/io.h>
+#include <linux/atomic.h>
#include <asm/irq.h>
-#include <linux/atomic.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
#include <plat/cpu.h>
-#include <mach/irqs.h>
#include <plat/clock.h>
#include <plat/sram.h>
#include <plat/tc.h>
@@ -57,6 +56,9 @@
#include <plat/dma.h>
#include <plat/dmtimer.h>
+#include <mach/irqs.h>
+
+#include "iomap.h"
#include "pm.h"
static unsigned int arm_sleep_save[ARM_SLEEP_SAVE_SIZE];
diff --git a/arch/arm/mach-omap1/reset.c b/arch/arm/mach-omap1/reset.c
index 91d199b..f255b15 100644
--- a/arch/arm/mach-omap1/reset.c
+++ b/arch/arm/mach-omap1/reset.c
@@ -4,9 +4,10 @@
#include <linux/kernel.h>
#include <linux/io.h>
-#include <mach/hardware.h>
#include <plat/prcm.h>
+#include <mach/hardware.h>
+
void omap1_restart(char mode, const char *cmd)
{
/*
diff --git a/arch/arm/mach-omap1/sleep.S b/arch/arm/mach-omap1/sleep.S
index c875bdc..0779db1 100644
--- a/arch/arm/mach-omap1/sleep.S
+++ b/arch/arm/mach-omap1/sleep.S
@@ -33,8 +33,12 @@
*/
#include <linux/linkage.h>
+
#include <asm/assembler.h>
+
#include <mach/io.h>
+
+#include "iomap.h"
#include "pm.h"
.text
diff --git a/arch/arm/mach-omap1/sram.S b/arch/arm/mach-omap1/sram.S
index 692587d..2ce0b9a 100644
--- a/arch/arm/mach-omap1/sram.S
+++ b/arch/arm/mach-omap1/sram.S
@@ -9,10 +9,14 @@
*/
#include <linux/linkage.h>
+
#include <asm/assembler.h>
+
#include <mach/io.h>
#include <mach/hardware.h>
+#include "iomap.h"
+
.text
/*
diff --git a/arch/arm/mach-omap1/time.c b/arch/arm/mach-omap1/time.c
index b8faffa..2fae6a2 100644
--- a/arch/arm/mach-omap1/time.c
+++ b/arch/arm/mach-omap1/time.c
@@ -45,14 +45,15 @@
#include <linux/io.h>
#include <asm/system.h>
-#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/irq.h>
#include <asm/sched_clock.h>
+#include <mach/hardware.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
+#include "iomap.h"
#include "common.h"
#ifdef CONFIG_OMAP_MPU_TIMER
diff --git a/arch/arm/mach-omap1/timer32k.c b/arch/arm/mach-omap1/timer32k.c
index 9a54ef4..a2e6d07 100644
--- a/arch/arm/mach-omap1/timer32k.c
+++ b/arch/arm/mach-omap1/timer32k.c
@@ -47,14 +47,17 @@
#include <linux/io.h>
#include <asm/system.h>
-#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
-#include "common.h"
+
#include <plat/dmtimer.h>
+#include <mach/hardware.h>
+
+#include "common.h"
+
/*
* ---------------------------------------------------------------------------
* 32KHz OS timer
diff --git a/arch/arm/plat-omap/include/plat/io.h b/arch/arm/plat-omap/include/plat/io.h
index 28cd796..e5e8e08 100644
--- a/arch/arm/plat-omap/include/plat/io.h
+++ b/arch/arm/plat-omap/include/plat/io.h
@@ -60,9 +60,6 @@
#define IOMEM(x) ((void __force __iomem *)(x))
#endif
-#define OMAP1_IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */
-#define OMAP1_IO_ADDRESS(pa) IOMEM((pa) - OMAP1_IO_OFFSET)
-
#define OMAP2_L3_IO_OFFSET 0x90000000
#define OMAP2_L3_IO_ADDRESS(pa) IOMEM((pa) + OMAP2_L3_IO_OFFSET) /* L3 */
@@ -87,16 +84,6 @@
/*
* ----------------------------------------------------------------------------
- * Omap1 specific IO mapping
- * ----------------------------------------------------------------------------
- */
-
-#define OMAP1_IO_PHYS 0xFFFB0000
-#define OMAP1_IO_SIZE 0x40000
-#define OMAP1_IO_VIRT (OMAP1_IO_PHYS - OMAP1_IO_OFFSET)
-
-/*
- * ----------------------------------------------------------------------------
* Omap2 specific IO mapping
* ----------------------------------------------------------------------------
*/
WARNING: multiple messages have this Message-ID (diff)
From: tony@atomide.com (Tony Lindgren)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 5/8] ARM: OMAP1: Move most of plat/io.h into local iomap.h
Date: Thu, 23 Feb 2012 15:44:47 -0800 [thread overview]
Message-ID: <20120223234447.GH18185@atomide.com> (raw)
In-Reply-To: <20120221234044.18709.32045.stgit@kaulin.local>
* Tony Lindgren <tony@atomide.com> [120221 15:09]:
> There's no need to have these in plat/io.h.
