[PATCH 38/47] gma500: oaktrail_hdmi: drop dead code

[Alan Cox <alan@lxorguk.ukuu.org.uk>]

From: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>

Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
---

 drivers/gpu/drm/gma500/oaktrail_hdmi.c |  327 --------------------------------
 1 files changed, 0 insertions(+), 327 deletions(-)


diff --git a/drivers/gpu/drm/gma500/oaktrail_hdmi.c b/drivers/gpu/drm/gma500/oaktrail_hdmi.c
index e4c73c6..f3fc693 100644
--- a/drivers/gpu/drm/gma500/oaktrail_hdmi.c
+++ b/drivers/gpu/drm/gma500/oaktrail_hdmi.c
@@ -125,59 +125,6 @@ static const struct oaktrail_hdmi_limit oaktrail_hdmi_limit = {
 	.nf  = { .min = NF_MIN,			.max = NF_MAX  },
 };
 
-static void wait_for_vblank(struct drm_device *dev)
-{
-	/* FIXME: Can we do this as a sleep ? */
-	/* Wait for 20ms, i.e. one cycle at 50hz. */
-	mdelay(20);
-}
-
-static void scu_busy_loop(void *scu_base)
-{
-	u32 status = 0;
-	u32 loop_count = 0;
-
-	status = readl(scu_base + 0x04);
-	while (status & 1) {
-		udelay(1); /* scu processing time is in few u secods */
-		status = readl(scu_base + 0x04);
-		loop_count++;
-		/* break if scu doesn't reset busy bit after huge retry */
-		if (loop_count > 1000) {
-			DRM_DEBUG_KMS("SCU IPC timed out");
-			return;
-		}
-	}
-}
-
-static void oaktrail_hdmi_reset(struct drm_device *dev)
-{
-	void *base;
-	/* FIXME: at least make these defines */
-	unsigned int scu_ipc_mmio = 0xff11c000;
-	int scu_len = 1024;
-
-	base = ioremap((resource_size_t)scu_ipc_mmio, scu_len);
-	if (base == NULL) {
-		DRM_ERROR("failed to map SCU mmio\n");
-		return;
-	}
-
-	/* scu ipc: assert hdmi controller reset */
-	writel(0xff11d118, base + 0x0c);
-	writel(0x7fffffdf, base + 0x80);
-	writel(0x42005, base + 0x0);
-	scu_busy_loop(base);
-
-	/* scu ipc: de-assert hdmi controller reset */
-	writel(0xff11d118, base + 0x0c);
-	writel(0x7fffffff, base + 0x80);
-	writel(0x42005, base + 0x0);
-	scu_busy_loop(base);
-
-	iounmap(base);
-}
-
 static void oaktrail_hdmi_audio_enable(struct drm_device *dev)
 {
 	struct drm_psb_private *dev_priv = dev->dev_private;
@@ -208,104 +155,6 @@ static void oaktrail_hdmi_audio_disable(struct drm_device *dev)
 	HDMI_READ(HDMI_HCR);
 }
 