>
> While at it, clean up the includes to group them
> like they typically are grouped.
...
> diff --git a/arch/arm/mach-omap1/iomap.h b/arch/arm/mach-omap1/iomap.h
> new file mode 100644
> index 0000000..c2cdf71
> --- /dev/null
> +++ b/arch/arm/mach-omap1/iomap.h
> @@ -0,0 +1,18 @@
> +#ifdef __ASSEMBLER__
> +#define IOMEM(x) (x)
> +#else
> +#define IOMEM(x) ((void __force __iomem *)(x))
> +#endif
> +
> +#define OMAP1_IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */
> +#define OMAP1_IO_ADDRESS(pa) IOMEM((pa) - OMAP1_IO_OFFSET)
> +
> +/*
> + * ----------------------------------------------------------------------------
> + * Omap1 specific IO mapping
> + * ----------------------------------------------------------------------------
> + */
> +
> +#define OMAP1_IO_PHYS 0xFFFB0000
> +#define OMAP1_IO_SIZE 0x40000
> +#define OMAP1_IO_VIRT (OMAP1_IO_PHYS - OMAP1_IO_OFFSET)
Looks like the iomap.h is missing license, so updated patch below.
Regards,
Tony
From: Tony Lindgren <tony@atomide.com>
Date: Wed, 22 Feb 2012 14:52:39 -0800
Subject: [PATCH] ARM: OMAP1: Move most of plat/io.h into local iomap.h
There's no need to have these in plat/io.h.
While at it, clean up the includes to group them
like they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/ams-delta-fiq-handler.S b/arch/arm/mach-omap1/ams-delta-fiq-handler.S
index c1c5fb6..399c4c4 100644
--- a/arch/arm/mach-omap1/ams-delta-fiq-handler.S
+++ b/arch/arm/mach-omap1/ams-delta-fiq-handler.S
@@ -15,11 +15,12 @@
#include <linux/linkage.h>
-#include <plat/io.h>
#include <plat/board-ams-delta.h>
#include <mach/ams-delta-fiq.h>
+#include "iomap.h"
+
/*
* GPIO related definitions, copied from arch/arm/plat-omap/gpio.c.
* Unfortunately, those were not placed in a separate header file.
diff --git a/arch/arm/mach-omap1/ams-delta-fiq.c b/arch/arm/mach-omap1/ams-delta-fiq.c
index 152b32c..fcce7ff 100644
--- a/arch/arm/mach-omap1/ams-delta-fiq.c
+++ b/arch/arm/mach-omap1/ams-delta-fiq.c
@@ -22,6 +22,7 @@
#include <plat/board-ams-delta.h>
#include <asm/fiq.h>
+
#include <mach/ams-delta-fiq.h>
static struct fiq_handler fh = {
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 88909cc..ac65d7d 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -20,25 +20,27 @@
#include <linux/platform_device.h>
#include <linux/serial_8250.h>
#include <linux/export.h>
+#include <linux/io.h>
#include <media/soc_camera.h>
#include <asm/serial.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <plat/io.h>
#include <plat/board-ams-delta.h>
#include <plat/keypad.h>
#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
-#include "common.h"
-#include <mach/camera.h>
+#include <mach/hardware.h>
#include <mach/ams-delta-fiq.h>
+#include <mach/camera.h>
+
+#include "iomap.h"
+#include "common.h"
static u8 ams_delta_latch1_reg;
static u16 ams_delta_latch2_reg;
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index 0b9464b..079292c 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -22,7 +22,6 @@
#include <linux/input.h>
#include <linux/smc91x.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -32,9 +31,13 @@
#include <plat/flash.h>
#include <plat/fpga.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/board.h>
+#include <mach/hardware.h>
+
+#include "iomap.h"
+#include "common.h"
+
/* fsample is pretty close to p2-sample */
#define fsample_cpld_read(reg) __raw_readb(reg)
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index 00ad6b2..03e0050 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -31,8 +31,6 @@
#include <linux/i2c/tps65010.h>
#include <linux/smc91x.h>
-#include <mach/hardware.h>
-
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -43,9 +41,11 @@
#include <plat/irda.h>
#include <plat/usb.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/flash.h>
+#include <mach/hardware.h>
+
+#include "common.h"
#include "board-h2.h"
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 4a7f251..f304fe2 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -33,21 +33,21 @@
#include <asm/setup.h>
#include <asm/page.h>
-#include <mach/hardware.h>
-
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
-#include <mach/irqs.h>
#include <plat/mux.h>
#include <plat/tc.h>
#include <plat/usb.h>
#include <plat/keypad.h>
#include <plat/dma.h>
-#include "common.h"
#include <plat/flash.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+
+#include "common.h"
#include "board-h3.h"
/* In OMAP1710 H3 the Ethernet is directly connected to CS1 */
diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c
index 731cc3d..fa52d14 100644
--- a/arch/arm/mach-omap1/board-htcherald.c
+++ b/arch/arm/mach-omap1/board-htcherald.c
@@ -27,7 +27,7 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/input.h>
-#include <linux/io.h>
+#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/i2c.h>
@@ -41,7 +41,6 @@
#include <asm/mach/arch.h>
#include <plat/omap7xx.h>
-#include "common.h"
#include <plat/board.h>
#include <plat/keypad.h>
#include <plat/usb.h>
@@ -49,7 +48,7 @@
#include <mach/irqs.h>
-#include <linux/delay.h>
+#include "common.h"
/* LCD register definition */
#define OMAP_LCDC_CONTROL (0xfffec000 + 0x00)
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index 309369e..289a6b8 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -26,7 +26,6 @@
#include <linux/input.h>
#include <linux/smc91x.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -37,9 +36,13 @@