-void oaktrail_crtc_hdmi_dpms(struct drm_crtc *crtc, int mode)
-{
-	struct drm_device *dev = crtc->dev;
-	u32 temp;
-
-	switch (mode) {
-	case DRM_MODE_DPMS_OFF:
-		/* Disable VGACNTRL */
-		REG_WRITE(VGACNTRL, 0x80000000);
-
-		/* Disable plane */
-		temp = REG_READ(DSPBCNTR);
-		if ((temp & DISPLAY_PLANE_ENABLE) != 0) {
-			REG_WRITE(DSPBCNTR, temp & ~DISPLAY_PLANE_ENABLE);
-			REG_READ(DSPBCNTR);
-			/* Flush the plane changes */
-			REG_WRITE(DSPBSURF, REG_READ(DSPBSURF));
-			REG_READ(DSPBSURF);
-		}
-
-		/* Disable pipe B */
-		temp = REG_READ(PIPEBCONF);
-		if ((temp & PIPEACONF_ENABLE) != 0) {
-			REG_WRITE(PIPEBCONF, temp & ~PIPEACONF_ENABLE);
-			REG_READ(PIPEBCONF);
-		}
-
-		/* Disable LNW Pipes, etc */
-		temp = REG_READ(PCH_PIPEBCONF);
-		if ((temp & PIPEACONF_ENABLE) != 0) {
-			REG_WRITE(PCH_PIPEBCONF, temp & ~PIPEACONF_ENABLE);
-			REG_READ(PCH_PIPEBCONF);
-		}
-		/* wait for pipe off */
-		udelay(150);
-		/* Disable dpll */
-		temp = REG_READ(DPLL_CTRL);
-		if ((temp & DPLL_PWRDN) == 0) {
-			REG_WRITE(DPLL_CTRL, temp | (DPLL_PWRDN | DPLL_RESET));
-			REG_WRITE(DPLL_STATUS, 0x1);
-		}
-		/* wait for dpll off */
-		udelay(150);
-		break;
-	case DRM_MODE_DPMS_ON:
-	case DRM_MODE_DPMS_STANDBY:
-	case DRM_MODE_DPMS_SUSPEND:
-		/* Enable dpll */
-		temp = REG_READ(DPLL_CTRL);
-		if ((temp & DPLL_PWRDN) != 0) {
-			REG_WRITE(DPLL_CTRL, temp & ~(DPLL_PWRDN | DPLL_RESET));
-			temp = REG_READ(DPLL_CLK_ENABLE);
-			REG_WRITE(DPLL_CLK_ENABLE, temp | DPLL_EN_DISP | DPLL_SEL_HDMI | DPLL_EN_HDMI);
-			REG_READ(DPLL_CLK_ENABLE);
-		}
-		/* wait for dpll warm up */
-		udelay(150);
-
-		/* Enable pipe B */
-		temp = REG_READ(PIPEBCONF);
-		if ((temp & PIPEACONF_ENABLE) == 0) {
-			REG_WRITE(PIPEBCONF, temp | PIPEACONF_ENABLE);
-			REG_READ(PIPEBCONF);
-		}
-
-		/* Enable LNW Pipe B */
-		temp = REG_READ(PCH_PIPEBCONF);
-		if ((temp & PIPEACONF_ENABLE) == 0) {
-			REG_WRITE(PCH_PIPEBCONF, temp | PIPEACONF_ENABLE);
-			REG_READ(PCH_PIPEBCONF);
-		}
-		wait_for_vblank(dev);
-
-		/* Enable plane */
-		temp = REG_READ(DSPBCNTR);
-		if ((temp & DISPLAY_PLANE_ENABLE) == 0) {
-			REG_WRITE(DSPBCNTR, temp | DISPLAY_PLANE_ENABLE);
-			/* Flush the plane changes */
-			REG_WRITE(DSPBSURF, REG_READ(DSPBSURF));
-			REG_READ(DSPBSURF);
-		}
-		psb_intel_crtc_load_lut(crtc);
-	}
-	/* DSPARB */
-	REG_WRITE(DSPARB, 0x00003fbf);
-	/* FW1 */
-	REG_WRITE(0x70034, 0x3f880a0a);
-	/* FW2 */
-	REG_WRITE(0x70038, 0x0b060808);
-	/* FW4 */
-	REG_WRITE(0x70050, 0x08030404);
-	/* FW5 */
-	REG_WRITE(0x70054, 0x04040404);
-	/* LNC Chicken Bits */
-	REG_WRITE(0x70400, 0x4000);
-}
-
-
 static void oaktrail_hdmi_dpms(struct drm_encoder *encoder, int mode)
 {
 	static int dpms_mode = -1;
@@ -327,182 +176,6 @@ static void oaktrail_hdmi_dpms(struct drm_encoder *encoder, int mode)
 	HDMI_WRITE(HDMI_VIDEO_REG, temp);
 }
 