#include <plat/tc.h>
#include <plat/usb.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/mmc.h>
+#include <mach/hardware.h>
+
+#include "iomap.h"
+#include "common.h"
+
/* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
#define INNOVATOR1610_ETHR_START 0x04000300
diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index f9efc03..abdbdb0 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -21,7 +21,6 @@
#include <linux/workqueue.h>
#include <linux/delay.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -30,12 +29,15 @@
#include <plat/usb.h>
#include <plat/board.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/hwa742.h>
#include <plat/lcd_mipid.h>
#include <plat/mmc.h>
#include <plat/clock.h>
+#include <mach/hardware.h>
+
+#include "common.h"
+
#define ADS7846_PENDOWN_GPIO 15
static const unsigned int nokia770_keymap[] = {
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index 675de06..e2d7ae4 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -34,15 +34,11 @@
#include <linux/i2c.h>
#include <linux/leds.h>
#include <linux/smc91x.h>
-
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
-
#include <linux/i2c/tps65010.h>
-#include <mach/hardware.h>
-
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -51,6 +47,9 @@
#include <plat/usb.h>
#include <plat/mux.h>
#include <plat/tc.h>
+
+#include <mach/hardware.h>
+
#include "common.h"
/* At OMAP5912 OSK the Ethernet is directly connected to CS1 */
diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index 81fa27f..04efa7e 100644
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -28,7 +28,6 @@
#include <linux/interrupt.h>
#include <linux/apm-emulation.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -41,6 +40,9 @@
#include <plat/board.h>
#include <plat/irda.h>
#include <plat/keypad.h>
+
+#include <mach/hardware.h>
+
#include "common.h"
#define PALMTE_USBDETECT_GPIO 0
diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c
index 81cb821..acd1f36 100644
--- a/arch/arm/mach-omap1/board-palmtt.c
+++ b/arch/arm/mach-omap1/board-palmtt.c
@@ -24,8 +24,9 @@
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/leds.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -39,10 +40,10 @@
#include <plat/board.h>
#include <plat/irda.h>
#include <plat/keypad.h>
-#include "common.h"
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
+#include <mach/hardware.h>
+
+#include "common.h"
#define PALMTT_USBDETECT_GPIO 0
#define PALMTT_CABLE_GPIO 1
diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c
index e881945..c1cd0f2 100644
--- a/arch/arm/mach-omap1/board-palmz71.c
+++ b/arch/arm/mach-omap1/board-palmz71.c
@@ -27,8 +27,9 @@
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -41,10 +42,10 @@
#include <plat/board.h>
#include <plat/irda.h>
#include <plat/keypad.h>
-#include "common.h"
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
+#include <mach/hardware.h>
+
+#include "common.h"
#define PALMZ71_USBDETECT_GPIO 0
#define PALMZ71_PENIRQ_GPIO 6
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index c000bed..83f5b76 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -22,7 +22,6 @@
#include <linux/input.h>
#include <linux/smc91x.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -32,9 +31,13 @@
#include <plat/fpga.h>
#include <plat/flash.h>
#include <plat/keypad.h>
-#include "common.h"
#include <plat/board.h>
+#include <mach/hardware.h>
+
+#include "iomap.h"
+#include "common.h"
+
static const unsigned int p2_keymap[] = {
KEY(0, 0, KEY_UP),
KEY(1, 0, KEY_RIGHT),
diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c
index 7bcd82a..fed4435 100644
--- a/arch/arm/mach-omap1/board-sx1.c
+++ b/arch/arm/mach-omap1/board-sx1.c
@@ -28,7 +28,6 @@
#include <linux/errno.h>
#include <linux/export.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
@@ -40,10 +39,13 @@
#include <plat/usb.h>
#include <plat/tc.h>
#include <plat/board.h>
-#include "common.h"
#include <plat/keypad.h>
#include <plat/board-sx1.h>
+#include <mach/hardware.h>
+
+#include "common.h"
+
/* Write to I2C device */
int sx1_i2c_write_byte(u8 devaddr, u8 regoffset, u8 value)
{
diff --git a/arch/arm/mach-omap1/board-voiceblue.c b/arch/arm/mach-omap1/board-voiceblue.c
index f83a502..659d0f7 100644
--- a/arch/arm/mach-omap1/board-voiceblue.c
+++ b/arch/arm/mach-omap1/board-voiceblue.c
@@ -27,18 +27,20 @@
#include <linux/smc91x.h>
#include <linux/export.h>
-#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <plat/board-voiceblue.h>
-#include "common.h"
#include <plat/flash.h>
#include <plat/mux.h>
#include <plat/tc.h>
#include <plat/usb.h>
+#include <mach/hardware.h>
+
+#include "common.h"
+
static struct plat_serial8250_port voiceblue_ports[] = {
{
.mapbase = (unsigned long)(OMAP_CS1_PHYS + 0x40000),
diff --git a/arch/arm/mach-omap1/clock.c b/arch/arm/mach-omap1/clock.c
index 0c50df0..0e8c176 100644
--- a/arch/arm/mach-omap1/clock.c
+++ b/arch/arm/mach-omap1/clock.c
@@ -16,7 +16,6 @@
#include <linux/errno.h>
#include <linux/err.h>
#include <linux/clk.h>
-#include <linux/io.h>
#include <linux/clkdev.h>
#include <asm/mach-types.h>
@@ -27,6 +26,7 @@
#include <plat/sram.h>
#include <plat/clkdev_omap.h>
+#include "iomap.h"
#include "clock.h"
#include "opp.h"
diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c
index 94699a8..10b7451 100644
--- a/arch/arm/mach-omap1/clock_data.c
+++ b/arch/arm/mach-omap1/clock_data.c
@@ -18,7 +18,6 @@
#include <linux/clk.h>
#include <linux/cpufreq.h>
#include <linux/delay.h>
-#include <linux/io.h>
#include <asm/mach-types.h> /* for machine_is_* */
@@ -28,6 +27,7 @@
#include <plat/sram.h> /* for omap_sram_reprogram_clock() */
#include <plat/usb.h> /* for OTG_BASE */
+#include "iomap.h"
#include "clock.h"
/* Some ARM_IDLECT1 bit shifts - used in struct arm_idlect1_clk */
diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c
index 1d76a63..d06c714 100644
--- a/arch/arm/mach-omap1/devices.c
+++ b/arch/arm/mach-omap1/devices.c
@@ -15,14 +15,10 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
-#include <linux/io.h>
#include <linux/spi/spi.h>
-#include <mach/camera.h>
-#include <mach/hardware.h>
#include <asm/mach/map.h>
-#include "common.h"
#include <plat/tc.h>
#include <plat/board.h>
#include <plat/mux.h>
@@ -30,6 +26,10 @@
#include <plat/omap7xx.h>
#include <plat/mcbsp.h>
+#include <mach/camera.h>
+#include <mach/hardware.h>
+
+#include "common.h"
#include "clock.h"
/*-------------------------------------------------------------------------*/
diff --git a/arch/arm/mach-omap1/dma.c b/arch/arm/mach-omap1/dma.c
index f5a5220..3ef7d52 100644
--- a/arch/arm/mach-omap1/dma.c
+++ b/arch/arm/mach-omap1/dma.c
@@ -19,11 +19,11 @@
*/
#include <linux/err.h>
-#include <linux/io.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/io.h>
#include <plat/dma.h>
#include <plat/tc.h>
diff --git a/arch/arm/mach-omap1/flash.c b/arch/arm/mach-omap1/flash.c
index 1749cb3..98d29a0 100644
--- a/arch/arm/mach-omap1/flash.c
+++ b/arch/arm/mach-omap1/flash.c
@@ -6,10 +6,10 @@
* published by the Free Software Foundation.
*/
+#include <linux/io.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/map.h>
-#include <plat/io.h>
#include <plat/tc.h>
#include <plat/flash.h>
diff --git a/arch/arm/mach-omap1/fpga.c b/arch/arm/mach-omap1/fpga.c