-static unsigned int htotal_calculate(struct drm_display_mode *mode)
-{
-	u32 htotal, new_crtc_htotal;
-
-	htotal = (mode->crtc_hdisplay - 1) | ((mode->crtc_htotal - 1) << 16);
-
-	/*
-	 * 1024 x 768  new_crtc_htotal = 0x1024;
-	 * 1280 x 1024 new_crtc_htotal = 0x0c34;
-	 */
-	new_crtc_htotal = (mode->crtc_htotal - 1) * 200 * 1000 / mode->clock;
-
-	return (mode->crtc_hdisplay - 1) | (new_crtc_htotal << 16);
-}
-
-static void oaktrail_hdmi_find_dpll(struct drm_crtc *crtc, int target,
-				int refclk, struct oaktrail_hdmi_clock *best_clock)
-{
-	int np_min, np_max, nr_min, nr_max;
-	int np, nr, nf;
-
-	np_min = DIV_ROUND_UP(oaktrail_hdmi_limit.vco.min, target * 10);
-	np_max = oaktrail_hdmi_limit.vco.max / (target * 10);
-	if (np_min < oaktrail_hdmi_limit.np.min)
-		np_min = oaktrail_hdmi_limit.np.min;
-	if (np_max > oaktrail_hdmi_limit.np.max)
-		np_max = oaktrail_hdmi_limit.np.max;
-
-	nr_min = DIV_ROUND_UP((refclk * 1000), (target * 10 * np_max));
-	nr_max = DIV_ROUND_UP((refclk * 1000), (target * 10 * np_min));
-	if (nr_min < oaktrail_hdmi_limit.nr.min)
-		nr_min = oaktrail_hdmi_limit.nr.min;
-	if (nr_max > oaktrail_hdmi_limit.nr.max)
-		nr_max = oaktrail_hdmi_limit.nr.max;
-
-	np = DIV_ROUND_UP((refclk * 1000), (target * 10 * nr_max));
-	nr = DIV_ROUND_UP((refclk * 1000), (target * 10 * np));
-	nf = DIV_ROUND_CLOSEST((target * 10 * np * nr), refclk);
-	DRM_DEBUG_KMS("np, nr, nf %d %d %d\n", np, nr, nf);
-
-	/*
-	 * 1024 x 768  np = 1; nr = 0x26; nf = 0x0fd8000;
-	 * 1280 x 1024 np = 1; nr = 0x17; nf = 0x1034000;
-	 */
-	best_clock->np = np;
-	best_clock->nr = nr - 1;
-	best_clock->nf = (nf << 14);
-}
-
-int oaktrail_crtc_hdmi_mode_set(struct drm_crtc *crtc,
-			    struct drm_display_mode *mode,
-			    struct drm_display_mode *adjusted_mode,
-			    int x, int y,
-			    struct drm_framebuffer *old_fb)
-{
-	struct drm_device *dev = crtc->dev;
-	struct drm_psb_private *dev_priv = dev->dev_private;
-	struct oaktrail_hdmi_dev *hdmi_dev = dev_priv->hdmi_priv;
-	int pipe = 1;
-	int htot_reg = (pipe == 0) ? HTOTAL_A : HTOTAL_B;
-	int hblank_reg = (pipe == 0) ? HBLANK_A : HBLANK_B;
-	int hsync_reg = (pipe == 0) ? HSYNC_A : HSYNC_B;
-	int vtot_reg = (pipe == 0) ? VTOTAL_A : VTOTAL_B;
-	int vblank_reg = (pipe == 0) ? VBLANK_A : VBLANK_B;
-	int vsync_reg = (pipe == 0) ? VSYNC_A : VSYNC_B;
-	int dspsize_reg = (pipe == 0) ? DSPASIZE : DSPBSIZE;
-	int dsppos_reg = (pipe == 0) ? DSPAPOS : DSPBPOS;
-	int pipesrc_reg = (pipe == 0) ? PIPEASRC : PIPEBSRC;
-	int pipeconf_reg = (pipe == 0) ? PIPEACONF : PIPEBCONF;
-	int refclk;
-	struct oaktrail_hdmi_clock clock;
-	u32 dspcntr, pipeconf, dpll, temp;
-	int dspcntr_reg = DSPBCNTR;
-
-	/* Disable the VGA plane that we never use */
-	REG_WRITE(VGACNTRL, VGA_DISP_DISABLE);
-
-	/* XXX: Disable the panel fitter if it was on our pipe */
-
-	/* Disable dpll if necessary */
-	dpll = REG_READ(DPLL_CTRL);
-	if ((dpll & DPLL_PWRDN) == 0) {
-		REG_WRITE(DPLL_CTRL, dpll | (DPLL_PWRDN | DPLL_RESET));
-		REG_WRITE(DPLL_DIV_CTRL, 0x00000000);
-		REG_WRITE(DPLL_STATUS, 0x1);
-	}
-	udelay(150);
-
-	/* reset controller: FIXME - can we sort out the ioremap mess ? */
-	iounmap(hdmi_dev->regs);
-	oaktrail_hdmi_reset(dev);
-
-	/* program and enable dpll */
-	refclk = 25000;
-	oaktrail_hdmi_find_dpll(crtc, adjusted_mode->clock, refclk, &clock);