index 0a17a1a..76c67b3 100644
--- a/arch/arm/mach-omap1/fpga.c
+++ b/arch/arm/mach-omap1/fpga.c
@@ -24,12 +24,15 @@
#include <linux/errno.h>
#include <linux/io.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <plat/fpga.h>
+#include <mach/hardware.h>
+
+#include "iomap.h"
+
static void fpga_mask_irq(struct irq_data *d)
{
unsigned int irq = d->irq - OMAP_FPGA_IRQ_BASE;
diff --git a/arch/arm/mach-omap1/id.c b/arch/arm/mach-omap1/id.c
index a0e3560..7483db2 100644
--- a/arch/arm/mach-omap1/id.c
+++ b/arch/arm/mach-omap1/id.c
@@ -15,6 +15,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
+
#include <plat/cpu.h>
#define OMAP_DIE_ID_0 0xfffe1800
diff --git a/arch/arm/mach-omap1/include/mach/entry-macro.S b/arch/arm/mach-omap1/include/mach/entry-macro.S
index bfb4fb1..68d2679 100644
--- a/arch/arm/mach-omap1/include/mach/entry-macro.S
+++ b/arch/arm/mach-omap1/include/mach/entry-macro.S
@@ -9,10 +9,12 @@
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
+
#include <mach/hardware.h>
#include <mach/io.h>
#include <mach/irqs.h>
-#include <asm/hardware/gic.h>
+
+#include "../../iomap.h"
.macro disable_fiq
.endm
diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c
index 8e55b6f..56fb444 100644
--- a/arch/arm/mach-omap1/io.c
+++ b/arch/arm/mach-omap1/io.c
@@ -15,9 +15,12 @@
#include <asm/tlb.h>
#include <asm/mach/map.h>
+
#include <plat/mux.h>
#include <plat/tc.h>
+#include "iomap.h"
+#include "common.h"
#include "clock.h"
extern void omap_check_revision(void);
diff --git a/arch/arm/mach-omap1/iomap.h b/arch/arm/mach-omap1/iomap.h
new file mode 100644
index 0000000..d681757
--- /dev/null
+++ b/arch/arm/mach-omap1/iomap.h
@@ -0,0 +1,42 @@
+/*
+ * IO mappings for OMAP1
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifdef __ASSEMBLER__
+#define IOMEM(x) (x)
+#else
+#define IOMEM(x) ((void __force __iomem *)(x))
+#endif
+
+#define OMAP1_IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */
+#define OMAP1_IO_ADDRESS(pa) IOMEM((pa) - OMAP1_IO_OFFSET)
+
+/*
+ * ----------------------------------------------------------------------------
+ * Omap1 specific IO mapping
+ * ----------------------------------------------------------------------------
+ */
+
+#define OMAP1_IO_PHYS 0xFFFB0000
+#define OMAP1_IO_SIZE 0x40000
+#define OMAP1_IO_VIRT (OMAP1_IO_PHYS - OMAP1_IO_OFFSET)
diff --git a/arch/arm/mach-omap1/irq.c b/arch/arm/mach-omap1/irq.c
index e5b104b..4448114 100644
--- a/arch/arm/mach-omap1/irq.c
+++ b/arch/arm/mach-omap1/irq.c
@@ -42,11 +42,13 @@
#include <linux/interrupt.h>
#include <linux/io.h>
-#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
+
#include <plat/cpu.h>
+#include <mach/hardware.h>
+
#define IRQ_BANK(irq) ((irq) >> 5)
#define IRQ_BIT(irq) ((irq) & 0x1f)
diff --git a/arch/arm/mach-omap1/lcd_dma.c b/arch/arm/mach-omap1/lcd_dma.c
index 4538093..123a0df 100644
--- a/arch/arm/mach-omap1/lcd_dma.c
+++ b/arch/arm/mach-omap1/lcd_dma.c
@@ -27,9 +27,10 @@
#include <linux/interrupt.h>
#include <linux/io.h>
+#include <plat/dma.h>
+
#include <mach/hardware.h>
#include <mach/lcdc.h>
-#include <plat/dma.h>
int omap_lcd_dma_running(void)
{
diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c
index 91f9abb..3082d60 100644
--- a/arch/arm/mach-omap1/mcbsp.c
+++ b/arch/arm/mach-omap1/mcbsp.c
@@ -19,12 +19,15 @@
#include <linux/platform_device.h>
#include <linux/slab.h>
-#include <mach/irqs.h>
#include <plat/dma.h>
#include <plat/mux.h>
#include <plat/cpu.h>
#include <plat/mcbsp.h>
+#include <mach/irqs.h>
+
+#include "iomap.h"
+
#define DPS_RSTCT2_PER_EN (1 << 0)
#define DSP_RSTCT2_WD_PER_EN (1 << 1)
diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c
index 89ea20c..c06bb40 100644
--- a/arch/arm/mach-omap1/pm.c
+++ b/arch/arm/mach-omap1/pm.c
@@ -42,14 +42,13 @@
#include <linux/sysfs.h>
#include <linux/module.h>
#include <linux/io.h>
+#include <linux/atomic.h>
#include <asm/irq.h>
-#include <linux/atomic.h>
#include <asm/mach/time.h>
#include <asm/mach/irq.h>
#include <plat/cpu.h>
-#include <mach/irqs.h>
#include <plat/clock.h>
#include <plat/sram.h>
#include <plat/tc.h>
@@ -57,6 +56,9 @@
#include <plat/dma.h>
#include <plat/dmtimer.h>
+#include <mach/irqs.h>
+
+#include "iomap.h"
#include "pm.h"
static unsigned int arm_sleep_save[ARM_SLEEP_SAVE_SIZE];
diff --git a/arch/arm/mach-omap1/reset.c b/arch/arm/mach-omap1/reset.c
index 91d199b..f255b15 100644
--- a/arch/arm/mach-omap1/reset.c
+++ b/arch/arm/mach-omap1/reset.c
@@ -4,9 +4,10 @@
#include <linux/kernel.h>
#include <linux/io.h>
-#include <mach/hardware.h>
#include <plat/prcm.h>
+#include <mach/hardware.h>
+
void omap1_restart(char mode, const char *cmd)
{
/*
diff --git a/arch/arm/mach-omap1/sleep.S b/arch/arm/mach-omap1/sleep.S
index c875bdc..0779db1 100644
--- a/arch/arm/mach-omap1/sleep.S
+++ b/arch/arm/mach-omap1/sleep.S
@@ -33,8 +33,12 @@
*/
#include <linux/linkage.h>
+
#include <asm/assembler.h>
+
#include <mach/io.h>
+
+#include "iomap.h"
#include "pm.h"
.text
diff --git a/arch/arm/mach-omap1/sram.S b/arch/arm/mach-omap1/sram.S
index 692587d..2ce0b9a 100644
--- a/arch/arm/mach-omap1/sram.S
+++ b/arch/arm/mach-omap1/sram.S
@@ -9,10 +9,14 @@
*/
#include <linux/linkage.h>
+
#include <asm/assembler.h>
+
#include <mach/io.h>
#include <mach/hardware.h>
+#include "iomap.h"
+
.text
/*
diff --git a/arch/arm/mach-omap1/time.c b/arch/arm/mach-omap1/time.c
index b8faffa..2fae6a2 100644
--- a/arch/arm/mach-omap1/time.c
+++ b/arch/arm/mach-omap1/time.c
@@ -45,14 +45,15 @@
#include <linux/io.h>
#include <asm/system.h>
-#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/irq.h>
#include <asm/sched_clock.h>
+#include <mach/hardware.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
+#include "iomap.h"
#include "common.h"
#ifdef CONFIG_OMAP_MPU_TIMER
diff --git a/arch/arm/mach-omap1/timer32k.c b/arch/arm/mach-omap1/timer32k.c
index 9a54ef4..a2e6d07 100644
--- a/arch/arm/mach-omap1/timer32k.c
+++ b/arch/arm/mach-omap1/timer32k.c
@@ -47,14 +47,17 @@
#include <linux/io.h>
#include <asm/system.h>
-#include <mach/hardware.h>
#include <asm/leds.h>
#include <asm/irq.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
-#include "common.h"
+
#include <plat/dmtimer.h>
+#include <mach/hardware.h>
+
+#include "common.h"
+
/*
* ---------------------------------------------------------------------------
* 32KHz OS timer
diff --git a/arch/arm/plat-omap/include/plat/io.h b/arch/arm/plat-omap/include/plat/io.h
index 28cd796..e5e8e08 100644
--- a/arch/arm/plat-omap/include/plat/io.h
+++ b/arch/arm/plat-omap/include/plat/io.h
@@ -60,9 +60,6 @@
#define IOMEM(x) ((void __force __iomem *)(x))
#endif
-#define OMAP1_IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */
-#define OMAP1_IO_ADDRESS(pa) IOMEM((pa) - OMAP1_IO_OFFSET)
-
#define OMAP2_L3_IO_OFFSET 0x90000000
#define OMAP2_L3_IO_ADDRESS(pa) IOMEM((pa) + OMAP2_L3_IO_OFFSET) /* L3 */
@@ -87,16 +84,6 @@
/*
* ----------------------------------------------------------------------------
- * Omap1 specific IO mapping
- * ----------------------------------------------------------------------------
- */
-
-#define OMAP1_IO_PHYS 0xFFFB0000
-#define OMAP1_IO_SIZE 0x40000
-#define OMAP1_IO_VIRT (OMAP1_IO_PHYS - OMAP1_IO_OFFSET)
-
-/*