-
-	/* Setting DPLL */
-	dpll = REG_READ(DPLL_CTRL);
-	dpll &= ~DPLL_PDIV_MASK;
-	dpll &= ~(DPLL_PWRDN | DPLL_RESET);
-	REG_WRITE(DPLL_CTRL, 0x00000008);
-	REG_WRITE(DPLL_DIV_CTRL, ((clock.nf << 6) | clock.nr));
-	REG_WRITE(DPLL_ADJUST, ((clock.nf >> 14) - 1));
-	REG_WRITE(DPLL_CTRL, (dpll | (clock.np << DPLL_PDIV_SHIFT) | DPLL_ENSTAT | DPLL_DITHEN));
-	REG_WRITE(DPLL_UPDATE, 0x80000000);
-	REG_WRITE(DPLL_CLK_ENABLE, 0x80050102);
-	udelay(150);
-
-	hdmi_dev->regs = ioremap(hdmi_dev->mmio, hdmi_dev->mmio_len);
-	if (hdmi_dev->regs == NULL) {
-		DRM_ERROR("failed to do hdmi mmio mapping\n");
-		return -ENOMEM;
-	}
-
-	/* configure HDMI */
-	HDMI_WRITE(0x1004, 0x1fd);
-	HDMI_WRITE(0x2000, 0x1);
-	HDMI_WRITE(0x2008, 0x0);
-	HDMI_WRITE(0x3130, 0x8);
-	HDMI_WRITE(0x101c, 0x1800810);
-
-	temp = htotal_calculate(adjusted_mode);
-	REG_WRITE(htot_reg, temp);
-	REG_WRITE(hblank_reg, (adjusted_mode->crtc_hblank_start - 1) | ((adjusted_mode->crtc_hblank_end - 1) << 16));
-	REG_WRITE(hsync_reg, (adjusted_mode->crtc_hsync_start - 1) | ((adjusted_mode->crtc_hsync_end - 1) << 16));
-	REG_WRITE(vtot_reg, (adjusted_mode->crtc_vdisplay - 1) | ((adjusted_mode->crtc_vtotal - 1) << 16));
-	REG_WRITE(vblank_reg, (adjusted_mode->crtc_vblank_start - 1) | ((adjusted_mode->crtc_vblank_end - 1) << 16));
-	REG_WRITE(vsync_reg, (adjusted_mode->crtc_vsync_start - 1) | ((adjusted_mode->crtc_vsync_end - 1) << 16));
-	REG_WRITE(pipesrc_reg,
-		((mode->crtc_hdisplay - 1) << 16) |  (mode->crtc_vdisplay - 1));
-
-	REG_WRITE(PCH_HTOTAL_B, (adjusted_mode->crtc_hdisplay - 1) | ((adjusted_mode->crtc_htotal - 1) << 16));
-	REG_WRITE(PCH_HBLANK_B, (adjusted_mode->crtc_hblank_start - 1) | ((adjusted_mode->crtc_hblank_end - 1) << 16));
-	REG_WRITE(PCH_HSYNC_B, (adjusted_mode->crtc_hsync_start - 1) | ((adjusted_mode->crtc_hsync_end - 1) << 16));
-	REG_WRITE(PCH_VTOTAL_B, (adjusted_mode->crtc_vdisplay - 1) | ((adjusted_mode->crtc_vtotal - 1) << 16));
-	REG_WRITE(PCH_VBLANK_B, (adjusted_mode->crtc_vblank_start - 1) | ((adjusted_mode->crtc_vblank_end - 1) << 16));
-	REG_WRITE(PCH_VSYNC_B, (adjusted_mode->crtc_vsync_start - 1) | ((adjusted_mode->crtc_vsync_end - 1) << 16));
-	REG_WRITE(PCH_PIPEBSRC,
-		((mode->crtc_hdisplay - 1) << 16) |  (mode->crtc_vdisplay - 1));
-
-	temp = adjusted_mode->crtc_hblank_end - adjusted_mode->crtc_hblank_start;
-	HDMI_WRITE(HDMI_HBLANK_A, ((adjusted_mode->crtc_hdisplay - 1) << 16) |  temp);
-
-	REG_WRITE(dspsize_reg,
-			((mode->vdisplay - 1) << 16) | (mode->hdisplay - 1));
-	REG_WRITE(dsppos_reg, 0);
-
-	/* Flush the plane changes */
-	{
-		struct drm_crtc_helper_funcs *crtc_funcs = crtc->helper_private;
-		crtc_funcs->mode_set_base(crtc, x, y, old_fb);
-	}
-
-	/* Set up the display plane register */
-	dspcntr = REG_READ(dspcntr_reg);
-	dspcntr |= DISPPLANE_GAMMA_ENABLE;
-	dspcntr |= DISPPLANE_SEL_PIPE_B;
-	dspcntr |= DISPLAY_PLANE_ENABLE;
-
-	/* setup pipeconf */
-	pipeconf = REG_READ(pipeconf_reg);
-	pipeconf |= PIPEACONF_ENABLE;
-
-	REG_WRITE(pipeconf_reg, pipeconf);
-	REG_READ(pipeconf_reg);
-
-	REG_WRITE(PCH_PIPEBCONF, pipeconf);
-	REG_READ(PCH_PIPEBCONF);
-	wait_for_vblank(dev);
-
-	REG_WRITE(dspcntr_reg, dspcntr);
-	wait_for_vblank(dev);
-
-	return 0;
-}
-
 static int oaktrail_hdmi_mode_valid(struct drm_connector *connector,
 				struct drm_display_mode *mode)
 {