- * ----------------------------------------------------------------------------
* Omap2 specific IO mapping
* ----------------------------------------------------------------------------
*/
next prev parent reply other threads:[~2012-02-23 23:44 UTC|newest]
Thread overview: 79+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-02-21 23:40 [PATCH 0/8] Split omap plat/io.h into local iomap.h files Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-21 23:40 ` [PATCH 1/8] ARM: OMAP2+: Move DISPC L3 firewall to happen in omap_display_init() Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-22 8:09 ` Tomi Valkeinen
2012-02-22 8:09 ` Tomi Valkeinen
2012-02-22 8:09 ` Tomi Valkeinen
2012-02-22 19:05 ` Tony Lindgren
2012-02-22 19:05 ` Tony Lindgren
2012-02-22 19:05 ` Tony Lindgren
2012-02-22 22:17 ` Tony Lindgren
2012-02-22 22:17 ` Tony Lindgren
2012-02-22 22:17 ` Tony Lindgren
2012-02-21 23:40 ` [PATCH 2/8] ARM: OMAP2+: Move SDRC related functions from io.h into local common.h Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-21 23:40 ` [PATCH 3/8] ARM: OMAP: Move omap_init_consistent_dma_size() to " Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-21 23:40 ` [PATCH 4/8] ARM: OMAP1: Move 16xx GPIO system clock to platform init code Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-23 23:42 ` Tony Lindgren
2012-02-23 23:42 ` Tony Lindgren
2012-03-12 17:30 ` Grant Likely
2012-03-12 17:30 ` Grant Likely
2012-03-12 18:05 ` Tony Lindgren
2012-03-12 18:05 ` Tony Lindgren
2012-02-21 23:40 ` [PATCH 5/8] ARM: OMAP1: Move most of plat/io.h into local iomap.h Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-23 23:44 ` Tony Lindgren [this message]
2012-02-23 23:44 ` Tony Lindgren
2012-02-21 23:40 ` [PATCH 6/8] ARM: OMAP2+: " Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-23 23:46 ` Tony Lindgren
2012-02-23 23:46 ` Tony Lindgren
2012-02-21 23:40 ` [PATCH 7/8] ARM: OMAP: Remove plat/io.h by moving it into mach/io.h Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-22 2:24 ` Rob Herring
2012-02-22 2:24 ` Rob Herring
2012-02-24 0:06 ` Tony Lindgren
2012-02-24 0:06 ` Tony Lindgren
2012-02-24 18:22 ` Tony Lindgren
2012-02-24 18:22 ` Tony Lindgren
2012-02-27 3:47 ` Rob Herring
2012-02-27 3:47 ` Rob Herring
2012-02-29 1:47 ` Tony Lindgren
2012-02-29 1:47 ` Tony Lindgren
2012-02-29 1:49 ` Tony Lindgren
2012-02-29 1:49 ` Tony Lindgren
2012-02-29 23:59 ` Rob Herring
2012-02-29 23:59 ` Rob Herring
2012-03-01 0:11 ` Russell King - ARM Linux
2012-03-01 0:11 ` Russell King - ARM Linux
2012-03-01 0:39 ` Tony Lindgren
2012-03-01 0:39 ` Tony Lindgren
2012-03-01 1:03 ` Tony Lindgren
2012-03-01 1:03 ` Tony Lindgren
2012-03-01 3:34 ` Rob Herring
2012-03-01 3:34 ` Rob Herring
2012-03-01 3:46 ` Tony Lindgren
2012-03-01 3:46 ` Tony Lindgren
2012-03-01 3:53 ` Rob Herring
2012-03-01 3:53 ` Rob Herring
2012-03-01 4:54 ` Tony Lindgren
2012-03-01 4:54 ` Tony Lindgren
2012-02-21 23:40 ` [PATCH 8/8] ARM: OMAP2+: Limit omap_read/write usage to legacy USB drivers Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-21 23:40 ` Tony Lindgren
2012-02-22 8:14 ` Tomi Valkeinen
2012-02-22 8:14 ` Tomi Valkeinen
2012-02-22 8:14 ` Tomi Valkeinen
2012-02-22 18:57 ` Tony Lindgren
2012-02-22 18:57 ` Tony Lindgren
2012-02-22 18:57 ` Tony Lindgren
2012-02-22 22:44 ` Tony Lindgren
2012-02-22 22:44 ` Tony Lindgren
2012-02-22 22:44 ` Tony Lindgren
2012-02-24 18:25 ` Tony Lindgren
2012-02-24 18:25 ` Tony Lindgren
2012-02-24 18:25 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120223234447.GH18185@atomide.com \
--to=tony@atomide.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.